General Navigation · Chapter 35
Inertial Reference System
Ring laser gyros strapped to the airframe: the stable platform now lives in the computer.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter 35 covers the inertial reference system: the inertial reference unit and its outputs and users, the laser gyro and the Sagnac effect, its construction and operation, its limitations including lock-in and the dither motor, strap-down principles, alignment and the advantages over the gimballed INS.
Chapter roadmap
What this chapter covers
IRU 01
Strap-down IRS No gimbals: the IRU, its outputs and its users.
02
The laser gyro Sagnac effect, construction, fringes.
03
Limits Drift, path length, lock-in and dither.
04
Align and advantages True north, latitude check, levelling.
Chapter 35 · Inertial Reference System
02
E-books by eatpl.in · © 2026 · Do not copy or distribute
Four parts: strap-down principles with the inertial reference unit, its outputs and its users; the laser gyro, its Sagnac principle, construction and fringe pattern; its limitations, drift, path length, lock-in and the dither motor; and finally alignment and the advantages. Then the questions and the IRS Lab.
01
Strap-down
The platform moves into the computer.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part one: strap-down principles and the inertial reference unit.
Introduction
A technological revolution
The laser gyro A solid-state , high-precision angular rate sensor .
Ideal for a highly reliable strap-down system.
No moving parts No gimbals , bearings , torque motors or other moving parts.
System operation changes considerably from the INS.
Inertial navigation Finding the vehicle’s position without external references .
Strap-down goes further: no mechanically stabilised platform.
Microprocessors IRU Laser gyros plus fast processors keep a stable platform mathematically , not mechanically.
Chapter 35 · Inertial Reference System
04
E-books by eatpl.in · © 2026 · Do not copy or distribute
The laser gyro has caused a technological revolution in inertial reference and navigation systems. It is a solid-state, high-precision angular rate sensor, ideally suited to a highly reliable strap-down configuration, eliminating gimbals, bearings, torque motors and other moving parts. Inertial navigation means finding a vehicle’s location without external references; strap-down inertial navigation does it without a mechanically stabilised platform, because laser gyros and powerful, high-speed microprocessors maintain the platform mathematically.
Strap-down in 3D
Sensors fixed to the aircraft
Three laser gyros and three accelerometers fixed to the airframe They turn with the aircraft through every manoeuvre The computer integrates the rates: it always knows the attitude A level, north-referenced platform is held mathematically
Chapter 35 · Inertial Reference System
05
E-books by eatpl.in · © 2026 · Do not copy or distribute
In the IRS the three laser gyros and the accelerometers are attached directly to the aircraft structure, strapped down, and turn with it. The gyros measure the rates of turn about all three axes; high-speed microprocessors integrate them so that the computer always knows the aircraft’s attitude and heading, and can resolve the accelerations into a level, north-referenced frame. That frame is the stable platform, but it exists only in the computer. The result is greatly improved accuracy and reliability.
Platform v strap-down
Same physics, no gimbals
INS: gyros and accelerometers on a gimballed platform , kept level at the correct latitude IRS: laser gyros and accelerometers attached directly to the chassis Microprocessors give a stable platform mathematically Result: greatly improved accuracy and reliability
INS: gimballed platform IRS: strap-down the gimbals turn so the platform stays level green line: the level, computed mathematically Sensors on a gimballed stable platform fixed to the aircraft structure Gyros spinning rate-integrating gyros ring laser gyros (rate sensors) Moving parts gimbals, bearings, torque motors none: solid state Level and north held mechanically held mathematically Start-up minutes of warm-up about 1 second for the rate sensor
Chapter 35 · Inertial Reference System
06
E-books by eatpl.in · © 2026 · Do not copy or distribute
The gimballed INS needs three rate-integrating gyros and accelerometers on a platform which must first be made horizontal at the correct latitude, and the gimbals then keep it level mechanically. The IRS attaches the three laser gyros, or rate sensors, and the accelerometers directly to the aircraft chassis. High-speed microprocessors then achieve a stable platform mathematically rather than mechanically, which gives greatly improved accuracy and reliability.
