Engines · Chapter 18
The Turbine Assembly How the turbine turns hot, fast gas into shaft power: nozzle guide vanes and rotor stages, impulse and reaction blading, creep, materials, blade fixing, spools, free power turbines and EGT.
rotation HP turbine disc and blades, seen from the rear © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter eighteen is about the turbine, the part of the engine that pays for everything else. Hot gas from the combustion chamber rushes through rows of nozzle guide vanes and turbine blades, and in giving up its energy it turns the shafts that drive the compressor, the accessories and, in a turboprop or helicopter, the propeller or rotor. The turbine works at the highest temperature and some of the highest stresses in the whole aircraft, so we will look at how it is built, what limits it, and the exam favourites: impulse and reaction blading, creep, fir-tree roots and the free power turbine.
Roadmap
What this chapter covers 1 · The stage NGVs then rotor blades; how pressure, temperature and velocity change; the task of the turbine.
2 · Stress and heat Tip speeds, centrifugal loads, creep, materials, cooling, shrouds and tip clearance.
3 · Blade design Impulse, reaction and impulse-reaction blades; the twist; the fir-tree root.
4 · Spools and limits Multi-spool and free power turbines, turbine losses, and EGT measurement.
Chapter 18 · The Turbine Assembly
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through the turbine. First, the turbine stage: a row of stationary nozzle guide vanes followed by a row of rotating blades, and what happens to the gas pressure, temperature and velocity as it passes through. Second, the punishing conditions the blades live in: enormous centrifugal loads, gas hotter than the melting point of the metal, and the slow stretching called creep, with the materials, cooling, shrouds and tip clearance control that let the turbine survive. Third, blade design: impulse, reaction and the impulse-reaction blade with its twist, and how blades are fixed to the disc. Finally, spools and free power turbines, the small losses a turbine suffers, and how the pilot watches the turbine temperature.
Part 1 · The stage
The task of the turbine Like an axial compressor in reverse : energy is taken out of the gas, not put in The gas brings heat , pressure and kinetic energy; all three fall as it passes through The turbine turns that energy into shaft work to drive the compressor and the accessory gearbox In a turboprop or turboshaft it also drives the propeller or rotor through a reduction gearbox In a turbojet only part of the energy is taken: the rest makes the jet Gas is slower in the combustion chamber than in the exhaust unit The turbine drives the compressor compressor combustor turbine shaft work Gas energy in: heat + pressure + velocity Shaft work out: compressor, accessories (and propeller) What is left over makes the jet
Chapter 18 · The Turbine Assembly
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The turbine is easiest to understand as an axial compressor working in reverse. The compressor puts energy into the air; the turbine takes energy out of the gas. The gas arriving from the combustion chamber carries energy in three forms: heat, pressure and kinetic energy, its velocity. As the turbine converts these into mechanical work on the shaft, all three are reduced. That shaft work drives the compressor and the accessory gearbox, and in a turboprop or turboshaft engine it also drives the propeller or the helicopter rotor through a reduction gearbox. In a turbojet the turbine takes only what the compressor and accessories need, and what is left leaves as the jet. One small point the examiners like: the gas moves more slowly in the combustion chamber than it does in the exhaust unit.
Part 1 · The stage
A turbine stage: stator first, then rotor A stage = one row of stationary nozzle guide vanes (NGVs) + one row of rotating turbine blades The order is stator → rotor : the NGVs sit in front of the blades The NGVs accelerate the gas and aim it at the right angle onto the blades One or more stages on one shaft; coupled to a compressor they form a spool Two-spool engines: the HP turbine (first, hottest) drives the HP compressor; the LP turbine drives the LP compressor or fan One turbine stage = stator, then rotor Nozzle guide vanes stationary Turbine blades rotating blade motion Gas from the combustor NGVs speed the gas up and aim it at the blades; the blades take its energy as shaft work.
