standard parallels great circle ≈ straight line
General Navigation · Chapter 21
Lambert’s Conformal Chart 1
Why conical charts, the simple conic, and Lambert’s two-standard-parallel projection.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter 21 introduces Lambert’s conformal conic chart. Why navigators wanted a conical chart; the simple conic projection, its convergence and scale; and how Lambert modified it in 1777 to give a conformal, nearly constant-scale chart on which great circles are almost straight.
Chapter roadmap
What this chapter covers
01
Why conical? What Mercator cannot do, and why it started to matter.
02
The simple conic The cone, its constant n, and chart convergence.
03
Lambert’s chart Two standard parallels, scale, graticule and tracks.
Chapter 21 · Lambert’s Conformal Chart 1
02
E-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: why navigators wanted a conical chart; the simple conic projection, with its cone constant and chart convergence; and Lambert’s modification and the properties of his chart. Then check-yourself questions and the Lambert Lab.
01
Why conical charts?
What Mercator cannot do.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part one: why conical charts?
Why conical charts?
Two things Mercator cannot do
Great circles are curves On a Mercator a great circle is curved. Fly one and you seem to drift off track mid-leg, then recover.
Since about 1960 , INS, IRS, FMS and GPS compute and fly great circle tracks automatically.
Scale changes fast Mercator scale grows as sec lat: distances need dividers, opened differently at each latitude.
Aircraft have no big plotting table. A chart you can measure with a ruler is far more useful.
The answer A chart on which great circles are straight and scale is nearly constant .
Lambert’s conformal conic, 1777, built on the simple conic.
Chapter 21 · Lambert’s Conformal Chart 1
04
E-books by eatpl.in · © 2026 · Do not copy or distribute
Mercator’s chart has two limitations: great circles are not straight lines, and scale changes quite rapidly. For about four hundred years navigators steered by compass and wanted rhumb lines, so this did not matter. From about 1960, computers in INS, IRS, FMS and GPS calculate great circle tracks, so a chart on which a great circle is straight became valuable. And a chart of nearly constant scale can be measured with a ruler rather than dividers. Johann Heinrich Lambert’s 1777 modification of the simple conic gives both.
02
The simple conic
A cone touching one parallel.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: the simple conic projection.
The simple conic
A cone touching one parallel
Light at the centre of a reduced earth casts the graticule onto a cone that touches one parallel: the parallel of tangency .
Scale is correct on that parallel: the standard parallel Apex angle = 2 × parallel of tangency Rolled out flat, 360° of longitude fills 360 × sin φ degrees At 45°N the segment is 255°, leaving a 105° gap. At the pole, a flat sheet: no gap.
Rolled out flat apex angle 60° cone touches 30°N 360° × sin 30° = 180° pole apex angle 90° cone touches 45°N 360° × sin 45° = 255° pole apex angle 120° cone touches 60°N 360° × sin 60° = 312° pole
Chapter 21 · Lambert’s Conformal Chart 1
06
E-books by eatpl.in · © 2026 · Do not copy or distribute
A cone is placed over a reduced earth so that it touches along one parallel, the parallel of tangency, with its apex on the extended axis. Light at the centre casts the graticule onto the cone, which is then cut down its slant side and rolled out flat. Scale is correct on the parallel of tangency, called the standard parallel, and expands either side. The cone’s apex angle is always twice the parallel of tangency: 60 degrees for 30 north, 90 for 45, 120 for 60. Rolled flat, the 360 degrees of longitude fill a segment of 360 times the sine of that parallel: 180, 255 and 312 degrees. At the pole the cone becomes a flat sheet with no gap.
The constant of the cone
Chart convergence = ch long × sin parallel of origin
Constant of the cone, n n = sin (parallel of origin)
For the simple conic the parallel of origin is the parallel of tangency.
Chart convergence The angle between two meridians on the chart.
