General Navigation · Chapter 33
Aircraft Magnetism
Hard iron, soft iron and the compass swing: why the compass needle does not quite point to magnetic north.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter 33 covers aircraft magnetism: deviation, the compass swing, hard iron and vertical soft iron magnetism, coefficients A, B and C and their correction, accuracy limits, the effect of a change of magnetic latitude, and the occasions for swinging the compass.
Chapter roadmap
What this chapter covers
01
Deviation What it is, how it is named, and the compass swing.
02
Hard and soft iron Permanent and induced magnetism; the sine and cosine curves.
03
Coefficients A, B and C: finding them, correcting them, limits.
04
Latitude and swings Why deviation changes with latitude; when to swing.
Chapter 33 · Aircraft Magnetism
02
E-books by eatpl.in · © 2026 · Do not copy or distribute
Four parts: deviation and the compass swing; hard and soft iron magnetism; coefficients A, B and C and their correction; and the effect of magnetic latitude and the occasions for swinging the compass. Then the chapter questions and the Compass Swing Lab.
01
Deviation
The aircraft’s own magnetism.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part one: deviation and the compass swing.
Deviation
The needle is pulled off magnetic north
Deviation : the angle between the compass needle and the magnetic meridian East (+) if the north-seeking end lies east of magnetic north; West (−) if westMagnetic = Compass + Deviation Deviation West, Compass Best · Deviation East, Compass Least
magnetic north mag 090 compass 095 5°W mag 095 compass 090 5°E deviation drawn ×3 Deviation West, Compass Best Compass heading 095°C Deviation 5°W (−5) Magnetic heading 090°M Deviation East, Compass Least Compass heading 090°C Deviation 5°E (+5) Magnetic heading 095°M Magnetic = Compass + Deviation East is +, West is − green magnetic red compass small arc deviation
Chapter 33 · Aircraft Magnetism
04
E-books by eatpl.in · © 2026 · Do not copy or distribute
The compass needle would lie along the magnetic meridian but for the aircraft’s own magnetism. Deviation is the angle between the direction the compass needle takes up and the magnetic meridian. It is named east, plus, when the north-seeking end lies east of magnetic north, and west, minus, when it lies west. Magnetic heading equals compass heading plus deviation: so with 5 degrees west the compass reads 095 on 090 magnetic, deviation west, compass best; with 5 east it reads 090 on 095 magnetic, deviation east, compass least.
The compass swing
Compare with a datum compass on each heading
On the compass swinging base , away from other magnetic influence Compare the aircraft compass with a landing (datum) compass on a series of headings Aims: find the deviations, correct as much as possible, record the residual Deviations resolve into coefficients A, B and C
Chapter 33 · Aircraft Magnetism
05
E-books by eatpl.in · © 2026 · Do not copy or distribute
The basic method of finding deviation is to compare the aircraft compass with magnetic heading from a high-quality landing or datum compass, on a site chosen for the purpose: the compass swinging base. The aims are to find the deviation between magnetic and compass north on a series of headings, to correct or remove as much as possible, and to record the residual deviation left after adjustment. The deviations come from hard and soft iron magnetism and are resolved into coefficients A, B and C. Here A is the mean of all eight, B half the difference between east and west, C half the difference between north and south.
02
Hard and soft iron
Permanent and induced.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: hard iron and vertical soft iron magnetism.
Hard and soft iron
Permanent magnetism and magnetism induced by the Earth
Hard iron : permanent magnetism, resolved into three components fixed in the aircraft; they do not change with headingSoft iron : magnetism induced by surrounding fields, mainly the Earth’sWe consider only vertical soft iron (VSI) , magnetised by Z Z is zero at the magnetic equator, so no VSI there; it grows towards the poles
Hard iron: permanent Vertical soft iron: induced by Z P Q R ⊙ P fore-and-aft · Q athwartships · R vertical fixed in the aircraft: they turn with it do not change with heading or latitude magnetic equator Z = 0 35°N Z 70°N Z Z magnetises vertical soft iron none at the equator, more towards the poles same on every heading; changes with latitude a vertical rod of soft iron in the aircraft
Chapter 33 · Aircraft Magnetism
07
E-books by eatpl.in · © 2026 · Do not copy or distribute
Hard iron magnetism is permanent. The total force at the compass from hard iron can be resolved into three components, fore and aft, athwartships and vertical, fixed for a given aircraft: they do not change with heading. Soft iron magnetism is induced in the structure by surrounding fields, the most important being the Earth’s. Within the syllabus we consider only vertical soft iron, magnetised by Z, the vertical component of the Earth’s field. Z is zero at the magnetic equator, so no VSI magnetism is induced there, and increases towards the magnetic poles.