Chapter 18 · The Turbine Assembly
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
A turbine stage is a pair of blade rows. First comes a row of stationary nozzle guide vanes, the stator, and then a row of rotating turbine blades, the rotor. So in a turbine the sequence is always stator, then rotor, the opposite way round from a compressor stage, where the rotor comes first. The nozzle guide vanes speed the gas up and point it at exactly the right angle onto the moving blades. A turbine can have one stage or several on the same shaft, and when that shaft is joined to a compressor the whole rotating assembly is called a spool. In a two-spool engine the high-pressure turbine sits first, in the hottest gas, and drives the high-pressure compressor; the low-pressure turbine behind it drives the low-pressure compressor or the fan.
Part 1 · The stage
Pressure, temperature and velocity across one stage Nozzle guide vanes stationary Turbine blades rotating blade motion 1 = NGV inlet 2 = between rows 3 = rotor exit 1 2 3 Static pressure (bar) 1 2 3 10 15 20 NGV rotor 19 14 10 falls in both rows Static temperature (°C) 1 2 3 1100 1200 1300 1400 NGV rotor 1317 1209 1101 falls in both rows Gas velocity, absolute (m/s) 1 2 3 0 200 400 600 NGV rotor 150 520 200 up in NGVs, down in rotor Example HP stage, 50 per cent reaction at mid-height (computed: T0 = 1600 K, 20 bar in)
Chapter 18 · The Turbine Assembly
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow the gas through one stage, using an example high-pressure stage worked out with real gas properties. In the nozzle guide vanes, no work is done, but the passages converge, so pressure energy turns into velocity: the static pressure falls from about nineteen and a half bar to about fourteen, the static temperature falls, and the gas speeds up from one hundred and fifty to over five hundred metres per second. In the rotor, the blades take energy out as shaft work: the pressure falls again, to about ten bar, the temperature falls again, and the gas leaves much slower, about two hundred metres per second. So the exam answers are: pressure, decrease then decrease; temperature, decrease then decrease; velocity, increase in the stator, then decrease in the rotor.
Part 1 · The stage
The turbine on the whole-engine graph compressor combustor turbine Pressure Temperature Velocity 1 2 3 4 4.5 5 8 (each curve scaled to its own maximum) Stations 4 (turbine entry), 4.5 (between turbines) and 5 (turbine exit).
Chapter 18 · The Turbine Assembly
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now step back and see the turbine on the graph of the whole engine. Watch the stations along the top: station four is the turbine entry, four point five lies between the turbines, and five is the turbine exit. The pressure, built up by the compressor, falls steeply across the turbines, because the turbine is where the gas gives up its energy. The temperature, highest at the combustor exit, also drops as heat is turned into work, although it is still several hundred degrees when it leaves. The velocity is the interesting one: low in the combustion chamber, it rises through the turbines and on into the jet pipe and nozzle. That is why the gas in the exhaust unit is moving faster than in the combustion chamber.
Part 1 · The stage
Nozzle guide vanes: convergent nozzles NGVs are aerofoil-shaped vanes forming convergent ducts They turn pressure energy into kinetic energy : velocity up, pressure and temperature down They turn the gas to strike the blades at the best angle, in the direction of blade travel No work is done in the NGVs: total energy is unchanged The first-stage NGVs meet the hottest gas in the engine, straight from the combustor NGVs form convergent nozzles wide throat (narrow) slow fast, turned Pressure falls Velocity rises (up to about sonic) Direction turned towards the blade motion Total energy unchanged: no work is done
Chapter 18 · The Turbine Assembly
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The nozzle guide vanes are aerofoil-shaped vanes arranged so that the space between each pair forms a convergent duct, a nozzle. As the gas squeezes through the narrowing passage it speeds up, and the energy for that comes from its pressure, so the pressure and the static temperature fall while the velocity rises, often close to the local speed of sound. At the same time the curved vanes turn the gas so it strikes the moving blades at the best angle, swirling in the direction the blades travel. Notice that no work is done here; energy simply changes form. And remember the first-stage guide vanes sit right behind the combustion chamber, so they meet the hottest gas anywhere in the engine. That is why they and the first blades decide the temperature limit.
