mid-meridian straight line, rhumb line: parallel at the mid-meridian
General Navigation · Chapter 22
Lambert’s Conformal Chart 2
Constant scale, chart versus earth convergence, great circle curvature, and plotting radio bearings.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter 22 continues the Lambert chart: how nearly constant its scale is, the difference between chart and earth convergence, why great circles curve slightly, the mid-meridian rule, the chart’s advantages and disadvantages, and plotting radio bearings on it.
Chapter roadmap
What this chapter covers
01
Scale and convergence How constant the scale is; chart versus earth convergence.
02
Lines on the chart Great circle curvature, the mid-meridian, pros and cons.
03
Plotting VOR and NDB bearings, and straight-line track problems.
Chapter 22 · Lambert’s Conformal Chart 2
02
E-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: how constant the scale is and how chart convergence compares with earth convergence; how straight lines, rhumb lines and great circles relate, with the mid-meridian rule and the chart’s advantages and disadvantages; and plotting radio bearings and straight-line tracks. Then practice and the Lambert Plotting Lab.
01
Scale and convergence
Nearly constant scale; two kinds of convergence.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part one: scale and convergence.
Constant scale
Scale error grows with the gap between the standard parallels
Standard parallels apart Scale error 5⅓° 0.1% 16° 1% 23° 2% 28° 3% 32° 4%
Up to 1% error a chart counts as constant scale: measure with a ruler.
UK CAA 1:500,000 Standard parallels 49°40′N and 52°40′N: about 5° apart.
≈ 0.1% error
Jeppesen ED-6 Standard parallels 37°N and 65°N: 28° apart.
≈ 3% error
Chapter 22 · Lambert’s Conformal Chart 2
04
E-books by eatpl.in · © 2026 · Do not copy or distribute
The Lambert chart is not completely constant scale: it expands outside the standard parallels and contracts between them. But for practical purposes a chart is constant scale if the error does not exceed 1 percent. How much error depends on the separation of the standard parallels: about 0.1 percent for 5 and a third degrees, 1 percent for 16, 2 for 23, 3 for 28 and 4 for 32. You do not need the formula. The UK CAA half-million topographical maps have standard parallels about 5 degrees apart, so a ruler is accurate to about 0.1 percent. The Jeppesen ED-6 series uses 37 and 65 north, 28 degrees apart: about 3 percent.
Why the gap matters
Close standard parallels, small error
CAA 1:500,000: the cone cuts 3° apart and hugs the Earth: ≈ 0.1% Jeppesen ED-6: the cone cuts 28° apart and sits well inside the Earth between them: ≈ 3% More squeezing between the SPs, more stretching outside
Chapter 22 · Lambert’s Conformal Chart 2
05
E-books by eatpl.in · © 2026 · Do not copy or distribute
Why does the separation of the standard parallels decide the scale error? The clip shows both charts. On the CAA half-million, the standard parallels are only 3 degrees apart: the cone hugs the Earth, and the error is about 0.1 percent. On the Jeppesen ED-6 they are 28 degrees apart: the cone sits well inside the Earth between them, so the surface is squeezed more there and stretched more outside. The error is about 3 percent.
Two convergences
Chart convergence and earth convergency
Definition Half of it is… Earth convergency Change in direction of a great circle between two meridians Conversion angle: GC to RL Chart convergence Change in direction of a straight line between two meridians on the chart Straight line to RL
CA = ½ ch long × sin mid lat
SL to RL = ½ ch long × sin origin
straight line ≈ great circle rhumb line ½ CC ½ CC Straight line to rhumb line = ½ chart convergence Rhumb line to great circle = conversion angle = ½ earth convergency Here ch long 40°: ½ CC = ½ × 40 × sin 45° = 14.1°
Chapter 22 · Lambert’s Conformal Chart 2
06
E-books by eatpl.in · © 2026 · Do not copy or distribute
Earth convergency is the difference in inclination of two meridians on the Earth, or the change in direction of a great circle between them. Chart convergence is the same for the chart: the angle between two meridians on the chart, or the change in direction of a straight line between them. The difference between a rhumb line and a great circle is the conversion angle, half the earth convergency: half change of longitude times sine mid latitude. The difference between a rhumb line and a straight line on the chart is half the chart convergence: half change of longitude times sine parallel of origin.
