1000 1020 1040
General Navigation · Chapter 11
Navigation Using the 1 in 60 Rule
Off track? How to get back: double track error, closing angle, and new track reference.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter 11 uses the 1 in 60 rule to get back on track. It separates track error from drift, then covers the three techniques: double track error, track error plus closing angle, and the single calculation, which leads to the preferred method, new track reference.
Chapter roadmap
What this chapter covers
01
Track error Planned track, track made good, and why track error is not drift.
02
Double track error Turn twice the error and be back on track in the same time.
03
Closing angle Head straight for the destination: track error plus closing angle.
04
New track reference The preferred method: proportion of the leg × closing angle.
Chapter 11 · Navigation Using the 1 in 60 Rule
02
E-books by eatpl.in · © 2026 · Do not copy or distribute
Four parts: track error versus drift, the double track error method, the closing angle methods, and new track reference. Then practice questions and the Track Correction Lab.
01
Track error
The difference between where you meant to go and where you went.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Track error is not drift
Track error, expected drift, actual drift
Planned track : where you meant to go. Track made good (TMG): where you wentTrack error angle = planned track to TMGDrift = heading to track: expected drift to the planned track, actual drift to the TMGTrack error = the difference between expected and actual drift, but it is not drift Assume a heading change of 10° gives a track change of 10°.
090° planned track 100° heading expected drift 10° track made good 080° track error 10° L actual drift 20°
Chapter 11 · Navigation Using the 1 in 60 Rule
04
E-books by eatpl.in · © 2026 · Do not copy or distribute
The track you intended is the planned track. The track you actually made over the ground, usually because the wind is not what was forecast, is the track made good. The angle between them is the track error angle. That is not drift: drift is the angle between heading and track. In the example the heading is 100 for a planned track of 090, an expected drift of 10 degrees. The aircraft actually made good 080: actual drift 20 degrees, track error 10 degrees left. Track error is the difference between expected and actual drift, but it is not drift itself. These quick techniques assume that changing heading by some angle changes track by the same angle.
Getting back to track
Three techniques, one preferred method
Double track error Turn twice the track error. Back on track after the same time; then take off half the turn.
Track error + closing angle Turn the track error to parallel, plus the closing angle to head for the destination.
Single calculation Closing angle × (total leg ÷ distance gone). Same answer, one sum.
New track reference The preferred method: estimate the fraction of the leg flown, invert it, multiply by the closing angle.
Chapter 11 · Navigation Using the 1 in 60 Rule
05
E-books by eatpl.in · © 2026 · Do not copy or distribute
There are three basic techniques: double track error, track error plus closing angle, and a single calculation that gives the same answer as the second. From these comes the preferred technique, new track reference.
02
Double track error
Turn twice the error, and be back on track in the same time.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: the double track error method.
Double track error
Turn twice the error, regain in the same time
On track at 1000 . At 1020 , a pinpoint: 4 nm left after 30 nm = 8° left Turning 8° right only parallels track Turn 16° right , double the error: an isosceles triangle closing at 8° Back on track at 1040 : no map-reading needed, just the clock Then turn 8° left : you are now on the heading that would have held track
planned track keep going: further off turn 8° R: parallel 4 nm 1020 · 4 nm left after 30 nm = 8° L turn 16° R (double) 1040 on track · turn 8° L 1000 Same distance off as back: same time, 20 min each way
Chapter 11 · Navigation Using the 1 in 60 Rule
07
E-books by eatpl.in · © 2026 · Do not copy or distribute
You are on track at 1000 and at 1020 a pinpoint shows you 4 miles left after 30 miles: 8 degrees left. Doing nothing, you keep diverging. Turning 8 degrees right merely parallels track. So turn another 8, a total of 16 degrees right. That makes an isosceles triangle, closing on track at 8 degrees, so it takes the same distance, and the same time, to get back as it took to get off: you regain track at 1040. Then turn back 8 degrees left, or you will drift off to the right. You end up 8 degrees right of the original heading, which is the heading that would have kept you on track all along. Use this method only if you are less than half way along the leg.
03
Closing angle
Head straight for the destination.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: track error and closing angle.
Track error and closing angle
Turn the track error plus the closing angle
Leg 78 nm . After 30 nm, 4 nm left: track error 8° Turning 8° only parallels track 48 nm to go, 4 nm off: 1 in 12 = 5 in 60, closing angle 5° Turn 8 + 5 = 13° right for B Use this when you want the destination directly, or when you are more than half way: double track error would not regain track in time.