Part 2 · Stress and heat
Speed, heat and enormous loads Blade tips can exceed 1 500 ft/s (about 460 m/s) Gas temperature in a modern engine up to about 1 700 °C Gas speed up to about 2 500 ft/s , near the local speed of sound A blade weighing 2 oz at rest can pull about 2 tons at full speed High tensile load + high temperature = creep Worked example: one HP blade disc centrifugal pull r = 0.48 m to blade CG Blade mass 2 oz = 57 g Speed 8 200 rpm Tip speed 457 m/s = 1 500 ft/s Speed at blade CG 411 m/s a = V² ÷ r ≈ 352 000 m/s² ≈ 36 000 g F = m × a ≈ 20 kN ≈ 2 tonnes Gas: up to 1 700 °C, 2 500 ft/s
Chapter 18 · The Turbine Assembly
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The turbine works in conditions that would destroy most machines. Blade tips can travel faster than fifteen hundred feet per second. The gas driving them can be as hot as about seventeen hundred degrees Celsius in a modern engine, moving at up to twenty-five hundred feet per second. Let us put a number on the load. Take a two-ounce blade, about fifty-seven grams, turning at eight thousand two hundred r p m with its centre of gravity zero point four eight metres from the axis. That point moves at about four hundred and eleven metres per second, so the acceleration towards the centre is about thirty-six thousand g, and the pull on the blade root is about twenty kilonewtons, roughly two tonnes. That huge tensile load, at red heat, is exactly what causes creep.
Part 2 · Stress and heat
Creep: the blade slowly stretches Creep : permanent elongation of the blade under tensile (centrifugal) load at high temperature The metal is stretched beyond its ability to return to its original length It happens even within all limits: every blade has a finite life Over-temperature or over-speed make it much faster Longer blades close the tip clearance and can lead to rubs and failure Creep: permanent stretch over time 0 2 4 6 8 10 0.0 0.5 1.0 1.5 2.0 Running time (thousands of hours, illustrative) Elongation (%) too hot: early failure normal life ends 1 primary 2 secondary (steady) 3 tertiary Cause: high temperature + tensile (centrifugal) load Result: blades lengthen, tip gap shrinks, finite blade life
Chapter 18 · The Turbine Assembly
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Creep is the slow, permanent stretching of a metal part that is held under a tensile load at high temperature. In a turbine blade the load is the centrifugal pull we just calculated, and the temperature is close to the limit of the alloy, so the blade very gradually gets longer and does not spring back when the engine stops. The graph shows the typical shape: a quick primary stage, a long, steady secondary stage, and finally a tertiary stage where the stretching speeds up until the blade fails. However carefully the temperature and r p m limits are respected, creep still happens, so every blade has a finite life measured in hours and cycles. Running hotter, the red curve, shortens that life dramatically. For the exam: creep is permanent elongation caused by high temperature and centrifugal, tensile, loading.
Part 2 · Stress and heat
Turbine blade materials Material or process What it gives Note High-temperature steel Early engines Severe limit on turbine temperature, so on power Nickel-based alloys Much better strength when hot The next big step Superalloys (Ni, Cr, Co, Ti, W, C …)About 1 100 °C uncooled, about 1 425 °C internally cooled Complex mixtures of many metals Powder metallurgy Powdered superalloy hot-pressed solid Fine, uniform structure Directionally solidified / single crystal castingFew or no grain boundaries: very high creep resistance Used in the most advanced engines Ceramic coatings (plasma spray)Heat barrier; protects against sulphidation corrosion Sodium in the air + sulphur in the fuel attack the metal
Because the gas turbine is a heat engine, a hotter turbine means more power and better efficiency: materials set the limit.
Chapter 18 · The Turbine Assembly
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the gas turbine is a heat engine, the hotter the turbine can run, the more power and efficiency we get, so turbine materials have driven engine progress. Early engines used high-temperature steel, which kept turbine temperatures, and so power, low. Nickel-based alloys came next, and then the superalloys, complex mixtures of nickel, chromium, cobalt, titanium, tungsten, carbon and more. A superalloy blade can take about one thousand one hundred degrees uncooled, or about one thousand four hundred and twenty-five degrees if it is cooled internally. Powder metallurgy presses powdered superalloy into a solid under heat. The most advanced engines use directionally solidified and single crystal blades. Ceramic coatings, first applied as a plasma spray, protect the blade from heat and from corrosion caused by sodium from the air reacting with sulphur from the fuel.