The inertial reference unit
The IRU: heart of the IRS
Output Data Primary attitude pitch and roll Heading true and magnetic Accelerations lateral, longitudinal, normal Angular rates pitch, roll, yaw Inertial velocity N/S, E/W, groundspeed, track angle, vertical rate Position latitude, longitude, inertial altitude Wind data wind speed, wind angle, drift angle Calculated data flight path angle and acceleration · along- and across-track acceleration · inertial pitch and roll rate · vertical acceleration · potential vertical speed
Chapter 35 · Inertial Reference System
07
E-books by eatpl.in · © 2026 · Do not copy or distribute
The inertial reference unit is the heart of the inertial reference system, providing all the inertial reference outputs the avionics need: primary attitude, pitch and roll; true and magnetic heading; lateral, longitudinal and normal accelerations; pitch, roll and yaw rates; inertial velocity, north-south, east-west, groundspeed, track angle and vertical rate; position, latitude, longitude and inertial altitude; wind speed, wind angle and drift; and calculated data such as flight path angle and acceleration, along- and across-track acceleration, inertial pitch and roll rate, vertical acceleration and potential vertical speed.
Inputs and users
What goes in, and who uses it
Primary sources: its own 3 laser gyros and 3 accelerometers Initial position : present position is worked out from itBaro altitude : stabilises vertical velocity and inertial altitudeTAS : lets it compute wind speed and direction
Inputs → IRU → users of inertial information Initial position present position calculated from it Barometric altitude stabilises vertical navigation True airspeed lets the IRU compute the wind IRU 3 laser gyros 3 accelerometers Flight management computer Flight control computer Thrust management computer Stability augmentation Weather radar Anti-skid / autobrake ADI HSI VSI RDMI Flight data recorder Only three external inputs everything else comes from its own sensors
Chapter 35 · Inertial Reference System
08
E-books by eatpl.in · © 2026 · Do not copy or distribute
The IRU’s primary sources of information are its own internal sensors, three laser gyros and three accelerometers. The only other inputs are initial position, because present position is calculated from the distance and direction travelled from it; barometric altitude, which stabilises the vertical navigation and so the vertical velocity and inertial altitude outputs; and true airspeed, which allows the IRU to calculate wind speed and direction. Its information is used by the flight management, flight control and thrust management computers, the stability augmentation system, weather radar, anti-skid and autobrake, the ADI, HSI, VSI, RDMI and the flight data recorder.
02
The laser gyro
Two beams, opposite ways round.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: the laser gyro.
The ring laser gyro in 3D
Rotation shows up as a frequency difference
Two beams go round a triangle in opposite directions At rest: same path, same frequency, fringes still Rotating: one path longer, the other shorter (Sagnac effect ) Fringes move across the photocell: speed = rate , direction = sense
Chapter 35 · Inertial Reference System
10
E-books by eatpl.in · © 2026 · Do not copy or distribute
The laser gyro uses the characteristics of light to measure motion, through the Sagnac effect. Two laser beams travel round a triangular path in opposite directions. To keep lasing, the path length must hold a whole number of wavelengths. When the gyro rotates, one beam has a longer path and its frequency falls, the other a shorter path and its frequency rises. The frequency difference is easily and accurately measured: it moves an interference fringe pattern across a photocell, faster for a faster rotation, in a direction that shows which way the gyro is turning.
The Sagnac effect
Path length, wavelength, frequency
Lasing needs a whole number of wavelengths in the path Shorter path: light “compressed”, frequency rises Longer path: frequency falls The frequency difference is proportional to the rate of turn
Light round a turning ring start / detector rotation beam 1 → ← beam 2 at rest: both beams take the same time with the turn: beam 1 has further to go against it: beam 2 arrives sooner Whole number of wavelengths in the path equal paths → equal frequencies Δf = 0: fringes stand still beam 1: longer path → lower frequency beam 2: shorter path → higher frequency beam 1 beam 2 Δf = 4AΩ / (λL) A area, L path length, λ wavelength, Ω rate Δf ∝ Ω: count the fringes to measure the turn
Chapter 35 · Inertial Reference System
11
E-books by eatpl.in · © 2026 · Do not copy or distribute
The beams travel at the same speed, the speed of light. If the device is not turning, both take the same time round. When it turns, one beam takes longer to complete its path and the other a measurably shorter time. Because the path must hold a whole number of wavelengths, a shorter effective path compresses the light and raises its frequency, a longer one lowers it. The frequency difference is proportional to the rate of turn; for a ring of area A, path length L and wavelength lambda it is 4 A omega over lambda L.