02
Lines on the chart
Curvature, mid-meridian, pros and cons.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: lines on the chart.
Great circle curvature
Why great circles bend away from the origin
Join two meridians 20° apart at 47°, 45° (origin) and 43°N.
Straight line to rhumb line: ½ CC = ½ × 20 × sin 45° = 7.071° in all three Great circle to rhumb line: CA = ½ × 20 × sin lat: 7.314° , 7.071° , 6.820° So the great circle is straight only at the origin, concave to it elsewhere
47°N ½CC 7.071° CA 7.314° GC bows north 45°N ½CC 7.071° CA 7.071° GC straight 43°N ½CC 7.071° CA 6.820° GC bows south 20° of longitude, parallel of origin 45°N Great circle deviation exaggerated ×20; rhumb line to scale Concave to the parallel of origin, on both sides
Chapter 22 · Lambert’s Conformal Chart 2
08
E-books by eatpl.in · © 2026 · Do not copy or distribute
The difference between chart and earth convergence explains why great circles are concave to the parallel of origin. Take two meridians 20 degrees apart and join them at 47, 45 and 43 north. The angle between the straight line and the rhumb line is half the chart convergence, half of 20 times sine 45: 7.071 degrees in all three cases. The angle between the great circle and the rhumb line is the conversion angle, half of 20 times sine of the latitude: 7.314 at 47, 7.071 at 45, 6.820 at 43. So at the origin the great circle and straight line coincide; at 47 the great circle bows north, at 43 south: concave to the parallel of origin either way.
The mid-meridian
All three lines are parallel there
Join two positions by a straight line, a great circle and a rhumb line: at the mid-meridian all three have the same direction.
Measure the rhumb line track at the mid-meridian
This is how rhumb line tracks are flown from a Lambert chart: the “mid-meridian” system.
mid-meridian Straight line, rhumb line, great circle between A and B All three are parallel where they cross the mid-meridian A B Great circle curvature exaggerated ×6
Chapter 22 · Lambert’s Conformal Chart 2
09
E-books by eatpl.in · © 2026 · Do not copy or distribute
If two positions on a Lambert chart are joined by a straight line, a great circle and a rhumb line, all three are parallel to each other at the mid-meridian, the meridian halfway between them in longitude. So to find the rhumb line track, measure the straight line’s direction at the mid-meridian. This is the mid-meridian system used to fly rhumb line tracks from a Lambert chart.
Advantages and disadvantages
The case for and against Lambert
Advantages Great circles: treat as straight lines Radio bearings plot without conversion angle (but NDBs need the meridian transfer) Small scale error: measure with a ruler
Disadvantages Compass flying gives rhumb lines: great circles need INS / IRS / FMS / GPS, or a gyro Rhumb lines are curves: use the mid-meridian Graticule not rectangular: plotting positions is harder NDB lines need meridian transfer
Chapter 22 · Lambert’s Conformal Chart 2
10
E-books by eatpl.in · © 2026 · Do not copy or distribute
Advantages: great circles can be treated as straight lines. Radio bearings are great circles, so they plot without conversion angle, though NDB bearings still need convergence allowed for by paralleling the aircraft’s meridian, with no calculation. If the scale error is small, a ruler measures distances. Disadvantages: flying by compass gives rhumb lines, so great circle tracks need automatic computation by INS, IRS, FMS or GPS, or steering by gyro. Rhumb line tracks need the mid-meridian system, because rhumb lines are curves. The graticule is not rectangular, so plotting positions is less simple than on a Mercator. And NDB position lines need meridian transfer.
03
Plotting
Radio bearings and straight-line tracks.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: plotting on a Lambert chart.
Where is the bearing measured?
