IFR Training · Chapter 9
Holding Patterns The racetrack that keeps you safe while you wait: the pattern, the three sector entries, timing, wind corrections and speeds.
Holding radial 270° Inbound leg Fix end turn Outbound leg Outbound end turn Holding fix N © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to holding. A hold is simply a racetrack flown around a fix, used whenever air traffic control needs you to wait: for traffic ahead, for weather to improve, or to lose height before an approach. In this lesson we fly the standard pattern, learn the three ways to enter it and how to pick the right one in seconds, and then correct the pattern for wind so that every inbound leg takes exactly one minute.
Roadmap
Holding: one racetrack, three ways in The pattern Inbound leg, two rate one turns and an outbound leg. Standard turns are to the right .
Entries Direct, parallel, offset : chosen from the heading on which you reach the fix.
Timing and wind Adjust the outbound time so the inbound leg lasts one minute ; triple the drift outbound.
Speeds and clearances Maximum holding speeds by level, and what EAT means for your fuel.
Chapter 9 · Holding Patterns
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan. First the pattern itself and its names. Then the three sector entries: direct, parallel and offset. After that, timing and wind, where most marks are lost. And finally holding speeds and the clearance you can expect from the controller.
The pattern
A standard hold is a right-hand racetrack The hold is anchored on a holding fix : a VOR, an NDB, a DME distance or a waypoint You fly the inbound leg towards the fix along the published holding track Over the fix, turn 180° at rate one on to the outbound leg Outbound runs parallel to the inbound track; then another rate one turn brings you back Standard = right turns . Left turns only when the chart or ATC says soOne complete circuit takes about four minutes in still air Holding radial 270° Inbound leg Fix end turn Outbound leg Outbound end turn Holding fix N
Chapter 9 · Holding Patterns
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A standard holding pattern is a racetrack with right turns. It is anchored on a holding fix, which may be a VOR, an NDB, a D M E distance or a waypoint. You fly the inbound leg towards the fix along the published track. Over the fix you make a rate one turn through one hundred and eighty degrees on to the outbound leg, fly parallel to the inbound track, then make another rate one turn to roll out inbound again. Each turn takes a minute and each straight leg takes a minute, so in still air one circuit takes four minutes. Turns are to the right unless the chart or the controller says otherwise. Watch the aircraft fly it, and watch the course bar centre on the inbound leg.
The language of the hold
Six terms the controller and the chart will use Holding fix The point the pattern is built on. Every circuit ends by crossing it on the inbound track.
Inbound track The published track to the fix. It is the only leg guided by a radial or bearing.
Holding side The side of the inbound track on which the pattern is flown. The other is the non-holding side .
Abeam The point on the outbound leg directly opposite the fix. Outbound timing starts here .
Outbound end The turn furthest from the fix, where you turn back to intercept the inbound track.
Protected area Obstacle clearance is assured only inside it, so keep to the speed, timing and side.
Chapter 9 · Holding Patterns
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six terms come up again and again. The holding fix is the point the pattern is built on. The inbound track is the published track to the fix, and it is the only leg with track guidance. The holding side is the side of that track where the pattern lies; the other side is the non holding side. Abeam is the point on the outbound leg directly opposite the fix, and it is where outbound timing starts. The outbound end is the far turn. And the protected area is the airspace surveyed for obstacles: you are only safe inside it, which is why speed, timing and direction of turn all matter.
Entry sectors
The heading at the fix decides the entry Draw a line through the fix at 70° to the inbound track , across the holding side It splits the compass into three sectors as seen from the fix Sector 1 · Parallel : 110° wide. You arrive from beyond the fix on the holding side Sector 2 · Offset (teardrop) : 70° wide. You arrive from beyond the fix on the non-holding side Sector 3 · Direct : the remaining 180°, which includes the inbound track itselfYou get 5° of tolerance either side of each boundary The sector is fixed by your heading as you reach the fix, not by your track over the ground.
