Engines · Revision
Revision and Exam Practice The numbers, rules and traps that powerplant papers test again and again, with the full revision set and a practice paper.
inlet fan/LPC HPC exit comb. exit HPT exit LPT exit nozzle pressure · temperature · velocity 720° 15 : 1 +33 °C α = β − φ 60 % N2 2.5 g 400 Hz 1.83 m numbers · rules · traps © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the revision chapter of the engines course. Powerplant papers come back to the same small set of facts again and again: the valve timing, the mixture ratios, the icing temperatures, the blade angles, which turbine drives which compressor, where each temperature and pressure is measured, and which way things move when something fails. In this chapter we walk through the whole syllabus, one block per page: the piston engine, the propeller, the gas turbine and its systems. Because the same paper also mixes in airframe, systems and electrics questions, we finish with compact pages on those too. On every page look for the number to remember and the trap. Then work through the quiz, the question bank, the long revision set and the practice paper at the end.
How to use this chapter
The whole powerplant paper, one page per block Each page gathers one block: the numbers, the rules and the classic traps. Every revision and practice question links back to one of them.
Piston engines The cycle and valve timing, lubrication and cooling, ignition, fuel and mixture, carburettors and icing, supercharging.
Propellers Blade angle, angle of attack and twist; fixed pitch; the constant-speed unit, feathering, alpha and beta.
Gas turbines Spools and bypass, compressors, combustion and turbines, thrust and its measurement, performance, bleed and reverse.
Engine systems Oil, gearboxes, ignition and starting; the turbine fuel system in order, from booster pump to nozzle.
The rest of the paper Airframe and controls, hydraulics and gear, air conditioning, ice and fire, oxygen, emergency kit, fuel, electrics.
Traps and method Where marks are lost, how to read a stem, and the last-minute numbers. Then the questions.
Chapter 30 · Revision and Exam Practice
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This revision chapter squeezes the whole powerplant syllabus onto about two dozen pages. We start with the piston engine: the cycle, oil and cooling, ignition, fuel and mixture, carburettors and icing, and supercharging. Then the propeller, from blade angle to the constant-speed unit. Then the gas turbine: spools and bypass, compressors, the hot end, thrust and how it is measured, performance, bleed air and reverse thrust, followed by the engine systems and the fuel system in order. The general knowledge paper mixes in airframe, systems and electrics questions, so the last block covers those in compact form. On every page look for three things: the number to remember, the rule, and the trap. After the last page come the quiz, the question bank, a long revision set and a practice paper, each question linked back to the page that answers it.
Piston engine
The four-stroke cycle, timing and volumes Four strokes, five events, one power stroke in 720° ; firing interval = 720° ÷ cylinders Lead and lag: IO before TDC, EC after TDC (overlap), EO before BDC, IC after BDC At BDC ending the power stroke: exhaust open, inlet closed ; next come IO, EC, IC Spark before TDC , every second turn (impulse coupling: after TDC to start) Total volume = swept + clearance ; CR = total ÷ clearance; crank assembly = crankshaft, rods, pistons Power = torque × RPM ; IHP = PLANE ÷ 33 000; BHP = IHP − FHP Typical valve and ignition timing (crank degrees) TDC BDC spark 25° BTDC IO 20° BTDC EC 15° ATDC EO 55° BBDC IC 55° ABDC overlap 35° around TDC clockwise = crank rotation inlet open exhaust open Volumes and compression ratio 80 cc swept 400 cc clearance = 480 cc CR = total ÷ clearance = 480 ÷ 80 = 6 : 1 Firing interval 720° ÷ n: 4 cyl 180°, 6 cyl 120°
Chapter 30 · Revision and Exam Practice
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The piston engine block starts with the cycle. Four strokes, five events, and one power stroke every seven hundred and twenty degrees of crank, so the firing interval is seven twenty divided by the number of cylinders. The diagram shows typical timing. The inlet opens about twenty degrees before top dead centre and the exhaust closes about fifteen after it: that is the overlap. The exhaust opens well before bottom dead centre, and the inlet closes well after it. So at bottom dead centre at the end of the power stroke, the exhaust is already open and the inlet is closed. The spark comes before top dead centre, once every two turns; for starting, the impulse coupling gives a late spark, after top dead centre. Total volume is swept plus clearance, and the compression ratio is total divided by clearance. Finally, power is torque times RPM.
Piston engine
Oil and cooling: what the gauges tell you Topic Rule to remember Oil jobs Primary: reduce friction and wear · also cool, clean, protect, act as hydraulic and indicating medium Dry sump Remote tank; scavenge pump 25–50 % bigger than the pressure pump so the sump stays dry (aerated, extra oil) Oil gauges Temperature at the pump inlet · pressure at the pump outlet · relief valve keeps pressure steady above idle Cold start High oil pressure is acceptable if it returns to normal as the oil warms; no pressure in about 30 s: shut down Air cooling Most common (light, simple, cheap); liquid is more efficient · rear cylinders run hottest CHT gauge Thermocouple on the hottest cylinder ; highest CHT with a weak (economy) mixture Cowl flaps Open for ground running, take-off and climb · closed in the descent (shock cooling) Coring, hydraulicing Coring: very cold start, close the cooler flaps · hydraulicing: pull a radial through, magnetos off
Oil temperature and pressure go together: hot, thin oil reads low pressure. Low pressure at normal temperature means trouble: land as soon as possible.
Chapter 30 · Revision and Exam Practice
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Oil and cooling questions are mostly about what a reading means. The oil’s first job is to reduce friction and wear; it also cools, cleans and protects. In a dry sump the scavenge pump has twenty-five to fifty per cent more capacity than the pressure pump, because the returning oil is aerated and there is extra oil after start, and the aim is to keep the sump dry. Oil temperature is sensed at the pressure pump inlet and pressure at its outlet. After a very cold start, a slightly high oil pressure is acceptable as long as it comes back to normal as the oil warms. Air cooling is the most common; the rear cylinders run hottest, so the single cylinder head temperature probe goes on the hottest one, and the highest head temperatures come with a weak mixture. Cowl flaps are open on the ground and in the climb, closed in the descent.