CC = ch long × n
Parallel of origin 45°N 100° × sin 45° = 70.71°
10° × sin 45° = 7.071°
360° × sin 45° = 255°
The meridians are straight, so chart convergence is the same at every latitude
Chapter 21 · Lambert’s Conformal Chart 1
07
E-books by eatpl.in · © 2026 · Do not copy or distribute
The relationship between the rolled-out segment and the original 360 degrees of longitude is the sine of the parallel of origin. The same goes for any two meridians: the angle of inclination between them on the chart, the chart convergence, is the change of longitude times the sine of the parallel of origin. With the parallel of origin at 45, 100 degrees of longitude appear as 70.71 degrees between the meridians, and 10 degrees as 7.071. The sine of the parallel of origin is called the constant of the cone, n.
03
Lambert’s chart
The cone pushed inside the earth.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: Lambert’s chart.
Lambert’s modification
Two standard parallels
On the simple conic, scale expands rapidly away from the one standard parallel.
Lambert (1777) made the cone cut inside the reduced earth:
Scale correct on two standard parallels Contracted between them, least on the parallel of origin Expanded outside them
contracted expanded expanded correct 25° 30° 35° 40° 45° 50° 55° 60° 65° +2.5% +5.0% +7.5% +10.0% latitude simple conic: correct only at 45° Lambert: correct at 37° and 53°, least at 45° Scale error: tangent cone (one standard parallel) Push the cone inside: two standard parallels Error spread out and roughly halved
Chapter 21 · Lambert’s Conformal Chart 1
09
E-books by eatpl.in · © 2026 · Do not copy or distribute
On the simple conic the scale is correct on the parallel of tangency but expands rather rapidly away from it. Lambert made the cone go inside the reduced earth, cutting it along two parallels. Scale is now correct on these two, the standard parallels. Between them it is contracted, least of all on the old parallel of tangency, now called the parallel of origin. Outside them it is expanded. The effect is to even out the scale error, making it much more nearly a constant scale chart.
From globe to chart
The real Earth onto Lambert’s cone
The cone cuts the Earth along 37°N and 53°N : scale correct there Between them the surface is squeezed onto the cone; outside, stretched Cut and opened out: straight meridians, parallels as arcs A chart for the middle latitudes, where the cone fits best
Chapter 21 · Lambert’s Conformal Chart 1
10
E-books by eatpl.in · © 2026 · Do not copy or distribute
The clip puts it together on the real Earth. A cone over the Earth is pushed in until it cuts along 37 and 53 north, the standard parallels. The surface is then moved onto the cone: between the standard parallels it is squeezed in, outside them stretched out. Finally the cone is cut and opened out flat. The result is a Lambert chart: straight meridians converging on the pole, parallels as arcs centred on the pole, and the parallel of origin, 45 north, between the standard parallels.
Parallel of origin
Scale from the standard parallels; convergence from the origin
The one-sixth rule Standard parallels sit one sixth of the way in from the top and bottom of the sheet: minimum scale variation.
43°N – 47°N on a 42–48°N sheet
Parallel of origin halfway: 45°N.
Convergence unchanged Lambert kept the cone angle : a smaller cone, or the same cone pushed down.
So n and chart convergence are still set by the parallel of origin .
CC = ch long × sin origin
Non-perspective With the cone inside the earth, mathematical adjustments were needed to keep the chart orthomorphic.
So Lambert’s chart is non-perspective .
Chapter 21 · Lambert’s Conformal Chart 1
11
E-books by eatpl.in · © 2026 · Do not copy or distribute
In the example the standard parallels are 43 and 47 north and the parallel of origin is 45 north. The upper standard parallel is one sixth of the way down from the top of the chart and the lower one sixth of the way up from the bottom: the one-sixth rule, which minimises scale variation over the sheet. Lambert did not change the cone angle, so the constant of the cone and the chart convergence are still defined by the parallel of origin. Scale is correct at the standard parallels, but convergence comes from the parallel of origin. Bringing the cone inside the earth needed mathematical adjustments to keep the chart orthomorphic, so it is non-perspective.
Chart convergence
Constant across the chart
Unlike the Earth, a Lambert chart’s meridians are straight lines radiating from the pole.
