Engines · Chapter 2
Piston Engine Construction and Operation Cylinder layouts, the four-stroke Otto cycle and its valve timing, power and efficiency, compression ratio, and every major part of the engine.
INDUCTION · COMPRESSION · POWER · EXHAUST
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter two takes the piston engine apart. We start with how cylinders are arranged, in-line, vee, radial and horizontally opposed. Then we follow the four-stroke Otto cycle through two turns of the crankshaft, first in theory and then as real engines are timed, with valve lead, lag and overlap. We measure what the engine produces, with the indicator diagram, indicated and brake horsepower, specific fuel consumption and the three efficiencies, and we work out compression ratios. Finally we look at every main part: crankcase, crankshaft, connecting rods, pistons and rings, cylinders, valves, valve gear and accessories.
Roadmap
Inside the piston engine 1 · Layouts In-line, vee, radial and flat engines: why each exists and how they fire.
2 · The Otto cycle Four strokes, five events; theoretical and practical valve timing.
3 · Power and efficiency Indicator diagram, IMEP, IHP, BHP, SFC, efficiencies, compression ratio.
4 · Construction Crankshaft, rods, pistons, cylinders, valves, valve gear, accessories.
Chapter 2 · Piston Engine Construction and Operation
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. In the first we look at how the cylinders are arranged: in-line, vee, radial and horizontally opposed, and why each arrangement was chosen. In the second we follow the four-stroke Otto cycle through its seven hundred and twenty degrees, first in theory with every event at a dead centre, and then as real engines are timed, with valve lead, lag and overlap. In the third part we measure what comes out: the indicator diagram, mean effective pressure, indicated and brake horsepower, specific fuel consumption, the three efficiencies and compression ratio, with worked numbers. In the last part we take the engine apart: crankcase and crankshaft, connecting rods, pistons and rings, cylinders and heads, valves and valve gear, valve clearance, and the accessories and gearing. Many exam questions come straight from definitions in this chapter, so learn the words exactly.
Part 1 · Layouts
In-line and vee engines More power is best found by adding more cylinders , not one bigger cylinder: more power and smoother running Layout depends on cooling , power and the aircraft's role In-line : cylinders one behind another; air-cooled versions limited to about six ; often inverted for propeller clearanceVee : two banks of in-line cylinders, 8 to 12 , usually liquid cooled ; slim and streamlined, but heavy and complexTypical in-line four firing order: 1-3-4-2
In-line Vee (V-12) cylinders one behind another propeller on the crankshaft • air-cooled: up to about six • often inverted: crank on top, more propeller clearance • slim: low frontal area seen from the front • 8 to 12 cylinders, high power • liquid cooled: streamlined into the fuselage • but heavier and more complex • WW2 fighters; can be inverted
Chapter 2 · Piston Engine Construction and Operation
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
To get more power from an engine it is better to add cylinders than to make one cylinder bigger. More cylinders give more power strokes in each cycle, so the engine also runs more smoothly. How the cylinders are arranged depends on the type of cooling, the power needed and the role of the aircraft. Early aircraft used in-line engines, with the cylinders one behind another along the crankshaft. Air-cooled in-line engines are limited to about six cylinders, because the rear ones get too little cooling air, and many were inverted, with the crankshaft on top, which raises the propeller and gives it more ground clearance. The vee engine puts two in-line banks on one crankshaft, eight to twelve cylinders, and powered the fighters of the Second World War. Liquid cooled and slim, it streamlined neatly into the fuselage, but the cooling system added weight and complexity. Watch the firing order read-out on this in-line four.
Part 1 · Layouts
Radial engines Cylinders arranged radially round a single crank: short, light, rigid and powerful Air-cooled, with a large frontal area and so more drag Always an odd number of cylinders per row, so firing every second cylinder gives even intervals One master rod on the crankpin; the others are articulated rods on knuckle pins Double and triple bank radials: more power, but heavy; lower cylinders can suffer hydraulicing
1 2 3 4 5 6 7 8 9 Firing order 1-3-5-7-9-2-4-6-8: every second cylinder Nine cylinders, one row
Chapter 2 · Piston Engine Construction and Operation
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a radial engine the cylinders are arranged like the spokes of a wheel round a single crank. The engine is short, light for its power and very rigid, but it presents a large frontal area to the air, so it adds drag. Radials are air-cooled, and each row always has an odd number of cylinders. Why odd? The engine fires every second cylinder: here one, three, five, seven, nine, then two, four, six, eight. With an odd number, that pattern comes round evenly, giving equal firing intervals. Only one connecting rod, the master rod, is attached to the crank; all the others are articulated rods pinned to the master rod. Watch how they swing. Putting further rows behind the first gives double and triple bank radials, very powerful but heavy. And because oil can drain into the lower cylinders, radials can suffer from hydraulicing, which we meet in the lubrication chapter.
