General Navigation · Chapter 9
Multi-Drift Winds and Wind Components
Find the wind from drift alone, and split any wind into headwind and crosswind for the runway.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter 9 covers two more uses of the wind face: finding the wind from drift alone, with three or two headings; and resolving a wind into headwind and crosswind components, with crosswind, headwind and tailwind limits.
Chapter roadmap
What this chapter covers
01
Multi-drift winds Three headings, three drifts, one wind.
02
Two-drift winds Along the airways.
03
Wind components Headwind and crosswind.
04
Limits Crosswind, headwind, tailwind.
Chapter 9 · Multi-Drift Winds and Wind Components
02
E-books by eatpl.in · © 2026 · Do not copy or distribute
Four parts: multi-drift winds; two-drift winds on the airways; wind components for the runway; and crosswind, headwind and tailwind limits, including the allowable wind angle.
01
Multi-drift winds
Drift only, no groundspeed.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part one: multi-drift winds.
Why drift only?
Drift is easy to see; groundspeed is not
Drift An experienced pilot can judge drift well from how objects on the ground track beneath the aircraft: bush and maritime patrol pilots develop the skill.
Groundspeed Hard to judge quickly: DME timing works only flying directly to or from the beacon; a stopwatch run needs pre-planned distances.
Three headings Fly 2, or better 3 , headings that cut at large angles: the best is 3 headings 60° apart.
Chapter 9 · Multi-Drift Winds and Wind Components
04
E-books by eatpl.in · © 2026 · Do not copy or distribute
Pilots can often estimate drift with considerable accuracy, from the angle between their heading and the way objects on the ground track beneath them; bush pilots and maritime patrol pilots in particular develop this skill. Groundspeed is much harder: DME timing only works when tracking directly towards or away from the beacon, and a stopwatch over a measured distance needs detailed preparation. But a wind can be found from drift alone, by flying two, or better three, headings which cut at a large angle. The best multi-drift winds come from three headings 60 degrees apart.
Multi-drift in 3D
Three headings, three drifts
TAS 120 kt , starting on heading 030° : drift 10° P Turn 60° left to 330° : drift 5° P Turn 120° right to 090° : drift 5° P Then back to the original heading On the wind face the three drift lines cross at 115/21
Chapter 9 · Multi-Drift Winds and Wind Components
05
E-books by eatpl.in · © 2026 · Do not copy or distribute
A pilot heading 030 at 120 knots wants a wind update. He assesses the drift on his present heading, 10 degrees port; turns 60 degrees left onto 330 and assesses again, 5 port; then turns 120 degrees right onto 090 for a third assessment, 5 port. Then he returns to his original heading. Three drifts on three headings 60 degrees apart are enough to find the wind.
On the wind face
Drift lines cross at the wind point
Heading 030 at the index, TAS 120 under the centre Draw the whole 10° P drift line Heading 330, TAS still 120: a short cross-cut on 5° P Heading 090: a cross-cut on 5° P The lines meet at the wind point Rotate it below the centre: 115/21
20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400 00 03 06 09 12 15 18 21 24 27 30 33 TRUE HEADING 40 30 20 10 10 20 30 40 HDG 030, TAS 120: draw the whole 10° P drift line HDG 330: cross-cut the 5° P line HDG 090: cross-cut the 5° P line the lines cross at the wind point rotate it below the centre: W/V 115/21 W/V 115/21
Chapter 9 · Multi-Drift Winds and Wind Components
06
E-books by eatpl.in · © 2026 · Do not copy or distribute
On the wind face, put heading 030 at the index and 120 knots under the centre dot, and with a straight edge draw a line along the whole length of the 10 degree port drift line. Rotate to the second heading, 330, check the TAS is still under the centre, and draw a short cross-cut along the 5 degree port line. Rotate to 090 and cross-cut the 5 degree port line again. If the drifts were assessed correctly the three lines meet at a point, the wind point. Rotate it to the six o’clock position and read the wind: 115 at 21 knots. If the lines form a triangle, the cocked hat, its size shows the accuracy: a small one means a small probable error, and you take its centre; a large one means one or more drifts were wrong.
