Engines · Chapter 21
Thrust Where jet thrust comes from, how it changes with RPM, altitude, temperature and speed, and how the crew measure and set it.
THRUST
F = ṁ (Vj − Va)
air in, Va
jet out, Vj
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter twenty one is about thrust: what it really is, and why the same engine, at the same throttle setting, gives a different amount of it on a hot day, at high altitude or at high speed. We will build the thrust equation from Newton's laws, separate momentum thrust from pressure thrust, and work out examples with real numbers. Then we will see how thrust changes with RPM, altitude, temperature and airspeed, how ram recovery helps, and how a turboprop behaves. Finally we look at how the crew measure and set power, with the engine pressure ratio, exhaust temperatures and the torquemeter.
Roadmap
Thrust: where it comes from and what changes it 1 · The equation Momentum and pressure thrust, ram drag, gross and net thrust, worked examples.
2 · Output and economy ESHP for turboprops, specific fuel consumption, thrust ratings.
3 · What changes thrust RPM, altitude, temperature, airspeed, ram recovery, flat rating, turboprop SHP.
4 · Measuring it EPR, TIT, EGT and JPT, thermocouples, the torquemeter, and how power is set.
Chapter 21 · Thrust
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for this chapter. In part one we build the thrust equation: thrust as mass flow times change in velocity, plus a second term, pressure thrust, that appears when the nozzle is choked, and the idea of ram drag that separates gross from net thrust. In part two we look at output and economy: equivalent shaft horsepower for turboprops, specific fuel consumption, and the named thrust ratings. Part three is the heart of the exam questions: how thrust and fuel consumption change with RPM, altitude, temperature and airspeed, why ram recovery matters and what flat rating means. In part four we see how the crew actually measure and set power, using the engine pressure ratio, the exhaust temperatures and the torquemeter.
Part 1 · The thrust equation
Thrust is a reaction Newton's second law: force = mass × acceleration ; per second of flow, F = ṁ (Vj − Va) Newton's third law: the engine pushes the gas back , the gas pushes the engine forward ṁ : mass of air per second; Va : inlet (flight) velocity; Vj : jet velocityThrust needs mass flow and acceleration : anything that cuts either cuts thrust The jet does not "push on the air behind": it would work in a vacuum
Va
Vj
Thrust (reaction)
Action on the gas
Thrust = ṁ × (Vj − Va)
F = m × a, per second of flow
Chapter 21 · Thrust
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Thrust is simply a reaction. Newton's second law says force equals mass times acceleration. For an engine that handles a steady stream of air, we use the mass that passes each second, the mass flow, and the change in its velocity, so thrust equals mass flow times the jet velocity minus the inlet velocity. Newton's third law tells us the direction: the engine pushes the gas backwards, so the gas pushes the engine forwards. Watch the velocity graph under the engine. The air comes in at the inlet velocity, which in flight is the aircraft's speed, slows a little in the intake and combustor, then leaves the nozzle as a fast jet. Two things matter: how much air, and how much it is speeded up. A common misconception is that the jet pushes against the air behind it. It does not; a jet would work even in a vacuum.
Part 1 · The thrust equation
The full equation: momentum thrust plus pressure thrust
The control volume
ṁ, Va
p₀ ambient
ṁ, Vj
pₑ, Aₑ
dashed: what goes in and out per second
Two parts of thrust
Momentum thrust
ṁ (Vj − Va)
+
Pressure thrust (choked nozzle only)
Aₑ (pₑ − p₀)
ṁ mass flow (kg/s) Va flight speed
Vj jet velocity Aₑ nozzle exit area
pₑ exit static pressure p₀ ambient
In a convergent nozzle that is not choked , the gas leaves at ambient pressure and the second term is zero.
Chapter 21 · Thrust
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the full thrust equation. Imagine a box drawn round the engine and count what crosses it each second. Air enters at mass flow m dot and flight speed V a, and leaves at the jet velocity V j. The change of momentum gives the first term, momentum thrust, mass flow times V j minus V a. Fuel adds a percent or two to the mass, which we usually ignore. The second term appears only when the nozzle is choked. Then the gas leaves at the speed of sound with a static pressure still above the ambient pressure, and that pressure difference acting over the nozzle exit area gives an extra push: pressure thrust, the exit area times the exit pressure minus the ambient pressure. So for a turbojet running choked, total thrust is momentum thrust plus pressure thrust. If the nozzle is not choked, the gas expands to ambient pressure inside it and pressure thrust is zero.