Part 1 · Layouts
Horizontally opposed engines Most modern light aircraft: four or six cylinders, horizontally opposed Two banks, one each side of the crankshaft, slightly staggered Short, rigid and easily streamlined in a light-aircraft nose Opposed pistons balance each other well: smooth running Lycoming numbering: 1, 3, 5 on the right; firing order of the four: 1-3-2-4
Horizontally opposed four, seen from above propeller end 1 3 2 4 right bank: 1, 3 left bank: 2, 4 Firing order 1-3-2-4 (Lycoming)
Chapter 2 · Piston Engine Construction and Operation
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Almost every modern light aircraft has a horizontally opposed engine of four or six cylinders. The cylinders lie flat in two banks, one each side of the crankshaft, and the two banks are slightly staggered so that each connecting rod can reach its own crank throw. The result is a short, rigid engine that fits neatly behind a propeller in a streamlined nose, and because opposite pistons move in opposite directions, their forces largely cancel and the engine runs smoothly. In the scene you are looking from behind, as the pilot would. On Lycoming engines the odd-numbered cylinders are on the right bank, and the right bank sits slightly further forward. The firing order of a Lycoming four is one, three, two, four, which you can see lighting up in the read-out. Do not mix it up with the typical in-line four order of one, three, four, two.
Part 2 · The Otto cycle
Stroke, bore and dead centres Stroke : the distance the piston moves between its two end pointsTop dead centre (TDC) and bottom dead centre (BDC) : the ends of the strokeTDC to BDC = 180° of crank; one cycle = 720° (four strokes) Stroke = 2 × crank throw Bore : the internal diameter of the cylinder; bore equal to stroke is called square , bore greater than stroke over-square
TDC BDC stroke bore crank throw stroke = 2 × throw 180° of crank per stroke
Chapter 2 · Piston Engine Construction and Operation
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
A few terms first. A stroke is the distance the piston moves in the cylinder from one end of its travel to the other. When the piston is at the top it is at top dead centre, and at the bottom it is at bottom dead centre. The word dead is used because, at those two points, the piston stops for an instant and the connecting rod is in line with the crank. Moving the piston from top to bottom dead centre takes one hundred and eighty degrees of crankshaft rotation, so the four strokes of the cycle take seven hundred and twenty degrees. The offset of the crankpin from the shaft centre is the crank throw, and the stroke is always twice the crank throw. The internal diameter of the cylinder is the bore. An engine whose bore equals its stroke is called square; one with a bore larger than its stroke is called over-square.
Part 2 · The Otto cycle
The four strokes
1 · Induction inlet open, piston down 2 · Compression both shut, piston up 3 · Power both shut, gas drives piston down 4 · Exhaust exhaust open, piston up
Chapter 2 · Piston Engine Construction and Operation
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the four strokes in order. Induction: the inlet valve is open and the piston moves down, drawing mixture into the cylinder. Compression: both valves are shut and the piston rises, squeezing the mixture. Near the top, a spark ignites it. Power: both valves are still shut, and the burning gas drives the piston down. This is the only stroke that delivers power to the crankshaft; in some questions it is called the expansion stroke. Exhaust: the exhaust valve opens and the rising piston pushes the burnt gas out. Then the cycle repeats. Notice that the cycle takes two complete turns of the crankshaft, so induction and compression together take one turn, and power and exhaust take the next. The correct order is induction, compression, power, exhaust, and any list that keeps that sequence, starting at a different stroke, describes the same cycle.
Part 2 · The Otto cycle
The theoretical cycle: five events at the dead centres Four strokes, but five events : induction, compression, combustion , power, exhaust The spark ignites the mixture at TDC: not an explosion but a controlled burning Temperature and pressure rise as the mixture burns In theory combustion is instant, at TDC, so it happens at constant volume In theory each valve opens and closes exactly at a dead centre
TDC BDC Theoretical Otto cycle: events at the dead centres outer ring: inlet open inner ring: exhaust open spark at TDC Combustion at TDC: constant volume 1st turn: induction 2nd turn: power 1st turn: compression 2nd turn: exhaust
Chapter 2 · Piston Engine Construction and Operation
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
In the theoretical Otto cycle everything happens exactly at the dead centres. The inlet valve opens at top dead centre and closes at bottom dead centre, the exhaust valve opens at bottom dead centre and closes at top dead centre, and the spark occurs exactly at top dead centre at the end of compression. Although there are four strokes there are five events, because combustion is an event of its own. It is important to understand that the mixture does not explode. A flame spreads through it in a controlled burning, and as it burns the temperature and pressure of the gas rise steeply. In the theoretical cycle that burning is instantaneous, and since the piston is at top dead centre at that moment, the volume does not change: combustion is said to take place at constant volume. That phrase, constant volume, is a favourite exam answer, so remember it.