Ground station or aircraft: that decides it
Measured at the ground station VDF (QDM, QTE) and VOR . The VOR bearing is encoded at the station; the aircraft only decodes it.
Variation at the STATION
Plot the true bearing from the station’s meridian . No conversion angle, no convergence.
Measured at the aircraft ADF / NDB and airborne weather radar .
Variation at the AIRCRAFT
Plot from a line through the NDB parallel to the aircraft’s meridian . That allows for chart convergence.
Chapter 22 · Lambert’s Conformal Chart 2
12
E-books by eatpl.in · © 2026 · Do not copy or distribute
Plotting on a Lambert chart is simpler than on a Mercator because radio waves are great circles, which are straight or nearly straight, so there is no conversion angle. But there may be convergence to allow for, depending on where the bearing is measured. VDF and VOR bearings are measured at the ground station: even a VOR bearing is encoded at the station and only decoded in the aircraft. Correct for variation at the station and plot the true bearing from the station. ADF and airborne weather radar bearings are measured at the aircraft, so use the aircraft’s variation and plot from a line through the NDB parallel to the aircraft’s meridian.
NDB bearings
Transfer the aircraft’s meridian
Heading 025°T + RBI 245° = 270°T to the NDB (at the aircraft) Reciprocal 090° from the NDB’s own meridian misses : the meridians converge Draw a line through the NDB parallel to the aircraft’s meridian and plot 090° from that From the NDB’s meridian, add or subtract the chart convergence
aircraft’s meridian NDB’s meridian heading 025°T 025 + 245 = 270° to the NDB 090° from the NDB’s meridian: misses parallel to aircraft’s meridian CC NDB 090° from the parallel line hits the aircraft
Chapter 22 · Lambert’s Conformal Chart 2
13
E-books by eatpl.in · © 2026 · Do not copy or distribute
An aircraft heading 025 true measures an NDB at 245 relative, so the true great circle bearing of the NDB from the aircraft is 270. But if you plot the reciprocal, 090, from the NDB’s own meridian, the line misses the aircraft, because the two meridians are not parallel on the chart. Instead draw a line through the NDB parallel to the aircraft’s meridian and measure 090 from that: the line passes through the aircraft. This allows for chart convergence automatically and is the method always used. Measured from the NDB’s meridian, the bearing here is 090 minus the chart convergence.
NDB bearings in 3D
From the globe to the chart
The ADF measures the bearing at the aircraft, against the aircraft’s meridian On the globe and on the chart the NDB’s meridian points a different way So plot the reciprocal from a line through the NDB parallel to the aircraft’s meridian
Chapter 22 · Lambert’s Conformal Chart 2
14
E-books by eatpl.in · © 2026 · Do not copy or distribute
The same idea on the real Earth. The aircraft’s ADF measures the NDB on 270 degrees, against the aircraft’s own meridian. The NDB’s meridian points a different way, because the meridians converge towards the pole. Opened onto a Lambert chart the meridians are straight but still converge, and the radio great circle is nearly straight. So we draw a line through the NDB parallel to the aircraft’s meridian, and plot the reciprocal, 090, from that line. It passes through the aircraft.
Worked example
NH. Heading 330°(T), NDB at 090°(R). Chart convergence 3°.
330 + 090 = 060°T : the great circle bearing of the NDB from the aircraft (a) Plot 240° from a line through the NDB parallel to the aircraft’s meridian (b) From the NDB’s own meridian: 240 + 3 = 243° From the parallel line
240°
From the NDB meridian
243°
Which way? NDB to the east (NH): its meridian leans towards the aircraft’s at the top, so bearings from it are larger by CC.
Chapter 22 · Lambert’s Conformal Chart 2
15
E-books by eatpl.in · © 2026 · Do not copy or distribute
A worked example. In the northern hemisphere, heading 330 true, an NDB bears 090 relative. The true great circle bearing of the NDB from the aircraft is 330 plus 090, 060. So plot 240 from a line through the NDB parallel to the aircraft’s meridian. If you need it from the NDB’s own meridian, it is 240 plus the 3 degrees of chart convergence, 243. Remember: for bearings measured at the aircraft, the true heading uses the variation at the aircraft.