Coefficients B and C in 3D
A blue pole in the nose, then on the right wing
Blue pole in the nose: deviation is a positive sine curve, coefficient B Max easterly on 090°, westerly on 270°, zero on N and S Blue pole on the right wing: a positive cosine curve, coefficient C A pole aft or on the left wing gives the negative curve
Chapter 33 · Aircraft Magnetism
08
E-books by eatpl.in · © 2026 · Do not copy or distribute
Put an imaginary blue pole in the nose. Heading north it pulls with the Earth’s field and there is no deviation. Turning right it pulls the red end of the needle east, most on 090, and back to zero on 180; on the westerly headings it pulls the needle west, most on 270. Plotted against compass heading this is a positive sine curve: coefficient B, the component along the fore and aft axis. A blue pole on the right wing gives a positive cosine curve: coefficient C. A pole aft, or on the left wing, gives the negative curves.
Blue pole in the nose
Deviation and directive force round the compass
°C Deviation Directive force 000 zero maximum 045 East + some more than earth’s 090 East + max earth’s approx. 135 East + some less than earth’s 180 zero minimum 225 West − some less than earth’s 270 West − max earth’s approx. 315 West − some more than earth’s
N E S W heading 000°C deviation zero directive force Earth’s H alone heading 045°C deviation East +11° directive force Earth’s H alone heading 090°C deviation East +19° directive force Earth’s H alone heading 135°C deviation East +18° directive force Earth’s H alone heading 180°C deviation zero directive force Earth’s H alone heading 225°C deviation West −18° directive force Earth’s H alone heading 270°C deviation West −19° directive force Earth’s H alone heading 315°C deviation West −11° directive force Earth’s H alone arrows at the compass Earth’s field H pull of the blue pole resultant: the needle
Chapter 33 · Aircraft Magnetism
09
E-books by eatpl.in · © 2026 · Do not copy or distribute
The table for a blue pole in the nose. Heading north it pulls with the Earth’s field: no deviation and maximum directive force. On 090 the deviation is a maximum easterly; on 180 it pulls against the stronger Earth field, no deviation but minimum directive force; on 270 a maximum westerly. With the pole aft, the curve is negative and the directive force is greatest on 180 and least on 360.
03
Coefficients
A, B and C.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: coefficients A, B and C, correction and limits.
Adding the coefficients
A constant, a sine and a cosine
A : constant on every heading (mainly a misaligned lubber line)B : fore-and-aft force, a sine curve: max on 090/270C : athwartships force, a cosine curve: max on 000/180Their sum is the deviation curve found in the swing
000 045 090 135 180 225 270 315 360 -6 -4 -2 +2 +4 +6 E W A = +1 B sin = +4 sin C cos = −2 cos total deviation deviation = A + B sin(heading) + C cos(heading)
Chapter 33 · Aircraft Magnetism
11
E-books by eatpl.in · © 2026 · Do not copy or distribute
The deviation found in a swing can be resolved into a constant, coefficient A, which is the same on every heading and is mainly a mechanical error such as a misaligned lubber line; coefficient B, from forces along the fore and aft axis, which follows a sine curve; and coefficient C, from forces along the athwartships axis, which follows a cosine curve. Their sum is the deviation curve. In this example A is plus 1, B plus 4 and C minus 2.