Part 2 · Practical timing
The induction stroke in practice The theoretical timing proved inefficient ; real engines open and close valves early or late Inlet opens before TDC : fully open early, so there is no lag as the piston descends The inflowing mixture gains momentum and keeps flowing after BDC Inlet closes after BDC , when cylinder pressure ≈ manifold pressure Result: a greater weight of mixture is induced
0 90 180 235 0.8 1.0 1.2 crank angle after TDC (degrees) pressure (bar) manifold pressure inlet closes 55° after BDC piston "pulls" ahead of the reluctant mixture momentum still fills the cylinder Close the inlet when cylinder pressure ≈ manifold pressure: the greatest weight of charge is then trapped
Chapter 2 · Piston Engine Construction and Operation
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Real engines do not use the theoretical timing, because it wastes much of the cycle. Start with induction. Because of the inertia of the mixture, if the inlet valve only began to open at top dead centre, the piston would already be moving down before the mixture got going, and the cylinder would be poorly filled. So the inlet valve opens before top dead centre, and is wide open early in the stroke. As the induction stroke goes on, the column of mixture in the induction pipe gathers momentum. Near the end of the stroke that momentum is enough to keep the mixture flowing into the cylinder even after the piston has passed bottom dead centre and started to rise. So the inlet valve is closed late, after bottom dead centre, at about the point where the cylinder pressure has risen to equal the manifold pressure. The whole purpose is to induce a greater weight of mixture.
Part 2 · Practical timing
Compression and power strokes in practice Compression heats the charge adiabatically (like a bicycle pump), so pressure rises more than the volume change alone gives The spark fires before TDC : momentum carries the piston over while the flame spreads Peak pressure is reached when combustion is complete , about 10° after TDC By 45° after TDC pressure is about half its peak; by 90° most of the energy has been used Exhaust opens before BDC : pressure scavenging, little useful work lost
-60 -25 0 45 90 125 180 0 10 20 30 40 50 crank angle from TDC (degrees) cylinder pressure (bar) peak ≈ 12° after TDC about half the peak by 45° spark 25° BTDC exhaust opens 55° before BDC Ignition early, peak just after TDC, exhaust opened early (computed from a simple burn model, compression ratio 8.5)
Chapter 2 · Piston Engine Construction and Operation
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the compression stroke the mixture is squeezed so quickly that it heats up adiabatically, just as a bicycle pump gets warm, and it also picks up heat from the hot cylinder. So its pressure rises higher than the reduction in volume alone would give. The flame takes time to spread, so the spark fires before top dead centre, here twenty-five degrees before. The momentum of the moving parts carries the piston over the top while the flame spreads. Pressure reaches its peak when combustion is complete, at about ten degrees after top dead centre. During the first few degrees of the power stroke the temperature still rises, then pressure and temperature fall quickly: by forty-five degrees the pressure is about half its peak, and by ninety most of the energy has been turned into work. The exhaust valve then opens before bottom dead centre, so the remaining pressure starts pushing the gas out.
Part 2 · Practical timing
The exhaust stroke and the ineffective crank angle Opening the exhaust early costs little: the piston has little travel left and the gas has little pressure left By BDC the cylinder has blown down: no back pressure on the rising piston Exhaust valve closes after TDC : the moving gas scavenges the cylinder by its momentum Near TDC and BDC the piston hardly moves for many degrees of crank: the ineffective crank angle That is why valves can open early and close late without upsetting the volume
0 20 90 180 270 360 0 0.25 0.5 0.75 1 crank angle from TDC (degrees) piston travel (× stroke) ineffective ineffective First 20° after TDC: piston moves only 4 % of the stroke 20° around mid-stroke (80–100°): 17 % of the stroke Last 20° before BDC: only 2 % of the stroke
Chapter 2 · Piston Engine Construction and Operation
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why is it safe to open the exhaust valve before bottom dead centre? Two reasons. There is only a short distance left for the piston to travel, and by then the expanded, cooled gas has relatively little pressure left to give. In return, the gas blows down, so by bottom dead centre there is no back pressure resisting the piston as it rises. On the exhaust stroke the piston pushes the rest of the gas out, and the exhaust valve is held open until after top dead centre so that the momentum of the moving gas can scavenge the cylinder as completely as possible. The graph shows the idea that makes all this work, the ineffective crank angle. In the first twenty degrees after top dead centre the piston moves only about four per cent of its stroke, while twenty degrees at mid-stroke move it about seventeen per cent. Around the dead centres, opening a valve early or late hardly changes the volume.
