Engines · Chapter 11
Piston Engine Performance, Supercharging and Turbocharging Why a piston engine loses power as it climbs, and how turbochargers and internal superchargers win it back: boost and MAP, waste gates and controllers, critical altitude and full throttle height.
boosted air to the engine air in exhaust out exhaust from the engine waste gate
COMPRESSOR TURBINE
one shaft
normally aspirated turbocharged internally supercharged
power against altitude, 0 to 25 000 ft
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to chapter eleven, on piston engine performance and power augmentation. A piston engine makes its power from the mass of air and fuel it burns, so as an aircraft climbs into thinner air, a plain engine steadily loses power. In this lesson we see exactly why that happens, how density altitude captures it, and then how engineers fight back: by compressing the air before it reaches the cylinders. We will meet the two great families, the exhaust-driven turbocharger with its waste gate, and the gear-driven internal supercharger with its automatic boost control. Along the way you will learn to read boost and manifold pressure gauges, and to tell critical altitude from full throttle height, which examiners love to test.
Roadmap
From thin air to boosted power 1 · Power and the air Mass of charge, the standard day, density altitude , and why a plain engine fades as it climbs.
2 · Supercharging Why we boost, ground- and altitude-boosted, the centrifugal compressor , heat and the intercooler.
3 · Measuring it Boost in psi and MAP in inches of mercury, and how to convert.
4 · Turbochargers Exhaust turbine, waste gate , actuator and controllers, critical altitude , handling and failures.
5 · Internal superchargers Gear drive, the automatic boost control , full throttle height and rated altitude.
6 · Comparison and checks Turbo against supercharger in the climb, static boost and reference RPM .
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through this chapter. We start with the air itself: why the power of a piston engine depends on the mass of charge it burns, what the standard day is, and how density altitude tells you what the engine really feels. Then we look at supercharging in general, and at the centrifugal compressor that does the work. Next, the two gauges that measure the result, boost and manifold absolute pressure. Part four is the turbocharger, driven by exhaust gas, with its waste gate, its controllers and its critical altitude. Part five is the internal, gear-driven supercharger, with the automatic boost control and full throttle height. Finally we compare the two systems in the climb, and finish with the static boost and reference RPM power check.
Part 1 · Power and the air
Power comes from the mass of charge Power depends on the mass (weight) of mixture burnt each second Mass in each cylinder = volume × density of the charge in the manifold Density rises with pressure and falls with temperature Volumetric efficiency : charge actually induced ÷ swept volume (at ambient conditions); usually below 100%Raise the manifold pressure and you pack in more charge: the idea behind supercharging
inlet valve closing
CHARGE
piston near BDC
mass = volume × density
pressure ↑ density ↑ temperature ↑ density ↓
More mass of charge burnt each second = more power
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Everything in this chapter grows from one simple fact: a piston engine makes power by burning fuel and air, and the more mass of charge it burns each second, the more power it makes. On each induction stroke the piston sweeps a fixed volume, and the inlet valve closes with a certain amount of charge trapped inside. The mass of that charge is its volume times its density, and the density depends on the pressure and temperature in the induction manifold. Higher pressure packs the molecules closer; higher temperature spreads them out. Volumetric efficiency compares the charge actually drawn in with the swept volume at outside conditions, and in a plain engine it is below one hundred per cent. So if we can raise the manifold pressure artificially, we can cram in more charge and get more power. That is supercharging.
Part 1 · Power and the air
The standard day, and how the air thins ISA sea level: +15 °C , 1013.25 hPa = 29.92 inHg = 14.7 psi , density 1.225 kg/m³ Pressure comes from the weight of air above ; it falls about 1 inHg per 1000 ft low down Temperature falls about 2 °C per 1000 ft : the air is warmed from the ground Density falls too, but a little slower than pressure , because the air is also colder Engine makers quote power for the ISA sea-level standard day , so it can be checked anywhere
0
5
10
15
20
25
40%
50%
60%
70%
80%
90%
100%
Altitude (thousands of feet, ISA)
Fraction of the sea-level value
density 74%
pressure 69%
temperature (K)
density
pressure
ISA sea level: 15 °C · 1013.25 hPa · 29.92 inHg · 14.7 psi · 1.225 kg/m³
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
To compare engines anywhere in the world we need a standard day, and that is the International Standard Atmosphere. At mean sea level it gives a temperature of plus fifteen degrees Celsius, a pressure of one thousand and thirteen point two five hectopascals, which is twenty-nine point nine two inches of mercury or fourteen point seven pounds per square inch, and a density of one point two two five kilograms per cubic metre. Pressure is simply the weight of the air above us, so it falls as we climb, about one inch of mercury per thousand feet near the ground. Temperature falls too, about two degrees per thousand feet. Density falls a little more slowly than pressure, because the colder air partly makes up for it. At ten thousand feet you still have about seventy-four per cent of sea-level density. Manufacturers quote their power figures for this standard sea-level day.