Part 1 · The thrust equation
Gross thrust, ram drag and net thrust Gross thrust = ṁ × Vj (plus any pressure thrust)Ram drag (intake momentum drag) = ṁ × Va: the momentum the air already hadNet thrust = gross thrust − ram dragStanding still, Va = 0: net = gross , so static thrust is the maximum Worked example: 100 kg/s, Vj 500 m/s: 50 kN static; at 200 m/s, 30 kN net
ṁ = 100 kg/s, Vj = 500 m/s
0
10
20
30
40
50
60
kN
50
50
Va = 0 m/s
50
30
ram drag
20
Va = 200 m/s
gross thrust ṁVj
net thrust
Chapter 21 · Thrust
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
It helps to split the thrust equation into two parts. Gross thrust is the mass flow times the jet velocity, plus any pressure thrust. Ram drag, also called intake momentum drag, is the mass flow times the flight speed: it represents the momentum the air already had before the engine touched it. Net thrust is gross thrust minus ram drag. Let us put numbers in. An engine swallows one hundred kilograms a second and sends it out at five hundred metres a second. Standing on the brakes, the flight speed is zero, so there is no ram drag and the net thrust is fifty kilonewtons. Now fly at two hundred metres a second with the same jet velocity. Gross thrust is still fifty, but ram drag is one hundred times two hundred, twenty kilonewtons, leaving thirty net. This is why the maximum thrust any jet engine can develop is its maximum static thrust.
Part 1 · The thrust equation
Pressure thrust from a choked nozzle A convergent nozzle chokes when the pressure ratio across it exceeds about 1.85 (hot gas) Gas leaves at Mach 1 ; it cannot expand fully inside the nozzle Exit static pressure pₑ > p₀ : the excess pressure pushes on the exit area Pressure thrust = Aₑ (pₑ − p₀) , added to momentum thrust At high altitude p₀ is low, so pressure thrust is a larger share of the total
Choked convergent nozzle
throat: M = 1
Gas reaches the speed of sound at the exit
and cannot expand fully inside the nozzle
Example: Aₑ = 0.25 m², pₑ − p₀ = 60 kPa
Pressure thrust = 0.25 × 60 000 = 15 000 N
= 15 kN on top of the momentum thrust
Chapter 21 · Thrust
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does a choked nozzle give extra thrust? A convergent nozzle speeds the gas up until, at the exit, it reaches the speed of sound. Once the pressure ratio across the nozzle is above about one point eight five for hot gas, the nozzle is choked: the exit velocity cannot rise any further, and the gas leaves at a static pressure still higher than the surrounding air. It finishes its expansion outside the nozzle, where it can no longer push on the engine directly, but the pressure difference across the exit area does push forward on the engine. That is pressure thrust. Worked example: an exit area of nought point two five square metres, with the exit pressure sixty kilopascals above ambient, gives fifteen thousand newtons, fifteen kilonewtons, of pressure thrust on top of the momentum thrust. At altitude, where the ambient pressure is low, this term becomes a bigger share of the total.
Part 1 · The thrust equation
A big mass slowly, or a small mass fast? Same thrust either way: 100 kg/s × 600 m/s = 600 kg/s × 100 m/s = 60 kN But the kinetic energy left in the jet is ½ṁ(ΔV)² : 18 MW against 3 MW Low-bypass turbojet: small mass, large acceleration , high jet velocity, noisy, wasteful at low speed High-bypass turbofan and turboprop: large mass, small acceleration , better propulsive efficiency Both change with density, temperature and airspeed : the rest of this chapter
Small mass, large acceleration
Large mass, small acceleration
100 kg/s × 600 m/s = 60 kN
energy left in the jet: ½ṁV² = 18 MW
Vj − Va = 100
600 kg/s × 100 m/s = 60 kN
energy left in the jet: 3 MW
Chapter 21 · Thrust
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two ways to make the same thrust. You can give a small mass of air a large acceleration, or a large mass of air a small one. One hundred kilograms a second speeded up by six hundred metres a second gives sixty kilonewtons; so does six hundred kilograms a second speeded up by only one hundred. The difference is the energy wasted. Whatever kinetic energy is left in the jet behind the aircraft is lost, and it goes with the square of the velocity change: eighteen megawatts in the first case, only three in the second. That is why the low-bypass turbojet, with its fast, noisy jet, is wasteful at subsonic speeds, while the high-bypass turbofan, whose big fan moves a huge mass of bypass air gently, and the turboprop do far better. In the scene, see the fan, the bypass air and the small, fast core jet.