Part 2 · Practical timing
Valve lead, valve lag and valve overlap Valve lead : opening before the theoretical point: inlet before TDC, exhaust before BDCValve lag : closing after it: inlet after BDC, exhaust after TDCValve overlap : both valves open together, around TDC at the end of exhaust and start of induction , measured in crankshaft degrees Exhaust outflow lowers cylinder pressure, drawing in fresh mixture: better volumetric efficiency Valve timing is fixed by the cams: it does not change with RPM
TDC BDC IO 20° BTDC EC 15° ATDC IC 55° ABDC EO 55° BBDC spark 25° BTDC overlap 35° (IO 20 + EC 15) outer: inlet · inner: exhaust Typical figures; every engine has its own fixed timing
Chapter 2 · Piston Engine Construction and Operation
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three terms describe the practical timing, and you must define them exactly. Valve lead means a valve opens before its theoretical point: the inlet before top dead centre, the exhaust before bottom dead centre. Valve lag means a valve stays open after its theoretical closing point: the inlet after bottom dead centre, the exhaust after top dead centre. Valve overlap is the period when both valves are open together. It happens around top dead centre, between the end of the exhaust stroke and the start of induction, and it is measured in degrees of crankshaft rotation. Watch the scene stop at overlap with both valves just open. The outgoing exhaust gas lowers the pressure in the cylinder below manifold pressure, so fresh mixture starts flowing in and helps push out the last burnt gas, improving volumetric efficiency. The cams fix the timing, so lead, lag and overlap stay the same at every RPM.
Part 3 · Measuring the work
The indicator (P–V) diagram
TDC BDC 0 10 20 30 40 50 cylinder volume pressure (bar) IMEP ≈ 9 bar: same area as the loop combustion: pressure soars at almost constant volume compression power (expansion) Pumping loop (magnified) TDC BDC 0.8 1.0 1.2 volume bar exhaust stroke induction stroke negative work done BY the piston
The enclosed area is the work done in one cycle. IMEP is the steady pressure that would do the same net work over one stroke.
Chapter 2 · Piston Engine Construction and Operation
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Engineers measure what happens inside the cylinder with an indicator, a pressure transmitter screwed into the combustion chamber like a spark plug, which traces cylinder pressure against piston position. The result is the indicator diagram, or P V diagram. On the left you see compression rising from bottom to top dead centre, the near-vertical rise of combustion at almost constant volume, and the expansion curve of the power stroke falling away. The area enclosed by the loop represents the work done on the piston in one cycle. On the right is the small pumping loop of the exhaust and induction strokes, magnified, which is work done by the piston against back pressure and suction, so it is subtracted. If you averaged all of this into one steady pressure acting on the piston for one stroke, giving the same net work, you would have the indicated mean effective pressure, I M E P, here about nine bar.
Part 3 · Measuring the work
IMEP, manifold pressure and horsepower IMEP : the average effective pressure on the piston over the working cycleThe pilot sees manifold absolute pressure (MAP), in inches of mercury , as a guide to cylinder pressure Power is controlled by the throttle , which varies the quantity of air ; open it and MAP rises IHP = P L A N E ÷ 33 000 : more pressure, longer stroke, bigger bore, more cylinders or more RPM give more powerBHP = IHP − FHP (friction horsepower): the useful power at the propeller
10 15 20 25 30 35 MAP in Hg Manifold absolute pressure gauge throttle open → MAP ↑ throttle closed → MAP ↓ engine stopped: reads ambient pressure IHP = P × L × A × N × E ÷ 33 000 P = IMEP 180 psi · L = 0.365 ft (4.375 in stroke) A = 20.6 in² (5.125 in bore) · N = 4 · E = 2700 ÷ 2 = 1350 IHP = 222 · at 82 % mechanical efficiency, BHP ≈ 182
Chapter 2 · Piston Engine Construction and Operation
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The pilot has no IMEP gauge, but the manifold absolute pressure gauge, calibrated in inches of mercury, shows the pressure of the charge going into the cylinders, which is a good guide to cylinder pressure. Power in a piston engine is controlled by the throttle, which varies the quantity of air entering the cylinders: opening it raises manifold pressure, closing it lowers it. From IMEP we can calculate the indicated horsepower with the PLANE formula: pressure, times stroke length in feet, times piston area, times number of cylinders, times effective working strokes per minute, all divided by thirty-three thousand. For a four-stroke engine the working strokes per cylinder are half the RPM. Our example gives about two hundred and twenty indicated horsepower. Some of that is used to turn the engine itself, the friction horsepower. What is left at the propeller is the brake horsepower, here about one hundred and eighty.
Part 3 · Efficiency
Specific fuel consumption and the three efficiencies
Fuel energy 100 % Indicated power (IHP) 30.5 % Brake power (BHP) 25 % − friction power (FHP) mechanical efficiency = 25 ÷ 30.5 ≈ 82 % thermal efficiency (brake) ≈ 25 %
Specific fuel consumption lb of fuel per BHP per hour . 135 BHP for 60 lb/h = 0.44. Less fuel for the same power is a decrease (better). Hot air increases SFC.
Mechanical efficiency BHP ÷ IHP , typically 80–85 % . Friction is the loss.
Thermal efficiency Heat turned into work ÷ heat in the fuel: about 25–28 % . Raised by a higher compression ratio and the right fuel.
Volumetric efficiency Weight of charge induced ÷ weight that would fill the cylinder at normal temperature and pressure: 75–85 % when normally aspirated (not supercharged).