Piston engine
Magnetos: switching, faults and starting Dual ignition: two magnetos, two plugs per cylinder; no battery needed Switch in the primary : OFF = closed = primary earthed ; ON = open Broken earth (P) lead: magneto stays live ; the engine runs on normally with the switch off Impulse coupling: spring flicks the magnet: strong, retarded spark ; flyweights freed by centrifugal force Capacitor across the points stops arcing; dead-cut at idle, drop check at about 75 % RPM Plug fouling: low power and over-rich mixture, e.g. climbing without leaning Magneto primary circuit iron core, rotating magnet primary: few turns secondary: thousands EHT → distributor → plugs points capacitor switch All three are in parallel across the primary, to earth primary circuit Switch position and result OFF switch CLOSED: primary earthed, no spark ON switch OPEN: the points break the current, spark P-lead broken cannot be earthed: magneto LIVE, runs on START impulse coupling: strong spark, after TDC
Chapter 30 · Revision and Exam Practice
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ignition block has one idea that catches people: off means closed. The ignition switch sits in the magneto primary circuit, in parallel with the contact breaker points. Switch off, and the switch closes, earthing the primary, so the points can no longer interrupt the current and no spark is made. Switch on, and the switch opens, letting the points work. So if the earth lead breaks, the magneto cannot be switched off: the engine keeps running normally with the switch at off, and every propeller must be treated as live. For starting, the impulse coupling holds the magnet back, then a spring flicks it round: a strong spark, and a late one, after top dead centre, so the engine does not kick back. Once the engine runs, centrifugal force keeps the flyweights clear. Plugs foul with carbon at low power and with over-rich mixtures, for example in a climb without leaning.
Piston engine
Avgas, detonation and mixture strength 100LL blue , 100 green , 80 red · octane rating = anti-knock value Detonation: end gas explodes after the spark · pre-ignition: hot spot fires it before Chemically correct 15 : 1 by mass; best power about 12.5 : 1; take-off about 10 : 1 Weak mixture: economy, but highest CHT ; rich at high power to stop detonation Climbing: air density falls, so the mixture control reduces fuel flow Piston EGT gauge: used to set the mixture (peak EGT near 15 : 1) Power and EGT against mixture (illustrative) 8 : 1 10 : 1 12 : 1 14 : 1 16 : 1 18 : 1 20 : 1 40 60 80 100 Air : fuel ratio by mass (← rich · weak →) Per cent of peak best power 12.5 : 1 peak EGT 15 : 1 power EGT take-off 10 : 1 Mixture rules · Rich at high power: spare fuel cools the charge, no detonation · Weak for economy: lowest fuel use, but the highest CHT · Climbing: density falls, so the mixture lever reduces fuel flow
Chapter 30 · Revision and Exam Practice
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fuel and mixture. Avgas one hundred L L is blue, one hundred is green, eighty is red, and the octane rating measures anti-knock value, nothing else. Detonation happens after the spark, when the unburnt end gas explodes; pre-ignition happens before the spark, from a hot spot. The chart shows the classic mixture curves. The chemically correct ratio is fifteen to one by mass, and that is where the exhaust gas temperature peaks. Best power comes a little rich, around twelve and a half to one, and take-off uses about ten to one, the spare fuel cooling the charge and holding off detonation. Weak mixtures save fuel but run the cylinder heads hottest. As you climb the air thins and a carburettor richens, so the mixture control is used to reduce the fuel flow. And on a piston engine the exhaust gas temperature gauge exists to help the pilot set the mixture.
Piston engine
Carburettors, induction icing and injection Venturi depression meters fuel by airflow ; the mixture control trims the fuel flow Icing from about −7 °C to +33 °C with high humidity: well above +10 °C , no cloud needed Cooling up to about 22 °C, mostly fuel evaporation; worst at low power Signs: fixed pitch RPM drop ; constant speed MAP drop Carb heat: full, long enough; costs about 15 % power, richer mixture; never for take-off Injection: no venturi, so no refrigeration ice; impact ice still possible When can carburettor ice form? -10 +0 +10 +20 +30 +40 0 25 50 75 100 Outside air temperature (°C) Relative humidity (%) icing possible −7 to +33 °C, humid air +10 °C is not a limit for carburettors −7 +33 Recognise and clear it · Fuel evaporation cools the air up to about 22 °C; worst at low power · Fixed pitch: RPM drops · constant speed: MAP drops · Full carb heat: rough at first, RPM then rises if ice was there
Chapter 30 · Revision and Exam Practice
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Carburettor icing is examined as numbers. Fuel evaporation and the venturi can cool the induction air by about twenty-two degrees, so ice can form at outside temperatures from about minus seven to plus thirty-three degrees when the air is humid. The chart shows that window. Notice that plus ten degrees is not a limit at all: icing is quite possible on a warm, humid day in clear air, and no visible moisture is needed. That plus ten figure belongs to turbine engine anti-icing, a different rule. Icing is worst at low power with the throttle partly closed. A fixed-pitch propeller shows it as an RPM drop; with a constant-speed propeller the manifold pressure falls. Use full heat for long enough; it costs about fifteen per cent of the power and richens the mixture. A fuel-injected engine has no venturi, so no refrigeration ice, but impact ice can still block the intake.