If the three lines meet at a point, the drifts were probably all correct A small triangle, the cocked hat : small probable error, take its centre A large one: one or more drifts are wrong Two drifts give no check, so three are better
The cocked hat Lines coincide drifts probably all correct Small cocked hat small error: take the centre Large cocked hat one or more drifts wrong
Chapter 9 · Multi-Drift Winds and Wind Components
07
E-books by eatpl.in · © 2026 · Do not copy or distribute
If the three lines do not coincide they form a triangle, known as the cocked hat. Its size shows the accuracy of the drift assessment: if the lines meet at a point, the drifts were probably all correct; with a small cocked hat the probable error is small, and you take the centre as the wind point; a large one means one or more drifts are in error.
Two-drift winds
Drifts from holding VOR radials
Two headings nearly at right angles, certainly more than 70° apart Brecon → Wallasey on A25 (008°M), then Wallasey → Ottringham on B1 (085°M) Trial and error finds the drift that holds each VOR radial Two drifts cross-cut on the wind face; no third line to check them
Two-drift wind on the airways (schematic) Brecon Wallasey Ottringham A25 · 008°M B1 · 085°M drift 1 found holding the radial drift 2 on the outbound radial Two headings ≈ 77° apart cross-cut the two drift lines on the wind face: the wind point
Chapter 9 · Multi-Drift Winds and Wind Components
08
E-books by eatpl.in · © 2026 · Do not copy or distribute
A three-drift wind is for special cases such as bush or maritime flying. On UK airways, in an aircraft with no RNAV, GPS, INS or FMS, a two-drift wind can be used, with the two headings nearly at right angles and certainly more than 70 degrees apart. From Brecon to Wallasey along A25 the track is 008 magnetic; the pilot applies his planned drift, and if the radial changes he regains the centreline and adjusts the drift, until he holds it. After Wallasey, outbound on B1 at 085 magnetic, he does the same. He then has drifts on two headings, and cross-cuts them on the wind face. The only weakness is that there is no third line to confirm the other two.
Questions
Multi-drift winds
Question 1 TAS 180 kt
Heading Drift 130 6°P 070 4°P 190 2°P
W/V: ?
Question 2 TAS 150 kt
Heading Drift 045 3°S 345 6°P 105 8°S
W/V: ?
Question 3 TAS 120 kt
Heading Drift 270 2°S 210 12°S 330 9½°P
W/V: ?
Question 4 TAS 165 kt
Heading Drift 100 2°P 040 14°P 160 12°S
W/V: ?
Chapter 9 · Multi-Drift Winds and Wind Components
09
E-books by eatpl.in · © 2026 · Do not copy or distribute
The four multi-drift problems: draw the three drift lines at the given TAS and find the wind.
Answers
Multi-drift winds: answers
Question 1 TAS 180 kt
Heading Drift 130 6°P 070 4°P 190 2°P
W/V: 205/18
Question 2 TAS 150 kt
Heading Drift 045 3°S 345 6°P 105 8°S
W/V: 026/22
Question 3 TAS 120 kt
Heading Drift 270 2°S 210 12°S 330 9½°P
W/V: 098/30
Question 4 TAS 165 kt
Heading Drift 100 2°P 040 14°P 160 12°S
W/V: 107/40
Chapter 9 · Multi-Drift Winds and Wind Components
10
E-books by eatpl.in · © 2026 · Do not copy or distribute
The answers: 205/18, 026/22, 098/30 and 107/40.
02
Wind components
Along the runway and across it.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: wind components.
Wind components in 3D
Headwind, crosswind, and the limit
R/W 27, W/V 310/30: 40° off from the right Headwind 30 × cos 40° = 23 kt ; crosswind 30 × sin 40° = 19 kt Then R/W 23 with the wind from 195°M growing Crosswind limit 25 kt reached at about 44 kt
Chapter 9 · Multi-Drift Winds and Wind Components
12
E-books by eatpl.in · © 2026 · Do not copy or distribute
The wind rarely blows straight down the runway. With runway 27 and a wind of 310 at 30, the wind is 40 degrees off the runway from the right. Part of it acts along the runway, the headwind component, 30 times cos 40, 23 knots; part acts across it, the crosswind component, 30 times sin 40, 19 knots, from right to left. In the second half, on runway 23, a wind from 195 magnetic grows: its crosswind component reaches the 25 knot limit at about 44 knots.
On the computer
R/W 27, ATIS 310/30
Use the square graph at the bottom of the slide Wind direction 310 at the index; plot 30 kt below the centre Rotate the runway QDM 270 to the index Read down the vertical axis: headwind 23 kt Read across : crosswind 19 kt , right to left Check: 30 cos 40° = 23, 30 sin 40° = 19. In the exam, use the computer.