Example 1 · Straight-line tracks
Straight line A→B is 250°(T) at A. CC 6°. NH.
Straight line to rhumb line = ½ CC = 3° (a) Westbound in the NH, the straight line’s direction falls: RL = 250 − 3 = 247°(T) (b) RL of A from B = 247 − 180 = 067° Straight line at B, back to A: 067 − 3 = 064°(T) GC bearing of A from B
064°(T)
The pattern The rhumb line is the straight line’s direction at the mid-meridian: halfway between its directions at A and B (250° and 244°).
Chapter 22 · Lambert’s Conformal Chart 2
16
E-books by eatpl.in · © 2026 · Do not copy or distribute
Example 1. A straight line on a Lambert chart from A to B measures 250 true from A’s meridian, and the chart convergence between A and B is 6 degrees. The angle between the straight line and the rhumb line is half the chart convergence, 3 degrees. Going west in the northern hemisphere the straight line’s direction decreases, so the rhumb line is 247. The rhumb line of A from B is the reciprocal, 067, and the straight line at B, the approximate great circle bearing of A from B, is 064.
Example 2 · Straight-line tracks
Straight line A→B: 300°(T) at the mid-meridian, 302°(T) at A. NH.
(a) Rhumb line Rhumb line and straight line are parallel at the mid-meridian.
RL A → B = 300°(T)
(b) Chart convergence Straight line at A 302°, rhumb line 300°.
½ CC = 2° → CC = 4°
(c) GC bearing of A from B RL of A from B = 120°; less ½ CC.
120 − 2 = 118°(T)
Chapter 22 · Lambert’s Conformal Chart 2
17
E-books by eatpl.in · © 2026 · Do not copy or distribute
Example 2. The straight line from A to B crosses the mid-meridian on 300 true and measures 302 at A. The rhumb line is parallel to the straight line at the mid-meridian, so the rhumb line track is 300. The straight line at A differs from it by 2 degrees, half the chart convergence, so the chart convergence is 4. The rhumb line of A from B is 120, and the straight line at B, the approximate great circle bearing of A from B, is 118.
Summary
Lambert chart 2 on one page
Topic Remember Constant scale ≤1% error with standard parallels up to ~16° apart (CAA 1:500,000 ≈ 0.1%; ED-6 ≈ 3%) Two convergences Straight line to RL = ½ CC = ½ ch long × sin origin; GC to RL = CA = ½ ch long × sin mid lat Great circles Straight at the origin, concave to it elsewhere: the CA differs from ½ CC Mid-meridian Straight line, GC and RL all parallel there: measure the RL track at the mid-meridian VOR / VDF Measured at the station: station variation; plot from the station’s meridian NDB / AWR Measured at the aircraft: aircraft variation; plot from a parallel of the aircraft’s meridian through the NDB Straight-line track NH: direction rises going east, falls going west by CC; SH the reverse
Chapter 22 · Lambert’s Conformal Chart 2
18
E-books by eatpl.in · © 2026 · Do not copy or distribute
The summary. Lambert scale is within 1 percent for standard parallels up to about 16 degrees apart. Straight line to rhumb line is half the chart convergence; rhumb line to great circle is the conversion angle. Great circles are straight at the origin and concave to it elsewhere. All three lines are parallel at the mid-meridian. VOR and VDF bearings use station variation and plot from the station; NDB bearings use aircraft variation and plot from a parallel of the aircraft’s meridian. In the northern hemisphere a straight line’s direction increases going east by the chart convergence.
Practice · Questions 1–3
Scale and straight-line tracks
1. A Lambert chart covers 29°N to 45°N, standard parallels 31°N and 43°N, convergency ch long × 0.6. Is the scale at 43°N the same, greater or less than at (i) 45°N (ii) 37°N (iii) 31°N?