Part 1 · Power and the air
Density altitude: what the engine feels Density altitude : the height in the ISA at which today’s density would be foundEngine, propeller and wing performance all follow density altitude , not elevation Quick rule: add 118 ft for every °C above ISA to the pressure altitude Or use the flight computer (airspeed window) or a chart for an exact figure Hot and high aerodromes give a high density altitude: less power, longer take-off
Example 1
0
4k
8k
12k
16k
pressure alt 5,500 ft
density alt ≈ 9,000 ft
ISA at 5 500 ft ≈ +4 °C; OAT +34 °C
ISA + 30 → 30 × 118 = 3 540 ft
Elevation 5 500 ft, QNH 1013
Example 2: Leh
0
4k
8k
12k
16k
pressure alt 10,682 ft
density alt ≈ 14,300 ft
ISA at 10 682 ft ≈ −6 °C; OAT +25 °C
ISA + 31 → 31 × 118 ≈ 3 660 ft
Elevation 10 682 ft, QNH 1013
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Density altitude is the height in the standard atmosphere at which you would find today’s air density. It is what the engine actually feels, so performance figures are tied to it. The quick rule is to start from pressure altitude and add one hundred and eighteen feet for every degree that the temperature is above standard. Take an aerodrome at five thousand five hundred feet with Q N H one thousand and thirteen, on a day of I S A plus thirty. Standard temperature there is about plus four, so it is plus thirty-four. Thirty times one hundred and eighteen is about three thousand five hundred feet, so the density altitude is close to nine thousand feet. A summer day at Leh, at nearly ten thousand seven hundred feet and twenty-five degrees, gives over fourteen thousand feet. The flight computer gives a slightly more exact answer, but the rule is close enough for the exam.
Part 1 · Power and the air
A normally aspirated engine in the climb At full throttle the MAP is a little below ambient (intake losses), and it falls about 1 inHg per 1000 ft at constant RPM Less dense charge, so power falls steadily with height A small help: lower exhaust back pressure improves scavenging Power available changes because of decreasing density and decreasing back pressure At a fixed throttle in full rich , the mixture gets richer as the air thins, so CHT decreases
0
5
10
15
20
10
15
20
25
30
Full-throttle MAP (inHg)
ambient pressure
MAP, a little below ambient
0
5
10
15
20
40
60
80
100
Altitude (thousands of feet)
Power (% of sea-level power)
84%
24
70%
20
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now let us climb with a normally aspirated engine, one with no supercharging at all. At full throttle the manifold pressure is always a little below the outside pressure, because the air loses some pressure through the filter, the carburettor and the ducting. As we climb at constant RPM the manifold pressure falls, roughly one inch per thousand feet, and with less dense charge the power falls with it: about eighty-four per cent at five thousand feet and seventy per cent at ten thousand. There is one small consolation. The outside pressure that the exhaust has to push against also falls, so the cylinders scavenge a little better. And if you keep the throttle fixed and the mixture in full rich, the fuel flow stays much the same while the air gets thinner, so the mixture becomes richer, the engine runs cooler, and the cylinder head temperature decreases. That is why we lean in the climb.
Part 2 · Supercharging
Why supercharge, and how far? Supercharging: raising manifold pressure artificially to increase the mass of charge It raises volumetric efficiency , even above 100%; the engine’s own compression ratio is unchanged Ground-boosted : more than sea-level power for take-off; the engine must be strengthened Altitude-boosted : holds sea-level pressure up to height; needs a control to prevent overboost low downThe limit is detonation (and mechanical stress): boost limits keep a safe margin
NA, sea level
100%
NA, 10 000 ft
74%
Altitude-boosted
10 000 ft
100%
Ground-boosted
sea level
130%
Mass of charge in the cylinder (numbers of dots to scale)
Limit: detonation and the mechanical strength of the engine
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why supercharge? The primary purpose is to increase the mass of charge entering the cylinders, by raising the manifold pressure above what the atmosphere alone would give. That raises the volumetric efficiency, which can then go above one hundred per cent. Notice that the engine’s compression ratio does not change; that is fixed by the cylinder geometry. There are two aims. A ground-boosted engine uses the extra pressure to give more than its sea-level power for take-off and initial climb, so the engine must be built stronger to take the higher cylinder pressures. An altitude-boosted engine uses it to hold sea-level manifold pressure up to a great height; low down the compressor could produce far too much pressure, so it needs a control system. Either way, the limit to how much supercharging an engine can take is detonation, along with mechanical stress, and the boost limits keep a safe margin from it.
Part 2 · Supercharging
Two families: turbocharger and internal supercharger
Turbocharger (externally driven)
Compressor
Carburettor and throttle
Engine
Turbine
common shaft
waste gate (turbine bypass)
air
overboard
Internal supercharger (gear-driven)
Carburettor and throttle
Impeller
Engine
Gears 6–12 : 1 from the crankshaft
air
mixture
exhaust overboard
Compresses AIR · upstream of the throttle
driven by exhaust energy that would otherwise be wasted
Compresses MIXTURE · downstream of the throttle
driven by the crankshaft through gears
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two families of supercharger, and you must keep them apart. On the left is the externally driven type, the turbocharger or turbo-supercharger. A turbine in the exhaust drives a compressor on the same shaft, using exhaust energy that would otherwise be wasted. Its compressor sits upstream of the carburettor and throttle, so it compresses air only. On the right is the internally driven supercharger. Its impeller is geared to the crankshaft, and it sits downstream of the throttle, so it compresses the fuel and air mixture. Both use centrifugal compressors. Remember the two pairs: turbocharger, upstream, air; internal supercharger, downstream, mixture. Their control systems, and the way they behave in the climb, are quite different, so we take them one at a time.
