Engines · Chapter 23
Reverse Thrust How jet engines turn their efflux forward to help stop the aircraft, the three types of reverser, and the safeguards, indications and limits that go with them.
fan air turned forward
core: still aft
REVERSE THRUST
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter twenty three is about reverse thrust. On a wet, icy or short runway, wheel brakes alone can struggle, because they depend on friction between the tyres and the surface. Reverse thrust stops the aircraft by turning the engine's efflux forward, so it works without any friction at the wheels. We will look at why it matters, at the three types of reverser, clamshell, bucket and cold stream blocker, at how they are operated, and then at the safeguards, warning lights and speed limits that keep this powerful system from becoming a hazard.
Roadmap
Reverse thrust in four steps 1 · Why Brakes need friction; reverse does not. Stopping distances and forces, with numbers.
2 · Types Clamshell, bucket and cold-stream blocker reversers; which stream each turns.
3 · Control Actuation, the piggy-back lever, interlocks and the five safeguards.
4 · Use Warning lights, the 60–80 kt reduction, re-ingestion, asymmetry, ground manoeuvring.
Chapter 23 · Reverse Thrust
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan. First, why reverse thrust exists at all: wheel brakes need friction, and on a wet or icy runway there is not much of it, while reverse thrust works on the aircraft directly. We will put numbers on stopping distances and on the forces involved. Second, the three types of reverser: the clamshell door and bucket types, which turn the hot exhaust, and the cold stream blocker type used on high-bypass fans, which turns only the fan air. Third, control: how the reversers are moved, how the reverse lever sits on the thrust lever, and the five safeguards built into selecting reverse. Finally, how reverse is used: the warning light, the speed at which reverse is reduced and cancelled, the danger of re-ingesting hot gas and debris, asymmetry, and why reverse is not normally used for ground manoeuvring.
Part 1 · Why reverse thrust?
When brakes are not enough Modern brakes with anti-skid are very efficient, but they need tyre friction On wet or icy runways friction collapses, and the brakes can become a liability Reverse thrust acts on the aircraft without friction at the wheels Selected as soon as the weight is firmly on the main wheels , together with the ground spoilers Computed for a 60 t jet: reverse saves about 41% of the stop on ice, 20% on a dry runway
Stopping distance from 140 kt (m)
0
1000
2000
3000
690
550
Dry
μ 0.35
1310
920
Wet
μ 0.17
2660
1580
Icy
μ 0.07
brakes + drag
+ reverse thrust
Chapter 23 · Reverse Thrust
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Modern wheel brakes, with anti-skid units and other clever devices, are extremely efficient, but they all depend on friction between the tyres and the runway. On a wet runway, and even more on ice, that friction collapses, and heavy braking can make the wheels skid, so the brakes can even become a liability. Reverse thrust does not depend on the tyres at all: it pushes directly on the aircraft. It is selected as soon as the weight is firmly on the main wheels, and together with the ground spoilers it can shorten the landing roll dramatically. The chart is computed for a sixty tonne jet landing at one hundred and forty knots. On a dry runway reverse saves a modest amount. On a wet runway it saves much more, and on an icy runway it shortens the stop by around forty per cent. That is why landing on a wet or icy runway in a crosswind need hold no terrors for a capable pilot.
Part 1 · Why reverse thrust?
What stops the aircraft, and when
140
120
100
80
60
40
20
0
0
30
60
90
120
Ground speed (kt), decreasing along the landing roll →
Retarding force (kN), icy runway
reverse thrust (two engines)
aerodynamic drag
wheel brakes, μ 0.07
reverse idle
Why reverse matters
Reverse and drag are largest at
high speed, just when the brakes
are least effective (wheels still
spinning up, lift not yet dumped).
They act on the aircraft, not
through the tyres, so they work
even on ice or standing water.
Computed: 60 t, wing area 122 m², drag coefficient 0.10 with spoilers, 2 × 30 kN reverse rising slightly with speed, reverse idle from 70 kt, stowed at 50 kt.