Part 2 · Output and economy
Turboprops: SHP and equivalent shaft horsepower A turbojet's output is thrust , shown by EPR (or a P7) gauge A turboprop's output is shaft horsepower (SHP) , shown by a torquemeter It also leaves some jet thrust in its exhaust ESHP = SHP + jet thrust expressed as horsepower Static rule of thumb: 1 SHP ≈ 2.5 lbf of thrust Example: 2000 SHP + 500 lbf ÷ 2.5 = 2200 ESHP
Turboprop output
0
500
1000
1500
2000
horsepower
2000 SHP
shaft
2200 ESHP
equivalent
Jet thrust 500 lbf ÷ 2.5 = 200 hp
ESHP = SHP + jet thrust as horsepower
Chapter 21 · Thrust
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
A turbojet's output is thrust, and the pilot reads it on an engine pressure ratio gauge, or on older engines a jet pipe pressure gauge. A turboprop is different. Its turbine extracts most of the gas energy to drive the propeller through a reduction gearbox, so its output is shaft horsepower, read on a torquemeter. But the exhaust still leaves with some velocity, so there is a little jet thrust too. To compare engines fairly, we add that jet thrust to the shaft power and call the total the equivalent shaft horsepower. Under static conditions, one shaft horsepower is roughly equal to two and a half pounds of thrust. Worked example: an engine delivering two thousand shaft horsepower, with five hundred pounds of jet thrust in its exhaust, has two thousand plus two hundred, that is two thousand two hundred equivalent shaft horsepower.
Part 2 · Output and economy
Specific fuel consumption SFC = fuel flow ÷ thrust (or ÷ SHP): fuel used per hour per unit of output Units: lb/h per lbf for jets; lb/h per SHP for turboprops The lower the SFC, the more economical the engine Set by thermal efficiency × propulsive efficiency High bypass ratio and high pressure ratio both lower SFC
SFC = fuel flow ÷ output
Engine
Output
Fuel flow
SFC
High-bypass turbofan
5 000 lbf
2 750 lb/h
0.55
Turbojet
5 000 lbf
4 500 lb/h
0.90
Turboprop
2 000 SHP
1 000 lb/h
0.50
Jets: lb of fuel per hour per lb of thrust
Turboprops: lb per hour per shaft horsepower
Lower SFC = more economical engine
Chapter 21 · Thrust
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
To judge how economical an engine is, we do not look at fuel flow alone, because a bigger engine naturally burns more. We use specific fuel consumption: the fuel used per hour for each unit of output. For a jet it is pounds of fuel per hour per pound of thrust; for a turboprop, pounds per hour per shaft horsepower. Look at the examples. A high-bypass turbofan making five thousand pounds of thrust on two thousand seven hundred and fifty pounds of fuel an hour has an S F C of nought point five five. A turbojet needing four thousand five hundred pounds an hour for the same thrust has nought point nine: much worse. A turboprop of two thousand shaft horsepower burning one thousand pounds an hour has nought point five. Specific fuel consumption depends on how well the engine turns heat into gas energy, its thermal efficiency, and how well it turns that into thrust, its propulsive efficiency.
Part 2 · Output and economy
Thrust ratings Rating What it means Maximum static thrust The greatest thrust the engine can develop: standing still, no ram drag Take-off thrust Maximum thrust for take-off, normally time-limited (e.g. 5 minutes) Go-around thrust May equal take-off thrust, but is normally a lower value Maximum continuous thrust May be used without a time limit ; for emergencies such as engine failure Maximum climb thrust Equivalent to max continuous on many engines; gives the best-angle climb speeds Maximum cruise thrust Set below max continuous to prolong engine life
Higher ratings mean higher turbine temperatures; time limits protect the hot section.
Chapter 21 · Thrust
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Engines are given a ladder of named thrust ratings, each with its own limits. At the top, the greatest thrust any jet can develop is its maximum static thrust, standing still with no ram drag; exam questions like this answer. Take-off thrust is the maximum for take-off, and it is normally time-limited, typically to five minutes, because of the high turbine temperatures. Go-around thrust may be the same as take-off thrust, but is normally a lower value. Maximum continuous thrust can be used for as long as needed, for example after an engine failure. Maximum climb thrust is equivalent to maximum continuous on many engines and gives the best angle of climb speeds. Maximum cruise thrust is set below maximum continuous to prolong engine life. The pattern is simple: the higher the rating, the hotter the turbine runs and the shorter the time allowed.