10 10 10 20 20 20 30 30 30 40 40 40 50 50 50 60 60 60 00 03 06 09 12 15 18 21 24 27 30 33 INDEX 1 · W/V 310 at the index: plot 30 kt below the centre 2 · rotate the runway QDM 270 to the index 3 · read down: headwind 23 · across: crosswind 19 HEAD / CROSS 23 kt 19 kt cross
Chapter 9 · Multi-Drift Winds and Wind Components
13
E-books by eatpl.in · © 2026 · Do not copy or distribute
On the computer, use the square graph part of the slide. Plot the wind in the normal way: 310 at the index, a mark 30 knots below the centre. Rotate the disc to put the runway QDM, 270, at the index. Read vertically down the axis for the headwind component, 23 knots, and across from the centreline for the crosswind component, 19 knots, from right to left. You could do it with cosines and sines, but the computer is quicker and is what the exam expects.
Why it matters
Headwind helps; crosswind is limited
Headwind Stopping energy is ½mv², with v the groundspeed . A headwind lowers it; a heavy aircraft on a short runway may need a minimum headwind .
Crosswind Crab on finals, then rudder to align at touchdown: “kicking off the drift”. Tyres take sideways loads badly; a high fin can weathercock the aircraft off the runway.
Limits A maximum crosswind for the type, and company rules too: for example the first officer may land only up to 15 kt , the captain up to 25.
Chapter 9 · Multi-Drift Winds and Wind Components
14
E-books by eatpl.in · © 2026 · Do not copy or distribute
Pilots need both components. Threshold speed is a CAS, which corresponds to a TAS, but stopping depends on half m v squared, with v the groundspeed: a headwind reduces it, and a heavy aircraft on a short runway may have a minimum headwind requirement. Crosswind can be more critical: the pilot crabs on finals and must apply rudder to align with the runway at touchdown, known as kicking off the drift; even if perfectly judged there is still a sideways velocity on tyres built mainly for fore-and-aft loads; and once down, a high fin can weathercock the aircraft as the rudder loses authority. So each type has a maximum crosswind, and companies may set their own, lower limits.
True or magnetic?
Know where the wind came from
Source Wind direction Why ATC and ATIS Magnetic used to line up on runways, which are magnetic TAF, METAR, VOLMET True written forecasts and reports; planning tracks are in true
Chapter 9 · Multi-Drift Winds and Wind Components
15
E-books by eatpl.in · © 2026 · Do not copy or distribute
Any forecast wind, and any written meteorological information such as a TAF or METAR, gives the direction in true; VOLMET too. Information to help line the aircraft up on the runway is magnetic, because runway directions are magnetic: a wind from ATC, and the ATIS, are always magnetic. So before resolving a TAF wind on a runway, apply the variation; with an ATIS wind, don’t: a question may give you variation as a trap.
03
Limits
Work it out before the approach.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: crosswind, headwind and tailwind limits.
Crosswind limit
Maximum wind from a given direction
TAF W/V 180/10G50 Variation 15°W R/W 23 Crosswind limit 25 kt
QDM 230 at the index; draw lines 25 kt either side of the centreline Rotate to the wind direction in magnetic : 195°M Read where the limit line crosses the centreline below the centre 25 ÷ sin 35° = 44 kt . Below that from 195°M, you may land.
10 10 10 20 20 20 30 30 30 40 40 40 50 50 50 60 60 60 00 03 06 09 12 15 18 21 24 27 30 33 INDEX R/W QDM 230 at the index draw the 25 kt crosswind limit lines rotate to the wind direction: 180°T + 15°W = 195°M limit line meets the centreline at 44 kt MAX WIND 44 kt from 195°M
Chapter 9 · Multi-Drift Winds and Wind Components
17
E-books by eatpl.in · © 2026 · Do not copy or distribute
With a gusting wind you may try to land between gusts, asking for a spot wind at the committal point; that is no time to calculate, so work out the limiting wind at top of descent. TAF 180 at 10 gusting 50, variation 15 west, runway 23, crosswind limit 25 knots. You can’t plot a single wind, so put the runway and the limit on the computer instead: 230 at the index, and lines 25 knots either side of the centreline. Rotate to the wind direction in magnetic: 180 true plus 15 west is 195 magnetic. Where the limit line crosses the centreline is the maximum wind from that direction: 25 divided by sin 35 is 44 knots. Below that, you may land.