A B TE 8° CA 5° 30 nm gone 48 nm to go 4 nm Turn 8° + 5° = 13° right, direct to B
Chapter 11 · Navigation Using the 1 in 60 Rule
09
E-books by eatpl.in · © 2026 · Do not copy or distribute
Sometimes you want to head straight for the destination, or you are more than half way along the leg so double track error would not regain track before the turning point. Then use track error plus closing angle. The leg is 78 miles. After 30 miles you are 4 miles left: track error 8 degrees. Turning 8 right parallels track. With 48 miles to go, 4 miles off is 1 in 12, 5 in 60: a closing angle of 5 degrees. So turn 8 plus 5, 13 degrees right, for B.
The single calculation
Closing angle × leg ÷ gone
Same problem : 78 nm leg, 30 nm gone, 4 nm left
CA = 4 in 48 = 5°
5° × 78 ÷ 30 = 13°
In practice, estimate the fraction
A third of the way: alter by 3 × CA A quarter : 4 × CAHalf way: 2 × CA
Chapter 11 · Navigation Using the 1 in 60 Rule
10
E-books by eatpl.in · © 2026 · Do not copy or distribute
There is a single calculation that gives exactly the same answer, without working out the track error. Find only the closing angle, 5 degrees, and multiply it by the leg length over the distance gone, 78 over 30: 13 degrees. It is not an approximation; it can be proved geometrically. In practice you estimate: a third of the way along means alter by three times the closing angle, a quarter four times, half way twice.
Using these methods in practice
Mark up the map before you fly
40 30 20 10 10° track error lines from the start 10° closing angle lines to the end Distance-to-go markers every 10 nm (a 44 nm leg) 10° lines at each end let you read track error and closing angle at a glance, with no protractor.
Distance-to-go markers, not distance gone, show how far is left and give a 10 nm scale for distance off.
Chapter 11 · Navigation Using the 1 in 60 Rule
11
E-books by eatpl.in · © 2026 · Do not copy or distribute
In practice you do not calculate in the air. Before flight, mark the track with guide lines: one 10 degree line at each end is enough, because more clutters the chart. Then any fix shows its track error and closing angle at a glance. Also mark distance to go every 10 miles, not distance gone. You can then see how far is left without subtraction, and you have a 10 mile scale for judging distance off. Then if a fix is a quarter of the way along, alter by four times the closing angle; a third, three times; half way, twice.
04
New track reference
The preferred method.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part four: new track reference.
New track reference
Fraction flown, inverted, × closing angle
Hold a steady heading until your position is definitely pinpointed Estimate the fraction of the leg flown: ¼ Invert it: 4 . Multiply by the closing angle 5°: alter 20° Later fix D, half way along the new track C–B, CA 2°: alter 4° Judge the second closing angle and fraction against the new track C–B, which is not drawn on your chart.
¼ ½ ¾ A B C: ¼ of the way, CA 5° alter 4 × 5° = 20° R: new track C–B D: ½ of C–B, new CA 2° alter 2 × 2° = 4° R, judged against the new track C–B
Chapter 11 · Navigation Using the 1 in 60 Rule
13
E-books by eatpl.in · © 2026 · Do not copy or distribute
New track reference is the preferred method. First, hold a steady heading until the position is definitely pinpointed, rather than making panicky alterations. Then estimate the fraction of the leg covered, invert it, and multiply by the closing angle. At C you are about a quarter of the way along with a closing angle of 5 degrees: 4 times 5 is a 20 degree alteration, onto a new track from C to B. If the wind changes again and a later fix D is about half way along C to B with a closing angle of 2 degrees, the alteration is 2 times 2, 4 degrees. The catch: the second closing angle and fraction must be judged against the new track C to B, which is not drawn on your chart.
Summary
What to take into the exam
Track error ≠ drift Drift is heading to track. Track error is planned track to TMG.
Double track error Turn 2 × TE; back on track in the same time; then take off 1 × TE. Before half way only.
Direct to destination Alter by TE + CA, or CA × leg ÷ gone.
New track reference Fraction flown, inverted, × CA. Re-judge from the new track.