Piston engine
Power, altitude and supercharging Power follows mass of charge : best in cold, dry, high-pressure air Turbo: exhaust turbine drives the compressor; closing the waste gate sends more gas through it Waste gate seized shut in the descent: denser air → MAP over the limit (over-boost) Full throttle height: less boost → higher FTH; less RPM → lower FTH Supercharger output = MAP; an intercooler cuts charge temperature and detonation NA engine: MAP falls about 1 inHg per 1000 ft Power against altitude (ISA, constant RPM) 0 4000 8000 12000 16000 20000 40 60 80 100 120 Pressure altitude (ft) Power (% of sea-level NA) FTH at rated boost 8000 ft less boost: FTH ≈ 12500 ft normally aspirated Turbocharger waste gate · Gate closing: more exhaust through the turbine, more boost · Seized shut in a descent: denser air, MAP over the limit · Best power: cold, dry, high-pressure air
Chapter 30 · Revision and Exam Practice
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
A piston engine’s power follows the mass of charge it burns. So the best performance comes in cold, dry air at high pressure; humid air carries less oxygen. A normally aspirated engine loses about one inch of manifold pressure every thousand feet. A turbocharger uses an exhaust-driven turbine; the waste gate controls it, and closing the gate sends more exhaust through the turbine. If the waste gate seizes closed, the danger is in the descent: the air gets denser and the manifold pressure can exceed its limit. The chart is computed from the standard atmosphere. At rated boost the supercharged engine holds its power up to the full throttle height, where the throttle is wide open; above it, power falls like a plain engine. Climb at less than rated boost, and the throttle reaches fully open higher up: a lower boost gives a higher full throttle height.
Propellers
Blade angle, angle of attack and twist Blade angle β: chord to plane of rotation · angle of attack α: chord to relative airflow α = β − helix angle φ; φ grows with TAS, shrinks with RPM Twist (wash-out) root to tip: keeps α about the same and thrust even along the blade Fixed pitch accelerating down the runway: α decreases Constant speed: TAS ↑ → blade angle ↑, α stays about the same Turboprop torque measured in the reduction gearbox , between engine and propeller Fixed blade angle, rising TAS: α falls Early in the take-off run rotation 180 m/s TAS 30 chord β 25° α 15.5° φ 9.5° Faster: helix angle larger rotation 180 m/s TAS 70 chord β 25° α 3.7° φ 21.3° α = β − φ Twist: β falls from root to tip (V 60, tip 240 m/s, α 4°) r = 0.3 R β 44° r = 0.6 R β 27° r = 0.9 R β 20°
Chapter 30 · Revision and Exam Practice
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Propeller questions rest on two angles. The blade angle is measured from the plane of rotation to the chord. The angle of attack is measured from the relative airflow to the chord, and the relative airflow comes from combining the rotational speed with the forward speed. The two triangles are computed for one blade section turning at a fixed speed. At low forward speed the helix angle is small and the angle of attack is large; at higher speed the helix angle grows and, with a fixed blade angle, the angle of attack falls. That is what happens to a fixed-pitch propeller on the take-off run. A constant-speed propeller coarsens instead, keeping the angle of attack roughly constant. The blade is twisted, with the angle reducing from root to tip, because the tip moves faster: twist keeps the angle of attack similar and the thrust even along the blade.
Propellers
The constant-speed unit, feathering and the pitch ranges Situation What the governor does On speed Flyweight force = speeder spring; pilot valve covers the port; oil trapped, blade angle held Overspeed Weights fly out, valve moves, blades coarsen , RPM returns Underspeed Weights fall in, oil directed to decrease the blade angle (fine), RPM returns TAS or power increases Blade angle increases to hold RPM; α roughly constant Alpha range Feather to the flight fine pitch stop : governed, in flightBeta range Flight fine stop to reverse : ground only, pitch set directly by the power lever Feathering Blades edge-on: drag windmilling > stopped > feathered; unfeather with an accumulator or pump Levers Power up: mixture, RPM, then MAP · power down: MAP, then RPM
Fixed pitch: α rises with RPM and falls with TAS. Constant speed: the governor changes β so that RPM, and roughly α, stay constant.
Chapter 30 · Revision and Exam Practice
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The constant-speed unit is a balance. On speed, the flyweight force equals the speeder spring force, the pilot valve covers the port and the blade angle is held. If the propeller overspeeds, the weights fly out and the blades coarsen until the RPM falls back. In an underspeed the weights fall in and oil is directed to fine off the blades, a smaller blade angle, so the RPM rises again. So when true airspeed or power increases, the blade angle increases. The pitch ranges are a favourite trap. The alpha range runs from feather to the flight fine pitch stop and is used in flight, under the governor. The beta range runs from the flight fine stop into reverse, on the ground, with pitch set directly. Feathered blades give the least drag. And remember the lever order: to increase power, mixture, RPM, then throttle; to reduce, throttle first.
Gas turbines
Spools, bypass and the gas through the engine Thrust = ṁ (Vjet − Vin ); power is changed by fuel flow alone Single spool: compressor and turbine at the same speed · multi-spool: LP turbine drives the LP compressor (fan) Bypass ratio = external (cold) ÷ internal (hot) mass flow Free turbine: drives the output shaft, no mechanical link to the compressor Highest gas temperature in the combustion chamber ; the turbine sets the limit Highest pressure at compressor delivery; theoretical air/fuel ratio 15 : 1 Along a two-spool engine (per cent of each maximum) 0 25 50 75 100 Per cent of maximum inlet fan/LPC HPC exit comb. exit HPT exit LPT exit nozzle max pressure max temperature velocity pressure temperature velocity Which turbine drives what fan HP comp. combustor HPT LPT LP shaft: LPT drives the fan (slowest) HP shaft: fastest BPR = cold ÷ hot mass flow
Chapter 30 · Revision and Exam Practice
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The gas turbine block. Thrust is mass flow times the change in velocity, and the pilot changes the power by changing the fuel flow; the airflow follows. In a single-spool engine the compressor and turbine are on one shaft and turn at the same speed. In a two- or three-spool engine, each turbine drives its own compressor: the low pressure turbine drives the low pressure compressor and fan, and the high pressure spool turns fastest. The bypass ratio is the cold, external flow divided by the hot, internal flow. A free turbine drives only the output shaft, with no mechanical connection to the compressor. The chart follows the gas through the engine. Pressure peaks at compressor delivery. Temperature peaks in the combustion chamber, but what limits it is the turbine, which must survive the gas. And chemically correct combustion is about fifteen to one, just like a piston engine.