Part 2 · Supercharging
The centrifugal compressor Chosen because it is light, robust, reliable , runs fast and handles large airflows Air enters at the eye and is flung out to the tip by the impeller : velocity rises, and some pressure The diffuser : fixed vanes forming divergent passages ; velocity falls, pressure rises Energy: mechanical → kinetic in the impeller, kinetic → pressure in the diffuser Pressure ratio set by impeller diameter, speed and vane shape : up to about 3 : 1 ; more needs two stages
rotation
Eye
air enters here
Impeller vanes
fling the air outwards
Diffuser vanes
divergent passages
Orange track
path of the air
impeller: eye → tip diffuser → manifold
velocity
pressure
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Both families use the centrifugal compressor, because it is light, robust and reliable, it can spin very fast, and it handles a large flow of air. It has two parts. The impeller turns, drawing air in at its centre, the eye, and flinging it outwards between its vanes to the tip. That gives the air a lot of kinetic energy, and because the passage widens, some pressure too. The air leaves the tip fast, with both tangential and radial velocity, and enters the diffuser, a ring of fixed vanes forming divergent passages. There the velocity falls and the pressure rises: kinetic energy is converted into pressure energy. How much pressure rise you get depends on the impeller’s diameter, its speed and the shape of its vanes. About three to one is the practical limit for one stage; for more, two compressors are fitted in series.
Part 2 · Supercharging
Heat of compression and the intercooler Compressing air heats it ; hot air is less dense, so part of the gain is lost A hot charge also moves the engine closer to detonation Intercooler : a heat exchanger between the compressor and the inlet valves ; restores density, cuts detonation riskInternal superchargers: fuel sprayed into the eye of the impeller cools the charge as it evaporates Turbocharged diesels use intercoolers for the same reason Compressor
Intercooler air-to-air
Inlet valves
105 °C
50 °C
cooling air
×0
×0.5
×1
×1.5
×2
Charge density, relative to the air going in
×1.00
Air in, 15 °C
×2.00
Ideal 2 : 1,
no heating
×1.52
After compressor
105 °C
×1.78
After intercooler
50 °C
Pressure ratio 2 : 1, compressor 70 % efficient, intake 15 °C
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Compressing air always heats it, and that costs us. Take a compressor working at a pressure ratio of two to one on a fifteen degree day. If the air stayed cool its density would double. In practice it leaves at around one hundred and five degrees, so the density rises only about one and a half times. The hot charge also brings the engine closer to detonation. The cure is an intercooler, a heat exchanger placed between the compressor and the inlet valves, usually cooled by ram air. Cooling the charge back to, say, fifty degrees restores the density to about one point eight times, and the main benefit for the exam is that it minimises the risk of detonation. In an internal supercharger, spraying the fuel into the eye of the impeller helps in another way: the fuel evaporates and takes heat out of the charge.
Part 3 · Measuring it
Boost gauge and MAP gauge Manifold pressure : the pressure between the throttle valve and the inlet valve Boost gauge (British): psi above or below ISA sea-level pressure ; 14.7 psi reads zero MAP gauge (American): absolute pressure in inches of mercury ; zero boost = 29.92 inHg Rule of thumb: 2 inHg ≈ 1 psi of boost Boosted engines have a constant-speed propeller : RPM lever sets RPM, throttle sets manifold pressure
-10
-5
0
+5
+10
+15
BOOST
psi
10
20
30
40
50
MAP
inHg
+4 psi boost
≈ 38 inHg absolute
zero = 14.7 psi (ISA MSL)
29.92 = zero boost
14.7 + 4 = 18.7 psi absolute
rule of thumb: 2 inHg ≈ 1 psi
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
How does the pilot know how much charge is going in? We measure the manifold pressure, the pressure between the throttle valve and the inlet valve, and there are two ways to show it. The British boost gauge reads in pounds per square inch above or below standard sea-level pressure, so fourteen point seven psi reads zero. The American manifold absolute pressure gauge reads the absolute pressure in inches of mercury, so zero boost is twenty-nine point nine two inches. Watch both together. Engine stopped at sea level: zero boost and about thirty inches. At idle, with the throttle nearly shut, minus seven psi, about sixteen inches. Opened up and boosted, plus four psi, about thirty-eight inches. A handy rule is that two inches of mercury is about one psi. And because a boosted engine always has a constant-speed propeller, the RPM lever sets the RPM, and the throttle sets the manifold pressure.
Part 3 · Measuring it
Converting boost and MAP Absolute pressure = 14.7 psi + boost . Then multiply by about 2.04 (or simply 2) to get inches of mercury.
Boost gauge Absolute pressure MAP gauge Typical meaning −7 psi 7.7 psi ≈ 15.7 inHg Idling: throttle nearly closed −3 psi 11.7 psi ≈ 23.8 inHg Below standard: part throttle, or a plain engine at height 0 14.7 psi 29.92 inHg ISA sea-level pressure; the static reading at an ISA sea-level aerodrome +4 psi 18.7 psi ≈ 38 inHg Boosted above sea-level standard +10 psi 24.7 psi (≈ 25) ≈ 50 inHg A turbo held at +10 psi: the same anywhere below critical altitude
Trap: boost is measured from ISA mean sea-level pressure , not from today’s outside pressure. So +10 psi of boost always means about 25 psi absolute.