Chapter 11 · Navigation Using the 1 in 60 Rule
14
E-books by eatpl.in · © 2026 · Do not copy or distribute
Four things: track error is not drift; double track error gets you back on track in the same time; to go direct, alter by track error plus closing angle, or the single calculation; and new track reference, the preferred method.
Practice · Questions 1–4
Track error, closing angle and drift
1. 3° off required track at a range of 120 nm. How far off track?
2. 2 nm off required track at 40 nm. Track error?
3. A to B, 95 nm. After 35 nm, a pinpoint 7 nm right of track. (a) Track error? (b) Alteration direct to B? (c) Drift?
4. Oxford to Cambridge, track 074°M, 70 nm, heading 065°M. After 30 nm, overhead Cranfield, 4 nm left. (a) Track error? (b) TMG? (c) Expected drift? (d) Actual drift? (e) Alteration direct to Cambridge? (f) New heading?
Chapter 11 · Navigation Using the 1 in 60 Rule
15
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 1 to 4 from the end of Chapter 11. 3(c) is a trap. The Track Correction Lab sets up each one.
Practice · Question 5
Norwich to Oxford
5. Norwich to Oxford, track 250°M, 96 nm, heading 260°M, groundspeed 180 kt. Depart 1000. At 1012, overhead Ely, 3 nm right of track.
(a) planned drift (b) track error at 1012 (c) TMG 1000–1012 (d) actual drift (e) alteration direct to Oxford
(f) heading direct to Oxford (g) alteration to regain track at 1024 (h) heading 1012–1024 (i) change and heading from 1024 (j) ETA Oxford
Chapter 11 · Navigation Using the 1 in 60 Rule
16
E-books by eatpl.in · © 2026 · Do not copy or distribute
Question 5 strings the methods together. Work out the distance flown by 1012 first: 12 minutes at 180 knots.
Practice · Answers
Questions 1–4
Q Answer Working 1 6 nm 3 × 120 ÷ 60 2 3° 2 ÷ 40 × 60 3a 12° R 7 in 35 3b 19° L TE 12 + CA 7 (7 in 60) 3c Cannot tell Drift needs the heading
Q Answer Working 4a 8° L 4 in 30 4b 066°M 074 − 8 4c 9° S Heading 065, track 074 4d 1° S Heading 065, TMG 066 4e 14° R TE 8 + CA 6 (4 in 40) 4f 079°M 065 + 14
Chapter 11 · Navigation Using the 1 in 60 Rule
17
E-books by eatpl.in · © 2026 · Do not copy or distribute
Answers. 3(c) cannot be answered: drift is the angle between heading and track, and no heading is given.
Practice · Answers
Question 5
Part Answer Working a 10° P Heading 260, planned track 250 b 5° R 12 min at 180 kt = 36 nm; 3 in 36 c 255°M 250 + 5 d 5° P Heading 260, TMG 255 e 8° L TE 5 + CA 3 (3 in 60 to go) f 252°M 260 − 8 g 10° L 2 × TE h 250°M 260 − 10 i 5° R → 255°M Original heading corrected for TE j 1032 36 nm by 1024; 24 nm left at 3 nm/min = 8 min
Chapter 11 · Navigation Using the 1 in 60 Rule
18
E-books by eatpl.in · © 2026 · Do not copy or distribute
Answers. At 180 knots the aircraft covers 3 miles a minute, so 36 miles by 1012 and another 36 by 1024, leaving 24 miles: 8 minutes, so 1032.
Try it yourself
Track Correction Lab
Enter a leg and a pinpoint: track error, TMG, closing angle and drift See the double track error and direct corrections fly out on a map New headings, regain times and ETA Every practice question, one tap each Open the Track Correction Lab →
fix direct double TE
Chapter 11 · Navigation Using the 1 in 60 Rule
19
E-books by eatpl.in · © 2026 · Do not copy or distribute
The Track Correction Lab takes a leg and a pinpoint and gives the track error, track made good, closing angle and drift, shows the double track error and direct corrections flying out on a map, with new headings, regain times and ETA, and has every practice question.
eatpl.in · General Navigation · Chapter 11
Track Correction Lab
Enter a leg and a pinpoint. Get the track error, closing angle, drift and new headings, and watch both corrections flown on the map.
Leg and fix
Quick 1 in 60
Practice
Fly it
Direct to destination (TE + CA)
Double track error
The questions from the end of Chapter 11. Set up loads the question and works it; Answer shows the answers.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.