Gas turbines
Inlets and compressors Centrifugal: air in axially at the eye , out at the tip ; diffuser: V ↓, p ↑, T ↑ Axial stage = rotor, then stator ; about 1.1–1.2 : 1 per stage Axial vs centrifugal: more mass flow , higher overall ratio, but more prone to damage Stall at low RPM: variable inlet guide vanes , bleed valves, multi-spool Loose blade roots seat under centrifugal and aerodynamic forces when running Subsonic intake is divergent : V ↓, p ↑ before the fan Centrifugal compressor: eye, impeller tip, diffuser exit 150 450 120 1 2 4 15 110 175 eye impeller tip diffuser exit velocity (m/s) pressure (bar) temperature (°C) Axial stage: rotor, then stator rotor V ↑ p ↑ T ↑ stator V ↓ p ↑ T ↑ air 1.1–1.2 : 1 per stage Axial vs centrifugal: more air, higher ratio more easily damaged Low RPM stall: VIGVs, bleed valves, spools
Chapter 30 · Revision and Exam Practice
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Compressors. In a centrifugal compressor air enters the eye axially and the impeller flings it out to the tip, raising its velocity, pressure and temperature. The diffuser then slows it down, turning that speed into more pressure, so in the diffuser velocity falls while pressure and temperature rise. The chart shows the three stations. An axial stage is a rotor followed by a stator, giving only about one point one to one point two to one each, so many stages are used. Compared with a centrifugal compressor, the axial takes in more air and reaches higher overall ratios, but its thin blades are more easily damaged by foreign objects. At low RPM the front stages tend to stall, so variable inlet guide vanes, bleed valves and multiple spools are used. Blades with loose roots tighten when running, held by centrifugal and aerodynamic forces. A subsonic intake is divergent, slowing the air before the fan.
Gas turbines
Combustion chambers and turbines Primary air about 20 % at 15 : 1 ; secondary 20 %; tertiary 60 % dilutes; overall 45–130 : 1 Primary zone about 2000 °C , the hottest gas; outlet cooled to suit the turbine Through the chamber: T ↑, V ↑, p falls slightly (3–8 %) NGVs convergent: V ↑, p ↓; along the span root to tip: p rises, V falls Blades: impulse root, reaction tip; creep = heat + centrifugal load Turbine entry temperature limited by NGV and blade materials Gas temperature along a combustion chamber 0 20 40 60 80 100 0 500 1000 1500 2000 Distance along the chamber (%) Gas temperature (°C) primary 20 % secondary 20 % tertiary (dilution) 60 % ≈ 2000 °C, 15 : 1 to the NGVs ≈ 1150 °C NGV exit, root to tip (free vortex) 0.8 R 0.9 R 1.0 R 0.8 0.9 1.0 Radius (root → tip) Relative value velocity falls pressure rises Across the NGVs: V ↑, p ↓ (convergent) Blades: impulse root, reaction tip Limit: NGV and blade materials
Chapter 30 · Revision and Exam Practice
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The hot end. Only about twenty per cent of the air is burnt with the fuel, in the primary zone, at around fifteen to one; that is where the gas is hottest, near two thousand degrees. Secondary air holds the flame steady, and the remaining sixty per cent dilutes and cools the gas before the turbine. Overall the air to fuel ratio is anything from forty-five to one hundred and thirty to one. Through the chamber temperature and velocity rise, while pressure falls slightly. In the turbine, the nozzle guide vanes are convergent: velocity up, pressure down. They also make the gas swirl, so across the span, from root to tip, the pressure rises and the velocity falls, as the lower panel shows. That is why blades are impulse at the root and reaction at the tip. The materials of the vanes and blades set the temperature limit of the whole engine.
Gas turbines
Thrust, EPR and engine temperatures F = ṁ (Vj − Va ) + Ae (pe − p0 ); maximum thrust at standstill EPR = turbine outlet (jet pipe) ÷ compressor inlet total pressure TIT/TGT before the turbine (hottest) · EGT in the jet pipe , after the turbines Power set by EPR or N1 (fans), torque (turboprops) Cold, dense air: more thrust · thrust falls more slowly than pressure with height Convergent nozzle chokes at Mach 1: extra pressure thrust Thrust against speed (sea level, constant RPM) 0 100 200 300 400 0 25 50 75 100 True airspeed (kt) Thrust (% of static) turbojet (fast jet) high-bypass fan (slow jet) static thrust (0 kt) is the maximum F = ṁ (Vj − Va): ram raises ṁ, but Vj − Va shrinks Where it is measured inlet compressor combustor turbines jet pipe P inlet TIT (hottest) EGT P jet pipe EPR = P jet pipe ÷ P inlet Turboprop torque: in the reduction gearbox
Chapter 30 · Revision and Exam Practice
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Thrust and its measurement. Thrust is mass flow times the velocity change, plus a pressure term if the nozzle is choked. The chart is computed from that equation. As the aircraft speeds up, the velocity change shrinks, while ram effect raises the mass flow. In a turbojet, with its fast jet, ram nearly makes up the loss, so thrust falls only slowly. In a high-bypass fan, with a slow jet, thrust falls much faster. Either way static thrust is the maximum. Engine pressure ratio is the jet pipe pressure, after the turbine, divided by the compressor inlet pressure. Turbine inlet temperature is measured before the turbine and is the most critical; exhaust gas temperature is measured downstream, in the jet pipe. Fans set power with E P R or N one, turboprops with torque, measured in the reduction gearbox.