Part 3 · What changes thrust
Thrust and RPM: most of it comes at the top
Thrust against fan speed (N1)
Thrust against HP speed (N2)
0
20
40
60
80
100
0
25
50
75
100
N1 % (y: % take-off thrust)
25% N1 ≈ 5% thrust
40
50
60
70
80
90
100
0
25
50
75
100
N2 %
ground idle 50–60%
half the thrust above ≈ 85%
Computed: thrust ∝ N12.16 (fitted so that 25% N1 ≈ 5%) and ∝ ((N2 − 50)/50)². In flight, idle RPM is higher than on the ground because of bleed and generator loads.
Chapter 21 · Thrust
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Thrust rises with RPM, because a faster compressor swallows more air, but not in a straight line. On the left is thrust against fan speed, N 1. At twenty five per cent N 1 a big fan gives only about five per cent of its take-off thrust. A favourite exam question: a fan with a maximum of twenty thousand RPM, turning at five thousand, is at twenty five per cent, so it gives about five per cent take-off thrust. On the right is thrust against HP spool speed, N 2. At ground idle on a twin spool engine the HP spool turns at about fifty to sixty per cent and the LP spool about twenty five per cent. The curve is so steep at the top that about half the thrust comes in the last fifteen per cent of HP RPM, above roughly eighty to eighty five per cent. In flight, idle RPM is higher than on the ground, because of the power taken off for bleed air and generators.
Part 3 · What changes thrust
Spooling up: why the lever and the thrust are not in step From idle, the spools must accelerate before mass flow and thrust build The fuel control limits fuel during acceleration to avoid surge and over-temperature Because thrust ∝ roughly RPM², the first part of the lever travel gives little thrust On a go-around from flight idle , spool-up takes several seconds: idle is set higher in flight partly for this reason The LP spool (N1) is slower and lags the HP spool (N2)
Slam from ground idle
0
2
4
6
8
10
0
25
50
75
100
Seconds after the lever moves
%
95% thrust after 7.5 s
N2
N1
thrust
Illustrative spool lags: HP leads, LP and thrust follow
Chapter 21 · Thrust
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
When you push the thrust levers forward from idle, the thrust does not appear at once. Fuel flow rises first, the extra heat speeds up the turbines, and only as the spools accelerate does the mass flow, and with it the thrust, build up. The fuel control deliberately limits how fast fuel is added, because too much fuel too early would make the compressor surge or overheat the turbine. Remember also that thrust rises roughly with the square of RPM, so the first part of the lever movement gives very little thrust. That is why a go-around from a low idle takes several seconds to reach full power, and one reason why flight idle is set higher than ground idle. Watch the engine accelerate: the HP spool, in bronze, leads, and the bigger, slower LP spool with the fan, in blue, follows behind it.
Part 3 · What changes thrust
Thrust and altitude
0
10,000
20,000
30,000
40,000
50,000
0%
25%
50%
75%
100%
Altitude (ft)
Ratio to sea level
tropopause
−56.5 °C from here up
thrust (≈ density)
pressure alone
At 30 000 ft, ISA
pressure ratio 30%
density ratio 37%
Cold air partly offsets
the fall in pressure, so
thrust falls more slowly
than pressure alone.
Above the tropopause the
temperature stops falling:
thrust falls faster.
At a fixed throttle the fuel control's altitude capsule trims fuel to the falling mass flow, holding RPM. Thrust and fuel flow fall together, so SFC stays essentially the same .
Chapter 21 · Thrust
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
As an aircraft climbs, both pressure and temperature fall. Falling pressure lowers the density, so the engine swallows less mass and thrust falls. But falling temperature raises the density, which partly makes up for it. The result is that thrust falls with altitude, but more slowly than it would if pressure alone were falling. The graph is computed from the standard atmosphere: at thirty thousand feet the pressure is about thirty per cent of sea level, but the density, which roughly tracks thrust, is about thirty seven per cent. Above the tropopause, at about thirty six thousand feet, the temperature stays at minus fifty six point five, so there is no help from the cold any more and thrust falls faster. Meanwhile the fuel control's altitude capsule reduces fuel flow to match the smaller airflow, holding the RPM constant. Thrust and fuel flow fall together, so the specific fuel consumption stays essentially the same.
