General Navigation · Chapter 30
Plotting
Position lines, fixes and the bearings behind them: VOR, VDF, NDB, radar and DME, and how to plot them on a Lambert chart.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter 30 covers plotting: the equipment and symbols, position lines and fixes, bearings measured at a ground station and at the aircraft, relative to true bearings, DME fixes and the cocked hat, climb and descent, and plotting on a Lambert chart, where convergence matters for ADF bearings.
Chapter roadmap
What this chapter covers
01
Basics Equipment, definitions, symbols, track made good.
02
Position lines Measured at the station (VOR, VDF) or the aircraft (ADF, radar).
03
Fixes DME, the cocked hat, climb and descent.
04
Lambert plotting Tracks, positions, and convergence for ADF.
Chapter 30 · Plotting
02
E-books by eatpl.in · © 2026 · Do not copy or distribute
Four parts: the basics of plotting; position lines measured at a ground station and at the aircraft; fixes from DME and three position lines, with climb and descent problems; and plotting on a Lambert chart, where an ADF bearing needs care because of convergence. Then the chapter questions and the Plotting Lab.
Introduction
Between the 1 in 60 rule and the glass cockpit
The aircraft More than a light trainer, less than a full glass-cockpit airliner: VOR, DME, ADF and a slaved gyro compass .
You fix position by plotting on a chart.
The charts A radio navigation or plotting chart: usually Lambert (EASA), occasionally polar stereographic.
Exam questions use the Jeppesen E(LO)1 and 1a , supplied with the exam.
The kit Navigation computer, straight-edge, square plotting protractor, dividers, 2H and HB pencils, soft eraser.
Plot in True , recording the time of every position line and fix.
Chapter 30 · Plotting
03
E-books by eatpl.in · © 2026 · Do not copy or distribute
There are two styles of navigation you know already: solo VFR with the 1 in 60 rule, and automatic systems such as INS, GPS and FMS. In between are aircraft fitted with VOR, DME, ADF and slaved gyro compasses, where you fix position by plotting on a radio navigation or plotting chart: for EASA, usually the Lambert, occasionally the polar stereographic. Exam questions use the Jeppesen E(LO)1 and 1a charts. You need a computer, a straight-edge, a square protractor, dividers and pencils, and you normally plot in True.
01
Basics
Definitions, symbols and the track made good.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Definitions
The Q codes and the words of plotting
Term Meaning QTE True bearing of the aircraft FROM the station QDR Magnetic bearing of the aircraft FROM the station (= VOR radial) QDM Magnetic track from the aircraft TO the station (QDR ± 180) Position line A line somewhere along which the aircraft was at a given time Fix · pinpoint Position from radio or radar · position from map reading Heading Where the nose points: Hdg(C) + dev = Hdg(M) + var = Hdg(T) Isogonal · convergency Line of equal variation · angle between two meridians at a latitude
Chapter 30 · Plotting
05
E-books by eatpl.in · © 2026 · Do not copy or distribute
Some definitions. QTE is the true bearing of the aircraft from a direction-finding station; QDR the magnetic bearing of the aircraft from the station, which is what a VOR radial is; QDM the magnetic track from the aircraft to the station, the reciprocal of the QDR. A position line is a line along which the aircraft was at a particular time; two at the same time give a fix. A pinpoint is a position from map reading. Heading may be compass, magnetic or true: apply deviation and variation to get true. An isogonal joins places of equal variation, and convergency is the angle between two meridians.
Symbols and the track made good
Two fixes, one heading: the line between them is the TMG
Use the standard symbols and always write the time Two position lines at the same time give a fix One heading flown between two fixes: the line joining them is the track made good Distance along it ÷ time = actual groundspeed 100 nm in 30 minutes: groundspeed 200 kt
1000 fix 1030 fix TMG 068°(T) · 100 nm 100 nm in 30 min → groundspeed 200 kt 1115 1121 1510 station
Chapter 30 · Plotting
06
E-books by eatpl.in · © 2026 · Do not copy or distribute
Use the standard symbols and always record the time. A position line is drawn with an arrowhead and its time; two position lines at the same time give a fix, drawn as a circle; a radar fix is a triangle; and a radio facility has its own symbol. If one heading has been flown between two fixes, the straight line joining them is the track made good, which you measure with the protractor, and the distance along it divided by the time gives the actual groundspeed: 100 miles in 30 minutes is 200 knots.