Gas turbines
Performance, bleed air and reverse thrust Topic Rule to remember Best performance Low temperature, low humidity, high pressure: dense air Bleed valve opened EPR and thrust fall, EGT rises , SFC rises; the same for anti-ice and pack bleedHP bleed Opens at low power and for anti-ice; LP stage feeds in normal flight Extra accessory load More power off-take: SFC increases Water / methanol Restores mass flow hot and high; methanol burns and restores turbine temperature Reverser types Clamshell and bucket turn the hot gas · blocker doors turn the cold fan stream Reverser light Amber when the doors are unlocked (away from stowed), not merely when selected Using reverse Weight on wheels, idle first; reverse idle by 60–80 kt to avoid re-ingestion
Bleed taken from the compressor has already absorbed turbine work but bypasses the turbine: less work for thrust, so more fuel for the same RPM, hence the higher EGT.
Chapter 30 · Revision and Exam Practice
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
This page gathers turbine performance, bleed and reverse. Like any engine, the turbine performs best in dense air: cold, dry and at high pressure. Open a bleed valve and you take compressed air away before it can do work in the turbine. To hold the speed the fuel control adds fuel, so the exhaust gas temperature rises, while the engine pressure ratio and thrust fall, and specific fuel consumption goes up. That applies to anti-ice and air conditioning bleed too. Any extra accessory load also raises specific fuel consumption. Water injection restores mass flow on a hot day, and methanol in it burns, putting the temperature back. Reversers: clamshell and bucket types turn the hot gas, blocker doors turn the cold fan air. The amber reverser light comes on when the doors are unlocked, out of the stowed position, not just when reverse is selected.
Gas turbine systems
Oil, gearboxes, ignition and starting Topic Rule to remember Oil system Dry sump, synthetic oil; one pressure pump, up to six scavenge pumps (larger : keep sumps dry) Fuel-cooled oil cooler Heats the fuel, cools the oil ; oil pressure kept above fuel pressureChip detectors Magnets in the scavenge lines: early warning of bearing failure Gearbox Driven from the HP spool ; fuel, oil and hydraulic pumps, generators, starter pad Ignition High-energy capacitor discharge: HE for start and relight, LE for continuous; 60–100 sparks a minute Starting Starter turns the HP spool ; self-sustaining about 30 % N2; idle about 60 % N2, 25 % N1 Start faults Hot: fuel off · hung: high EGT, low RPM · wet (no light-up): motor with the HP cock shut APU Constant speed turboshaft: electrics and bleed on the ground and in flight; auto shut-down for fire and limits
Oil is checked shortly after shut-down. High oil temperature with the cooler air inlet blocked; a short run-down with high oil use points to a seal rub.
Chapter 30 · Revision and Exam Practice
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The engine systems in one table. The turbine oil system is a dry sump with synthetic oil: one pressure pump and up to six scavenge pumps, which together have more capacity so the bearing sumps stay dry. The fuel-cooled oil cooler does two jobs at once: it heats the fuel and cools the oil, with the oil at higher pressure so a leak goes oil into fuel. Chip detectors in the scavenge lines catch bearing failures early. The accessory gearbox is driven from the high pressure spool, which is also what the starter turns. Ignition is a capacitor discharge: high energy for starting and relight, low energy for continuous use. In a normal start the engine becomes self-sustaining around thirty per cent N two and idles near sixty. A hot start means fuel off now; a hung start shows high EGT with low RPM.
Gas turbine systems
The turbine fuel system, in order Fuel flows left to right booster pumps in the tanks LP valve (firewall) fire handle LP pump feeds HP pump FCOC cools oil fuel heater before filter filter ice crystals HP pump HP spool FCU meters fuel HP cock fuel switch flow- meter mass flow nozzles atomise LAST unit low pressure supply conditioning high pressure, metering, delivery Which valve, which job · HP cock: fuel switch OFF, the normal shut-down · LP valve: closed by the fire handle, at the firewall · Heater before the filter: frozen water can block it · FCOC: heats the fuel, cools the oil (oil pressure higher) · Flowmeter: mass flow, from the fuel’s momentum Turbine fuels · Jet A-1: kerosene, SG ≈ 0.80, flash ≈ +38 °C, wax ≈ −50 °C · Jet A: as Jet A-1 but waxes at −40 °C (USA) · Jet B: wide-cut, SG ≈ 0.77, flash ≈ −20 °C · Undyed: straw to clear · cloudy sample: water · FSII stops free water freezing; heaters on the engine Normal shut-down: HP cock (fuel switch OFF). Fire: the fire handle closes the LP valve at the firewall. The flowmeter is the last unit before the nozzles.
Chapter 30 · Revision and Exam Practice
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The turbine fuel system is examined as an order, so learn this line. Booster pumps in the tanks push fuel to the low pressure valve at the firewall, which the fire handle closes. The engine-driven low pressure pump keeps the high pressure pump well fed. Next the fuel-cooled oil cooler and the fuel heater warm the fuel, and the heater is placed before the filter so that ice crystals from dissolved water cannot block it. Fuel heaters are on the engine, not in the tanks. Then the high pressure pump, driven by the high pressure spool, the fuel control unit, and the high pressure cock, which the fuel switch closes for a normal shut-down. Last of all, just before the nozzles, comes the flowmeter, which measures mass flow by the momentum of the fuel. Below the line are the turbine fuel facts: grades, densities and the cloudy sample.