Chapter 23 · Reverse Thrust
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph shows what actually stops the aircraft on an icy runway, as the speed falls from one hundred and forty knots. Read it from left to right, because speed decreases along the landing roll. The green line is reverse thrust from two engines. It is the biggest force at high speed, and it even grows slightly with speed, because the intake momentum drag adds to it. The blue line is aerodynamic drag, with the spoilers up; it goes with the square of speed, so it is large at first and fades away. The dashed grey line is the wheel brakes, at a friction coefficient of only nought point nought seven: small and constant. So reverse thrust and drag do most of the work at high speed, exactly when the brakes are weakest. At seventy knots the reverse is reduced to idle, and at fifty knots it is stowed, leaving the brakes to finish the job.
Part 1 · How it works
Turning the efflux forward
Turning the fan air forward
Worked example (one engine)
45°
fan air leaves about 45° forward
core still aft
only the forward component
of the efflux brakes the aircraft
Fan air
400 kg/s at 200 m/s, 45° fwd
Aircraft speed
60 m/s (≈ 117 kt)
Fan reverse
400 × (200 cos45° + 60) = 81 kN
Core forward
80 × (400 − 60) = 27 kN
Net reverse
≈ 53 kN (ideal, before losses)
Reverse force comes from the forward component of the efflux plus the intake momentum drag. Gas cannot be turned fully forward, so reverse thrust is well below forward take-off thrust.
Chapter 23 · Reverse Thrust
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
How does a reverser actually produce a backwards force? It does not reverse the engine; the compressor and turbine keep turning the same way. Instead, it changes the direction of the gas flow. In the example, the fan air is turned so that it leaves about forty five degrees forward. Only the forward component of its velocity helps. On top of that, the aircraft is still moving, so the air entering the intake brings its intake momentum drag, which also retards the aircraft. One engine moving four hundred kilograms a second of fan air at two hundred metres a second, with the aircraft at sixty metres a second, gives about eighty one kilonewtons of reverse force. But the hot core is still blowing aft, giving about twenty seven kilonewtons forward, so the net reverse is about fifty three kilonewtons, before losses. Because the gas cannot be turned fully forward, reverse thrust is always well below forward take-off thrust.
Part 2 · Types
Three basic thrust reversers Clamshell doors Doors inside the jet pipe close it; hot exhaust leaves forward through cascade vanes . Usually pneumatic (HP compressor air).
Bucket (external door) Two half-buckets at the rear of the jet pipe swing back behind the nozzle and deflect the hot jet forward. Usually hydraulic .
Cold-stream (blocker) High-bypass fans only : blocker doors close the bypass duct; cold fan air leaves forward through cascades. Hot stream unaffected.
Chapter 23 · Reverse Thrust
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are three basic types of thrust reverser in use. Clamshell doors sit inside the jet pipe. When deployed they close it off, so the hot exhaust escapes sideways through cascade vanes that turn it forward. They are usually pneumatic, powered by high pressure compressor air. The bucket, or external door, type uses two half buckets that form the rear of the jet pipe; they swing backwards behind the nozzle and deflect the hot jet forward. These are normally hydraulic. The third is the cold stream, or blocker, reverser, used only on high-bypass fan engines. It blocks the bypass duct and turns only the cold fan air forward, through cascades, leaving the hot core stream unaffected. All three reverse the direction of the gas flow, not the rotation of the engine, and all are driven by hydraulic or pneumatic actuators, or by motors driving screw shafts.
Part 2 · Types
Clamshell door reverser Named after the shape of its doors Usually pneumatic : rams powered by HP compressor (P3) air Stowed, the doors cover the cascade vanes and form part of the jet pipe Deployed, they close the normal exit : the gas escapes through the cascades, forward Lower cascades angled outboard as well, to keep hot gas and debris away from the intake
Stowed: forward thrust
Deployed: reverse thrust
cascades covered
clamshell doors
close the jet pipe
gas out through the
cascades, forward
Chapter 23 · Reverse Thrust
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The clamshell reverser takes its name from the shape of its doors. They are usually moved by pneumatic rams, powered by high pressure air taken from the compressor, P three air. In the stowed, forward thrust position the doors lie flush in the jet pipe and cover a set of cascade vanes. Watch them move. When they are deployed, the doors swing in and close off the normal exhaust exit, which uncovers the cascades, so the gas escapes through the vanes in a forward direction, opposing the aircraft's motion. So a clamshell reverser changes the direction of the exhaust gas; it does not simply block it. The lower cascade vanes are angled outboard as well as forward. That gives the reversed exhaust a sideways component and reduces the chance of hot gas and debris being re-ingested by the engine intake.