02
Position lines
Where the bearing is measured decides the variation.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: position lines.
Measured at the ground station
VDF and VOR: use the STATION’S variation
VDF The station measures the direction of your transmission: a QTE . It applies its own variation to give QDR, then ±180 for QDM.
QTE (station measures) 140°(T) Station variation 10°W QDR 150°(M) ± 180 180 QDM 330°(M)
Plotting a VOR radial The bearing is encoded at the station : use station variation .
1. Align the protractor with the chart’s magnetic arrow (short, so inaccurate).
2. Better: lay off the variation at the VOR from the nearest meridian to make your own magnetic north.
3. Or align the protractor with the printed airway radials (e.g. SHA 052, 071, 080, 115, 173°M).
Or convert to true and plot from the meridian.
Chapter 30 · Plotting
08
E-books by eatpl.in · © 2026 · Do not copy or distribute
Radio waves follow great circles, so all radio bearings are great-circle bearings. With VDF the ground station measures the direction of your transmission, a QTE, applies its own variation to give the QDR, and adds or subtracts 180 for the QDM: 140 true, 10 west, QDR 150, QDM 330. With VOR the bearing is also determined at the ground station, so again station variation is used. To plot a radial, align the protractor with the magnetic arrow, or better, lay off the variation at the VOR from the nearest meridian, or align with the printed airway radials; or convert to true and plot from the meridian.
A VOR fix in 3D
Two radials and two DME ranges over Ireland
SHA radial 120°M , variation 8°W at the station: plot 112°T CRK radial 033°M : plot 025°T They cross at 5230N 00800W (question 10) CRN 18 DME and SHA 20 DME cross twice: heading 270°M with ranges decreasing picks the eastern one
Chapter 30 · Plotting
09
E-books by eatpl.in · © 2026 · Do not copy or distribute
Over a real chart of Ireland: Shannon VOR radial 120 magnetic, with 8 west variation at the station, is plotted as 112 true; the Cork radial 033 magnetic is 025 true; they cross at 52 30 north 8 west, the answer to question 10. Then two DME ranges, 18 miles from Connaught and 20 from Shannon: the circles cross in two places, and the heading and the fact that both ranges are decreasing tell you which, here the eastern one, question 6.
Relative to true
Heading + relative bearing = true bearing
ADF on an RBI and airborne weather radar give relative bearings, from the nose Mag heading + aircraft variation = true heading True heading + relative bearing = true bearing TO the NDB Reciprocal: the true bearing to plot FROM the NDB On an RMI the bearing is already magnetic: just apply aircraft variation
True N NDB Hdg 030°(T) 060° relative 030 + 060 = 090°(T) to the NDB Heading + relative bearing = true bearing (over 360? subtract 360) RBI reading 207 Mag heading 315°(M) Aircraft var 9°W use AIRCRAFT variation True heading 306°(T) + relative 207 True bearing TO 513 − 360 = 153°(T) Plot FROM the NDB 333°(T) reciprocal Example: RBI 207, heading 315°(M), NDB var 7°W, aircraft var 9°W NDB variation (7°W) is not used: the bearing was measured at the aircraft
Chapter 30 · Plotting
10
E-books by eatpl.in · © 2026 · Do not copy or distribute
An ADF on a relative bearing indicator, and an airborne weather radar, measure bearings relative to the aircraft’s nose. Convert the heading to true with the variation at the aircraft, add the relative bearing for the true bearing to the NDB, subtracting 360 if needed, and take the reciprocal to plot from the NDB. In the example, RBI 207 on a heading of 315 magnetic with 9 west at the aircraft: true heading 306, true bearing to the NDB 513 minus 360, 153, so plot 333 from the NDB. The NDB’s own variation is not used. An RMI shows a magnetic bearing already: just apply the aircraft’s variation.
Measured at the aircraft
ADF and airborne weather radar: use the AIRCRAFT’S variation
ADF The aircraft’s receiver measures the bearing of the NDB from the nose.
RBI : relative bearing · RMI : magnetic bearing (the compass card does the adding).
AWR in MAP mode A cosecant² beam paints the ground: ranges and relative bearings of headlands and islands.
True heading + relative = bearing TO the return; reciprocal to plot FROM it.