Headwind and crosswind
A minimum and a maximum
ATC W/V 030/10G40 R/W 35 Minimum headwind 10 kt Crosswind limit 20 kt
Draw the 20 kt crosswind lines and a 10 kt headwind line across Rotate to 030°M Headwind line meets the centreline at 13 kt ; crosswind line at 31 kt 10 ÷ cos 40° = 13, 20 ÷ sin 40° = 31. Between 13 and 31 kt you may land.
10 10 10 20 20 20 30 30 30 40 40 40 50 50 50 60 60 60 00 03 06 09 12 15 18 21 24 27 30 33 INDEX R/W 35: QDM 350 at the index 20 kt crosswind lines; 10 kt headwind line rotate to the wind direction 030°M land with 13 to 31 kt from 030°M MIN / MAX 13 / 31 kt from 030°M
Chapter 9 · Multi-Drift Winds and Wind Components
18
E-books by eatpl.in · © 2026 · Do not copy or distribute
Sometimes you are limited by both. A heavy aircraft on a short runway may need at least 10 knots of headwind, while there is also a 20 knot crosswind limit. Runway 35, ATC wind 030 at 10 gusting 40. Draw the 20 knot crosswind lines, and a line across 10 knots below the centre for the minimum headwind. Rotate to 030. The headwind line crosses the centreline at 13 knots and the crosswind line at 31 knots. Below 13 knots from 030 you have less than 10 knots of headwind; above 31, more than 20 knots of crosswind. Between them you may land. 10 divided by cos 40 is 13.
Tailwind limit
Or treat it as the other runway
ATIS W/V 320/10G30 R/W 09 Variation 10°E (a trap: ATIS is magnetic) Max tailwind 10 kt
Runway 09 at the index; draw the tailwind line 10 kt above the centre Rotate to 320°M; read where the line meets the centreline Answer 16 kt : the same as a 10 kt headwind on R/W 27
10 10 10 20 20 20 30 30 30 40 40 40 50 50 50 60 60 60 00 03 06 09 12 15 18 21 24 27 30 33 INDEX R/W 09: QDM 090 at the index draw the 10 kt tailwind line above the centre rotate to 320°M (ATIS is magnetic: ignore variation) it crosses the centreline at 16 kt MAX WIND 16 kt from 320°M
Chapter 9 · Multi-Drift Winds and Wind Components
19
E-books by eatpl.in · © 2026 · Do not copy or distribute
In general, avoid landing with a tailwind: ask for the other end. But you may meet questions on it. Runway 09, variation 10 east, ATIS 320 at 10 gusting 30, maximum tailwind 10 knots. ATIS is magnetic, so the variation is a trap: ignore it. On a real computer the tailwind line lies in the curved part of the slide, so move the slide to put 10 under the centre, draw the line, and move it back to zero. Then rotate to 320 and read where the line crosses the centreline: 16 knots. Or treat it as a 10 knot headwind problem on the reciprocal runway, 27: the same answer.
Allowable wind angle
Which directions can a 50 kt wind blow from?
Runway 250°M at the index; mark 50 kt on the centreline below the centre Turn the disc until the mark shows 30 kt crosswind: 214°M at the index Turn the other way: 286°M From 214° to 286°M the crosswind is 30 kt or less Also from 034° to 106°M, the reciprocals, but with a tailwind Check: sin⁻¹(30/50) = 37°, and 250 ± 37 = 213, 287.
10 10 10 20 20 20 30 30 30 40 40 40 50 50 50 60 60 60 00 03 06 09 12 15 18 21 24 27 30 33 INDEX R/W 250 at the index; mark 50 kt on the centreline turn clockwise until 30 kt crosswind: 214°M turn anticlockwise: 286°M winds of 50 kt from 214° to 286°M are within 30 kt ALLOWED 214–286 + 034–106 tail
Chapter 9 · Multi-Drift Winds and Wind Components
20
E-books by eatpl.in · © 2026 · Do not copy or distribute
Between which directions may a wind of 50 knots blow without exceeding a 30 knot crosswind on runway 250 magnetic? Set the runway at the index and mark 50 knots on the centreline. Turn the disc clockwise until the mark shows a crosswind of 30 knots and read the direction at the index, 214. Turn anticlockwise and repeat: 286. So a 50 knot wind from between 214 and 286 magnetic is within the limit. The same crosswind applies from 034 to 106, the reciprocals, but with a tailwind.