Part 2 · Stress and heat
Why single-crystal blades resist creep Conventionally cast equiaxed grains many grain boundaries in every direction load Directionally solidified columnar grains boundaries run along the blade, none across it load Single crystal one grain no grain boundaries at all: best creep strength load
Chapter 18 · The Turbine Assembly
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does the way a blade is cast matter so much? Ordinary casting produces a metal made of many small crystals, or grains, packed together in random directions. The boundaries between grains are the weak places: creep, cracks and corrosion tend to start there, especially the boundaries lying across the direction of the load. Directional solidification cools the blade from one end so the grains grow as long columns running along the blade, leaving almost no boundaries across the load path. Single-crystal casting goes all the way: the whole blade grows as one grain, with no grain boundaries at all. The result is a blade with extremely high creep resistance, which can run hotter and last longer. That is why single-crystal blades are used in the hottest stages of modern engines.
Part 2 · Stress and heat
Cooling the hottest blades The gas can be hotter than the melting point of the blade metal HP NGVs and blades are hollow ; compressor air flows through internal passages Air leaves through small holes and forms a cooling film over the surface Cooling raises the safe gas temperature by about 300 °C for superalloys Cost: the cooling air has bypassed combustion, a small loss of efficiency An internally cooled HP blade film of cooler air shields the surface gas Compressor air enters through the root, flows through internal passages and leaves through small holes Superalloy, uncooled about 1 100 °C Superalloy, internally cooled about 1 425 °C Hottest gas, modern engine up to about 1 700 °C
Chapter 18 · The Turbine Assembly
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a modern engine the gas entering the turbine can be hotter than the melting point of the blade alloy, so the first nozzle guide vanes and blades must be cooled. They are cast hollow, with internal passages. Air taken from the compressor enters through the blade root, winds through these passages taking heat out of the metal, and then leaves through rows of tiny holes in the surface, where it spreads into a thin film of cooler air that shields the blade from the gas. For superalloys, internal cooling raises the safe working temperature from about one thousand one hundred to about one thousand four hundred and twenty-five degrees, an increase of over three hundred degrees. The price is that this air has been compressed but not burnt, so it costs a little efficiency.
Part 2 · Stress and heat
Multi-stage turbines and blade shrouds Several stages on one shaft give more power without a bigger diameter The gas annulus diverges : blades get longer towards the rear to control velocity as the gas expands Tip shrouds link neighbouring blade tips into a ringShrouds reduce gas leakage over the tips (better efficiency) and reduce vibration Shrouded blades can be made thinner, but the shroud adds weight at the tip Three-stage turbine on one shaft casing shaft to the compressor NGV NGV NGV turbine discs tip shrouds Divergent annulus: longer blades at the rear keep the gas velocity under control as the gas expands.
Chapter 18 · The Turbine Assembly
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
This drawing shows a three-stage turbine on a single shaft, the kind used on some turboprop engines. Each stage is a row of nozzle guide vanes and a disc of blades. Adding stages lets the turbine produce more power without making its diameter bigger. Notice that the gas passage, the annulus, gets wider towards the rear, so each row of blades is longer than the one before. As the gas expands to a lower pressure its volume grows, and the larger area keeps its velocity under control. Notice too the shrouds on the blade tips. Each blade carries a small platform at its tip, and the platforms of neighbouring blades form a ring. That ring reduces the gas leaking across the blade tips, which improves efficiency, and it damps vibration.