Construction and operation
Glass, gas, mirrors and a prism
Two beams sent round a triangular path in opposite directions Unwanted frequencies are absorbed by the mirrors and coatings One mirror keeps the path accurately aligned; one lets light out A prism folds one beam onto the other: interference fringes
Inside a ring laser gyro + + − 1 1 Temperature-stable glass block tunnels drilled parallel to its edges 1 Temperature-stable glass block tunnels drilled parallel to its edges 2 2 Helium-neon gas, high voltage anodes (+), cathode (−): pinkish-orange 2 Helium-neon gas, high voltage anodes (+), cathode (−): pinkish-orange 3 3 Three mirrors, not identical one adjusts the path length (piezo) 3 Three mirrors, not identical one adjusts the path length (piezo) 4 4 Partly transparent mirror + prism beams interfere: fringes on photocells 4 Partly transparent mirror + prism beams interfere: fringes on photocells 5 5 Piezo-electric dither motor vibrates the ring to break lock-in 5 Piezo-electric dither motor vibrates the ring to break lock-in
Chapter 35 · Inertial Reference System
12
E-books by eatpl.in · © 2026 · Do not copy or distribute
The laser gyro has three mirrors giving a triangular path. The beams travel through small tunnels drilled parallel to the edges of a triangular block of temperature-stable glass, with mirrors in each corner. Lasing is achieved by running a high voltage through helium-neon gas between the anodes and the cathode, producing light in the pinkish-orange part of the spectrum. Light of unwanted frequencies is absorbed by the mirrors and their coatings. The three mirrors are not identical: one makes micro-adjustments to keep the path length right, another is partly transparent so the light reaches the photocells; with it, a prism turns one beam round to meet and interfere with the other, generating a fringe pattern whose speed and direction of motion give the rate and sense of rotation.
03
Limitations
Drift, path length and lock-in.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: limitations and accuracy.
Lock-in and dither
The most significant potential problem
Lock-in (laser lock) at very low rotation ratesBack-scatter between the beams makes them synchroniseOutput drops to zero, and errors are introduced Cure: a piezo-electric dither motor vibrates the ring through the lock-in region; its motion is removed from the output
Output v input rotation rate input rate output lock-in band ideal very slow turn: back-scatter locks the beams together output frequency drops to zero: the turn is missed dither swings the ring through the band quickly the dither is taken out: the small real turn is left Piezo-electric dither motor dither OFF dither ON: vibrates about the input axis Why it matters Earth rate is only 15°/h = 0.004°/s, deep inside the lock-in band: without dither the IRS could never align
Chapter 35 · Inertial Reference System
14
E-books by eatpl.in · © 2026 · Do not copy or distribute
The most significant potential problem is lock-in, also called laser lock, which occurs at very low rotation rates. Back-scattering between the two beams causes them to synchronise, so the output frequency drops to zero and the rotation is not indicated correctly. It is overcome by a piezo-electric dither motor, mounted so that it vibrates the laser ring about its input axis through the lock-in region, unlocking the beams so that the optical sensor can detect the smaller movement of the fringe pattern. The dither motion is decoupled from the gyro’s output.
Limitations and accuracy
Drift, path length and lock-in
Drift The principal error, as with the INS: random drift .
Laser gyro: noise , almost entirely from imperfect mirrors and coatings (not bearings or mass imbalance).
Path length Accuracy depends directly on the optical path length .
A small % increase in length gives a substantial increase in accuracy.
Lock-in At very low rates the beams lock together by back-scatter.
Broken by the dither motor ; dither removed from the output.
Chapter 35 · Inertial Reference System
15
E-books by eatpl.in · © 2026 · Do not copy or distribute
The principal source of error, as with the conventional platform, is random drift. In a conventional gyro it comes from bearing imperfections and mass imbalance; in the laser gyro it is noise, almost entirely from imperfections in the mirrors and their coatings. Accuracy depends directly on the length of the optical path: a small percentage increase in length gives a substantial increase in accuracy. And lock-in at very low rates is broken by the dither motor.
04
Align and advantages
True north, latitude, levelling.
E-books by eatpl.in · © 2026 · Do not copy or distribute
Part four: strap-down processing, alignment and advantages.
Strap-down processing
The same corrections as the INS, done in software
Integration As in the INS: acceleration → velocity → distance .