Part 2 · Types
Bucket (external door) reverser The rear of the jet pipe is shaped as two halves of a bottomless bucket Hinged so they swing backwards and close behind the nozzle The hot jet strikes them and is deflected forward and outward Also called a target reverser Normally hydraulically operated
Stowed: buckets form the nozzle
Deployed: buckets behind the nozzle
buckets swing back
and close behind the jet
Chapter 23 · Reverse Thrust
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The bucket, or external door, reverser works outside the nozzle. The rear part of the exhaust pipe is shaped like two halves of a bottomless bucket. In forward thrust they simply form the end of the jet pipe. When reverse is selected, they are hinged so that they swing backwards and close together behind the nozzle. The hot jet now strikes the inside of the buckets and is deflected forward and outward, producing reverse thrust. Because the jet hits them like a target, this design is also called a target reverser. It is normally operated hydraulically. Like the clamshell, it uses the hot exhaust stream, so the buckets must withstand high temperatures, and like the clamshell it is found mainly on turbojets and low-bypass engines, where most of the thrust is in the hot jet.
Part 2 · Types
Cold-stream (blocker) reverser Used only on high-bypass fan engines , where most thrust comes from the fan A translating sleeve slides aft, uncovering cascade vanes Blocker doors close the bypass duct: cold fan air leaves forwardThe hot stream is not reversed : it still gives forward thrust Classic drive: an air motor via flexible shafts to screwjacks; many modern types are hydraulic
Cold-stream (blocker) reverser
sleeve moved aft
cold fan air out through the cascades, forward
core
hot stream
unaffected
blocker doors
Chapter 23 · Reverse Thrust
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a high-bypass fan engine most of the thrust comes from the fan, so it makes sense to reverse only the fan air. That is the cold stream, or blocker, reverser, used only on high-bypass engines. Watch it work. The translating sleeve, the rear part of the fan cowl, slides aft and uncovers rows of cascade vanes. At the same time the blocker doors swing into the bypass duct and close it. The cold fan air can no longer go aft, so it is diverted through the cascades and turned forward. The essential difference from the other two types is that the hot core stream is not reversed at all: it carries on aft, still giving some forward thrust. In the classic design an air motor, whose speed and direction are set by the reverse lever, drives the doors through flexible shafts and screwjacks; many modern engines use hydraulic actuators instead.
Part 2 · Types
More reverse RPM: what happens to the hot stream? With blockers deployed, more RPM gives more reverse from the fan air It also gives more forward thrust from the hot core The net reverse still increases , because the fan dominates TGT rises : watch EGT in reverse Exam trap: "forward thrust from the hot gases would decrease " is the incorrect statement
Reverse power against N1
20
30
40
50
60
70
80
-40
0
40
80
N1 % (reverse lever) · y: kN, one engine
fan air: reverse ↑
net reverse ↑
hot core: forward ↑ (plotted below zero)
More RPM: fan reverse, core forward thrust
and TGT all increase; net reverse still grows
Chapter 23 · Reverse Thrust
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a favourite exam question. Once the blocker doors are fully deployed, what happens as you increase reverse RPM? The fan moves more air, so the reverse thrust from the blocked, diverted fan air increases. But the core also runs faster and hotter, and since its exhaust is still going aft, the forward thrust from the hot gases increases too. The graph, computed for one engine, shows both, with the core thrust plotted as negative. Because the fan stream is so much bigger, the net reverse force still increases with RPM. And the turbine gas temperature rises as well, which is why exhaust temperature must be watched in reverse. So in the list of statements, forward thrust from the hot gases would increase, reverse thrust from the blocked air would increase, and T G T will increase. The incorrect one is that forward thrust from the hot gases would decrease.