Part 3 · What changes thrust
Thrust and air temperature Colder air is denser : more mass per revolution, so more thrust But the compressor then has more work to do: more fuel is needed to hold RPM, or it slows down Warmer air is less dense : mass flow and thrust fall The compressor then speeds up unless fuel flow is reduced Hot day + high airfield = the worst take-off case
Cold day
Hot day
density ↑
mass flow ↑
thrust ↑
RPM tends to fall:
FCU adds fuel
density ↓
mass flow ↓
thrust ↓
RPM tends to rise:
FCU cuts fuel
Same RPM, different air
Chapter 21 · Thrust
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Temperature affects thrust through density. On a cold day the air is denser, so at the same RPM the compressor takes in more mass, and thrust goes up. There is a catch: pumping more mass is harder work, so to keep the compressor at the same speed the fuel control must add fuel, or the compressor would slow down. The exam phrase is: as temperature decreases, density increases, mass flow increases, thrust increases, and more fuel must be added or the compressor will slow down. On a hot day it is the other way round. The air is thinner, mass flow and thrust fall, and because the compressor has less work to do it tends to speed up unless the fuel flow is reduced. Put a high airfield and a hot day together and you have the worst case for take-off thrust. That is the problem that water injection, in the next chapter, was designed to solve.
Part 3 · What changes thrust
Flat rating: the same take-off thrust up to a set temperature
-20
-10
0
10
20
30
40
50
60
80
100
120
Outside air temperature (°C)
% rated take-off thrust
flat-rate temperature
dashed: available if not limited
part throttle: lever short of full travel
temperature limited
Flat rating
Below the flat-rate temperature
the engine is limited by the
maximum compressor pressure
(power limiter): rated thrust is
reached early, before full lever.
Above it, the turbine
temperature limit takes over
and thrust falls as OAT rises.
Illustrative: rated thrust 100% up to a flat-rate temperature of 30 °C (often about ISA + 15), then falling about 0.9% per °C.
Chapter 21 · Thrust
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a cold day the dense air would let the engine produce more thrust than its structure is designed for. The limit here is the maximum pressure the compressor may deliver, which a power limiter enforces. So on cold and moderate days the engine reaches its rated take-off thrust before the throttle lever reaches the end of its travel, well before the turbine temperature limit. Such engines are called part throttle, or flat-rated, engines: the take-off thrust can be achieved at throttle settings below full throttle, so on a part throttle engine take-off thrust is achieved earlier than normal. The rated thrust is flat, the same, all the way up to the flat-rate temperature, often about I S A plus fifteen. Above that, the turbine temperature becomes the limit, and the available thrust falls as the outside air gets hotter. The graph shows the flat line, and the dashed line of what the engine could give if it were not held back.
Part 3 · What changes thrust
Thrust and airspeed
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
Flight Mach number
Ratio to the static value
dip, then ram recovery
ram drag only (no ram recovery)
ram pressure ratio → mass flow
net thrust
Fixed throttle, sea level
Ram drag (ṁ × Va) grows with
speed, so thrust first falls.
Ram pressure in the intake then
raises mass flow and recovers
part of the loss.
Net thrust never quite regains
its static value: maximum thrust
is static thrust.
Computed model: mass flow ∝ (1 + 0.2M²)3.5 , jet velocity rising slightly with ram, net thrust = ṁ (Vj − Va). As mass flow rises, fuel flow rises too, so SFC increases with speed.
Chapter 21 · Thrust
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
What happens to thrust as the aircraft speeds up, with the throttle fixed? Look at the thrust equation: if the jet velocity stays about the same and the inlet velocity rises, the difference gets smaller, and thrust falls. The dashed line shows that effect on its own. But forward speed also rams air into the intake, raising the pressure at the compressor face and with it the mass flow; that is the blue line. Put the two together and you get the real net thrust curve: from a standing start it falls, reaches a dip, and then partly recovers as ram pressure builds, but it never quite gets back to its static value. Remember the exam answer: from a standing start, with increasing forward speed, jet thrust decreases, then recovers, but never achieves its initial value. Because the extra mass flow needs extra fuel while the net thrust is lower, specific fuel consumption gets worse as speed increases.
Part 3 · What changes thrust
Ram recovery The subsonic intake is a divergent duct : it slows the air and turns velocity into pressure Higher pressure at the compressor face = more mass flow for the same RPM This restores part of the thrust lost to ram drag Ram pressure is zero at the start of the take-off run , when thrust is greatestAbove Mach 1 a specially shaped supersonic intake is needed
Subsonic intake = diffuser
compressor
face
fast
slower
velocity ↓
pressure ↑
Chapter 21 · Thrust
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ram recovery is how the engine claws back some of the thrust that ram drag takes away. A subsonic intake is shaped as a divergent duct, a diffuser. As the air flows through it, it slows down, and the energy of its velocity is turned into pressure. So at speed, the pressure at the compressor face is higher than outside. Look at the pressure trace under the engine: it already rises a little in the intake, before the compressor adds its much bigger rise. A higher pressure at the face means denser air, so the compressor moves more mass at the same RPM, and part of the lost thrust is restored. At the very start of the take-off run there is no ram pressure at all, and that is also where thrust is greatest; so thrust is maximum and ram pressure minimum when the brakes are released. Above Mach one, a specially designed supersonic intake is needed.