Why aircraft variation? These bearings are turned into magnetic or true by the aircraft’s compass , which senses the variation where the aircraft is .
Chapter 30 · Plotting
11
E-books by eatpl.in · © 2026 · Do not copy or distribute
Bearing measured at Examples Variation to use Convergence (Lambert) the ground station VOR, VDF (QDM, QDR, QTE) at the station none: plot from the station meridian the aircraft ADF (RBI, RMI), AWR at the aircraft allow for it: plot from a parallel to the aircraft’s meridian
03
Fixes
DME, three position lines, climb and descent.
E-books by eatpl.in · © 2026 · Do not copy or distribute
DME and the cocked hat
Two ranges cross twice; three lines make a hat
DME gives slant range; beyond about 10 nm treat it as plan range (unless very high) VOR bearing + DME range: one fix Two DME ranges cross twice : use your heading and whether the ranges are increasing or decreasing Three position lines make a cocked hat : fix where the bisectors meet; its size shows the accuracy
DME 1 DME 2 A B Heading 270°, ranges decreasing → B from A, flying west, both would increase Fix where the angle bisectors meet small hat = good fix
Chapter 30 · Plotting
13
E-books by eatpl.in · © 2026 · Do not copy or distribute
DME gives slant range; strictly it should be converted to plan range, but beyond about 10 miles the difference is insignificant unless you are very high. A VOR bearing with a DME range gives a single fix. Two DME ranges cross in two places; the question will tell you your heading and whether the ranges are increasing or decreasing, which picks one: heading west with both decreasing, you must be on the eastern side. Three position lines usually form a triangle, the cocked hat: take the fix where the bisectors of its angles meet. The smaller the hat, the better the fix.
Climb and descent
Make the vertical time equal the horizontal time
Height to change ÷ rate = distance ÷ groundspeed 1. 65 nm out, FL330 → FL100 over the VOR, GS 240: 1415 ft/min 2. 7500 → 1000 ft by 6 DME, GS 156, ROD 800: 6500 ÷ 800 = 8.125 min = 21.1 nm; start at 27.1 nm Remember to add the distance where you must already be level
65 50 40 30 20 10 0 nm to the VOR FL100 FL200 FL330 VOR 65 nm at 240 kt = 16.25 min · 23 000 ft to lose in the same time ROD = 23 000 ÷ 16.25 = 1415 ft/min → (a) 1420 Time vertically = time horizontally
Chapter 30 · Plotting
14
E-books by eatpl.in · © 2026 · Do not copy or distribute
Climb and descent problems make the time taken vertically equal to the time taken horizontally. Example 1: 65 miles from a VOR at FL330, to cross it at FL100 at a mean groundspeed of 240 knots. 65 miles at 240 knots takes 16.25 minutes; 23,000 feet in 16.25 minutes is 1415 feet per minute, answer a. Example 2: descend from 7500 feet to 1000 feet by 6 DME at 156 knots and 800 feet per minute. 6500 feet takes 8.125 minutes, covering 21.1 miles; add the 6 miles: start at 27.1 miles.
04
Lambert plotting
Convergence matters for ADF.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part four: plotting on a Lambert chart.
Lambert and polar stereo charts
Straight lines are great circles; the graticule is not square
Measuring a track Join A and B with a straight line (a great circle) and measure it at the mid-meridian : the rhumb-line track.
Plotting a heading or track Lay it off from the nearest meridian to where it starts; ignore the small error.
Measuring distance Scale is not quite constant: use the latitude scale locally .
Plotting a position Mark the longitude on the scales north and south, join them with the straight-edge, then step the latitude along it with dividers.
Chapter 30 · Plotting
16
E-books by eatpl.in · © 2026 · Do not copy or distribute
On a Lambert chart, or a polar stereographic at high latitude, a straight line is in practice a great circle. To measure a track between two points, join them and measure at the mid-meridian, giving the mean rhumb-line track. To plot a heading or track, lay it off from the nearest meridian. Scale is not quite constant, so measure distance on the latitude scale locally. And because the graticule is not rectangular, plot a position by marking the longitude on the scales to the north and south, joining them with a straight-edge, and stepping off the latitude along it.