So the angle between two meridians is the same wherever you measure it.
CC = ch long × sin parallel of origin, everywhere
On the Earth, convergency = ch long × sin lat: it grows towards the pole.
35°N 40°N 45°N 50°N 55°N 60°N 20°W 20°E CC CC CC CC = 40° × sin 45° = 28.3°, at every latitude Meridians are straight: the angle between them never changes
Chapter 21 · Lambert’s Conformal Chart 1
12
E-books by eatpl.in · © 2026 · Do not copy or distribute
Unlike on the Earth, the meridians of a Lambert chart are straight lines. So the convergence between two meridians does not change with latitude: chart convergence is constant across the chart. The clip parallels the 20 west meridian through three points on the 20 east meridian, and the angle is the same each time: 40 degrees times sine 45, 28.3 degrees. On the Earth, by contrast, convergency is change of longitude times sine latitude, and grows towards the pole.
Graticule and orthomorphism
Straight meridians, curved parallels, right angles
Meridians Straight lines radiating from the pole of the projection.
Parallels Arcs of circles, all centred on the pole. The pole is normally off the sheet .
Orthomorphic The meridians converge and the parallels curve, so they still cut at right angles . Orthomorphic by mathematical construction.
Chapter 21 · Lambert’s Conformal Chart 1
13
E-books by eatpl.in · © 2026 · Do not copy or distribute
The graticule: meridians are straight lines radiating from the pole, and parallels of latitude are arcs of circles, all centred on the pole, which is usually off the map sheet. The chart is orthomorphic by mathematical construction: the meridians converge, but the parallels curve, so that where they cross they meet at right angles.
Tracks
Great circles nearly straight
Great circles : straight at the parallel of origin; elsewhere curves concave to the parallel of origin The curvature is tiny: for plotting, treat them as straight Rhumb lines (other than meridians): curves concave to the pole , much more curvedWhy? Chart meridians are straight, so great circles at high or low latitude get stretched outward. More in Chapter 22.
30°N 40°N 50°N 60°N origin 45° rhumb line (a parallel): concave to the pole Great circles: straight at the origin, concave to it elsewhere Great circle curvature exaggerated ×7: in practice treat as straight
Chapter 21 · Lambert’s Conformal Chart 1
14
E-books by eatpl.in · © 2026 · Do not copy or distribute
Except for the meridians, great circles on a Lambert chart are straight at the parallel of origin and curves concave to the parallel of origin at any other latitude. The real Earth’s meridians converge; the chart straightens them, so great circles at higher or lower latitudes are stretched outwards. The clip exaggerates the curvature seven times: in fact it is very small, and for all practical purposes, including plotting, great circles on a Lambert chart may be treated as straight lines. Rhumb lines, other than meridians, are curves concave to the pole, like the parallels, and far more curved.
Tracks on the real Earth
St John’s to London
On the globe the great circle bows north of the rhumb line Opened onto a Lambert chart the great circle is almost exactly the straight line The rhumb line stays a curve, concave to the pole Plot great circles with a ruler; fly rhumb lines with care
Chapter 21 · Lambert’s Conformal Chart 1
15
E-books by eatpl.in · © 2026 · Do not copy or distribute
The real thing: St John’s, Newfoundland, to London. On the globe the great circle, in orange, runs north of the rhumb line, in green. As the Earth moves onto the cone and the cone opens out, the great circle straightens until it sits almost exactly on the thin blue straight line between the two places. The rhumb line stays a curve, concave to the pole. That is why great circles are plotted with a ruler on a Lambert chart.
