1 nm 300 2 nm 600 3 nm 900
General Navigation · Chapter 12
Other Applications of the 1 in 60 Rule
Glide slope heights, rates of descent, and VOR/DME problems, all with the same rule.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter 12 applies the 1 in 60 rule in side view and with radio aids: height on a glide slope, the rate of descent needed to stay on it and how that changes with speed, distance off an airway from a VOR/DME, and range from a change of VOR bearing.
Chapter roadmap
What this chapter covers
01
Glide slopes 100 ft per nautical mile for every degree of slope.
02
Rate of descent 5 × groundspeed on a 3° slope, and changes of speed.
03
VOR/DME Distance off an airway, and range from a change of bearing.
Chapter 12 · Other Applications of the 1 in 60 Rule
02
E-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: height on a glide slope, the rate of descent to hold it, and VOR/DME problems. Then practice and the Approach and VOR Lab.
01
Glide slopes
The 1 in 60 rule in side view.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part one: height on a glide slope.
Height on a glide slope
100 ft per nm for every degree
Take 1 nm as 6000 ft (really 6080: about 1% error). On a 1° slope you climb 1 ft in 60, so 100 ft in 6000.
Height (ft) = glide slope (°) × 100 × range (nm)
3° at 4 nm: 3 × 100 × 4 = 1200 ft 3° at 2 nm: 600 ft 5.5° at 3 nm: 5.5 × 100 × 3 = 1650 ft
Chapter 12 · Other Applications of the 1 in 60 Rule
04
E-books by eatpl.in · © 2026 · Do not copy or distribute
View the track error triangle in side elevation and it gives glide slope heights. Call a nautical mile 6000 feet rather than 6080, about 1 percent error. On a 1 degree slope you rise 1 foot in 60, 10 in 600, 100 in 6000: 100 feet per nautical mile. On 2 degrees, 200 feet per mile. So height in feet is the glide slope times 100 times the range in nautical miles. On a 3 degree slope at 4 miles you should be at 1200 feet; the clip flies the approach and checks it at each mile.
Common glide slopes
From 2.5° jets to 5.5° at London City
Glide slope Height per nm 2.5° 250 ft 3° 300 ft 3.5° 350 ft 5.5° 550 ft
Where you meet them 3° is the most common. 2.5° is often used at military airfields with fast jets. Steeper slopes are used near high terrain or buildings: London City is 5.5°.
In the exam the glide slope is always given.
Chapter 12 · Other Applications of the 1 in 60 Rule
05
E-books by eatpl.in · © 2026 · Do not copy or distribute
The rule gives 100 feet per mile for each degree: 250 feet per mile on 2.5 degrees, 300 on 3, 350 on 3.5, 550 on 5.5. Three degrees is the most common. Two and a half degree slopes are often found at military airfields operating fast jets. Steeper slopes are used where there is high terrain or tall buildings nearby; London City is a very steep 5.5 degrees. In exam questions the glide slope is always given.
02
Rate of descent
Lose one minute's height in one minute.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: rate of descent.
Rate of descent
ROD = 5 × groundspeed on a 3° slope
One minute from touchdown you must lose your height in one minute. The range one minute out is groundspeed ÷ 60 .
60 kt: 1 nm out, 300 ft: 300 ft/min 120 kt: 2 nm out, 600 ft: 600 ft/min 140 kt (Heathrow ILS): 5 × 140 = 700 ft/min
3° glide slope 1 minute at 60 kt = 1 nm 300 ft 60 kt: lose 300 ft in 1 min = 300 ft/min 1 minute at 120 kt = 2 nm 600 ft 120 kt: lose 600 ft in 1 min = 600 ft/min ROD = 5 × groundspeed (3° only)
Chapter 12 · Other Applications of the 1 in 60 Rule
07
E-books by eatpl.in · © 2026 · Do not copy or distribute
The rate of descent needed to stay on the glide slope comes from the height one minute before touchdown, because that height has to be lost in one minute. One minute out, the range is the groundspeed divided by 60. At 60 knots that is 1 mile, and on a 3 degree slope 300 feet, so 300 feet per minute. At 120 knots, 2 miles and 600 feet, so 600 feet per minute. Hence, for a 3 degree slope only, rate of descent in feet per minute is 5 times the groundspeed in knots. On a Heathrow ILS at 140 knots, 700 feet per minute.