An ADF bearing in 3D
Measured at the aircraft, plotted from the NDB
Heading 025°(T) + RBI 245° = 270°(T) to the NDB, measured at the aircraft The reciprocal 090° laid off from the NDB’s own meridian misses the aircraft The meridians converge: lay off 090° from a line parallel to the aircraft’s meridian Or from the NDB meridian: 090° − convergence
Chapter 30 · Plotting
17
E-books by eatpl.in · © 2026 · Do not copy or distribute
An ADF bearing is measured at the aircraft but has to be plotted from the NDB. Heading 025 true plus a relative bearing of 245 gives 270 true to the NDB. If you plot the reciprocal, 090, from the NDB’s own meridian, the line misses the aircraft, because at high latitude the meridians converge. Lay off the 090 from a line through the NDB parallel to the aircraft’s meridian, which allows for convergence automatically; measured from the NDB’s meridian it is 090 minus the convergence.
Plotting an ADF bearing
Lay it off from a parallel to the aircraft’s meridian
VOR, VDF: measured at the station: plot the true bearing from the station meridian ADF, AWR: measured at the aircraft, so draw through the NDB a line parallel to the aircraft’s meridian and lay off from that Rule of thumb: ch long 2° or more, use the parallel; under 2°, plot from the NDB meridian
aircraft meridian NDB meridian NDB aircraft 270°(T) to the NDB 090° from the NDB meridian: misses (a) parallel to aircraft meridian 090° from the parallel: through the aircraft (b) = 090° − 15° convergence from the NDB meridian (convergence exaggerated) hdg 330°(T) + 090°R = 060°: plot 240° from the parallel; 240 + 3 = 243° from the NDB meridian
Chapter 30 · Plotting
18
E-books by eatpl.in · © 2026 · Do not copy or distribute
On a Lambert chart radio great circles are straight lines, so there is no conversion angle, but there may be convergence. A VOR or VDF bearing is measured at the station: plot the true bearing from the station meridian. An ADF or radar bearing is measured at the aircraft, so it is relative to the aircraft’s meridian; plotting the reciprocal from the NDB meridian misses, as in figure a. Draw through the NDB a line parallel to the aircraft’s meridian and lay off from that, figure b; from the NDB meridian it is the reciprocal minus the convergence. In the example, heading 330 and 090 relative give 060, so plot 240 from the parallel, or 243 from the NDB meridian with 3 degrees of convergence. In practice, if the change of longitude is 2 degrees or more, use the parallel.
Summary
Plotting in six lines
Topic Remember Q codes QTE true from the station · QDR magnetic from (= radial) · QDM magnetic to (QDR ± 180) Variation Measured at the station (VOR, VDF): station var · at the aircraft (ADF, AWR): aircraft var Relative bearings Hdg(T) + relative = true bearing TO; reciprocal to plot FROM Fixes TMG and GS from two fixes · DME ambiguity: heading and increasing/decreasing · cocked hat: bisectors Climb / descent Height ÷ rate = distance ÷ groundspeed (allow for where you must be level) Lambert Track at mid-meridian; plot from nearest meridian; local lat scale; ADF from a parallel to the aircraft meridian
Chapter 30 · Plotting
19
E-books by eatpl.in · © 2026 · Do not copy or distribute
In summary: QTE is true from the station, QDR magnetic from it, QDM magnetic to it. Bearings measured at the ground station use station variation; those measured at the aircraft use aircraft variation. Heading plus relative bearing gives the true bearing to the station; take the reciprocal to plot. Two fixes give the track made good and groundspeed; DME ambiguity is resolved by heading and range trend; the cocked hat fix is where the bisectors meet. Climb and descent: vertical time equals horizontal time. On a Lambert, measure tracks at the mid-meridian and plot ADF bearings from a parallel to the aircraft’s meridian.