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us practise the conversion, because it turns up in the exam. Start with the boost reading, add fourteen point seven to get the absolute pressure in psi, then multiply by about two to get inches of mercury. Minus three psi of boost is eleven point seven psi absolute, about twenty-four inches. Plus four is eighteen point seven absolute, about thirty-eight inches. Plus ten is twenty-four point seven, call it twenty-five psi absolute, or about fifty inches. Now the trap. Boost is the manifold pressure minus I S A mean sea-level pressure. It is not measured from today’s outside pressure. So plus ten psi of boost means about twenty-five psi absolute wherever the aircraft is, and a turbocharged engine climbing below its critical altitude at plus ten psi still has about twenty-five psi in its manifold, even though the air outside is thinner.
Part 4 · Turbochargers
The turbocharger: exhaust turbine and compressor on one shaft
ENGINE cylinders
Compressor impeller
Turbine exhaust-driven
common shaft
air in
throttle
boosted air (deck pressure)
waste gate
exhaust overboard
exhaust
engine oil to the bearings
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a complete turbocharged installation. The engine’s exhaust, which would otherwise be thrown away, is led to the turbine. The gas passes through nozzles onto the turbine wheel’s vanes, spins it, and goes overboard. The turbine wheel and the compressor impeller are fixed to a common shaft, directly connected, with no gears or clutch between them, so they always turn together, at speeds up to about one hundred and ten thousand RPM. The compressor draws air from the filter, compresses it, and sends it on to the throttle and the engine. The shaft bearings are lubricated and cooled by the engine’s own oil. The turbocharger need not be part of the engine; it may sit on the engine or on the firewall, shielded from fuel and oil lines. And notice the waste gate, a valve that lets exhaust bypass the turbine. It is the key to controlling the whole system.
Part 4 · Turbochargers
The waste gate controls turbo speed A valve in the turbine bypass : an exhaust duct in parallel with the turbine Open : most exhaust goes straight overboard; the turbo slows down , less boostClosing : more exhaust through the turbine; the turbo speeds up , more boostFully shut : maximum turbo speed; this is reached at the critical altitude Turbo speed depends on engine RPM (exhaust flow) and waste gate position
Gate open: exhaust bypasses the turbine
Turbine
waste gate OPEN
exhaust in
turbine slow
low boost
Gate shut: all exhaust through the turbine
Turbine
waste gate SHUT
exhaust in
turbine fast
maximum boost
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The waste gate is how we control the turbocharger’s speed. It is a butterfly valve in an alternative exhaust duct, the turbine bypass, which runs in parallel with the turbine. Watch what happens when the gate is fully open. Most of the exhaust takes the easy way out, straight overboard, so the turbine and the compressor slow down and the boost falls. Now the gate swings shut. All of the exhaust is forced through the turbine, the turbocharger speeds up, and the compressor delivers more pressure. So opening the waste gate decelerates the turbocharger, and closing it accelerates it. The speed of the turbo therefore depends on two things: how much exhaust the engine makes, which goes with engine RPM and power, and where the waste gate is. When the gate is fully shut and the turbo can go no faster, the aircraft has reached its critical altitude.
Part 4 · Turbochargers
The actuator and the absolute pressure controller A single-acting actuator : the spring opens the gate, engine oil pressure closes it Its oil comes from the engine lubrication system, which also lubricates and cools the turbo bearings Absolute pressure controller (APC) : an aneroid capsule senses compressor outlet (deck) pressure Deck pressure low: capsule expands, bleed valve shuts , oil is trapped, the gate closes Deck pressure high: bleed opens , oil escapes to the sump, the spring opens the gate Oil supply lost: the spring drives the gate fully open , so boost is lost, not overdone
Waste gate actuator
spring: pushes the gate OPEN
engine oil: pushes it SHUT
waste gate
oil in
Absolute pressure controller
aneroid capsule senses deck pressure
bleed valve
to sump
from compressor outlet
deck low → bleed shut → gate closes
deck high → bleed open → gate opens
no oil → spring opens gate fully
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
How is the waste gate moved? In most systems it is linked to a single-acting actuator. A spring pushes the piston one way, opening the gate. Engine oil pressure pushes it the other way, closing the gate. The oil comes straight from the engine’s lubrication system, the same oil that lubricates and cools the turbocharger bearings. Oil flows into the actuator through a restrictor and leaves through a bleed valve, and the controller decides how much bleeds away. The simplest is the absolute pressure controller. Its aneroid capsule senses the compressor outlet pressure, often called deck pressure. If deck pressure is too low, the capsule expands, the bleed closes, oil is trapped, and the gate closes. If deck pressure is too high, the bleed opens, oil drains to the sump, and the spring opens the gate. And if oil pressure is lost, the spring drives the gate fully open: the engine loses its boost rather than being overboosted.
Part 4 · Turbochargers
The waste gate from start-up to critical altitude
1
Before start
OPEN
spring holds it open:
exhaust flows freely for
starting
2
Idle / low power
SHUT
too little exhaust:
capsule expands, bleed
shut, oil trapped
3
Full throttle, sea level
ALMOST OPEN
surplus exhaust: bleed
opens; margin for
high-pressure days
4
Climbing
CLOSING
inlet pressure falls:
bleed closes, gate
closes bit by bit
5
Critical altitude
FULLY SHUT
turbo at full speed;
above here MAP and power
fall
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow the waste gate through a whole flight with an absolute pressure controller. Before start there is no oil pressure, so the spring holds the gate fully open, letting the exhaust flow freely; otherwise the engine would be very hard to start. Just after start, at idle, there is far too little exhaust to make the required deck pressure, so the capsule expands, the bleed shuts, oil is trapped, and the gate closes fully. Now open up for take-off. There is plenty of exhaust, deck pressure tries to overshoot, the bleed opens, and at full throttle at sea level on a standard day the gate is almost fully open. That spare opening copes with days when the air pressure is higher than standard. As we climb, the inlet pressure falls, the bleed closes, and the gate closes bit by bit. Finally it is fully shut: that is the critical altitude.