Part 3 · What changes thrust
The turboprop: altitude and airspeed
Climbing (altitude ↑)
Accelerating (TAS ↑)
0
5,000
10,000
15,000
20,000
25,000
0.0
0.5
1.0
Altitude (ft)
SHP ↓
jet thrust and fuel flow ↓
SFC ≈ constant
0
50
100
150
200
250
300
0.0
0.5
1.0
TAS (kt)
SHP ↑ (ram)
jet thrust ↓
SFC ↓ (fuel flow ↑)
Illustrative curves. Climbing: SHP ↓, jet thrust ↓, fuel flow ↓ , SFC ≈ same. Accelerating: SHP ↑, jet thrust ↓ , fuel flow ↑, SFC ↓.
Chapter 21 · Thrust
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
A turboprop follows the same physics, but the exam asks about it separately. As it climbs, density falls, so it suffers a loss of power just like the jet: shaft horsepower falls, the net jet thrust falls, so the equivalent shaft horsepower falls, and the fuel flow falls with them. Specific fuel consumption stays essentially the same. So a turboprop with a fourteen stage axial compressor, while climbing, experiences decreasing shaft horsepower, decreasing jet thrust and decreasing fuel consumption. Now let it accelerate. Ram pressure in the intake raises the mass flow, so the shaft horsepower increases. The small jet thrust, however, falls, because the gas leaves at a speed not much greater than the flight speed. Fuel burn rises with the extra mass flow, but the power rises faster, so specific fuel consumption goes down. Increasing speed: shaft horsepower up, jet thrust down.
Part 3 · Summary of effects
What changes, and which way Change (fixed lever) Thrust or SHP Fuel flow SFC RPM up Up, steeply near the top Up Best near high RPM Altitude up (to tropopause) Down (slower than pressure) Down About the same Above the tropopause Down faster Down About the same Colder air Up (more fuel to hold RPM) Up Slightly better Jet: airspeed up Down, dips then partly recovers Up (ram mass flow) Up Turboprop: airspeed up SHP up, jet thrust down Up Down Turboprop: climbing SHP, jet thrust, ESHP down Down About the same
Chapter 21 · Thrust
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are all the effects together, for a fixed throttle lever. More RPM gives more thrust, very steeply near the top of the range. Climbing to the tropopause, thrust falls, but more slowly than pressure, because the cold air is denser; fuel flow falls with it and S F C stays about the same. Above the tropopause thrust falls faster. Colder air gives more thrust, but the control has to add fuel to hold RPM. For a jet, increasing airspeed first reduces thrust, then partly recovers it with ram, while fuel flow and S F C rise. For a turboprop, increasing airspeed raises shaft horsepower thanks to ram, while jet thrust falls and S F C improves. And climbing in a turboprop, shaft horsepower, jet thrust and fuel flow all fall, while S F C stays about the same. If you can reproduce this table, you can answer most of the thrust questions in the exam.
Part 4 · Measuring thrust
Engine pressure ratio (EPR) EPR = turbine exhaust total pressure ÷ compressor inlet total pressure Written Pt5/Pt2 (or P7/P1 in older numbering): LP turbine outlet ÷ LP compressor inlet Thrust depends on the pressure rise through the engine, so EPR is a thrust meter Used to set power on turbojets and many turbofans ; others use N1 Turboprops set power with torque , not EPR
EPR = Pt5 ÷ Pt2
Pt2
Pt5
compressor inlet
turbine exhaust
1.45
162 kPa ÷ 112 kPa
= EPR 1.45
Chapter 21 · Thrust
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
The engine pressure ratio is the jet engine's thrust meter. It is the total pressure at the turbine exhaust, behind the LP turbine, divided by the total pressure at the compressor inlet. With the station numbers shown on the engine, that is P t five divided by P t two; older engines and some textbooks number them P seven over P one, but it is the same idea: LP turbine outlet pressure divided by LP compressor inlet pressure. Since thrust depends on how much the engine raises the pressure of the gas that then expands through the nozzle, this ratio is closely related to thrust. Worked example: one hundred and sixty two kilopascals behind the turbine, divided by one hundred and twelve at the inlet, gives an E P R of one point four five. E P R is used to set power on turbojets and many turbofans; other turbofans use N 1. Turboprops set power with torque.