Summary
Properties of a Lambert chart
Property Lambert Scale Correct on the standard parallels; contracted between them (least at the parallel of origin); expanded outside Orthomorphic Yes, by mathematical construction (non-perspective) Graticule Meridians straight, from the pole; parallels arcs centred on the pole (always off the map) Parallel of origin Mathematical basis; halfway between the standard parallels; n = sin parallel of origin Chart convergence Constant across the chart: ch long × sin parallel of origin Rhumb lines Meridians straight; all others concave to the pole Great circles Meridians straight; near-straight at the parallel of origin; elsewhere concave to the parallel of origin
Chapter 21 · Lambert’s Conformal Chart 1
16
E-books by eatpl.in · © 2026 · Do not copy or distribute
The summary table from the chapter, all of it examinable. Scale correct on the standard parallels, contracted between, least at the parallel of origin, expanded outside. Orthomorphic. Straight meridians from the pole, parallels arcs centred on it. The parallel of origin halfway between the standard parallels, and n its sine. Chart convergence constant. Rhumb lines concave to the pole. Great circles near-straight, concave to the parallel of origin.
Check yourself · 1–5
eatpl.in check-yourself questions
1. A simple conic touches the earth at 40°N. What arc does the rolled-out segment make?
2. What is the apex angle of a cone tangent at 60°N?
3. A Lambert chart’s parallel of origin is 52°N. What is the constant of the cone?
4. Parallel of origin 45°N. Chart convergence between 10°W and 20°E? Is it different at 40°N and 50°N?
5. Standard parallels 43°N and 47°N. Where is scale correct, where least, and where expanded?
Chapter 21 · Lambert’s Conformal Chart 1
17
E-books by eatpl.in · © 2026 · Do not copy or distribute
These are eatpl.in’s own check-yourself questions.
Check yourself · 6–10
eatpl.in check-yourself questions
6. A sheet covers 40°N to 58°N. By the one-sixth rule, where are the standard parallels and the parallel of origin?
7. Other than meridians, rhumb lines on a Lambert chart are curves concave to what?
8. Where is a great circle most nearly a straight line on a Lambert chart?
9. Why is the Lambert chart non-perspective?
10. Scale is correct on the standard parallels. What defines the chart convergence?
Chapter 21 · Lambert’s Conformal Chart 1
18
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 6 to 10. The Lambert Lab sets up every one.
Check yourself · Answers
Answers and reasons
Q Answer Why 1 231.4° 360 × sin 40° 2 120° Twice the parallel of tangency 3 0.788 sin 52° 4 21.2°; no 30 × sin 45°; meridians are straight, so CC is constant 5 Correct 43° and 47°; least 45°; expanded outside Contracted between the standard parallels 6 SPs 43°N and 55°N; origin 49°N One sixth of 18° = 3° in from each edge 7 The pole Like the parallels of latitude 8 Along the parallel of origin Chart convergence equals earth convergency there 9 Mathematical adjustment Needed to stay orthomorphic once the cone is inside the earth 10 The parallel of origin n = sin parallel of origin; the cone angle was not changed
Chapter 21 · Lambert’s Conformal Chart 1
19
E-books by eatpl.in · © 2026 · Do not copy or distribute
Answers to the check-yourself questions.
Try it yourself
Lambert Lab
A 3D cone on the real Earth: unroll it from globe to chart A real-Earth Lambert chart: pick the standard parallels Scale along the sheet: contracted, correct, expanded Chart convergence versus earth convergency Great circle and rhumb line between any two places All 10 check-yourself questions, one tap each Open the Lambert Lab →
standard parallels great circle ≈ straight line
Chapter 21 · Lambert’s Conformal Chart 1
20
E-books by eatpl.in · © 2026 · Do not copy or distribute
The Lambert Lab draws a real-Earth Lambert chart for any standard parallels, shows the scale across the sheet, compares chart convergence with earth convergency, draws great circles and rhumb lines between any two places, and sets up all ten check-yourself questions.
Standard parallels / great circle
Straight line
Rhumb line
Loading Earth…
2D chart 3D cone
eatpl.in · General Navigation · Chapter 21
Lambert Lab
A real-Earth Lambert conformal chart. Scale correct on the standard parallels; chart convergence = ch long × sin parallel of origin.
Chart & scale
Convergence
Tracks
Practice
eatpl.in check-yourself questions for Chapter 21. Set up draws it; Answer shows the answer.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.