Part 4 · Turbochargers
Critical altitude, and the power curve of a turbo engine Critical altitude : above it the selected MAP can no longer be held; the waste gate is fully shut Below it, MAP is held, but power still falls slowly : hotter charge and rising exhaust back pressure Above it, MAP and power fall faster , much like a normally aspirated engine Climbing at constant settings: CHT rises and volumetric efficiency falls The payoff: much better high-altitude performance and a higher service ceiling
0
5
10
15
20
25
10
20
30
Manifold pressure (inHg)
0
5
10
15
20
25
40
60
80
100
Altitude (thousands of feet)
Power (% of sea-level power)
critical altitude
(gate fully shut)
turbo: MAP held
normally aspirated
turbo: falls slowly
NA
then faster
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Critical altitude is the height above which the turbocharger can no longer maintain the selected manifold pressure, because the waste gate is already fully shut. Look at the graphs. Up to critical altitude the manifold pressure is held constant, but the power of a turbocharged engine still decreases a little with every foot of climb. Why? As the gate closes, more exhaust is forced through the turbine, so the exhaust back pressure on the engine rises; and the compressor works harder, so the charge gets hotter and less dense. The volumetric efficiency falls and the cylinder head temperature rises. Above critical altitude nothing more can be done, so manifold pressure and power fall away faster, roughly like a normally aspirated engine. Even so, the great advantage of the turbocharger is its high-altitude performance: far more power at height, and a much higher service ceiling.
Part 4 · Turbochargers
Other ways to control a turbocharger Control What it senses or does Notes Fixed orifice bypass No moving gate: a fixed share of exhaust always drives the turbo MAP set by the throttle only; rapid throttle movement easily overboosts Absolute pressure controller Aneroid senses deck pressure ; limits it to a set maximum Simple systems; the throttle then sets MAP Density controller Bellows of dry nitrogen sense deck pressure and temperature Limits maximum MAP at full throttle below critical altitude Differential pressure controller Senses the pressure drop across the throttle Works at every throttle position except fully open ; reduces bootstrapping Variable pressure controller A cam on the throttle resets the deck pressure Replaces the density and differential pair Rate-of-change and pressure ratio controllers Limit how fast MAP rises on rapid throttle opening; limit deck pressure to about 2.2 × ambient Used with an APC on some engines; the ratio limit acts mainly above critical altitude
Extra protection on some systems: an overboost warning light and an overboost relief valve that dumps deck pressure to ambient.
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Not every turbocharger uses a lone absolute pressure controller. The simplest system has no moving gate at all, just a fixed orifice in the exhaust bypass, so a set share of the gas always drives the turbo, and the throttle alone controls manifold pressure; slam the throttle open and it will easily overboost. More sophisticated systems pair a density controller with a differential pressure controller. The density controller’s nitrogen-filled bellows sense deck pressure and temperature and limit the maximum manifold pressure at full throttle. The differential controller senses the pressure drop across the throttle and works at every other throttle position; only one of the pair is in charge at any moment. A variable pressure controller does both jobs with a cam on the throttle. Some engines use a rate-of-change controller to stop overboost on rapid throttle opening, and a pressure ratio controller limiting deck pressure to about two point two times ambient.
Part 4 · Turbochargers
Throttle sensitivity, bootstrapping, overboost and lag Each throttle move starts a chain reaction through the controller, gate and turbo: throttle sensitivity Bootstrapping : an unregulated, continual drift of MAP at part throttle; a nuisance, not a dangerOverboost : MAP above the limit: high loads, detonation , serious damageTurbo lag : the turbo takes time to spool up, so response to rapid throttle opening is worse than a plain engineMove the throttle slowly ; to increase power raise RPM before MAP , to reduce it lower MAP before RPM
Pilot moves throttle
MAP and the throttle Δp change
Controller re-sets its oil bleed
Actuator moves the waste gate
Turbine speed changes
Deck pressure changes
THROTTLE
SENSITIVITY
More power: RPM up first, then MAP up
Less power: MAP down first, then RPM down
move the throttle slowly and let MAP settle
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
A turbocharged engine can feel twitchy, and the loop on the right shows why. When you move the throttle, the manifold pressure and the pressure drop across the throttle change. The controller senses that and resets its oil bleed. The actuator moves the waste gate, the turbine speed changes, the deck pressure changes, and that changes the manifold pressure again. Round it goes until things settle. This is throttle sensitivity. At part throttle the manifold pressure can keep drifting by itself, which is called bootstrapping; it is a nuisance rather than a danger. Overboost is different: too much manifold pressure means high loads, detonation and serious damage. And when you open the throttle quickly, the turbo needs time to spool up, which is turbo lag. So move the throttle slowly. To increase power, raise the RPM first, then the manifold pressure. To reduce power, lower the manifold pressure first, then the RPM.
Part 4 · Turbochargers
When the waste gate system fails Think about where the gate is stuck, and what the air density is doing.
Seized in the climb Turbo speed can no longer rise as the air thins, so deck pressure, MAP and power fall as the climb continues.