Other slopes and changes of speed
Solve for 3°, then scale
Not 3°? Multiply by slope ÷ 3 4° at 100 kt: 5 × 100 = 500 for 3°
500 × 4 ÷ 3 = 667 ft/min
London City, 5.5° at 120 kt:
600 × 5.5 ÷ 3 = 1100 ft/min
Change of speed Slower → less ROD. Faster → more ROD.
Change in ROD = 5 × change in groundspeed (3°)
140 → 120 kt: 5 × 20 = −100
5.5°, 120 → 110: 50 × 5.5 ÷ 3 = −92
Chapter 12 · Other Applications of the 1 in 60 Rule
08
E-books by eatpl.in · © 2026 · Do not copy or distribute
For slopes other than 3 degrees, solve for 3 and scale by the actual slope over 3. Four degrees at 100 knots: 500 for 3 degrees, times 4 over 3, about 667 feet per minute. London City, 5.5 degrees at 120 knots: 600 times 5.5 over 3, 1100. To hold the slope, slowing down needs less rate of descent and speeding up more. The change is 5 times the change in groundspeed for a 3 degree slope: from 140 to 120 knots, 100 feet per minute less. On London City's 5.5 degrees, slowing from 120 to 110 knots: 50 times 5.5 over 3, about 92 feet per minute less.
03
VOR/DME
Distance off an airway, and range from a bearing change.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: VOR/DME problems.
VOR/DME: distance off an airway
5° at 48 nm is 4 nm off
Airway to VOR/DME Q: QDM 271°M . Your RMI shows QDM 266°M , DME 48 nm . How far off, and which side?
Angle off = 271 − 266 = 5° Distance off = angle × DME ÷ 60 = 5 × 48 ÷ 60 = 4 nm The station bears left of the airway QDM, so you are right of the centreline Still inside: most airways are 10 nm wide, 5 nm each side.
airway centreline QDM 271° airway: 5 nm each side VOR/DME Q RMI: QDM 266°, DME 48 nm 4 nm 5° off at 48 nm: 5 × 48 ÷ 60 = 4 nm right Station bears 5° left of the airway QDM: you are right of the centreline cross-track drawn ×2
Chapter 12 · Other Applications of the 1 in 60 Rule
10
E-books by eatpl.in · © 2026 · Do not copy or distribute
A typical exam question. You are flying along an airway to VOR/DME Q; the airway QDM is 271 magnetic. Your RMI shows QDM 266 at a range of 48 miles. The track error formula, with the DME range as distance gone, gives distance off equals angle times range over 60: 5 times 48 over 60, 4 miles. The station bears to the left of the airway QDM, so you are to the right of the centreline. You are off track but still inside the airway, which is normally 5 miles either side.
Range from a change of bearing
15 nm for 5° means 180 nm
Tracking 090°M at 180 kt . At 1100 the QDM to a VOR is 002° ; five minutes later it is 357° .
Bearing change: 002 → 357 = 5° Distance flown: 5 min at 180 kt = 15 nm Range = distance flown × 60 ÷ angle = 15 × 60 ÷ 5 = 180 nm Treat the two small triangles (2° and 3°) as one 5° triangle at the closest point of approach, QDM 000.
track 090°M, 180 kt VOR R 1100 · QDM 002° 1105 · QDM 357° 5 min at 180 kt = 15 nm 5° 15 nm subtends 5° R = 15 × 60 ÷ 5 = 180 nm Not to scale: the bearing lines are steepened to show the angle
Chapter 12 · Other Applications of the 1 in 60 Rule
11
E-books by eatpl.in · © 2026 · Do not copy or distribute
The rule also gives range from a VOR from the change in bearing. An aircraft tracks 090 magnetic at 180 knots. At 1100 the QDM to the VOR is 002, and five minutes later 357. The closest point of approach is when the QDM is 000, at right angles to track. You could treat it as two triangles of 2 and 3 degrees, but it is easier to treat it as one near-right-angled triangle with 5 degrees at the top. Five minutes at 180 knots is 15 miles, so 15 miles subtends 5 degrees: for every 60 miles of range the angle subtends 5 miles, so the range is 3 times 60, 180 miles.
Summary
What to take into the exam
Glide slope height Height (ft) = slope (°) × 100 × range (nm).
Rate of descent 3°: ROD = 5 × GS. Other slopes: × slope ÷ 3. Change = 5 × ΔGS.