Part 2 · Types
The three types compared Clamshell Bucket (external) Cold-stream blocker Gas stream reversed Hot exhaustHot exhaustCold bypass air onlyWhere Inside the jet pipe Behind the nozzle Bypass duct, fan cowl How the gas leaves Through cascades Deflected by the buckets Through cascades Usual power Pneumatic (P3 air)Hydraulic Air motor + flexible shafts (or hydraulic) Engines Turbojets, low bypass Turbojets, low bypass High-bypass fans onlyCore in reverse Reversed Reversed Still gives forward thrust
Chapter 23 · Reverse Thrust
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us compare the three types side by side. The clamshell and the bucket both reverse the hot exhaust; the cold stream reverser reverses only the cold bypass air. The clamshell works inside the jet pipe and lets the gas out through cascades; the bucket works behind the nozzle and deflects the jet with its buckets; the blocker works in the bypass duct, again using cascades. The clamshell is usually pneumatic, using compressor delivery air, the bucket usually hydraulic, and the classic blocker system uses an air motor and flexible shafts, though many modern engines use hydraulic actuators. Clamshells and buckets are found on turbojets and low-bypass engines; blockers only on high-bypass fans. And remember that with a blocker reverser the core still produces forward thrust. In the exam, a big fan engine gets its reverse thrust by blocking the bypass air.
Part 3 · Control
The reverse lever and the selection sequence
Thrust lever with piggy-back reverse lever
The sequence
thrust lever at IDLE
reverse lever
lifted up and back
aft
forward thrust →
Interlocks:
reverse only from forward IDLE
forward lever locked while
the reverse lever is raised
1
Thrust lever to IDLE
2
Weight on the main wheels
(air/ground logic)
3
Raise reverse lever to the
deploy (reverse idle) position
4
Doors unlock and move: amber
light
5
Doors fully deployed: interlock frees
the lever
6
Reverse power above idle, as
required
Each engine with a reverser has its own reverse lever, normally mounted piggy-back on its thrust lever.
Chapter 23 · Reverse Thrust
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each engine with a reverser has its own reverse thrust lever, normally mounted piggy-back on the front of its thrust lever. Mechanical interlocks make it impossible to raise the reverse lever unless the thrust lever is at idle, and while the reverse lever is raised, the thrust lever cannot be moved forward. The sequence on landing goes like this. Thrust levers to idle. Once the main wheels are on the ground, the air ground logic allows the system to work. The pilot lifts the reverse levers up and back to the deploy position, which is reverse idle. The doors unlock and start to move, and the amber reverser light comes on. Only when the doors are fully deployed does a second interlock release, allowing the reverse lever to be pulled further back for reverse power above idle. So before reverse can be selected, the forward thrust lever must be pulled back to idle.
Part 3 · Control
The five safeguards 1 · Idle first Reverse cannot be selected until the thrust lever is at idle .
2 · On the ground Reverse cannot be activated until there is weight on the main wheels (air/ground logic).
3 · Deployed before power Reverse RPM cannot rise above idle until the doors are fully deployed .
4 · Uncommanded deploy If the doors move to reverse while forward thrust is selected, the throttle may close to idle automatically.
5 · Uncommanded stow If the doors move to stowed while reverse is selected, the reverse lever is driven back to the deploy (reverse idle) position.
Why A reverser in the wrong position at high power can cause loss of control. Each safeguard stops high power with the doors in the wrong place.
Chapter 23 · Reverse Thrust
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Like many beneficial things, a reverser that is wrongly serviced or mishandled can become more of a curse than a blessing, so five safeguards are built into reverse selection. One: reverse cannot be selected until the thrust lever is at idle. Two: reverse cannot be activated until there is weight on the main wheels, through the air ground logic. Three: reverse RPM cannot be increased above idle until the doors have reached the fully deployed position. Four: if the doors inadvertently move towards reverse while forward thrust is selected, the throttle may automatically close to idle. Five: if the doors inadvertently move to the stowed position while reverse thrust is selected, the reverse lever is automatically driven back to the reverser deploy, or reverse idle, position. The common theme is that the engine must never give high power with the doors in a position that nobody asked for.