Questions
Wind components
Question 1 An airfield has runways 18/36 and 07/25, all of equal length. The TAF W/V is 310/25 and variation 20°E. Which is the best runway?
a. 18
b. 36
c. 07
d. 25
Question 2 In Question 1, what are the head and cross wind components on that runway?
a. 24 / 17
b. 13 / 19
c. 19 / 16
d. 17 / 12
Question 3 Take-off needs 10 kt headwind; crosswind limit 20 kt; only R/W 25; ATIS 290/10G40. Minimum and maximum windspeeds?
a. 17 / 31
b. 13 / 17
c. 13 / 31
d. 17 / 26
Question 4 You can accept 10 kt tailwind. QDM 047, variation 17°E, ATIS wind direction 210. Maximum wind strength?
a. 18 kt
b. 11 kt
c. 8 kt
d. 4 kt
Chapter 9 · Multi-Drift Winds and Wind Components
21
E-books by eatpl.in · © 2026 · Do not copy or distribute
The four wind component questions.
Answers
Wind components: answers
Question 1 An airfield has runways 18/36 and 07/25, all of equal length. The TAF W/V is 310/25 and variation 20°E. Which is the best runway?
a. 18
b. 36
c. 07
d. 25
310°T + 20°E = 290°M: 40° off R/W 25, 70° off R/W 36.
Question 2 In Question 1, what are the head and cross wind components on that runway?
a. 24 / 17
b. 13 / 19
c. 19 / 16
d. 17 / 12
25 cos 40° = 19 head, 25 sin 40° = 16 cross.
Question 3 Take-off needs 10 kt headwind; crosswind limit 20 kt; only R/W 25; ATIS 290/10G40. Minimum and maximum windspeeds?
a. 17 / 31
b. 13 / 17
c. 13 / 31
d. 17 / 26
40° off: 10 ÷ cos 40° = 13, 20 ÷ sin 40° = 31.
Question 4 You can accept 10 kt tailwind. QDM 047, variation 17°E, ATIS wind direction 210. Maximum wind strength?
a. 18 kt
b. 11 kt
c. 8 kt
d. 4 kt
ATIS is magnetic: 210 is 17° off the reciprocal 227; 10 ÷ cos 17° = 10.5 ≈ 11 kt.
Chapter 9 · Multi-Drift Winds and Wind Components
22
E-books by eatpl.in · © 2026 · Do not copy or distribute
Answers: 1 d, 2 c, 3 c, 4 b, with the working.
Summary
Multi-drift winds and wind components
Item Remember Multi-drift 3 headings 60° apart (or 2, more than 70°); draw drift lines at the TAS; they cross at the wind point Cocked hat small: take the centre; large: a drift is wrong Components W/V plotted, runway at the index: read down for headwind, across for crosswind True or magnetic ATC and ATIS magnetic; TAF, METAR, VOLMET true Limits draw the limit lines with the runway at the index, rotate to the wind direction, read the centreline
Chapter 9 · Multi-Drift Winds and Wind Components
23
E-books by eatpl.in · © 2026 · Do not copy or distribute
In summary: drift lines on two or three headings cross at the wind point; for components, plot the wind, put the runway at the index and read down and across; ATC and ATIS winds are magnetic, forecasts true; and for limits, draw the lines with the runway at the index and rotate to the wind direction.
Try it yourself
Wind Components Lab
Headwind and crosswind for any runway and wind Crosswind, headwind and tailwind limits Allowable wind directions for a given speed Multi-drift winds: draw the lines, find the wind Open the Wind Components Lab →
10 10 10 20 20 20 30 30 30 40 40 40 50 50 50 60 60 60 00 03 06 09 12 15 18 21 24 27 30 33 INDEX
Chapter 9 · Multi-Drift Winds and Wind Components
24
E-books by eatpl.in · © 2026 · Do not copy or distribute
The Wind Components Lab resolves any wind on any runway, finds limiting wind speeds and allowable directions, and finds multi-drift winds by drawing the drift lines on a wind face.
eatpl.in · General Navigation · Chapter 9
Wind Components Lab
Resolve any wind on any runway, find the limiting wind speed or the allowable wind directions, and find a wind from drifts alone.
Components
Limits
Wind angle
Multi-drift
Practice
Multi-drift winds
Wind components
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.