Gravity The processor subtracts local gravity from any vertical acceleration.
Earth rate Compensated at 15.04°/h , as with the gyro INS.
Transport Schuler tuning again: an 84.4 min error cycle.
Calibration Automatic calibration by the computer improves accuracy.
Chapter 35 · Inertial Reference System
17
E-books by eatpl.in · © 2026 · Do not copy or distribute
Strap-down processing uses the same principles as the INS. Integration is as in the older INS. The microprocessor subtracts the effect of local gravity from any vertical acceleration. Earth rotation is compensated at 15.04 degrees per hour, as with a gyro INS. Transport rate needs Schuler tuning again, with the 84.4 minute error cycle of the older INS. And calibration is completed automatically by the computer to enhance the overall accuracy.
Alignment in 3D
Finding true north and latitude from earth rate
Stationary on the ground: the only rotation sensed is the Earth’s Its horizontal component points to true north Vertical ÷ horizontal = tan latitude: latitude found Compared with the latitude entered by the operator
Chapter 35 · Inertial Reference System
18
E-books by eatpl.in · © 2026 · Do not copy or distribute
Like the INS, the IRS has to find true north to align. It does this while the aircraft is stationary on the ground, when the only rate it senses is that of the Earth. The horizontal component of earth rate lies along the meridian, giving true north. The ratio of the vertical and horizontal components gives the latitude, which the computer compares with the latitude entered by the operator during initialisation.
Alignment
Enter position, find north, check latitude, level
Operator enters initial latitude and longitude (present position) True north found while stationary : only earth rate is sensed Latitude found is compared with that entered Then a full mathematical levelling Do not move the aircraft during the process
IRS alignment, step by step OFF ALIGN NAV ATT mode selector ALIGN ALIGN 1 Enter present position latitude and longitude, manually 1 Enter present position latitude and longitude, manually 2 Gyros sense earth rate only the aircraft is stationary 2 Gyros sense earth rate only the aircraft is stationary 3 True north found from the horizontal component 3 True north found from the horizontal component 4 Latitude check found v entered; position at landing remembered 4 Latitude check found v entered; position at landing remembered 5 Mathematical levelling a full levelling, done in the computer 5 Mathematical levelling a full levelling, done in the computer 6 Aligned → NAV now the aircraft may move 6 Aligned → NAV now the aircraft may move Earth rate at latitude λ horizontal (north) Ω 15.04°/h Ω cos λ Ω sin λ λ tan λ = vertical ÷ horizontal ENTERED FOUND BY THE IRS N51 28.5 N51 28.4 Memory remembers its position at landing and flags a wrong lat or long entered at start-up THE AIRCRAFT MUST NOT BE MOVED DURING THE ALIGNMENT
Chapter 35 · Inertial Reference System
19
E-books by eatpl.in · © 2026 · Do not copy or distribute
Initial latitude and longitude must be entered manually as present position. With the aircraft stationary the laser gyros sense only earth rotation, and true north is found. After assessing the rotation vectors it is experiencing, the computer compares the latitude it finds with the latitude entered. The IRS also remembers its position at landing and will warn the crew of any error in the initial latitude or longitude at start-up. After confirming the latitude it completes a full mathematical levelling. The aircraft must not be moved during the process.
Advantages
Why the airlines went strap-down
Activation Almost no spin-up time: about 1 second for the rate sensor.
Manoeuvring Insensitive to g , attitude, rolling and pitching.
Construction Mechanically simple and highly reliable .
Range Wide dynamic range of rates sensed.
Drift Very small drift: the biggest errors are the operator’s .
Chapter 35 · Inertial Reference System
20
E-books by eatpl.in · © 2026 · Do not copy or distribute
The advantages: almost no spin-up time, about one second’s activation for the rate sensor; insensitivity to g, attitude, rolling and pitching manoeuvres; mechanically simple and highly reliable construction; a wide dynamic range; and very small drift rates, so that the greatest errors are those induced by the operator.