Correction of coefficients
B on E/W, C on N/S, A on the lubber line
A : a displaced lubber line: loosen the compass (or RIMC detector unit) and turn itB : work out the reading you want, adjust on an E or W headingC : the same on a N or S heading; watch the signsThen a check swing on 8 or 12 headings: residuals go on the deviation card
N 3 6 E 12 15 S 21 24 W 30 33 085° on 090°M: reads 085° N 3 6 E 12 15 S 21 24 W 30 33 089° remove B: now 089° N 3 6 E 12 15 S 21 24 W 30 33 001° on 000°M: reads 001° N 3 6 E 12 15 S 21 24 W 30 33 359° remove C: now 359° N 3 6 E 12 15 S 21 24 W 30 33 359° A = +1 left on every heading N 3 6 E 12 15 S 21 24 W 30 33 000° turn the compass 1°: 000° ✓ corrector box B C B on an E or W heading B C on a N or S heading C A turn the compass (lubber line) A example: A +1, B +4, C −2
Chapter 33 · Aircraft Magnetism
12
E-books by eatpl.in · © 2026 · Do not copy or distribute
Coefficient A is a mechanical problem, a displaced lubber line, corrected by loosening the bolts holding the compass, or on a remote indicating compass the detector unit, and turning it until the correct heading shows. Coefficient B is corrected on an easterly or westerly heading, and coefficient C on a northerly or southerly heading: first work out the heading you want the compass to read, and apply the sign carefully. In the example, on 090 the compass reads 085 and is adjusted to 089; on 000 it reads 001 and is adjusted to 359; then the compass is turned one degree. A check swing on eight or twelve headings gives the residual deviations for the deviation card.
Worked example
From the swing to the corrections
Step Working Result Deviations N −1 · E +5 · S +3 · W −3 (and the four quadrantals) A mean of all eight readings +1 B (dev E − dev W) / 2 = (5 − (−3)) / 2 +4 C (dev N − dev S) / 2 = (−1 − 3) / 2 −2 Correct B on 090°M compass reads 085°; remove B so only A is left: make it read 089° dev +1 Correct C on 000°M compass reads 001°; remove C: make it read 359° dev +1 Correct A turn the compass (lubber line) 1°: it then reads the magnetic heading dev 0
Chapter 33 · Aircraft Magnetism
13
E-books by eatpl.in · © 2026 · Do not copy or distribute
A worked example. The swing gives minus 1 on north, plus 5 on east, plus 3 on south and minus 3 on west. A is the mean of all the readings, plus 1. B is half of east minus west, plus 4. C is half of north minus south, minus 2. On 090 magnetic the compass reads 085; removing B leaves only A, so adjust it to read 089. On 000 magnetic it reads 001; removing C, adjust it to read 359. Then turn the compass one degree to remove A. Remember: magnetic equals compass plus deviation.
Accuracy limits and the card
After correction: ±10° and ±1°
For (°M) Steer (°C) For (°M) Steer (°C) 000 001 180 177 045 043 225 225 090 085 270 273 135 130 315 318
A deviation card (the example, before correction): Steer = For − Deviation.
Direct reading compass ±10° -12 -8 -4 0 +4 +8 +12 Remote indicating compass ±1° -2 -1 0 +1 +2 residual deviation, ° residual deviation, ° (magnified scale) After correction the residual deviation on every heading must stay in the green band CS Ops-1 · the remote indicating compass limit is ten times tighter
Chapter 33 · Aircraft Magnetism
14
E-books by eatpl.in · © 2026 · Do not copy or distribute
European regulations, CS Ops-1, require the compasses after correction to be within plus or minus 10 degrees for a direct reading magnetic compass and plus or minus 1 degree for a remote indicating compass. The residual deviations are shown on a compass deviation card near the compass, often as For and Steer: the compass heading to steer for each magnetic heading, steer equals for minus deviation.
04
Latitude and swings
H, Z and tan dip.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part four: change of magnetic latitude and the occasions for swinging the compass.
Latitude in 3D
Fly north: H weakens, Z grows
Hard iron force is constant, but the directive force H falls towards the poles Hard iron max deviation ∝ 1 / H : same sign in both hemispheres VSI is magnetised by Z: max deviation ∝ Z / H = tan dip Both are least at the magnetic equator (VSI zero) and grow towards the poles
Chapter 33 · Aircraft Magnetism
16
E-books by eatpl.in · © 2026 · Do not copy or distribute
The hard iron deviating force stays constant with latitude, but the directive force H is greatest at the magnetic equator and zero at the poles. The smaller H, the greater the maximum deviation, so hard iron deviation is inversely proportional to H: least at the magnetic equator, increasing towards the poles, with the same sign in both hemispheres. Vertical soft iron is magnetised by Z, so its maximum deviation varies directly as Z and inversely as H: as Z over H, which is tan dip. It is zero at the magnetic equator and increases towards the poles.