Seized in the descent Gate stuck well closed while the air gets denser: MAP climbs, power increases , and the engine can be overboosted .
Oil supply lost Nothing holds the gate shut: the spring opens it fully , the turbo slows and boost is lost. Turbo bearings are at risk too.
Overboost protection Watch MAP; some systems add an overboost light and a relief valve that dumps deck pressure.
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Waste gate failures are a favourite exam topic, and you can reason them out. Suppose the gate seizes during the climb, before critical altitude. The turbo can no longer speed up as the air thins, so the deck pressure, the manifold pressure and the power all fall as the climb continues. Now suppose it seizes during a descent, when it was well closed for high altitude. As the aircraft descends into denser air the same turbine flow pushes more and more pressure into the manifold, so the power increases and the engine can be overboosted. If the oil supply to the actuator fails, nothing holds the gate shut, so the spring opens it fully, the turbo slows, and boost is lost; the turbo bearings, which share that oil, are also in danger. Finally, watch the manifold pressure gauge: some systems add an overboost warning light and a relief valve.
Part 5 · Internal superchargers
The gear-driven internal supercharger Driven by gears from the rear of the crankshaft , usually 6 : 1 to 12 : 1 Fitted downstream of the throttle : it compresses the mixture , so its outlet pressure is the MAP Typical of engines of about 250 BHP and above A spring drive unit (sometimes with a centrifugal clutch) limits torque during rapid acceleration or deceleration Older big engines: two-speed drives or two impellers in series Holds sea-level MAP to about 5 000–10 000 ft at rated power
Carburettor and throttle
air
mixture into the eye
Cylinders
diffuser diffuser
impeller
impeller pinion
intermediate gears
crankshaft gear with
spring drive unit
≈ 10 : 1
step-up gearing
(usually 6 to 12 : 1)
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The internally driven supercharger is found on medium and high-powered engines, roughly two hundred and fifty brake horsepower and up. A shaft splined into the rear of the crankshaft drives the impeller through step-up gears, usually somewhere between six and twelve to one, so the impeller always turns at a fixed multiple of engine speed. It sits downstream of the carburettor and throttle, so it compresses the fuel and air mixture, and what leaves the impeller goes straight into the manifold: its output pressure is the manifold pressure. The drive often includes a spring drive unit, sometimes with a centrifugal clutch, to stop huge torque loads reaching the impeller and gears when the engine accelerates or decelerates sharply. Big engines of the past used two-speed gearing, low gear low down and high gear up high, or two impellers in series. A typical modern single-speed unit holds sea-level manifold pressure up to about five to ten thousand feet at rated power.
Part 5 · Internal superchargers
The throttle and the automatic boost control The impeller is sized for altitude, so low down it could give far too much pressure At sea level the throttle is only partly open , even at take-off power In the climb it must be progressively opened to hold the same boost Automatic boost control (ABC) : capsules sensitive to boost pressure move the throttle butterfly The throttle lever becomes a boost selector ; the RPM lever sets engine and impeller speed Throttle fully open: full throttle height ; above it, MAP and power fall
Automatic boost control (ABC)
capsules
sense boost
manifold (boost) pressure
linkage
throttle butterfly
on the carburettor
Sea level
partly open
Climbing
opening
Full throttle height
fully open
Lever not moved: the ABC opens the butterfly in the climb
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
A supercharger is designed to give sea-level pressure at altitude, so its impeller must spin fast. Down low, in dense air, that same impeller could produce far too much pressure, enough to cause severe detonation and overstress the engine. So at sea level the throttle butterfly is only partly open, even for take-off. As the aircraft climbs, the butterfly has to be opened progressively to keep the same boost. Rather than make the pilot do this all the way up, an automatic boost control, mounted on the carburettor, does it for him. Its capsules are sensitive to boost pressure, and through a linkage they move the throttle butterfly to hold the boost the pilot has selected. The throttle lever has become a boost selector, while the RPM lever controls the engine, and with it the impeller speed. When the butterfly is fully open, the aircraft has reached full throttle height.
Part 5 · Internal superchargers
Why the supercharged engine gains power as it climbs At sea level, same RPM and MAP: the supercharged engine gives slightly less power; the impeller absorbs some Climbing at constant MAP and RPM, power increases up to full throttle height Why: colder air is denser at the same MAP , and lower outside pressure means less exhaust back pressure Above full throttle height , MAP and power fall like a plain engine The turbo engine is the opposite: its power decreases because its back pressure rises
0
5
10
15
20
25
40
60
80
100
Altitude (thousands of feet)
Power (% of the NA engine at sea level)
full throttle height
internally supercharged
turbocharged
normally aspirated
SL: the impeller drive costs some power
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a result that surprises many students. Compare a supercharged engine with an otherwise identical plain engine, at the same RPM and manifold pressure. At sea level the supercharged engine gives slightly less power, because some of its crankshaft power is spent turning the impeller. But climb at constant manifold pressure and RPM, and the supercharged engine’s power increases. Two reasons. The outside air is colder, so the charge is denser for the same manifold pressure, and more mass goes in. And the outside pressure is lower, so the exhaust has less back pressure to push against, and the cylinders scavenge better; this is the main reason the exam wants. The gain continues until full throttle height, after which the power falls away like a normally aspirated engine. A turbocharged engine behaves the other way, because closing its waste gate raises the exhaust back pressure.