Chapter 2 · Piston Engine Construction and Operation
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the four performance measures. Specific fuel consumption is the weight of fuel burned per brake horsepower per hour; in our example, one hundred and thirty-five horsepower for sixty pounds an hour is zero point four four. Less fuel for the same power is a decrease in S F C, an improvement; on a hot day the thin air gives less power, so S F C increases. Mechanical efficiency is brake horsepower divided by indicated, typically eighty to eighty-five per cent. Thermal efficiency compares the heat turned into work with the heat in the fuel, only about twenty-five to twenty-eight per cent. Volumetric efficiency compares the weight of charge actually induced with the weight that would fill the cylinder at normal temperature and pressure; it is seventy-five to eighty-five per cent in a normally aspirated, meaning unsupercharged, engine. Engine power is proportional to the weight of mixture induced. Exhaust back pressure falls as you climb, which slightly slows the loss of power.
Part 3 · Compression ratio
Swept, clearance and total volume Swept volume = piston (bore) area × stroke: the volume displaced in one strokeClearance volume : the space above the piston at TDC, the combustion chamberTotal volume = swept + clearance (piston at BDC)Compression ratio = total volume ÷ clearance volume Engine total volume = CR × clearance volume × number of cylinders
piston at TDC piston at BDC clearance volume the combustion chamber total volume swept + clearance CR = total ÷ clearance = (1 300 + 200) ÷ 200 = 7.5 : 1
Chapter 2 · Piston Engine Construction and Operation
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three volumes matter. The swept volume is the volume the piston displaces in one stroke: the area of the bore times the stroke. The clearance volume is the space left above the piston crown at top dead centre; it forms the combustion chamber. The total volume, with the piston at bottom dead centre, is the swept volume plus the clearance volume. The compression ratio is the total volume divided by the clearance volume. For example, with a swept volume of thirteen hundred cubic centimetres and a clearance volume of two hundred, the total is fifteen hundred, so the compression ratio is fifteen hundred divided by two hundred, seven and a half to one. Work backwards too. If the total volume is two and a half litres and the swept volume two litres, the clearance volume is half a litre and the ratio is five to one. And since total equals ratio times clearance, an engine's total volume is the compression ratio times the clearance volume times the number of cylinders.
Part 3 · Compression ratio
Why compression ratio matters Higher CR → better use of the fuel: higher thermal efficiency Higher CR → higher mean effective pressure and power from the same size But higher working pressures put higher loads on the moving parts And it needs fuel of the correct grade to avoid detonation Worked: total 9 600 cc in 4 cylinders, bore area 100 cm², throw 10 cm → 6 : 1
4 6 8 10 12 14 30 % 40 % 50 % 60 % 70 % compression ratio ideal thermal efficiency 6 : 1 → 51 % 7.5 : 1 → 55 % 9 : 1 → 58 % gains get smaller as the ratio rises Ideal (air-standard) efficiency = 1 − 1 ÷ CR^0.4 Real engines reach about half these values, but the trend is the same
Chapter 2 · Piston Engine Construction and Operation
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why do designers care so much about compression ratio? Because a higher ratio makes better use of the fuel. The gas is expanded further on the power stroke, more of its heat becomes work, and the thermal efficiency rises, as the graph shows; the gains are large at low ratios and get smaller as the ratio rises. A higher ratio also gives a higher mean effective pressure, so more power from the same size of engine. The price is higher working pressures and loads on the moving parts, and the need for fuel of the correct grade, because a high ratio makes the mixture more likely to detonate. Now a classic exam calculation. An engine has four cylinders and a total volume of nine thousand six hundred cubic centimetres, so two thousand four hundred per cylinder. The bore area is one hundred square centimetres and the crank throw ten centimetres, so the stroke is twenty. Swept volume is two thousand, clearance four hundred, and the ratio six to one.
Part 3 · Gas behaviour
Gas behaviour in the cylinder: exam reminders Halve the volume at constant temperature and the pressure doubles (Boyle) On compression the mass of the charge stays constant ; volume falls, pressure and temperature rise On induction the charge temperature falls as fuel evaporates Convergent duct (subsonic): velocity up, pressure and temperature down Divergent duct : velocity down, pressure and temperature up
Boyle Halve the volume at constant temperature → pressure doubles Compression stroke Mass of charge constant; V ↓, p ↑, T ↑ (adiabatic heating) Induction stroke Temperature falls: fuel evaporates and the charge expands Convergent duct V ↑ p ↓ T ↓ (subsonic) Divergent duct V ↓ p ↑ T ↑ (subsonic)
Chapter 2 · Piston Engine Construction and Operation
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Several end of chapter questions test the gas behaviour from chapter one in an engine setting, so here are the reminders in one place. If the volume of a gas is halved at constant temperature, its pressure is doubled; that is Boyle's law. During the compression stroke both valves are shut, so the mass of mixture in the cylinder stays constant, while its volume falls and its pressure and temperature rise. During the induction stroke the temperature of the charge falls, because the fuel evaporates and takes heat from the air. And remember the duct trends for subsonic flow. In a convergent duct the velocity increases while the pressure and the temperature decrease. In a divergent duct the velocity decreases while the pressure and the temperature increase. Be careful: some question banks print a convergent duct answer with pressure and velocity both increasing. That cannot be right, because Bernoulli says that when velocity goes up, static pressure comes down.