2. Same chart. A straight line from A (40°N 12°E) to C at 18°W passes through B. Its direction is 292°(T) at A and 283°(T) at B. (a) Longitude of B? (b) Approximate rhumb line track (i) at A (ii) at B?
3. Chart 42°S to 64°S, convergency ch long × 0.8. A straight line from K (48°S 178°E) to M at 152°W passes through L. Direction 102°(T) at K, 096°(T) at L. (a) Longitude of L? (b) Approx RL K to M? (c) Approx RL K to L? (d) Latitude of M?
Chapter 22 · Lambert’s Conformal Chart 2
19
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 1 to 3 from the end of Chapter 22. The Lambert Plotting Lab sets up every one.
Practice · Questions 4–9
Cone constant, scale and tracks
4. Standard parallels 63°N and 41°N. Constant of the cone? (a) .891 (b) .788 (c) .656 (d) .707
5. Scale on a Lambert chart: (a) is constant (b) is constant along a meridian (c) varies slightly with latitude and longitude (d) is constant along a parallel
6. Standard parallels 41°20′N and 11°40′N. Constant of the cone? (a) .660 (b) .202 (c) .446 (d) .895
7. Scale on a Lambert chart is: (a) constant along a line of latitude (b) constant along a line of longitude (c) constant everywhere (d) correct at the parallel of origin
8. Constant of the cone .78585. Parallel of tangency? (a) 51°02′ (b) 51°36′ (c) 51°15′ (d) 51°48′
9. Constant of the cone 0.80. A is 53N 04W. Initial straight-line track to B 070°(T); rhumb line A to B 082°(T). Longitude of B? (a) 26E (b) 34W (c) 11E (d) 15E
Chapter 22 · Lambert’s Conformal Chart 2
20
E-books by eatpl.in · © 2026 · Do not copy or distribute
Practice · Answers
Answers and working
Q Answer Working 1 (i) less (ii) greater (iii) same 45° is outside the SPs (expanded); 37° is the origin (least); 31° is a standard parallel 2 (a) 003°00′W (b) 283° and 283° CC 9° = 0.6 × ch long → 15° west of A; B is on the mid-meridian of A–C (12E to 18W) 3 (a) 174°30′W (b) 090° (c) 099° (d) 48°S CC 6° → 7.5° east; K–M CC 24°: 102 − 12; K–L: 102 − 3; RL 090° → same latitude 4 b · .788 Origin 52°: sin 52° 5 d Constant along a parallel 6 c · .446 Origin 26°30′: sin 26.5° 7 a Constant along a line of latitude 8 d · 51°48′ sin⁻¹ 0.78585 9 a · 26E ½ CC = 12° → CC 24° = 0.8 × 30°; east of 04W
Chapter 22 · Lambert’s Conformal Chart 2
21
E-books by eatpl.in · © 2026 · Do not copy or distribute
Try it yourself
Lambert Plotting Lab
Every answer drawn on a 3D cone you can unroll, or the 2D chart Straight-line tracks: directions, rhumb line, longitude, mid-meridian VOR and NDB bearings: which variation, which meridian Cone constant, parallel of origin and scale error All 9 practice questions, one tap each Open the Lambert Plotting Lab →
mid-meridian straight line, rhumb line: parallel at the mid-meridian
Chapter 22 · Lambert’s Conformal Chart 2
22
E-books by eatpl.in · © 2026 · Do not copy or distribute
The Lambert Plotting Lab solves straight-line track problems, plots VOR and NDB bearings with the right variation and meridian, works out the cone constant, parallel of origin and scale error, and sets up all nine practice questions.
Straight line / line to plot
Rhumb line
Meridians, standard parallels
Loading Earth…
2D chart 3D cone
eatpl.in · General Navigation · Chapter 22
Lambert Plotting Lab
Straight line to rhumb line = ½ chart convergence; all three lines are parallel at the mid-meridian. NDB bearings: plot from a parallel of the aircraft’s meridian.
Straight-line track
Radio bearing
Cone & scale
Practice
The questions from the end of Chapter 22. Set up enters the question and works it; Answer shows the answer.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.