Deviation and latitude
Both grow towards the magnetic poles
tan dip = Z / H Hard iron: max deviation ∝ 1 / H ; not affected by Z VSI: max deviation ∝ Z / H = tan dip ; zero at the equator A large change of magnetic latitude calls for a swing
0° 10° 20° 30° 40° 50° 60° 70° 80° 10° 20° 30° magnetic latitude max deviation (example aircraft) hard iron ∝ 1/H VSI ∝ tan dip magnetic equator hard 4.0° · VSI 0.0° 30° hard 4.6° · VSI 3.0° 60° hard 8.0° · VSI 8.9° 75° hard 15.7° · VSI 18.7°
Chapter 33 · Aircraft Magnetism
17
E-books by eatpl.in · © 2026 · Do not copy or distribute
Tan dip equals Z over H. Hard iron maximum deviation is inversely proportional to H and is not affected by Z. Vertical soft iron maximum deviation is proportional to Z over H, which is tan dip, so it is zero at the magnetic equator. Both grow towards the magnetic poles, slowly at first and then steeply. That is why a large change of magnetic latitude is one of the occasions for swinging the compass.
Occasions for swinging the compass
When to swing
Equipment Compass components installed or replaced
Accuracy in doubt
After a maintenance inspection, if the schedule requires
Aircraft changes Significant modification, repair or replacement involving magnetic material
Significant modification to radio/electrical systems
Unusual ferromagnetic payloads
Events Compass subjected to significant shock
Aircraft struck by lightning
Long-term storage standing on one heading
Moves A new theatre of operations involving a large change of magnetic latitude
Chapter 33 · Aircraft Magnetism
18
E-books by eatpl.in · © 2026 · Do not copy or distribute
Swing the compass when compass components are installed or replaced; whenever its accuracy is in doubt; after a maintenance inspection if the schedule requires it; after a significant modification, repair or replacement involving magnetic material; when carrying unusual ferromagnetic payloads; when the compass has had a significant shock; if the aircraft has been struck by lightning; after significant modification to radio or electrical systems; after a move to a new theatre with a large change of magnetic latitude; and if the aircraft has been in long-term storage standing on one heading.
Summary
Aircraft magnetism in six lines
Topic Remember Deviation Needle v magnetic meridian · Magnetic = Compass + Dev · West: compass best, East: compass least Swing On the swinging base v a landing compass: find, correct, record the residual Hard iron Permanent; P, Q, R fixed in the aircraft; max deviation ∝ 1/H; same sign both hemispheres VSI Induced by Z: none at the magnetic equator; max deviation ∝ Z/H = tan dip A, B, C A constant (lubber line), B = sine (correct on E/W), C = cosine (correct on N/S); check swing 8–12 points Limits Direct reading ±10°, remote indicating ±1° (CS Ops-1); swing after changes, shocks, lightning, big latitude moves
Chapter 33 · Aircraft Magnetism
19
E-books by eatpl.in · © 2026 · Do not copy or distribute
In summary: deviation is the angle between the needle and the magnetic meridian; magnetic equals compass plus deviation. The swing compares the compass with a landing compass on the swinging base to find, correct and record deviation. Hard iron is permanent and its deviation varies as one over H; vertical soft iron is induced by Z and its deviation varies as tan dip. A is constant, B a sine curve corrected on east or west, C a cosine curve corrected on north or south. Limits after correction are 10 degrees and 1 degree.