Questions 1–5
Questions: set 1 (Jeppesen charts)
1. Average magnetic course and distance from 6000N 02000W to Sumburgh VOR? (a) 095, 562 (b) 095, 468 (c) 105, 562 (d) 105, 468
2. Average true track and distance from WTD NDB (5211.3N 00705.0W) to FOY NDB (5234.0N 00911.7W)? (a) 294, 76 (b) 286, 76 (c) 294, 81 (d) 286, 81
3. Heading 105°(C), deviation 3°E. WTD NDB bears 013°R; CRK VOR (5150.4N 00829.7W) QDM 211°. Position? (a) 5245N 00757W (b) 5228N 00802W (c) 5412N 00639W (d) 5217N 00745W
4. The airport at 5211N 00932W is: (a) Kerry (b) Cork (c) Shannon (d) Waterford
5. At 5211N 00931W on E(LO)1 the symbols are: (a) military airport, ILS, NDB (b) civil airport, VOR, ILS (c) military airport, VOR, ILS (d) civil airport, ILS, NDB
Chapter 30 · Plotting
20
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions set 1. They use the Jeppesen E(LO)1 chart; the lab has the stations on a real chart of Ireland.
Questions 6–10
Questions: set 2 (Jeppesen E(LO)1)
6. CRN (5318N 00857W) 18 DME, SHA (5243N 00853W) 20 DME, heading 270°M, both ranges decreasing. Position? (a) 5201N 00908W (b) 5301N 00908W (c) 5302N 00843W (d) 5203N 00843W
7. What is at 5211N 00932W? (a) Kerry VOR (b) Cork airport (c) Waterford NDB (d) Kerry airport
8. Mean true track and distance BAL VOR (5318N 00627W) to CFN NDB (5502N 00820W)? (a) 328°, 125 (b) 148°, 125 (c) 328°, 134 (d) 148°, 134
9. At 5340N 00800W, the QDR from SHA VOR (5243N 00853W)? (a) 217 (b) 037 (c) 209 (d) 029
10. SHA radial 120°(M); CRK (5151N 00830W) radial 033°(M). Position? (a) 5320N 00800W (b) 5240N 00821W (c) 5220N 00821W (d) 5230N 00800W
Chapter 30 · Plotting
21
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions set 2. Questions 11 to 15 of this set need a printed chart, so they are not included here.
Answers
Answers, checked by calculation (variation in Ireland 8°W)
Q Working Answer 1 Great circle 560 nm, mean true track 091°; with about 14°W mean variation, 105°(M) (c) 105, 562 2 Mean (mid-meridian) track 286°(T), 80.6 nm (d) 286, 81 3 105(C) + 3E = 108(M) − 8W = 100(T); WTD bears 113(T); CRK radial 031(M) = 023(T); lines cross (b) 5228N 00802W 4 · 5 · 7 Kerry airport: civil airport with ILS and NDB (a) · (d) · (d) 6 Circles cross at 5301N 00908W and 5302N 00843W; heading west, both decreasing → the eastern one (c) 5302N 00843W 8 Mean track 328°(T), 123 nm (chart: 125) (a) 328°, 125 9 True bearing from SHA 029°(T) + 8°W = 037°(M) (b) 037 10 120(M) = 112(T) from SHA; 033(M) = 025(T) from CRK; cross at 5230N 00800W (d) 5230N 00800W
Chapter 30 · Plotting
22
E-books by eatpl.in · © 2026 · Do not copy or distribute
Answers with working, checked by spherical calculation using the station positions; the variation over Ireland on the chart is about 8 west.
Try it yourself
Plotting Lab
A Lambert chart of Ireland with the E(LO)1 stations Fix from two position lines: VOR radial, QDM, QTE, NDB (RBI or RMI) or DME Every conversion shown: variation, relative to true, convergence Climb and descent, track made good and groundspeed Questions 1–10 and the worked examples set up Open the Plotting Lab →
Chapter 30 · Plotting
23
E-books by eatpl.in · © 2026 · Do not copy or distribute
The Plotting Lab draws a Lambert chart of Ireland with the E(LO)1 stations, plots a fix from any two position lines (VOR radials, QDMs, QTEs, NDB bearings from an RBI or RMI, or DME ranges), shows every conversion, works climb and descent and track made good problems, and sets up the chapter questions.
Loading Earth…
Chart 3D globe
Position line 1
Position line 2
Fix
Stations
eatpl.in · General Navigation · Chapter 30
Plotting Lab
Fix your position from two position lines on a Lambert chart of Ireland, with the Jeppesen E(LO)1 stations; plus track made good and climb and descent.
Fix
Track & descent
Practice
The chapter questions 1–10 (Jeppesen E(LO)1 stations; variation over Ireland about 8°W) and its worked examples. Set up fills in the lab; Answer shows the answer.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute. Coastline: Natural Earth (public domain).