Part 4 · Measuring thrust
EPR exam traps A blocked inlet (Pt2) probe , e.g. by ice, reads too low : the EPR gauge over-indicates Danger: the crew set a "correct" EPR while the engine gives less thrust than they think Use engine anti-ice as required and cross-check N1 During the take-off run at a fixed lever, ram raises Pt2 more than Pt5: EPR decreases slightly EPR is not a temperature or fuel-flow reading
Inlet probe blocked
Take-off run, fixed lever
True: 162 ÷ 101 = 1.60
Ice traps a low Pt2, say 90 kPa:
162 ÷ 90 = 1.80 on the gauge
EPR over-reads; the crew set
less real thrust than they think
Brakes off: 162 ÷ 101 = 1.60
At 150 kt ram adds ≈ 3.7 kPa to Pt2
Pt5 rises less: 164 ÷ 105 = 1.56
EPR falls a little as speed builds
(FADEC or the crew trim it back)
Chapter 21 · Thrust
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two classic E P R traps. First, if the inlet probe that senses P t two becomes blocked, for example by ice, it no longer sees the true inlet pressure and typically reads too low. Since that pressure is the bottom of the fraction, the E P R gauge over-indicates. In the example, a true one point six becomes one point eight on the gauge. The real danger is that the crew set the take-off E P R they want, while the engine is actually producing much less thrust. Cross-checking N 1 against the other engines catches it. Second, during the take-off run with the levers fixed, ram pressure raises the inlet pressure. At one hundred and fifty knots that is nearly four kilopascals, but the turbine exhaust pressure rises proportionally less, so E P R falls a little, from one point six to about one point five six in our example. As a jet accelerates down the runway, its E P R decreases.
Part 4 · Measuring temperature
TIT, EGT and JPT TIT (turbine inlet temperature, or TGT): upstream of the HP turbine , the hottest and most criticalTIT is often too hot to measure directly: measured between turbines or further aft and computed EGT (exhaust gas temperature): downstream of the LP turbine JPT (jet pipe temperature): in the jet pipe All guard the turbine blades : limits are highest for short periods (start, take-off)
TIT / TGT
turbine entry: hottest
EGT
after the LP turbine
JPT
in the jet pipe
TIT is often too hot to measure: taken further aft and computed
Chapter 21 · Thrust
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Exhaust temperatures are the second key engine reading, because they protect the turbine. The turbine inlet temperature, sometimes called turbine gas temperature, is measured upstream of the HP turbine, at the turbine entry. It is the hottest and most critical temperature in the engine, and often too hot to measure reliably, so it is usually measured further aft, between turbines, and the turbine entry value is computed. The exhaust gas temperature is measured downstream of the LP turbine, and the jet pipe temperature in the jet pipe. Look at the temperature trace: it peaks in the combustor and at the turbine entry, then falls through each turbine stage as energy is taken out. So the common set of names for upstream of the HP turbine, downstream of the LP turbine and in the jet pipe is T I T, E G T and J P T.
Part 4 · Measuring temperature
Thermocouples in parallel Exhaust temperature is sensed by thermocouples : a junction of two dissimilar metals (chromel–alumel) gives a voltage that rises with temperature Several probes are spaced round the jet pipe , because the gas is hotter in some places than others They are wired in parallel , so the gauge shows the average temperature If one probe fails, the reading changes only slightly No external power is needed: the thermocouple makes its own voltage
Probes in parallel
jet pipe
640
°C EGT
Red dots: hot junctions (chromel–alumel)
Parallel harness = the AVERAGE temperature
One failed probe barely changes the reading
Chapter 21 · Thrust
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Exhaust temperature is measured with thermocouples. A thermocouple is a junction of two different metals, typically chromel and alumel. When the hot junction in the gas stream is hotter than the cold junction at the instrument end, it produces a small voltage that rises with the temperature difference, so it needs no electrical supply of its own. The gas leaving the turbine is not equally hot all the way round; some burners run hotter than others. So several probes are spaced round the jet pipe, and they are connected in parallel. Wired in parallel, the voltages average out, and the gauge shows the average temperature. A bonus of the parallel connection is that if one probe fails, the reading changes only slightly. In the exam, the jet pipe temperature is measured by a number of thermocouples connected in parallel.