Part 2 · Stress and heat
Tip clearance and active clearance control Gas leaking over the blade tips does no work : a direct loss Discs, blades and casing expand and contract at different rates , so the gap changes An abradable lining lets a blade cut its own track without damage Active clearance control : cool air sprayed on the turbine case shrinks it to close the gapMore effective than a lining alone, all through the flight Keeping the tip gap small Active clearance control: cool air sprayed on the case turbine casing abradable lining blade tip clearance leakage over the tip does no work Disc and blades grow fast (heat + centrifugal) Casing grows at a different rate Abradable lining blade rubs a track, not a blade Active clearance control shrinks the case in cruise Result smallest gap through the flight
Chapter 18 · The Turbine Assembly
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Any gas that slips through the gap between the blade tips and the casing passes the turbine without doing any work, so designers want that tip clearance as small as possible. The difficulty is that the disc, the blades and the casing are different masses of different metals, heating and cooling at different rates, and the blades also stretch under centrifugal load. So the gap changes through every flight. One answer is an abradable lining on the casing, a soft layer that a blade can rub into, cutting its own track without harm. A more effective answer is active clearance control. Cool air from the fan or compressor is sprayed onto the outside of the turbine case, which makes it contract and close the gap, typically in the cruise, keeping the clearance at its minimum throughout the flight.
Part 3 · Blade design
The fir-tree root The most common blade fixing on modern engines Serrations machined very accurately so the centrifugal load is shared equally When stopped the blade is a loose fit and can rock in its slot When running, centrifugal force pulls it firmly into place Blades ticking or rattling as they windmill on a windy day are normal Fir-tree root in the disc rim tip shroud platform centrifugal load disc rim each serration takes an equal share of the load Stopped: loose fit; blades rock and may tick when windmilling. Running: centrifugal force pulls the root tight in its slot.
Chapter 18 · The Turbine Assembly
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each turbine blade must be held in the disc against a pull of tonnes, at red heat. The usual method is the fir-tree root, named after its shape. The root has a series of serrations that fit matching slots in the rim of the disc, and these are machined so accurately that every serration takes an equal share of the centrifugal load. Here is an exam favourite. When the engine is stopped, the blades are a deliberately loose fit, so they rock slightly in their slots. Once the engine is running, centrifugal force pulls each root outwards and holds it firmly in place. So if you hear the blades of a stationary engine ticking or rattling as the wind turns it over, that is normal and nothing to worry about; it is not a sign of wear.
Part 3 · Blade design
Impulse, reaction and impulse-reaction blades Impulse NGV rotor p All the pressure drop in the NGVs. Rotor passages: constant area; gas only turned. Reaction NGV rotor p NGVs only turn the gas. Rotor passages converge: all the expansion is in the rotor. Impulse-reaction NGV rotor p Expansion shared between NGVs and rotor. The usual turbine blade.
Chapter 18 · The Turbine Assembly
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are three ways to share out the work between the guide vanes and the blades. In an impulse turbine, like a water wheel, all the pressure drop and expansion happen in the nozzle guide vanes, which act as nozzles. The rotor passages have a constant area, so the gas is simply turned round in the blades, and the blades are pushed by the change of direction. In a reaction turbine it is the other way round: the guide vanes only turn the gas, without changing its pressure, and the expansion happens in the rotor, whose passages converge like nozzles, so the blades are driven by the reaction, much like the lift on a wing. The impulse-reaction turbine shares the expansion between the stator and the rotor. Pure reaction blading is very rare; impulse blades are used in air starter motors.
Part 3 · Blade design
The twisted impulse-reaction blade The usual turbine blade is impulse at the root and reaction at the tip The blade is twisted : a greater angle at the tip than at the root The twist makes the gas do equal work along the whole length It sends the gas into the exhaust with a uniform axial velocity Blade speed rises with radius, so each section needs a different shape One blade, three sections Tip: reaction converging passage, less turning Mid: 50 / 50 expansion shared Root: impulse deep bucket, most turning radius increases The twist (greater angle at the tip) makes every section do equal work and leaves the gas with a uniform axial velocity.
Chapter 18 · The Turbine Assembly
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
A real turbine blade is not the same shape all the way along. Near the root it is a deep, curved bucket, an impulse section. Near the tip it is thinner, less curved and set at a greater angle, a reaction section. In between, it blends smoothly from one to the other, so the blade looks twisted. Why? The tip travels much faster than the root, because blade speed is proportional to radius. If every section had the same shape, the tip would do much more work than the root, and the gas would leave with an uneven velocity. The twist corrects this, so that the gas does equal work along the whole length of the blade and leaves the turbine with a uniform axial velocity. Remember the order: impulse at the root, reaction at the tip, greater angle at the tip.
