IFR Training · Chapter 4
Bearings, Radials and Tracking The language of radio navigation: QDM and QDR, relative bearing, radials and courses, interception angles and tracking with drift.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every instrument procedure, whether it uses a VOR, an NDB or an ILS, is built from the same few ideas: a bearing to a station, a bearing from it, a track you want to fly, and an angle at which you join that track. Get these ideas clear in your head now, and the equipment specific lessons that follow become simple. Get them muddled, and no instrument will save you from disorientation.
Roadmap
Where is the station, and where do I want to be? Bearings QDM is the magnetic bearing to the station; QDR is the bearing from it.
Radials and courses A radial is a QDR from a VOR. Inbound and outbound courses are the tracks you want.
Interception Join a course at a chosen interception angle , and lead the turn on to it.
Tracking Hold the course with a wind correction angle , found by bracketing.
Chapter 4 · Bearings, Radials and Tracking
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
We start with bearings: to the station and from the station. Then radials and courses, which describe the track you want to fly. Then interception, which is how you get on to that track. And finally tracking, which is how you stay on it when the wind is trying to push you off.
Bearings
QDM points to the station, QDR points away from it QDM : the magnetic bearing from the aircraft to the stationFly the QDM as a heading in still air and you arrive overhead QDR : the magnetic bearing from the station to the aircraftQDM and QDR always differ by 180° They depend only on where you are , never on which way you are pointing As you fly past a station, the bearing changes; the closer you are, the faster Heading 075° NDB N
Chapter 4 · Bearings, Radials and Tracking
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Start with two Q codes that you will use for the rest of your flying life. The Q D M is the magnetic bearing from the aircraft to the station. If you flew that bearing as a heading in still air, you would arrive overhead. The Q D R is the magnetic bearing from the station to the aircraft. The two always differ by one hundred and eighty degrees. Notice that both depend only on where you are, never on which way the nose is pointing. Watch the aircraft fly past the beacon on a steady heading. The Q D M changes all the time, slowly at first and quickly when the aircraft is close, and the needle swings from ahead, past the wing tip, towards the tail.
Relative bearing
Heading plus relative bearing gives the QDM Relative bearing : the angle from the aircraft's nose, clockwise , to the stationIt is what a fixed-card ADF shows QDM = magnetic heading + relative bearing Heading 040°, relative bearing 060° → QDM 100° If the sum is more than 360, subtract 360: heading 300° + RB 100° = 400 → QDM 040° Relative bearing changes when you turn; the QDM does not N 3 6 E 12 15 S 21 24 W 30 33 Magnetic heading 040° 0 3 6 9 12 15 18 21 24 27 30 33 Relative bearing 060° N 3 6 E 12 15 S 21 24 W 30 33 QDM 100° on an RMI N 3 6 E 12 15 S 21 24 W 30 33 Heading 300° + RB 100° = QDM 040°
Chapter 4 · Bearings, Radials and Tracking
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The third quantity is the relative bearing. It is the angle measured clockwise from the nose of the aircraft round to the station, and it is what a simple fixed card A D F displays. To turn a relative bearing into a bearing you can use on a chart, add your heading. Magnetic heading plus relative bearing equals the Q D M. For example, heading zero four zero with a relative bearing of zero six zero gives a Q D M of one hundred. If the total comes to more than three hundred and sixty, subtract three hundred and sixty. One thing to remember: when you turn, the relative bearing changes by the amount of the turn, but the Q D M stays the same, because you have not moved.
Radials and courses
A radial always points away from the VOR A radial is a magnetic bearing from a VOR: a QDR There are 360 of them, like the spokes of a wheel Flying outbound on radial 270°, your track is 270° Flying inbound on radial 090°, your track is the reciprocal: 270° Inbound course : the track to the station. Outbound course : the track away from itPosition reports use the radial: "on the 090 radial, 20 miles" Radial 360° Radial 090° Radial 180° Radial 270° Inbound on radial 090° · track 270° Outbound on radial 270° VOR N
Chapter 4 · Bearings, Radials and Tracking
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
With a V O R we talk about radials. A radial is simply a magnetic bearing from the station, a Q D R, and there are three hundred and sixty of them, like the spokes of a wheel. The important thing is that a radial always points away from the station. If you fly outbound on the two seven zero radial, your track is two seven zero. But if you fly inbound on the zero nine zero radial, your track is the reciprocal, two seven zero. The track you want to fly towards a station is called the inbound course, and the track away from it is the outbound course. Watch the radial readout change from zero nine zero to two seven zero as the aircraft passes overhead, while the course stays the same.
Staying oriented
How the bearing changes tells you where the station is If you hold a heading that is… the QDM will… and the needle on an RMI… Equal to the QDMstay constant (no wind) stays on the nose Less than the QDM (station to the right of the nose)increase moves clockwise, down the right side Greater than the QDM (station to the left of the nose)decrease moves anticlockwise, down the left side At right angles to the QDM change fastest passes the wing tip
"The head of the needle always falls." If it does not behave as you expect, stop and re-orient before you turn.