Part 4 · Construction
Crankcase and crankshaft Crankcase : two light-alloy halves; holds the main bearings, supports the cylinders, seals in the oil; a breather vent stops pressure building upCrankshaft : converts the pistons' straight-line motion into rotation , drives the propeller and accessories; its throw sets the strokeMain journals in plain main bearings; crankpins carry the rods; oilways drilled through it (also feed a variable-pitch propeller) Balanced and counterweighted ; kept short and well supported against torsional vibration Critical RPM : a band to avoid, shown by a red arc on the RPM indicator
prop main journal in a plain main bearing crankpin carries the big end web counterweight drilled oilway oil to the crankpin bearing shells Four throws for four cylinders: 1 and 4 up, 2 and 3 down Short, well supported and counterweighted against torsional vibration Critical RPM band: red arc on the tachometer: do not dwell there Crankcase: two light-alloy halves holding the main bearings, vented by a breather to stop pressure building up
Chapter 2 · Piston Engine Construction and Operation
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The crankcase is usually made of light alloy in two halves, so the crankshaft can be fitted and removed. It houses the main bearings, supports the cylinders, provides the engine mountings and forms a sealed chamber for the oil. A breather vents it to atmosphere so that gas leaking past the pistons cannot build up pressure inside. The crankshaft is the part that converts the straight-line motion of the pistons into rotation; it drives the propeller and the accessories, and the offset of its throws sets the stroke. The main journals run in plain main bearings, which can carry the heavy reciprocating loads, and oilways drilled through the shaft carry oil to the bearings and, on some engines, to a variable-pitch propeller. Each power impulse twists the shaft slightly, and at certain speeds the impulses can match its natural frequency and cause rough running. That band, the critical RPM, is marked by a red arc on the RPM indicator.
Part 4 · Construction
Firing interval and firing order Firing interval = 720° ÷ number of cylinders : 4 cyl 180°, 6 cyl 120°, 9 cyl 80°Four cylinders are the minimum for a reasonably smooth firing interval A full cycle is always 720° , however many cylinders Cylinders do not fire one after the next: that would load the crankshaft unevenly. In-line four: 1-3-4-2 ; Lycoming: 1-3-2-4 Each cylinder in the firing order runs one stroke behind the one before it
Firing interval = 720° ÷ number of cylinders 4 cylinders 180° 6 cylinders 120° 7 cylinders ≈ 103° 9 cylinders 80° Firing order 1-3-4-2: each cylinder runs one stroke behind the cylinder that fired before it 0–180° 180–360° 360–540° 540–720° Cyl 1 Power Exhaust Induction Compression Cyl 2 Exhaust Induction Compression Power Cyl 3 Compression Power Exhaust Induction Cyl 4 Induction Compression Power Exhaust At every moment the four cylinders are on four different strokes Lycoming flat-four: 1-3-2-4
Chapter 2 · Piston Engine Construction and Operation
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
With more cylinders there are more power strokes in the seven hundred and twenty degrees of a cycle, so the engine runs more smoothly. The angle between power strokes is the firing interval: seven hundred and twenty divided by the number of cylinders. A four gives one hundred and eighty degrees, a six one hundred and twenty, and a nine-cylinder radial eighty. Four cylinders are generally regarded as the minimum for a reasonable firing interval. The cycle itself is always seven hundred and twenty degrees, however many cylinders there are. The order in which the cylinders fire is the firing order. Firing them one after the next would load the crankshaft and cause vibration, so a typical in-line four fires one, three, four, two, and a Lycoming flat four fires one, three, two, four. Look at the table. Each cylinder runs one stroke behind the one that fired before it, so at any instant all four strokes are under way.
Part 4 · Construction
Pistons, rings and connecting rods Piston : aluminium alloy sliding plug; bosses carry the gudgeon pin to the rod's small end Compression rings (top) stop gas leaking down; gas pressure pushes them down and out against the wallOil control (scraper) rings spread oil and stop excess oil reaching the chamberRings are cast iron : springy when hot, and self-lubricating (graphite); worn or stuck rings → blue smoke Connecting rod : H-section high-tensile steel; big end on the crankpin. Crank system = pistons, gudgeon pins, rods, crankshaft
compression rings cast iron; seal gas oil control (scraper) ring spreads oil, stops excess gudgeon pin in the piston bosses connecting rod H-section high-tensile steel big end on the crankpin piston: aluminium alloy small end on the pin
Chapter 2 · Piston Engine Construction and Operation
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The piston is an aluminium alloy plug that slides in the cylinder and passes the force of the expanding gas, through the connecting rod, to the crankshaft. Bosses inside it carry the gudgeon pin, which joins it to the small end of the rod. Grooves round the piston hold the rings. The compression rings at the top stop gas leaking down into the crankcase; gas pressure pushes each ring down in its groove and out against the cylinder wall, and a second, sometimes third, ring catches what gets past. Below them, the oil control or scraper ring spreads oil evenly and stops too much reaching the combustion chamber. Rings are made of cast iron, which stays springy when hot and is self-lubricating thanks to its graphite. Worn or stuck rings let oil burn, giving blue exhaust smoke. The rod is H-section steel. Pistons, gudgeon pins, rods and crankshaft together make up the crank system.