Part 3 · Blade design
Why the root is impulse and the tip reaction Degree of reaction along the blade 0.6 0.7 0.8 0.9 1.0 0 25 50 75 100 Radius ÷ tip radius (root 0.6, tip 1.0) Reaction (%) root: 0 % (impulse) tip: 64 % reaction Gas leaving the NGVs (free vortex) 0.6 0.7 0.8 0.9 1.0 0.0 0.5 1.0 1.5 2.0 Radius ÷ tip radius Relative speed whirl velocity ∝ 1/r: greatest at the root blade speed ∝ r Computed for a hub-to-tip ratio of 0.6 with pure impulse at the root: reaction = 1 − (r_root / r)²; whirl × r = constant.
Chapter 18 · The Turbine Assembly
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
These graphs explain the twist with numbers. They are computed for a blade whose root radius is sixty per cent of its tip radius, designed in the usual way so that the gas leaving the guide vanes swirls in a free vortex, with its whirl speed times radius constant. On the left, the degree of reaction, the share of the expansion taking place in the rotor, rises from zero at the root, which is pure impulse, to about sixty-four per cent at the tip. On the right, the whirl velocity of the gas leaving the guide vanes is greatest at the root and falls towards the tip, while the blade speed rises with radius. So at the outlet of the guide vanes of an impulse-reaction turbine, the gas velocity is greatest at the root, where all the expansion has happened in the vanes.
Part 3 · Blade design
Where does the gas expand? Turbine type Expansion (pressure drop) in Rotor passage Used in Impulse Stator (NGVs) onlyConstant area: gas only turned Air starter motors ; the root of normal bladesReaction Rotor only (NGVs just turn the gas)Convergent Very rare in pure form; the tip of normal blades Impulse-reaction Both stator and rotor, not equally along the bladeChanges from root to tip Most gas turbine engines Sequence Stator → rotor in every stage NGVs are in front of the blades Opposite of a compressor stage
Exam trap: in an impulse turbine the gas expands in the stator , not the rotor; in a reaction turbine it expands in the rotor .
Chapter 18 · The Turbine Assembly
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the summary the examiners test again and again: where does the gas expand? In an impulse turbine, it expands in the stator, the nozzle guide vanes, only; the rotor passages have a constant area and just turn the gas. You find pure impulse blading in air starter motors. In a reaction turbine, it expands in the rotor only; the guide vanes just turn the gas, and the rotor passages converge. Pure reaction blading is very rare. In the impulse-reaction turbine, used in most gas turbine engines, the gas expands in both the stator and the rotor, but not to the same degree along the blade: mostly in the vanes at the root, mostly in the rotor at the tip. And in every turbine stage the order is stator, then rotor.
Part 4 · Spools and limits
More power: stages, speed and spools A bigger diameter gives more power but adds drag and centrifugal stress More stages give more power with a smaller diameter Blade efficiency rises with blade speed , but stress rises with speed squared Stronger blades are heavier, which adds stress: a vicious circle The high-bypass engine needs a smaller turbine for its thrust, easing the problem The designer's vicious circle 1.0 1.1 1.2 1.3 1.4 1.00 1.25 1.50 1.75 2.00 Mean blade speed (× original) Blade stress (× original) +21 % +44 % +69 % stress ∝ (blade speed)²: 10 % faster = 21 % more stress Ways out: more stages of smaller diameter, separate spools each at its best speed, and a high bypass ratio (smaller turbine for the thrust).
Chapter 18 · The Turbine Assembly
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
How can we get more power from a turbine? A bigger diameter would do it, but a fatter engine has more drag, and longer blades on a bigger disc suffer greater centrifugal stress. Adding stages is simpler: more power with a smaller diameter. Then there is speed. A turbine blade becomes more efficient as its speed increases, because its losses fall in proportion to the square of the mean blade speed. Unfortunately the stress rises with the square of the blade speed too. The graph shows how quickly that bites: just ten per cent more speed means twenty-one per cent more stress, and thirty per cent more speed nearly seventy per cent more. Stronger blades are heavier, which adds stress again, a vicious circle. The high-bypass engine helps: its good propulsive efficiency means a smaller turbine for the same thrust.