The rest of the paper
Airframe and flight controls Topic Rule to remember Loads and fatigue Design limit load 2.5 g (ultimate 3.75 g) · fatigue life counted in cycles, so a long-haul type is not used short-haul Structure Stressed skin: bending taken by spars and skin (non-stressed: spars) · torsion box: spars, skin, stringers, ribs Stringers, materials Stringers support the skin and carry pressurisation strain as tension · Duralumin: Al–Cu, hard to weld, conducts heat well Wing bending relief Wing fuel used last , aileron up-float · T-tail sits out of the wing downwash Ailerons Inboard (all-speed) only with flaps up : less wing twist at high speed · differential ailerons equalise drag Surfaces Krueger flaps: inboard leading edge · flaperons: flap + aileron · spoilers: upper surface, symmetric or asymmetric Powered controls Irreversible: needs artificial feel, fitted in parallel · trim tab: holding force to zero · two trim switches against runaway Wing anti-ice Hot bleed air in the wing leading edges and slats , not the flaps
Chapter 30 · Revision and Exam Practice
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The general knowledge paper mixes in airframe questions, so here they are in one table. The design limit load of a transport aircraft is two point five g, with an ultimate load of three point seven five. Fatigue life is counted in pressurisation cycles, which is why a long-haul aircraft is not simply used on short sectors. In a stressed-skin wing the spars and skin carry the bending; with a non-stressed skin the spars do it all. The torsion box is spars, skin, stringers and ribs, and stringers carry pressurisation strain as tension. Wing bending is relieved by burning wing fuel last. Inboard ailerons are used alone at high speed to avoid twisting the wing, so only the inboard ailerons work with the flaps retracted. Differential ailerons equalise drag. Krueger flaps sit on the inboard leading edge. Artificial feel is connected in parallel with an irreversible control system.
The rest of the paper
Hydraulics, landing gear and tyres Phosphate ester: purple , synthetic, harms eyes and skin, can still burn; about 3000 psi Reservoir pressurised by engine bleed air ; fluid temperature taken in the reservoir Fuse closes if a brake line bursts · shuttle valve: two supplies, one service · RAT: flight controls Down and locked = over-centre lock, three greens · torque links keep the wheel aligned · mountings: cantilever, fork, half fork, dual Under-inflation wears the shoulders · aquaplaning: friction ≈ 0 · fusible plugs in the wheel · retread several times Autobrake disengaged by the pilot; torque links worst in tight taxi turns Pascal: the Bramah press 10 N 100 N 0.05 m² 0.5 m² p = 10 ÷ 0.05 = 200 Pa · F = 200 × 0.5 = 100 N Hydraulic valve and its electrical twin One-way check valve diode: flow one way only Shuttle valve changeover: two supplies, one service Hydraulic fuse fuse: shuts off flow if a line bursts Accumulator stores energy, like a capacitor
Chapter 30 · Revision and Exam Practice
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Hydraulics and landing gear. Modern airliners use phosphate ester fluid, which is purple and synthetic, harmful to eyes and skin; typical pressure is three thousand psi. The reservoir is pressurised by engine bleed air, to stop the pump cavitating. The press on the right is the classic calculation: ten newtons on point zero five square metres is a pressure of two hundred pascals, and on half a square metre that gives one hundred newtons. Below, each valve has an electrical twin: a check valve behaves like a diode, a shuttle valve like a changeover relay. A hydraulic fuse closes when a line bursts. The ram air turbine powers the flight controls. The gear is locked down by an over-centre strut, and three greens mean down and locked. Under-inflated tyres wear on the shoulders, a tyre that is aquaplaning has almost no friction, and the fusible plugs sit in the wheel rim.
The rest of the paper
Air conditioning and pressurisation Topic Rule to remember Bootstrap order Primary heat exchanger → compressor → secondary heat exchanger → turbine → water separator Why compress first Bigger pressure and temperature drop across the turbine ; ground fan draws air over the heat exchangers Vapour cycle Refrigerant Freon ; the condenser turns gas into liquid Control and ceiling The outflow valve controls pressure · ceiling: max differential with the cabin at its max altitude Outflow fails open Cabin rate of climb up, cabin altitude up , differential down Outflow fails shut Cabin VSI shows descent; differential rises to max, then the safety valve opens Decompression Cabin VSI up , cabin altitude up , differential down · warning at 10 000 ft Negative differential Inward relief valve opens · ditching control closes the outflow valves
Rule of thumb: cabin pressure and differential move together; cabin altitude moves the other way. Falling cabin pressure = the cabin VSI shows a climb.
Chapter 30 · Revision and Exam Practice
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Air conditioning and pressurisation follow a few rules. In the bootstrap pack, air goes through the primary heat exchanger, then the compressor of the cold air unit, then the secondary heat exchanger, then the turbine, with the water separator after the turbine. Compressing first gives a bigger pressure and temperature drop across the turbine. On the ground a fan draws cooling air over the heat exchangers. A vapour cycle uses Freon, and the condenser turns the refrigerant from gas to liquid. The outflow valve controls the cabin pressure. If it fails open, the cabin climbs and the differential falls. If it fails shut, the cabin descends, the differential rises to the maximum and the safety valve opens. In a decompression the cabin rate shows a climb, cabin altitude rises and the differential falls. Below outside pressure, the inward relief valve opens.
The rest of the paper
Ice protection and fire protection Topic Rule to remember Ice systems Jets: hot air · turboprops: pneumatic boots (mechanical, de-icing only) · electric: small areas (probes, screens) Screens and detectors Heated windscreen: ice and bird strike · vibrating probe works by accretion Fire wire With heat, resistance falls, capacitance rises ; warning when both loops sense heat at any point Warning and detectors Individual red light + common bell · smoke: optical or ionisation , toilets and cargo B, C, E · overheat in wheel baysEngine bottle Fired by the pilot after shut-down; the handle shuts the LP valve and trips GCB and exciter Agents Flight deck: Halon · brakes and gas fires: dry powder · magnesium: sand · fuel spills: foam Hand-held count 31–60 seats 2 · 61–200 3 ; at least 2 BCF in the cabin from 61 seats, plus a halon unit on the flight deck Crash axe Flight deck (more than 9 seats); a second above 200 seats · for access behind panels to fight fire
Melting-link detectors cannot reset; a capacitive wire short gives no false warning; a resistive short does.