Part 5 · Internal superchargers
Full throttle height and rated altitude
0
2
4
6
8
10
12
14
16
20
30
40
50
Altitude (thousands of feet)
Manifold pressure (inHg)
full-throttle MAP, rated RPM
full-throttle MAP, reduced RPM
rated boost 40 inHg
reduced boost 34 inHg
rated altitude ≈ 8,000 ft
lower FTH ≈ 5,700 ft
higher FTH ≈ 12,200 ft
Rated RPM + rated boost
→ rated altitude
Rated boost, less RPM
→ FTH lower
Rated RPM, less boost
→ FTH higher Rated altitude = full throttle height at rated power (rated RPM and rated boost). To hold rated boost with less RPM , the throttle must be opened further .
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Full throttle height is the greatest height at which a given boost can be maintained at a given RPM. Look at the graph. The blue curve is the most manifold pressure the supercharger can deliver at full throttle at rated RPM; it falls as the air thins. Where it meets the rated boost line, at about eight thousand feet here, the throttle is fully open. Full throttle height at rated power has a special name: rated altitude. Now select rated boost but less RPM. The impeller turns more slowly, gives less pressure, so the throttle has to be opened further to make up for it, and full throttle is reached lower down, at about five and a half thousand feet. Select rated RPM but less boost, and the throttle opens more slowly in the climb, so full throttle height rises, to about twelve thousand feet. Remember: less RPM, lower full throttle height; less boost, higher.
Part 5 · Words the exam uses
Power ratings and heights Term Meaning Take-off power Maximum power for take-off; time-limited (often 5 minutes) Rated power (MCP) Maximum continuous power: the most power, at rated RPM and rated boost , allowed for unrestricted continuous operation Climb power May also carry a time limit Full throttle height Greatest height at which a specified boost can be held at a specified RPM (supercharger) Rated altitude Full throttle height at rated power : the highest altitude at which rated boost can be held at rated RPM Critical altitude Turbocharger: height at which the waste gate is fully shut ; above it the selected MAP cannot be held Static boost Manifold pressure reading with the engine stopped : the ambient pressure
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pin down the vocabulary, because examiners often test definitions. Take-off power is the maximum power available, and it is time-limited, often to five minutes; climb power may be limited too. Rated power, also called maximum continuous power, is the greatest power, at a rated RPM and a rated boost, at which continuous operation is permitted; its use is unrestricted. Full throttle height belongs to the supercharged engine: the greatest height at which a specified boost can be held at a specified RPM. Rated altitude is the full throttle height at rated power. Critical altitude belongs to the turbocharged engine: the height at which the waste gate becomes fully shut, above which the selected manifold pressure can no longer be held. Do not mix those last two up. And static boost is simply what the manifold pressure gauge reads with the engine stopped.
Part 6 · Comparison and checks
Supercharger or turbocharger? Internal supercharger Turbocharger Drive Internally, by gears from the crankshaft Externally, by an exhaust turbine Speed set by Engine RPM Waste gate position (and engine RPM)Compresses Mixture , downstream of the throttleAir , upstream of the throttleControl unit ABC senses manifold pressure, moves the throttle APC senses deck pressure, moves the waste gate Compressor outlet vs MAP Equal to MAPGreater than MAPManifold pressure set by Throttle Throttle Exhaust back pressure in the climb Decreases : power risesIncreases : power fallsResponse to a rapid throttle opening Instant Slower: turbo lag
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put the two side by side. The internal supercharger is driven by gears from the crankshaft, so its speed is set by engine RPM. The turbocharger is driven by an exhaust turbine, so its speed is set mainly by the waste gate. The supercharger compresses mixture, downstream of the throttle, so its outlet pressure equals the manifold pressure. The turbocharger compresses air, upstream of the throttle, so its outlet pressure is greater than the manifold pressure, by the drop across the throttle. The supercharger’s automatic boost control senses manifold pressure and moves the throttle; the turbo’s controller senses deck pressure and moves the waste gate. In both, the throttle sets the manifold pressure. In the climb the supercharger enjoys falling back pressure, the turbo suffers rising back pressure. The turbo is the cheaper option and uses wasted energy, but it suffers turbo lag, while the supercharger responds instantly.
Part 6 · Comparison and checks
Climbing at a constant throttle lever, full rich Normally aspirated Turbocharged Internally supercharged MAP Falls about 1 inHg / 1000 ftHeld to critical altitude, then fallsHeld to full throttle height, then fallsPower Falls Falls slowly , then fasterRises , then fallsVolumetric efficiency Falls (thinner charge) Decreases Increases CHT Decreases (mixture richens)Increases — What moves by itself Nothing Waste gate closes progressively ABC opens the throttle progressively Lowest pressure in the induction system Just downstream of the throttle Compressor inlet, downstream of the air filter Downstream of the throttle , at the impeller eyeService ceiling Lowest Higher Higher
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Examiners love to ask what happens when each type of engine climbs with the throttle lever left alone and the mixture in full rich, so here it is in one table. The plain engine loses manifold pressure and power from the start, and with the mixture growing richer its cylinder head temperature decreases. The turbocharged engine holds its manifold pressure, because the waste gate closes progressively, but its power falls slowly, its volumetric efficiency decreases and its cylinder head temperature increases, because back pressure and charge temperature are rising. The supercharged engine holds its manifold pressure because the automatic boost control opens the throttle, and its power and volumetric efficiency increase up to full throttle height. Notice where the lowest pressure is: in a turbo system it is at the compressor inlet, just after the air filter; in a supercharged engine it is between the throttle and the impeller. And both boosted engines raise the service ceiling.