Part 4 · Spools and limits
The three-spool turbine combustor Fan (LP compressor) IP compressor HP compressor HP turbine IP turbine LP turbine engine centre line HP shaft: fastest IP shaft LP shaft: slowest Concentric shafts: the LP shaft runs innermost, through the IP and HP shafts
Chapter 18 · The Turbine Assembly
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Large high-bypass engines often have three spools. The high-pressure turbine, first in line behind the combustor, drives the high-pressure compressor and turns fastest of all. Behind it, the intermediate-pressure turbine drives the intermediate-pressure compressor through a shaft running inside the high-pressure shaft. At the rear, the low-pressure turbine, here with several stages, drives the fan, which is also the low-pressure compressor, and it turns slowest of the three. Its shaft is the innermost, running through the middle of the other two all the way to the front. The power from that low-pressure turbine produces almost all of the thrust, because the fan moves a huge mass of bypass air at a relatively low speed. Each spool can run at the speed that suits its own compressor best.
Part 4 · Spools and limits
The free (power) turbine A turbine not connected to any compressor : it drives only the propeller or rotor reduction gearbox It is the last turbine in the engine; the gas generator in front has its own turbine Linked to the gas generator only by the gas flow , so it finds its own best speed Propeller can be held at low rpm while taxying : less noise and brake wear Needs less starting torque : the starter turns only the gas generator Free power turbine (turboprop) Gas generator compressor + combustor + its own turbine free turbine reduction gearbox propeller exhaust No mechanical link between the free turbine and any compressor: the two are coupled only by the gas flow.
Chapter 18 · The Turbine Assembly
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
A turbine coupled to a compressor has to run at whatever speed suits that compressor. A free turbine is different: it is not connected to any compressor at all. It is the last turbine in the engine, behind the gas generator, which has its own compressor and turbine, and its shaft runs forward to drive only the propeller or rotor reduction gearbox. The only link between the gas generator and the free turbine is the flow of gas, so the free turbine can settle at its own best speed. This brings practical advantages. The propeller can be held at low r p m while taxying, cutting noise and brake wear. Starting needs less torque, because the starter only has to turn the gas generator, not the propeller as well.
Part 4 · Spools and limits
Free turbines in helicopters: the rotor brake Turboshaft engines nearly always use a free power turbine A rotor brake can hold the rotor still while the gas generator runs No rotating propeller or rotor on the ground in windy conditions : safer for people nearby Exam wording: a free power turbine has no mechanical connection with the other turbines or compressors It does not drive the fan, the LP spool or any compressor Free power turbine (turboshaft) Gas generator compressor + combustor + its own turbine free turbine reduction gearbox rotor (with rotor brake) exhaust No mechanical link between the free turbine and any compressor: the two are coupled only by the gas flow.
Chapter 18 · The Turbine Assembly
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Helicopter turboshaft engines nearly always use a free power turbine. A further advantage appears here. Because the free turbine is not joined to the gas generator, a rotor brake can be fitted to hold the rotor still while the engine is running, for example while passengers board. With the rotor or propeller stopped, the dangers of blades turning in windy conditions on the ground are removed. Watch the wording in the exam. A free power turbine has no mechanical connection with the other turbine or compressor shafts. It is the last turbine in a multiple turbine system, and it does not drive any of the spools, so it does not drive the fan, the low-pressure compressor or any other compressor. It is not driven through a clutch or a free-wheel unit either.
Part 4 · Spools and limits
Losses in the turbine The turbine is a very efficient machine: total losses about 8 % About 3.5 % : aerodynamic losses in the turbine blades About 1.5 % : aerodynamic losses in the NGVs The rest, shared about equally: tip leakage and exhaust system losses Shrouds, clearance control and smooth exhaust design attack these losses Where the 8 per cent goes Blade aerodynamic losses 3.5 % NGV aerodynamic losses 1.5 % Tip leakage 1.5 % Exhaust system losses 1.5 % Total ≈ 8 %: the turbine is about 92 % efficient Tip leakage and exhaust losses share the remaining 3 per cent roughly equally.