Airway distance off Angle off × DME ÷ 60. Station left of airway QDM → you are right.
Range from bearings Range = distance flown × 60 ÷ bearing change.
Chapter 12 · Other Applications of the 1 in 60 Rule
12
E-books by eatpl.in · © 2026 · Do not copy or distribute
Four results: height on a glide slope is the slope times 100 times the range; rate of descent on 3 degrees is 5 times the groundspeed, scaled by slope over 3 for other slopes, and the change for a change of speed is 5 times the change; distance off an airway is angle off times DME range over 60; and range from a change of bearing is distance flown times 60 over the angle.
Practice · Questions 1–5
Bearings, heights and rates of descent
1. Flying due south. At 1000, P bears 267°T; at 1006, 275°T. GS 120 kt. Range of P?
2. Innsbruck, glide slope 3.5°. Height (QFE) at 2 nm?
3. Rota runway 28, glide slope 2.6°. Height at 4 nm?
4. Paris CDG, glide slope 3°. Height (QFE) at 2 nm?
5. Rates of descent for: (a) Q2 at 120 kt GS (b) Q3 at 180 kt (c) Q4 at 150 kt
Chapter 12 · Other Applications of the 1 in 60 Rule
13
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 1 to 5 from the end of Chapter 12. The Approach and VOR Lab sets each up.
Practice · Questions 6–8
Changes of speed and airways
6. Heathrow 27, glide slope 3°: you slow from 150 to 120 kt. Change of ROD?
7. Gioia del Colle, glide slope 2.5°, no flaps: 220 kt TAS, 10 kt headwind. (a) ROD? Mid flap lets you slow to 190 kt TAS: (b) change of ROD? (c) new ROD?
8. Airway centreline QDM 137°M towards VOR/DME A. RMI reads 141°M, DME 90 nm. (a) Left or right? (b) Distance off? (c) In trouble with ATC? (Airways 5 nm each side)
Chapter 12 · Other Applications of the 1 in 60 Rule
14
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 6 to 8. In 7, the rate of descent needs groundspeed, but the change only needs the change of speed.
Practice · Answers
Answers and working
Q Answer Working 1 90 nm 12 nm in 8°: 12 × 60 ÷ 8 2 700 ft 2 × 350 3 1040 ft 4 × 260 4 600 ft 2 × 300 5a 700 ft/min 600 × 3.5 ÷ 3 5b 780 ft/min 900 × 2.6 ÷ 3 5c 750 ft/min 5 × 150
Q Answer Working 6 −150 ft/min 5 × 30 7a 875 ft/min GS 210: 1050 × 2.5 ÷ 3 7b −125 ft/min 5 × 30 × 2.5 ÷ 3 7c 750 ft/min 875 − 125 8a Left Station bears right of 137 8b 6 nm 4 × 90 ÷ 60 8c Usually yes Outside 5 nm
Chapter 12 · Other Applications of the 1 in 60 Rule
15
E-books by eatpl.in · © 2026 · Do not copy or distribute
Answers. In 7 the groundspeed is 220 minus 10, 210 knots, but the change in rate of descent needs only the 30 knot change in speed. In 8 the RMI QDM of 141 is right of the airway QDM of 137, so you are left of the centreline, 6 miles off: outside a 5 mile half-width.
Try it yourself
Approach and VOR Lab
Glide slope height at any range, and the range for any height Rate of descent for any slope and groundspeed, and for a change of speed Distance off an airway from an RMI and DME, and range from a bearing change All 8 practice questions, one tap each Open the Approach and VOR Lab →
3° · 4 nm · 1200 ft ROD 5 × GS
Chapter 12 · Other Applications of the 1 in 60 Rule
16
E-books by eatpl.in · © 2026 · Do not copy or distribute
The Approach and VOR Lab gives glide slope heights and ranges, rates of descent for any slope and speed and for a change of speed, distance off an airway from an RMI and DME, and range from a change of bearing, with all eight practice questions.
eatpl.in · General Navigation · Chapter 12
Approach and VOR Lab
Glide slope heights and rates of descent, distance off an airway, and range from a change of bearing, all by the 1 in 60 rule.
Glide slope
Descent rate
VOR airway
Bearing change
Practice
The questions from the end of Chapter 12. Set up loads and works the question; Answer shows the answer.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.