Part 6 · Comparison and checks
Static boost and the reference RPM check Static boost : the MP gauge reading before start , about ambient (29.92 inHg or zero boost at ISA sea level)After start, MAP drops well below static, and starts rising about 1600–1700 RPM Propeller on the fine pitch stop : open the throttle until MAP is back to static boost , then read the RPM It should match the placarded reference RPM (typically about 2000) within about ±50 RPM Outside limits: a cylinder down on power , ignition or carburettor faults, or a wrong prop low-pitch stop A new reference RPM is set after a carburettor or magneto change
10
20
30
40
50
MAP
inHg
0
5
10
15
20
25
30
RPM
× 100
MAP back to static boost
yellow mark: reading before start
read the RPM: 2 000
REF RPM 2000 ± 50
Propeller on the fine pitch stop (maximum RPM selected)
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
28
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a neat way to check that an engine is giving its proper power. Before start, note what the manifold pressure gauge reads. With the engine stopped it simply shows the outside pressure, about twenty-nine point nine two inches at an I S A sea-level aerodrome, and this reading is called static boost. Once the engine has started, the manifold pressure drops well below static, and it will not begin to rise until about sixteen or seventeen hundred RPM. With the propeller on its fine pitch stop, open the throttle until the manifold pressure regains the static boost figure, and read the RPM. It should match the reference RPM, placarded in the cockpit, typically about two thousand, within about fifty RPM. If it does not, suspect a cylinder down on power, an ignition fault, a carburettor out of adjustment, or a wrongly set propeller low-pitch stop. A new reference RPM is set whenever a carburettor or magneto is changed.
Part 6 · Comparison and checks
A few more facts worth knowing Diesel engines Lose volumetric efficiency with height and heat too, so they are often turbocharged with intercoolers .
Fuel A turbocharged piston engine is still a spark-ignition engine and burns AVGAS , not jet fuel.
Fuel flow More compressor discharge pressure means more mass of air, so the carburettor or injection system gives more fuel flow .
Turbo speed Turbo rotors may run at up to about 110 000 RPM ; the bearings live on engine oil, so oil care matters.
Which is best? Turbo: cheaper , uses wasted energy, best value at ground level. Supercharger: power that grows with height , instant response .
Mounting The turbo can sit on the engine or the firewall , shielded from fuel and oil lines because it runs very hot.
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
29
e-books by eatpl.in · © 2026 · Do not copy or distribute
A few more facts round off the picture. Diesel aero engines also lose volumetric efficiency at height and on hot days, so they are often turbocharged, with intercoolers to restore the density. A turbocharged piston engine is still a spark-ignition petrol engine, so it burns avgas, not jet fuel. When the compressor discharge pressure goes up, more mass of air is flowing, and the carburettor or injection system responds with more fuel flow. Turbo rotors spin at up to about one hundred and ten thousand RPM, and their bearings depend on engine oil, so good oil management matters. Which system is best? For extra power at ground level for the money, the turbocharger wins, and it uses energy that would otherwise be wasted. But for power that grows with altitude, and instant response to the throttle, the internal supercharger wins. Finally, the turbo may be mounted on the engine or on the firewall, shielded from fuel and oil lines because it runs so hot.
Summary
What to take into the exam Power and air Power ∝ mass of charge. ISA MSL 15 °C, 29.92 inHg, 14.7 psi. DA ≈ PA + 118 ft per °C above ISA.
NA climb MAP falls ~1 inHg/1000 ft, power falls. Full rich at fixed throttle: mixture richer, CHT down.
Boost and MAP Boost: psi from 14.7 (ISA MSL). MAP: absolute inHg. 2 inHg ≈ 1 psi. +10 psi ≈ 25 psi abs.
Compressor Centrifugal: eye → tip; diffuser slows the air, raises pressure. Up to 3 : 1. Intercooler after the compressor cuts detonation.
Turbocharger Exhaust turbine + compressor on one shaft; engine oil. Air, upstream of throttle. Outlet > MAP.
Waste gate In the turbine bypass. Spring opens, oil closes. Open at start, shut at idle, nearly open at SL take-off, closing in climb, shut at critical altitude.
Supercharger Geared 6–12 : 1, mixture, downstream of throttle, outlet = MAP. ABC opens the throttle. Power rises to FTH.
FTH Rated altitude = FTH at rated power. Less RPM: FTH lower. Less boost: FTH higher. Static boost and reference RPM ±50.
Chapter 11 · Piston Engine Performance, Supercharging and Turbocharging
30
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather it all up. Power depends on the mass of charge, and density altitude, pressure altitude plus one hundred and eighteen feet per degree above standard, tells you what the engine feels. A plain engine loses about an inch of manifold pressure per thousand feet. Boost is measured in psi from standard sea-level pressure, manifold absolute pressure in inches of mercury, and two inches is about one psi. The centrifugal compressor’s diffuser turns speed into pressure, and an intercooler cuts detonation. The turbocharger compresses air upstream of the throttle, driven by an exhaust turbine on a common shaft, controlled by a waste gate in the turbine bypass that the spring opens and oil closes, fully shut at critical altitude. The internal supercharger is geared to the crank, compresses mixture downstream of the throttle, and its automatic boost control opens the throttle as you climb. And remember: less RPM lowers the full throttle height, less boost raises it.