Part 4 · Construction
Cylinders, heads and valves Barrel : alloy steel, bolted to the crankcase; about 30 % of the combustion heat goes into it; fins (air) or jackets (liquid) remove itHead : aluminium alloy, usually screwed and shrunk on; carries valves, guides, plugs and rockersValve seats cut at 30° or 45° ; faces lapped for a gas-tight seal; guides keep valves straightExhaust valve stems may be hollow and part sodium-filled for cooling Valve springs close the valve ; two per valve, one inside the other: a safety factor and less valve bounce
sodium-filled exhaust valve stem two springs one inside the other valve seat 30° or 45° valve guide inlet valve cylinder barrel: alloy steel fins carry heat to the air head: Al alloy ≈ 30 % of the heat of combustion goes into the cylinder
Chapter 2 · Piston Engine Construction and Operation
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
The cylinder barrel is made of alloy steel to resist combustion pressure and give the piston a hard working surface, and it is held to the crankcase by studs and nuts. About thirty per cent of the heat of combustion goes into the cylinder, so it needs cooling: fins on air-cooled engines, a liquid jacket on liquid-cooled ones. The head, of aluminium alloy for good heat transfer, is usually screwed and shrunk onto the barrel. It carries the valves, valve guides, spark plugs and rockers. Valve seats are cut at thirty or forty-five degrees, and each valve face is ground to match and lapped in to seal. Exhaust valves run very hot, so their stems are sometimes hollow and part-filled with sodium, which melts and carries heat up to the cooler stem. It is the valve springs that close the valves; the cams only open them. Two springs, one inside the other, give a safety factor and help prevent valve bounce.
Part 4 · Construction
Valve operating gear Camshaft driven from the crankshaft at half crankshaft speed , whatever the number or layout of cylindersOne cam lobe for each valve; each valve opens once per cycle (two crank turns) Lobe positions are fixed, so lead, lag and overlap are constant at all RPM Timing angles are quoted in crankshaft degrees, not camshaft degrees Cam → (tappet and push rod on most flat engines) → rocker → valve; the spring closes it
cam lobe one per valve rocker camshaft ½ crank speed crank: 2 turns camshaft: 1 turn each valve opens once
Chapter 2 · Piston Engine Construction and Operation
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
The valves are opened by the valve operating gear. A camshaft, driven by gears from the crankshaft, carries one cam lobe for each valve. As the lobe comes round it pushes the valve open, through a rocker in this overhead layout, or through a tappet, push rod and rocker on most horizontally opposed engines. The spring then closes the valve as the lobe passes. Each valve has to open only once per cycle, which is once every two turns of the crankshaft, so the camshaft is driven at half crankshaft speed, whatever the number of cylinders or their layout. Watch the camshafts in the scene turning slowly compared with the crank. Because the lobes are fixed on the shaft, the valve lead, lag and overlap stay the same at every engine speed. And because the camshaft is driven by the crankshaft, all valve timing figures are quoted in degrees of crankshaft rotation, never camshaft rotation.
Part 4 · Construction
Valve (tappet) clearance A small gap between the rocker pad and the valve tip , so the valve can close fully The valve heats and expands more than the rest of the gear; the gap shrinks but the valve still seats Measured with feeler gauges ; adjusted on the rocker Too much : valve opens late and closes early (and is noisy)Too little : opens early , closes late , may not close at all: an inlet valve held open gives popping back . Hydraulic tappets run with zero clearance
Cold engine gap set gap with feeler gauge valve stem rocker Hot engine gap valve grew: gap smaller valve stem rocker Measured between the rocker pad and the valve tip Too big: opens late, closes early · Too small: opens early, closes late
Chapter 2 · Piston Engine Construction and Operation
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
To be sure the valves close fully, a small gap is left between the rocker pad and the tip of the valve stem when the valve is shut. This is the valve, or tappet, clearance. The valves are heated directly by combustion and expand more than the rest of the operating gear, so as the engine warms up the gap gets smaller, but the valve still closes. It is measured with feeler gauges and adjusted on the rocker. If the clearance is too big, the rocker has to take up the extra gap before it touches the valve, so the valve opens late and closes early. If it is too small, the valve opens early and closes late, and when hot it may not close at all. An inlet valve that does not seat lets burning mixture flash back into the induction system, called popping back; a sticking inlet valve does the same. Hydraulic tappets, lengthened by oil pressure, run with no clearance and need no adjustment.