Part 3 · Indication
Reverser warning lights and displays A REVERSE THRUST warning light , usually amber , in full view of the crew It is on whenever the doors are unlocked and away from STOWED It does not mean reverse thrust is being produced Other indications vary by type: reverser deployed , reverser operating (often green when deployed) On modern aircraft the reverser state is shown on EICAS or ECAM
REV
N1
amber: unlocked / in transit
REV
N1
green: fully deployed
REVERSER UNLOCKED
Dedicated amber light: on whenever the doors are
unlocked and away from STOWED
Modern aircraft: shown on EICAS or ECAM
Chapter 23 · Reverse Thrust
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The crew must always know where the reverser doors are. So a reverse thrust warning light is fitted, usually amber, somewhere on the forward instrument panel in full view of both pilots. The key fact is what turns it on: the light illuminates whenever the reverser doors are unlocked and away from their stowed, forward thrust, position. It does not mean that reverse thrust is being produced, nor that reverse has merely been selected or armed; it means the mechanism is unlocked. Other indications depend on the aircraft type, for example reverser deployed, or reverser operating. On modern aircraft the reverser state appears on the engine display, on E I C A S or E C A M, typically as an amber R E V while the doors are unlocked or in transit, turning green when they are fully deployed.
Part 3 · Indication
Why so many locks and interlocks? A reverser deploying in flight can cause a violent yaw, roll and loss of lift on that wing So the system is locked stowed , and powered only with air/ground logic satisfied An unlocked reverser is shown at once by the amber light Uncommanded movement brings the engine to idle (safeguards 4 and 5) There is normally no upper speed limit for selecting reverse on the ground
Deploy logic (simplified)
Thrust lever at idle
Weight on main wheels
Reverse lever raised
AND
Power to the
actuators: unlock
Amber: unlocked
Deployed: power free
Doors stay mechanically
locked stowed unless all
three conditions are met
Uncommanded movement → engine to idle
Chapter 23 · Reverse Thrust
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why all these locks and interlocks? Because a reverser that deploys in flight is dangerous. On a wing-mounted engine it produces a large backwards force on one side, causing a violent yaw and roll, and the disturbed airflow over the wing behind it reduces lift on that side. So the doors are mechanically locked in the stowed position, and the system can only be powered when the air ground logic says the aircraft is on the ground. If anything unlocks, the amber light tells the crew at once, and if the doors move without being commanded, the engine is automatically brought back to idle. Once on the ground, there is normally no restriction on the upper speed at which reverse may be selected; in fact it is most effective at high speed. What some aircraft do have is a minimum speed restriction, which brings us to re-ingestion.
Part 4 · Use
Reverse on the landing roll
0
5
10
15
20
25
30
0
50
80
100
150
Seconds after touchdown (wet runway)
Ground speed (kt)
full reverse
reverse idle
stowed: brakes only
60–80 kt: to reverse idle
≈ 50 kt: stow
Typical procedure
Select reverse as soon as the
main wheels are firmly on.
At 60–80 kt reduce to reverse
idle: below this, hot gas and
debris may be re-ingested.
Stow at about 50 kt, when a
sudden need for full reverse
is no longer expected.
Computed landing roll (60 t, wet runway). Typical procedure: full reverse after touchdown, reverse idle at 60–80 kt , stow at about 50 kt .
Chapter 23 · Reverse Thrust
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is how reverse is typically used on the landing roll, computed for a wet runway. As soon as the main wheels are firmly on the ground, the pilot selects reverse, and the doors deploy within a couple of seconds. Full reverse, or the reverse power the procedures call for, is held while the speed is high and reverse is most effective. Then, at typically sixty to eighty knots, standard operating procedure on many aircraft is to bring the reverse levers back to reverse idle. The reverser stays deployed, ready in case full reverse is suddenly needed again. At about fifty knots, when no further need for sudden full reverse is expected, the levers are returned to the stowed position and the brakes finish the stop. The reason for that reduction at sixty to eighty knots is the risk of re-ingestion, on the next slide.