Questions 1–3
Questions: set 1
1. CS Ops-1 maximum permissible deviations after compensation: (a) one degree for a remote indicating compass, ten degrees for a direct reading compass (b) three for a direct reading, one for a remote indicating compass (c) ten for a remote indicating, one for a direct reading compass (d) one for a direct reading, eleven for a slaved compass
2. Compass swings should be carried out: (a) on the apron (b) only on the compass swinging base or site (c) at the holding point (d) on the active runway
3. Aircraft magnetism caused by vertical soft iron: (a) varies with magnetic heading but not with magnetic latitude (b) varies with magnetic latitude but not with heading (c) is not affected by magnetic latitude or heading (d) varies as the cosine of the compass heading
Chapter 33 · Aircraft Magnetism
20
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 4–6
Questions: set 2
4. Aircraft magnetism caused by hard iron: (a) is not usually influenced by the earth’s magnetic field (b) varies directly with magnetic latitude (c) varies indirectly with magnetic latitude (d) is maximum on east and west
5. The aim of a compass swing is: 1 to find deviation on the cardinal headings and calculate coefficients A, B and C; 2 to eliminate or reduce the coefficients found; 3 to record any residual deviation and prepare a compass correction card. (a) only 1 (b) 1 and 3 (c) 1, 2 and 3 (d) none
6. Aircraft magnetism caused by vertical soft iron: (a) varies with magnetic heading but not with magnetic latitude (b) varies with magnetic latitude but not with heading (c) is not affected by magnetic latitude or heading (d) varies as the cosine of the compass heading
Chapter 33 · Aircraft Magnetism
21
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 7–9
Questions: set 3
7. Aircraft magnetism caused by hard iron: (a) is not usually influenced by the earth’s magnetic field (b) varies directly with magnetic latitude (c) varies indirectly with magnetic latitude (d) is maximum on east and west
8. Deviation due to coefficient A is mainly caused by: (a) hard iron force along the longitudinal axis (b) hard and soft iron forces along the lateral axis (c) vertical soft iron forces (d) a misaligned lubber line
9. The aim of a compass swing is: 1 to find deviation on the cardinal headings and calculate A, B and C; 2 to eliminate or reduce the coefficients; 3 to record any residual deviation and prepare a compass correction card. (a) only 1 (b) 1 and 3 (c) 1, 2 and 3 (d) none
Chapter 33 · Aircraft Magnetism
22
E-books by eatpl.in · © 2026 · Do not copy or distribute
Answers
Answers from the chapter text
Q Answer Why 1 (a) Remote indicating ±1°, direct reading ±10° 2 (b) Only on the compass swinging base or site 3 (b) VSI is magnetised by Z: it varies with latitude, not with heading 4 (a) Hard iron is permanent: not induced by the earth’s field 5 (c) Find, correct and record: all three 6 (b) As Q3 7 (a) As Q4 8 (d) A misaligned lubber line 9 (c) As Q5
Q3/6, Q4/7 and Q5/9 are repeated pairs: each pair has the same answer. These answers follow the chapter text.
Chapter 33 · Aircraft Magnetism
23
E-books by eatpl.in · © 2026 · Do not copy or distribute
Answers from the chapter text. Questions 3 and 6, 4 and 7, and 5 and 9 are identical pairs with the same answers. The answers: 1 a, 2 b, 3 b, 4 a, 5 c, 6 b, 7 a, 8 d, 9 c.
Try it yourself
Compass Swing Lab
Swing a 3D aircraft on a compass base against a landing compass Set hard iron, vertical soft iron and lubber-line errors Find A, B and C, correct them on the right headings, check swing Move to another magnetic latitude and watch the deviation change The chapter questions and worked swing problems Open the Compass Swing Lab →
Chapter 33 · Aircraft Magnetism
24
E-books by eatpl.in · © 2026 · Do not copy or distribute
The Compass Swing Lab lets you swing a 3D aircraft on a compass base against a landing compass, set hard iron, vertical soft iron and lubber line errors, find coefficients A, B and C, correct them on the right headings, do a check swing for the deviation card, and see how deviation changes with magnetic latitude.
eatpl.in · General Navigation · Chapter 33
Compass Swing Lab
An aircraft with its own magnetism on a compass swinging base. Swing it, find A, B and C, correct them on the right headings, then check swing. A teaching model: forces are in units of H at the magnetic equator.
Swing
Practice
The nine questions (answers from the chapter text), then swing problems. Set up puts the lab in the matching state.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.