Chapter 30 · Revision and Exam Practice
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ice and fire. Airliners use hot bleed air for wing and engine anti-icing, turboprops use pneumatic boots, which can only de-ice, and electrical heating is kept for small areas such as probes and windscreens. A heated windscreen resists both ice and bird strike, and the vibrating probe detector senses ice by accretion. In a fire wire, heat makes the resistance fall and the capacitance rise; with two loops, both must sense heat for a warning. The engine fire warning is an individual red light with a common bell. Smoke detectors are optical or ionisation types, in toilets and class B, C and E cargo holds. The pilot fires the engine bottle once the engine is shut down. For agents: halon on the flight deck, dry powder on brakes and gas fires, sand on magnesium. And from sixty-one seats, three hand extinguishers in the cabin.
The rest of the paper
Oxygen: systems and requirements Topic Rule to remember Crew system Gaseous, diluter-demand : flows on inhalation, diluted with cabin air · smoke: select EMERGENCY Passenger system Chemical: self-contained and light, cannot be switched off · doors: electric (chemical), pneumatic (gaseous) Safety and layout Over-pressure: bursting disc vents the cylinder overboard · two independent systems, crew and cabin Pressurised: passengers 100 % above 15 000 ft, at least 10 min · masks = seats + 10 % · first aid: 2 %, at least 1, above 8000 ftPressurised: crew Above 13 000 ft; 10–13 000 ft after 30 min; at least 30 min (certified ≤ 25 000 ft) or 2 h above Unpressurised Crew above 10 000 ft; cabin crew and 10 % of passengers after 30 min at 10–13 000 ft; all above 13 000 Masks and briefing One pilot wears a mask above FL 410 · above FL 250: oxygen briefing before take-off Smoke hood Full face, continuous oxygen flow from its own generator
Chapter 30 · Revision and Exam Practice
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Oxygen is a page of rules. The crew use gaseous oxygen through a diluter-demand regulator: it flows only when you breathe in, diluted with cabin air at lower altitudes, and with smoke you select emergency for a hundred per cent under positive pressure. Passengers usually have chemical generators: self-contained and light, but they cannot be turned off. Their mask doors open electrically for chemical systems and pneumatically for gaseous ones. An over-pressurised cylinder vents its whole contents overboard through a bursting disc. In a pressurised aircraft all passengers need oxygen above fifteen thousand feet, for at least ten minutes, and there must be ten per cent more masks than seats. First aid oxygen covers two per cent of passengers, at least one, above eight thousand feet cabin altitude. Above flight level four one zero one pilot wears a mask.
The rest of the paper
Exits, slides and survival equipment Topic Rule to remember Assisted escape Sill more than 1.83 m (6 ft) above ground, with the nose gear collapsed Slides Inflated by their own gas bottle · armed door opened from outside : slide disarmed , stays stowed Life jackets Beyond 50 nm from land, or over water on take-off and landing Life rafts Can fly on one engine: beyond 120 min or 400 nm , whichever is less · others 30 min or 100 nm Raft capacity Room for everyone even if the largest raft is lost Beacons Survival beacon battery 48 h Worked example 60 on board, 240 kt, 2 h from land: 480 nm > 400 nm → rafts; three 30-seat rafts and 60 life jackets Second example 150 kt one-engine speed: 120 min = 300 nm; at 340 nm from land: life jackets and rafts
Chapter 30 · Revision and Exam Practice
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Emergency equipment questions are mostly arithmetic on a few rules. An exit needs an assisted means of escape if its sill is more than one point eight three metres, six feet, above the ground with the nose gear collapsed. Slides inflate from their own gas bottle; an armed door opened from outside disarms itself, so the slide stays stowed. Life jackets are needed beyond fifty nautical miles from land. Rafts: an aircraft able to continue on one engine needs them beyond one hundred and twenty minutes at cruising speed or four hundred nautical miles, whichever is less. At one hundred and fifty knots that is three hundred miles, so an aircraft three hundred and forty miles out needs rafts and jackets. And the rafts must hold everyone even with the largest lost: sixty people with thirty-seat rafts means three rafts. The survival beacon lasts forty-eight hours.
The rest of the paper
Aircraft fuel systems and gauging Baffles stop sloshing ; baffle check valves stop fuel running to the tip ; feeder (surge) box keeps the pump inlet covered Boosters: centrifugal , low pressure, AC induction motors (115/200 V three-phase) Tanks pressurised by ram air through the vents · pressure refuelling: the bowser pumps VTO shuts the inlet valve at the set level (refuel or transfer); jettison stops at a preset safe quantity Capacitance: dielectric changes capacitance ; reads mass; water → full scale high Cross-feed: any tank to any engine · bond before caps off · fill tanks after the last flight Capacitance gauge: reading against depth 0 20 40 60 80 100 0 25 50 75 100 Depth of liquid in the probe (%) Gauge reading (% of full) water: full scale at only 1.4 % depth fuel (K ≈ 2.1) Dielectric constant: air 1, fuel ≈ 2.1, water ≈ 80 Compensated: it reads mass Fuel warms: volume × 1.05, density ÷ 1.05 Mass = volume × density = 8000 lb, unchanged · Power failure: pointer drifts to empty · Float gauge: simple, but reads volume only · Cloudy sample: water; drain, fill tanks after flight
Chapter 30 · Revision and Exam Practice
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aircraft fuel systems. Baffles stop the fuel sloshing, and their check valves let it flow inboard but not out to the wing tip, while a feeder or surge box keeps the pump inlets covered and stops cavitation. Booster pumps are centrifugal low pressure pumps driven by three-phase AC motors. Tanks are vented, and pressurised slightly, by ram air. Airliners are pressure refuelled, the bowser doing the pumping, and the volumetric top-off unit shuts the fuelling valve at the set level. Jettison stops at a preset safe quantity; it is required when the maximum landing mass is well below the take-off mass. The chart explains the capacitance gauge. Fuel has a dielectric constant of about two, air one, water about eighty. So a tank with water in it reads full scale high. Because the gauge is compensated, warm fuel that expands five per cent still reads the same mass.