Chapter 4 · Bearings, Radials and Tracking
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a small table that prevents a great deal of disorientation. If the heading you hold is equal to the Q D M, the bearing stays constant and the needle stays on the nose. If your heading is less than the Q D M, the station is to the right of the nose, and as you fly on the Q D M increases: the needle moves clockwise down the right hand side of the instrument. If your heading is greater than the Q D M, the station is on your left, and the Q D M decreases. In other words, the head of the needle always falls towards the tail. If the needle is not doing what you expect, do not turn. Stop, and work out where you really are.
Interception
The interception angle is measured between heading and course Interception angle : the angle between your heading and the course you wantInbound, about 30° to 60° is normal; outbound, about 45° Never more than 90° : beyond that you fly away from the station A larger angle gets you there sooner but needs an earlier, bigger turn Close to the station the bearing changes quickly: use a smaller angle Lead the turn on to the course so that you roll out on it, not through itDesired: inbound 270° Intercept heading 210° Inbound course 270° VOR N
Chapter 4 · Bearings, Radials and Tracking
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
To get on to a course you fly a heading that cuts across it. The angle between that heading and the course is the interception angle. For an inbound course, thirty to sixty degrees is normal. For an outbound course, about forty five degrees. It should never be more than ninety, because beyond that you are flying away from where you want to go. A larger angle gets you to the course sooner, but you will need to start a bigger turn earlier. Close to the station, the bearing changes quickly, so use a smaller angle. And always lead the turn, so that you roll out on the course instead of flying through it. Here the aircraft intercepts the two seven zero inbound course at sixty degrees.
Tracking
Hold the course with a wind correction angle With a crosswind, heading and track are different: the difference is the wind correction angle On track with the correction applied, the course needle stays centred while the nose points into wind Bracketing : drifted off? Turn towards the course by double the deviationWhen back on course, take off half the correction and hold it Still drifting? Adjust by a few degrees and try again The bearing staying constant is the proof that you are tracking Heading 280° · track 270° Still 10° into wind VOR N
Chapter 4 · Bearings, Radials and Tracking
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Staying on a course is called tracking, and in a crosswind it means flying with the nose pointed slightly into wind. The angle between your heading and your track is the wind correction angle. You find it by bracketing. Suppose you hold the course as a heading and find you have drifted five degrees off. Turn towards the course by double the deviation, ten degrees, and wait until you are back on. Then take off half the correction, leaving five degrees into wind, and see if it holds. If you still drift, adjust by a few degrees and try again. You know you have it right when the bearing stays constant. Notice that the same correction, on the same side, works both inbound and outbound.
Mental arithmetic
Three rules that turn angles into distance and time One in sixty At 60 NM , 1° off track is 1 NM off track. At 30 NM, 1° is ½ NM; at 10 NM it is only about 1,000 ft.
Time to the station Turn to put the station on the wing tip and time a bearing change. Minutes to station = seconds flown ÷ degrees of change .
Distance to the station Distance = TAS × minutes ÷ 60 . Example: 10° takes 120 s → 12 minutes; at 120 kt that is 24 NM.
These are estimates in still air. They are for orientation, not for descending below a safe altitude.
Chapter 4 · Bearings, Radials and Tracking
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three pieces of mental arithmetic complete the toolkit. First, the one in sixty rule: at sixty nautical miles from a station, one degree off track is one nautical mile off track. At thirty miles one degree is half a mile, and at ten miles it is only about a thousand feet. Second, time to the station. Put the station on your wing tip, hold the heading, and time how long the bearing takes to change by a known number of degrees. The time to the station in minutes is the seconds flown divided by the degrees of change. Third, the distance is your true airspeed times those minutes, divided by sixty. So if ten degrees takes one hundred and twenty seconds, you are twelve minutes out, which at one hundred and twenty knots is twenty four miles.
Summary
What to carry into the cockpit and the exam QDM / QDR Bearing to and from the station; 180° apart; independent of heading.
Relative bearing Clockwise from the nose. QDM = heading + relative bearing.
Radial A bearing FROM a VOR. Inbound on radial 090° means tracking 270°.
Needle The head always falls. Heading less than QDM: the QDM increases.
Interception 30° to 60° inbound, 45° outbound, never over 90°. Lead the turn.
Tracking Bracket: double the deviation to regain, then hold half.
Chapter 4 · Bearings, Radials and Tracking
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
In summary. The Q D M is the bearing to the station and the Q D R the bearing from it. Heading plus relative bearing gives the Q D M. A radial is a bearing from a V O R, so inbound on the zero nine zero radial you are tracking two seven zero. The head of the needle always falls. Intercept at thirty to sixty degrees inbound and forty five outbound, and lead the turn. And track by bracketing: double the deviation to get back, then hold half of it as your wind correction.