Chapter 18 · The Turbine Assembly
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Even working this hard, the turbine is a remarkably efficient machine. On average its losses total only about eight per cent, so roughly ninety-two per cent of the available energy is put to use. The biggest share, about three and a half per cent, is aerodynamic loss in the turbine blades themselves: friction and turbulence as the gas is turned. About one and a half per cent is aerodynamic loss in the nozzle guide vanes. The remaining three per cent or so is divided roughly equally between gas leaking over the blade tips and losses in the exhaust system. You can now see why designers fit tip shrouds, use active clearance control and take great care over the shape of the exhaust unit, which we study in the next chapter.
Part 4 · Spools and limits
Watching the turbine temperature The maximum temperature the turbine can take (NGVs and blades) limits thrust or power Exceeding it causes irreparable damage , so it is always monitored Measured by thermocouples in the gas flow: EGT , or on older engines TIT , TGT , JPT Modern engines: probes inside selected NGVs , protected from the fast gas More fuel flow, more thrust: EGT rises , and vice versa Where the gas temperature is measured compressor combustor NGV HPT LPT jet pipe TIT turbine inlet TGT between turbines EGT turbine exit JPT jet pipe Thermocouples, several probes averaged; one gauge reading Modern engines: probes inside selected NGVs, shielded from the gas More fuel flow = more thrust = higher EGT (and the reverse) Over-temperature: irreparable damage. Watch it on every start
Chapter 18 · The Turbine Assembly
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The hottest parts of the engine, the nozzle guide vanes and turbine blades, set the limit on how much thrust or power we can have. The net operating temperature of the engine is limited by the materials from which they are made. Exceed the limit and the damage is irreparable, so the turbine temperature is always monitored. It is measured with thermocouples placed in the gas flow somewhere in the turbine assembly, typically after the high or low-pressure turbine, and called the exhaust gas temperature. Older engines may name it after the probe position: turbine inlet temperature, turbine gas temperature, or jet pipe temperature. In modern engines the probes sit inside selected nozzle guide vanes, sheltered from the battering of the fast gas. As you open the throttle, fuel flow increases and the exhaust gas temperature rises with it.
Summary
What to take into the exam Stage Stator (NGVs) then rotor. NGVs: convergent, velocity up, pressure down. Across the turbine p and T fall.
Gas changes Pressure: down, down. Temperature: down, down. Velocity: up in NGVs, down in rotor.
Creep Permanent elongation from high temperature + tensile (centrifugal) load. Finite blade life.
Materials Steel → nickel → superalloys (≈1 100 °C, 1 425 °C cooled) → single crystal. Ceramic coatings.
Blades Impulse: expands in stator. Reaction: in rotor. Normal blade: impulse root, reaction tip, twisted.
Fixing Fir-tree root: loose when stopped (ticking normal), held by centrifugal force when running.
Spools HP fastest, LP slowest. Free turbine: last, no mechanical link to any compressor.
Limits Losses ≈ 8 %. Shrouds cut tip leakage and vibration. NGV/blade materials limit temperature; watch EGT.
Chapter 18 · The Turbine Assembly
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up the turbine. A stage is a row of nozzle guide vanes followed by a row of blades. The vanes are convergent nozzles: velocity up, pressure and temperature down, and across the whole turbine both pressure and temperature fall. Creep is permanent elongation from high temperature and centrifugal tension, so blades have a finite life; superalloys, cooling and single-crystal casting fight it. In an impulse turbine the gas expands in the stator, in a reaction turbine in the rotor, and the usual blade is impulse at the root and reaction at the tip, twisted so that it does equal work along its length. Fir-tree roots are loose when stopped and pulled tight by centrifugal force. The free turbine is last and drives no compressor. Losses are about eight per cent, and the temperature limit is watched through the exhaust gas temperature.