The rest of the paper
Electrics and radio in eight lines Topic Rule to remember Busbars Loads in parallel : current falls as loads go off · hot bus: always on the battery · changeover relay: alternate source to an essential bus Protection Fuse non-resettable, CB resettable · current limiter: high melting point , slow · relay = electrically operated (magnetic) switch Batteries Check on load ; nearly flat: voltage and current fall, worse with load · one dead cell: unserviceable · nicad: compact, long shelf life, flat voltage Wiring Earth return: negatives to the structure ; lighter, easier fault finding, more shorts · poor bonding: radio static AC basics 400 Hz ; f = pole pairs × rev/s; three phases 120° apart · inverter DC → AC (instruments) · series motor for startersGenerators GCB: generator to its own load bus · over-excitation or fire handle: GCB + exciter relay trip · load ↑: excitation ↑ Paralleling, CSD Real load: CSD torque · reactive load: voltage / excitation · CSD overheat: disconnect, reset only on the ground Theory and logic Parallel: 1/RT = Σ 1/R · capacitive circuit: f ↑ → current ↑ · AND = all or nothing gate · DC regulator: parallel armature, series field
Radio: λ (m) = 300 ÷ f (MHz): 121.95 MHz → 2.46 m. VHF and VOR are metric, ADF hectometric. HF skip grows with frequency and layer height: longest at night on a high frequency.
Chapter 30 · Revision and Exam Practice
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The last subject block is electrics, with a few radio facts. Loads on a busbar are in parallel, so switching loads off reduces the current. A hot battery bus is connected to the battery at all times. Fuses cannot be reset; circuit breakers can. Check a battery on load; one dead cell makes a lead-acid battery unserviceable. In an earth-return system the negative terminals go to the structure, and poor bonding shows up as radio static. Aircraft AC runs at four hundred hertz, and frequency is pole pairs times revolutions per second: six thousand RPM is one hundred per second, so four pole pairs give four hundred hertz. The generator breaker connects a generator to its own bus. In parallel running, real load is shared by drive torque and reactive load by excitation. For radio, wavelength in metres is three hundred over the frequency in megahertz.
Classic traps
Where marks are lost Carb icing Up to about +33 °C in humid air; +10 °C is the turbine anti-ice rule, not a carburettor limit.
Off means closed Magneto OFF = primary earthed . A broken earth lead leaves it live .
Which α? Fixed pitch on the take-off run: α falls . Constant speed: β rises , α about the same.
Alpha and beta Alpha: feather to flight fine stop. Beta: flight fine to reverse, ground only.
Bleed valve open EPR down , thrust down , EGT up , SFC up .
Where measured EPR: jet pipe ÷ inlet. EGT: jet pipe . Torque: reduction gearbox . Flowmeter: last , before nozzles.
Hottest vs limit Hottest gas: combustion chamber . What limits it: the turbine .
Two valves Normal stop: HP cock . Fire handle: LP valve . Heater: on the engine, before the filter.
Chapter 30 · Revision and Exam Practice
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
These are the places where marks are lost on the powerplant paper. Carburettor icing reaches up to about plus thirty-three degrees in humid air; plus ten is the turbine anti-ice rule. A magneto is switched off by earthing its primary, so a broken earth lead leaves it live. With a fixed-pitch propeller the angle of attack falls as speed builds; with a constant-speed propeller the blade angle rises instead. The alpha range runs from feather to the flight fine stop. Opening a bleed valve lowers E P R and thrust but raises EGT. Know where each quantity is measured: E P R across the engine, EGT in the jet pipe, torque in the reduction gearbox, fuel flow last before the nozzles. The hottest gas is in the combustion chamber, but the turbine sets the limit. And the HP cock is for a normal stop, the LP valve for fire.
Method and summary
How to answer, and your last-minute list 1 · Read the stem Underline NOT, EXCEPT, first, normally, most likely. Many wrong options are true about a different case.
2 · Which engine? Piston, turbojet, fan or turboprop? Fixed or constant speed? The same word means different things.
3 · Follow the flow Trace the air, gas, fuel or oil in order. The answer is usually “before” or “after” something.
4 · Check the units Mass or volume, absolute or gauge, kt or nm, Hz or RPM. Write the formula, check the size.
Piston numbers 720° · 15 : 1 · 12.5 : 1 power · 10 : 1 take-off · ice −7 to +33 °C · 1 inHg per 1000 ft.
Turbine numbers Primary 20 % at 15 : 1 · 2000 °C · SSS 30 % N2 · idle 60 % N2 · HE 60–100 sparks per minute.
Systems numbers 2.5 g · 3000 psi · 1.83 m · 50 nm · 120 min / 400 nm · 10 000 / 13 000 / 15 000 ft.
Electrics numbers 400 Hz · 120° phases · 115/200 V · 28 V DC · 300 ÷ MHz = metres.
Chapter 30 · Revision and Exam Practice
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Finish with a method, then the list. First, read the stem and underline not, except, first and normally, because many wrong options are true statements about a different case. Second, decide which engine or which propeller the question is about; the same word can mean different things on a piston engine and a turbofan. Third, follow the flow: air, gas, fuel or oil, in order. Many answers are simply before or after something. Fourth, check the units, mass or volume, absolute or gauge, hertz or RPM. Then the last-minute numbers: seven twenty degrees, fifteen to one, twelve and a half to one for power, carburettor ice from minus seven to plus thirty-three. Twenty per cent primary air, thirty per cent N two self-sustaining, sixty per cent idle. Two point five g, three thousand psi, four hundred hertz. Now go to the questions.