Part 4 · Use
Re-ingestion of hot gas and debris At high speed the reversed efflux is swept aft , clear of the intake At low speed or standing still, intake suction can overcome the deflection Hot gas and runway debris are drawn into the compressor: surge, overheating, FOD Cascades angled outboard help, but cannot prevent it at low speed Hence reverse idle by 60–80 kt and stow by about 50 kt ; never use high reverse power when slow
High speed: efflux swept away
Low speed: efflux reaches the intake
airflow
carried aft
intake suction
hot gas + debris
re-ingested
Chapter 23 · Reverse Thrust
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Re-ingestion is the main reason reverse thrust has a low speed restriction. At high speed, the reversed efflux leaving the cascades is quickly swept aft by the airflow, well clear of the intake. As the aircraft slows, the forward travelling gas reaches further and further ahead. At low speed, or standing still, the suction at the engine intake can overcome the deflection given to the exhaust, and hot gas, together with debris blown up from the runway, is drawn back into the compressor. The results can be catastrophic: compressor surge, over-temperature and foreign object damage. Angling the cascades outboard helps, but cannot prevent it at low speed. So using reverse thrust below the recommended speed may cause ingestion of the exhaust gases and foreign objects, which is why the procedure is reverse idle by sixty to eighty knots and stowed at about fifty.
Part 4 · Use
Ground manoeuvring and asymmetry Reverse thrust is not normally used for ground manoeuvring When in use, monitor engine indications, especially EGT Increase reverse RPM symmetrically : uneven spool-up causes yaw One reverser inoperative : total reverse is reduced, and a performance limitation may apply On a wing-mounted twin, the good reverser may not be usable either, because of asymmetry
reverse
forward idle
yaw towards the
reversing side
One reverser inoperative
Wing-mounted twin: the good reverser may also
be restricted (or not used) to avoid asymmetry
Landing performance penalty applies
Chapter 23 · Reverse Thrust
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Reverse thrust is not normally used for ground manoeuvring, for example to back away from a gate, because of the re-ingestion and debris risks we have just seen, and because of the hot gas thrown forward. Whenever reverse is used, the engine indications must be closely watched, in particular the exhaust gas temperature, which rises in reverse. Care is needed when increasing reverse RPM: the engines must respond together, because if one spools up faster than the other, the aircraft will yaw. If one engine's reverser is inoperative, the total reverse available is reduced, and a landing performance limitation may be imposed. On a twin with engines on wing pylons, using the one good reverser would push one side back while the other idles forward, as the diagram shows, so the good reverser may not be used either, because of the asymmetric effect.
Summary
What to take into the exam Purpose Stops without tyre friction: best on wet/icy runways and at high speed. Select when the weight is firmly on the main wheels.
Clamshell Doors inside the jet pipe, usually pneumatic (P3). Change the direction of the hot gas through cascades.
Bucket Two half-buckets swing back behind the nozzle. Usually hydraulic . Hot gas.
Blocker High-bypass only: blocks and turns the cold bypass air; hot stream unaffected. Air motor + flexible shafts.
Selection Thrust lever at idle ; weight on wheels; no power above idle until fully deployed.
Failures Uncommanded deploy: throttle to idle. Uncommanded stow: reverse lever back to deploy (reverse idle).
Light Amber light on whenever the doors are unlocked and away from stowed. Modern: EICAS/ECAM.
Limits Reverse idle at 60–80 kt, stow ≈ 50 kt: re-ingestion. Not for taxiing. Watch EGT; symmetric use.
Chapter 23 · Reverse Thrust
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Reverse thrust stops the aircraft without relying on tyre friction, so it matters most on wet and icy runways, and it is most effective at high speed; select it when the weight is firmly on the main wheels. The clamshell reverser, usually pneumatic, closes the jet pipe and changes the direction of the hot gas through cascades. The bucket reverser, usually hydraulic, swings two half buckets behind the nozzle. The blocker reverser, only on high-bypass fans, blocks and turns the cold bypass air, leaving the hot stream unaffected. Reverse can only be selected with the thrust lever at idle and weight on the wheels, and power cannot rise above idle until the doors are fully deployed. The amber light means the doors are unlocked and away from stowed. Reduce to reverse idle at sixty to eighty knots and stow at about fifty to avoid re-ingestion, and do not use reverse for taxiing.