Part 4 · Measuring turboprop power
The torquemeter Turboprop power is torque × RPM ; RPM is held constant by the propeller governor, so torque sets power A hydraulic torquemeter sits in the reduction gearbox The helical ring gear is held from turning: torque makes it press axially against oil pistons The oil pressure needed to hold it is proportional to torque Example: 5000 N·m at 1200 rpm = 628 kW ≈ 840 SHP
Hydraulic torquemeter
helical ring gear
(held from turning)
axial thrust
oil piston
TQ %
Power = torque × RPM
5 000 N·m at 1 200 rpm = 2π × 20 × 5 000
= 628 kW ≈ 840 SHP
Chapter 21 · Thrust
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
A turboprop's power is torque times RPM. Because the propeller governor holds the RPM constant, the pilot sets power by setting torque. A common design is the hydraulic torquemeter in the reduction gearbox. In the epicyclic gear train, the outer ring gear has helical teeth and is held so that it cannot turn. The torque being transmitted tries to turn it, and because the teeth are helical, it also pushes the ring gear sideways, along the axis. Small pistons with oil behind them hold it in place, and the oil pressure needed to do that is proportional to the torque, so a gauge of that pressure reads torque. Worked example: five thousand newton metres at twelve hundred RPM is two pi times twenty revolutions a second times five thousand, which is six hundred and twenty eight kilowatts, about eight hundred and forty shaft horsepower. Remember, torque is measured at the reduction gearbox.
Part 4 · Setting power
Which gauge sets power? Turbojet Power set with EPR (older engines: jet pipe pressure, P7). Limits watched on EGT /TGT and RPM.
Turbofan Power set with EPR , or with N1 on some types. Never with N3, EGT or fuel flow.
Turboprop Power set with torque (at constant propeller RPM); limits on TGT or ITT.
Chapter 21 · Thrust
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
So which gauge sets power? On a turbojet, power is set with E P R, or on older engines with jet pipe pressure, because those are the readings closest to thrust. Exhaust temperature and RPM are watched as limits, not used to set power. On a turbofan, power is set with E P R on many engines, and with N 1, the fan speed, on others; never with N 3, exhaust temperature or fuel flow, which do not track thrust well enough. On a turboprop, the propeller governor holds RPM constant, so power is set with torque, while the turbine gas temperature, or the inter-turbine temperature, is watched as a limit. Exam questions like to swap these around, so learn them as a set: turbojet E P R, turbofan E P R or N 1, turboprop torque.
Summary
What to take into the exam Equation F = ṁ(Vj − Va) + Aₑ(pₑ − p₀). Net = gross − ram drag. Maximum thrust is static thrust.
ESHP and SFC ESHP = SHP + jet thrust (1 SHP ≈ 2.5 lbf static). SFC = fuel per hour per unit output; lower is better.
RPM 25% N1 ≈ 5% thrust. Ground idle N2 50–60%, N1 ≈ 25%. Most thrust above 80–85% N2.
Altitude Thrust ↓ more slowly than pressure; faster above the tropopause. Fuel flow ↓, SFC ≈ same.
Temperature Cold: thrust ↑, more fuel to hold RPM. Flat-rated engines reach take-off thrust early , at part throttle.
Speed Jet: thrust ↓, dips, partly recovers by ram, never regains static; SFC ↑. Turboprop: SHP ↑, jet thrust ↓.
EPR and temps EPR = Pt5/Pt2; blocked inlet probe over-reads; EPR ↓ on take-off run. TIT, EGT, JPT; thermocouples in parallel.
Setting power Turbojet EPR; turbofan EPR or N1; turboprop torque , measured in the reduction gearbox.
Chapter 21 · Thrust
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Thrust is mass flow times the change in velocity, plus pressure thrust from a choked nozzle; net thrust is gross thrust minus ram drag, so the maximum thrust is static thrust. Equivalent shaft horsepower adds jet thrust to shaft power, at about two and a half pounds per horsepower, and S F C is fuel per hour per unit of output. Twenty five per cent N 1 gives about five per cent thrust, and most thrust comes above eighty to eighty five per cent HP RPM. Thrust falls with altitude, more slowly than pressure, and faster above the tropopause, while S F C stays about the same. Cold air gives more thrust; flat-rated engines reach take-off thrust early, at part throttle. With speed, jet thrust dips and partly recovers; a turboprop gains shaft horsepower. E P R is P t five over P t two, set on jets; turboprops set torque.