Summary
The IRS in six lines
Topic Remember Strap-down 3 laser gyros + 3 accelerometers fixed to the airframe; stable platform held mathematically IRU Attitude, heading (T and M), accelerations, rates, velocity, position, wind; inputs: initial position, baro altitude (vertical), TAS (wind) Laser gyro Sagnac: two counter-rotating He-Ne beams, 3 mirrors; rotation → frequency difference → moving fringes (speed = rate, direction = sense) Limits Drift = noise from mirror imperfections · longer path, more accurate · lock-in at low rates → piezo dither motor, removed from output Processing Integration as INS · gravity subtracted · earth rate 15.04°/h · Schuler tuning 84.4 min · automatic calibration Alignment Stationary: earth rate → true north; latitude found v entered; landing position memory; mathematical levelling; don’t move
Chapter 35 · Inertial Reference System
21
E-books by eatpl.in · © 2026 · Do not copy or distribute
In summary: strap-down laser gyros and accelerometers, with the platform held mathematically; the IRU’s outputs and its three external inputs; the Sagnac principle and fringe detection; drift, path length and lock-in cured by dither; the INS corrections done in software; and alignment by sensing earth rate while stationary, with a latitude check and a mathematical levelling.
Questions 1–4
Question 1, then practice
1. Dither is used in a laser gyro in order to: (a) enhance the accuracy at all rotation rates (b) increase the maximum rate that can be sensed (c) stabilise the laser frequencies at peak power (d) break the frequency lock which would prevent small rotation rates from being sensed
2. A ring laser gyro senses rotation by measuring: (a) the precession of a spinning rotor (b) the frequency difference between two counter-rotating beams (c) the change in laser power (d) the time for one beam to go round
3. Lock-in occurs: (a) at very high rotation rates (b) when the dither motor fails at any rate (c) at very low rotation rates, from back-scatter between the beams (d) when the path length is too long
4. Apart from its own sensors, the IRU needs: (a) initial position, baro altitude and TAS (b) magnetic heading and TAS (c) initial position only (d) DME and VOR
Chapter 35 · Inertial Reference System
22
E-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 1 to 7 are eatpl.in practice questions on the chapter.
Questions 5–7
More practice
5. The barometric altitude input to the IRU: (a) gives the inertial altitude directly (b) stabilises the vertical navigation, vertical velocity and inertial altitude (c) is used to compute the wind (d) corrects the latitude
6. The main source of random drift in a laser gyro is: (a) bearing friction (b) mass imbalance (c) noise from imperfections in the mirrors and coatings (d) Schuler oscillation
7. During IRS alignment: (a) the aircraft may taxi once position is entered (b) true north is found from earth rate while stationary, and the latitude found is compared with that entered (c) magnetic north is found from the flux valve (d) only longitude needs entering
Chapter 35 · Inertial Reference System
23
E-books by eatpl.in · © 2026 · Do not copy or distribute
Practice questions 5 to 7.
Answers
Answers with the reasoning
Q Answer Why 1 (d) dither breaks the frequency lock so that small rates can be sensed 2 (b) Sagnac effect: rotation gives a frequency difference between the two beams 3 (c) At very low rates back-scatter synchronises the beams 4 (a) Initial position, barometric altitude and TAS 5 (b) Baro altitude stabilises vertical navigation; TAS gives the wind 6 (c) Noise from imperfect mirrors and coatings 7 (b) Stationary: earth rate → true north; latitude check; mathematical levelling; don’t move
Chapter 35 · Inertial Reference System
24
E-books by eatpl.in · © 2026 · Do not copy or distribute
Answers with the reasoning. Question 1 is (d): dither breaks the frequency lock which would prevent small rates being sensed.
Turn a 3D ring laser gyro and watch the fringes move Change the path length; find Δf for any rate Switch the dither off and find the lock-in band Align an IRS: enter position, watch it find north and check latitude The questions, with the lab set up for each Open the IRS Lab →
Chapter 35 · Inertial Reference System
25
E-books by eatpl.in · © 2026 · Do not copy or distribute
The IRS Lab lets you turn a 3D ring laser gyro and watch the fringe pattern, change the path length and rate, switch the dither off to find the lock-in band, align an IRS with a latitude check, and practise the questions.
eatpl.in · General Navigation · Chapter 35
IRS Lab
Turn a ring laser gyro and watch the fringes, find the lock-in band, then align an IRS. A teaching model: the lock-in rate and tolerances are typical illustrative values.
Laser gyro
Alignment
Practice
Input
Zero the fringe counter
MODE OFF ALIGN NAV ATT
ALIGN FAULT
LATITUDE FOUND BY THE IRS
The first question, then eatpl.in practice questions. Set up puts the lab in the matching state.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.