Part 4 · Construction
Sump, induction, exhaust and accessory drives Sump Bolted under the crankcase; collects the oil, and in a wet-sump engine is the oil reservoir; a filter protects the pumps.
Carburettor or injector Meters the air and adds the right fuel at every altitude and attitude; feeds the cylinders through the induction manifold .
Exhaust system Steel pipes from each cylinder, joined into one or two, take the hot gas overboard.
Accessory housing (wheelcase) At the rear, gear-driven by the crankshaft: oil and fuel pumps, magnetos , supercharger, starter , generator, hydraulic and vacuum pumps.
Reduction gear Between the crankshaft and propeller (spur or planetary): engine fast, propeller slow. Low-power engines are direct drive .
Operating notes Starter engaged light on after start: shut down immediately . Long periods at low RPM foul the spark plugs .
Chapter 2 · Piston Engine Construction and Operation
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The sump is a casing under the crankcase that collects the oil after it has passed through the engine; in a wet-sump engine it is the oil reservoir, with a filter to protect the pumps. The carburettor, or a fuel injector, meters the air entering the engine and adds the right amount of fuel at every altitude and attitude, and the induction manifold carries the charge to the cylinders. The exhaust system takes the hot gas overboard. At the back of the engine the accessory housing, or wheelcase, carries gears driven by the crankshaft for the oil and fuel pumps, magnetos, supercharger and starter, and for aircraft services such as the generator and hydraulic pump. Some engines have a reduction gear between the crankshaft and the propeller, so the engine can run fast for power while the propeller turns slowly for efficiency. Two operating points: if the starter engaged light stays on after start, shut down at once, and avoid long periods at low RPM, which foul the plugs.
Part 4 · Construction
Reading an engine designation Engines are classified by layout, drive, rotation, capacity, cooling, fuel system and aspiration, and the model number says much of it. Example: Lycoming AEIO-540-L1B5 .
Letters / numbers Meaning Other common letters AE Aerobatic engine (oil and fuel systems work inverted) — I Fuel injected no letter: carburettor O Horizontally opposed cylinders R: radial 540 Displacement 540 cubic inches O-320, O-360: 320, 360 in³ L Left-hand (counter-) rotationno letter: normal rotation 1B5 Variant: modifications from the basic model — G, S, T Geared, supercharged, turbocharged (e.g. GSO, TIO) —
Chapter 2 · Piston Engine Construction and Operation
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aero engines are classified by cylinder arrangement, type of drive, direction of rotation, cylinder capacity, cooling, fuel system, and whether they are supercharged or normally aspirated, and most manufacturers pack much of that into the model number. Take the Lycoming A E I O five forty L one B five. A E means aerobatic engine, with oil and fuel systems that keep working upside down. I means fuel injected; with no I it would have a carburettor. O means horizontally opposed cylinders. Five forty is the displacement, five hundred and forty cubic inches. L means left-hand rotation, the opposite way to normal, used for example on one engine of a twin. One B five identifies the modifications from the basic model. Other letters you will see are G for geared, meaning a reduction gearbox, S for supercharged and T for turbocharged, as in the T I O five forty.
Summary
What to take into the exam Layouts In-line (≤6 air-cooled, often inverted), vee 8–12 liquid, radial odd per row, flat 4 or 6. Interval = 720° ÷ cylinders.
Cycle I, C, P, E: four strokes, five events, 720°. Combustion at constant volume. Only the power stroke drives.
Timing IO before TDC, IC after BDC, EO before BDC, EC after TDC. Overlap at TDC, crank degrees, fixed with RPM.
Power IHP = PLANE ÷ 33 000; BHP = IHP − FHP. SFC = lb per BHP per hour.
Efficiencies Mechanical 80–85 %, thermal 25–28 %, volumetric 75–85 % (by weight of charge).
Compression ratio CR = total ÷ clearance; swept = area × stroke; stroke = 2 × throw. Higher CR → higher thermal efficiency.
Parts Cast-iron rings (self-lubricating); worn → blue smoke. Two springs: less bounce. Sodium exhaust valves.
Valve gear Camshaft ½ crank speed. Clearance rocker pad–valve tip: too big late/early, too small early/late.
Chapter 2 · Piston Engine Construction and Operation
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. In-line engines are limited to about six air-cooled cylinders and are often inverted; vees have eight to twelve liquid-cooled cylinders; radials have an odd number per row; and flat fours and sixes power most light aircraft. The firing interval is seven hundred and twenty degrees divided by the number of cylinders. The cycle is induction, compression, power, exhaust: four strokes, five events, two turns, with combustion at constant volume. The inlet opens before top dead centre and closes after bottom; the exhaust opens before bottom and closes after top; overlap is around top dead centre, measured in crank degrees and fixed at all speeds. Indicated horsepower is PLANE over thirty-three thousand, and brake is indicated minus friction. Compression ratio is total over clearance volume. Rings are cast iron; two springs reduce bounce. The camshaft turns at half crankshaft speed, and too much clearance makes valves open late and close early.