70° line Fix N
Chapter 9 · Holding Patterns
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
How you join depends on the heading on which you arrive at the fix. Imagine a line drawn through the fix at seventy degrees to the inbound track, cutting across the holding side. Together with the inbound track it divides the sky into three sectors. Arrive from sector one, a one hundred and ten degree slice beyond the fix on the holding side, and you fly a parallel entry. Arrive from sector two, the seventy degree slice beyond the fix on the non holding side, and you fly an offset entry, often called a teardrop. Arrive from sector three, the remaining half of the compass, and you fly a direct entry. There is a tolerance of five degrees on each boundary, so near a line you may choose either entry.
Sector 3
Direct entry: cross the fix and turn outbound Used from the 180° sector : by far the most common entry Fly to the fix, then turn in the holding direction on to the outbound heading Start timing abeam the fix , or wings level if abeam cannot be found After the outbound time, turn inbound and intercept the holding track Arriving at a large angle? The first turn may be wider or tighter than usual: adjust the outbound leg to arrive on track Arrive from sector 3 Outbound 1 min Inbound Fix N
Chapter 9 · Holding Patterns
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The direct entry is the easy one, and it covers half the compass. You fly to the fix, and as you cross it you simply turn in the holding direction on to the outbound heading. Start the stopwatch when you are abeam the fix, or when the wings are level if you cannot tell when you are abeam. At the end of the outbound time, turn inbound and intercept the holding track. If you arrive at a big angle to the inbound track the first turn will be wider or tighter than normal, so adjust the outbound heading a little to make the inbound turn work out.
Sector 1
Parallel entry: fly back along the inbound track Cross the fix and turn left (right-hand hold) on to the outbound heading , parallel to the inbound track on the non-holding side Fly outbound for 1 minute Turn left again, towards the holding side , through more than 180° Either intercept the inbound track or fly direct to the fix On reaching the fix the second time, turn outbound: you are now in the hold The first turn of a parallel entry is opposite to the direction of the hold.
Arrive from sector 1 Parallel outbound 1 min Back to the fix Fix N
Chapter 9 · Holding Patterns
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The parallel entry is used when you arrive from sector one, from beyond the fix on the holding side. Cross the fix and turn on to the outbound heading, so that you fly parallel to the inbound track but on the non holding side. Hold that heading for one minute. Then turn towards the holding side, through a little more than one hundred and eighty degrees, and either intercept the inbound track or fly straight back to the fix. When you cross the fix the second time, turn outbound and you are established in the hold. Notice that the first turn of a parallel entry is the opposite way to the turns of the hold itself.
Sector 2
Offset entry: the teardrop Cross the fix and take up a heading 30° from the reciprocal of the inbound track , on the holding side Fly that heading for 1 minute (or to the limiting DME distance or radial) Turn in the holding direction to intercept the inbound track Track inbound to the fix and continue in the hold Right-hand hold: teardrop heading = outbound heading − 30° . Left-hand: + 30° Arrive from sector 2 Teardrop 240° · 1 min Inbound Fix N
Chapter 9 · Holding Patterns
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The offset entry, or teardrop, serves the seventy degree sector. Cross the fix and turn on to a heading that makes thirty degrees with the reciprocal of the inbound track, on the holding side. For a right hand hold that is the outbound heading minus thirty; for a left hand hold, plus thirty. Fly it for one minute, then turn in the holding direction to intercept the inbound track and fly back to the fix. In our example the inbound track is zero nine zero, the outbound heading is two seven zero, so the teardrop heading is two four zero.
Choosing the entry quickly
A method that works on any heading indicator Step Right-hand (standard) hold Left-hand hold 1 · Find the outbound heading Reciprocal of the inbound track Reciprocal of the inbound track 2 · Look at your heading indicator as you fly to the fix Mark a point 70° to the right of the nose Mark a point 70° to the left of the nose 3 · Outbound heading lies in the 70° slice Offset (teardrop)Offset (teardrop)4 · Outbound heading lies in the 110° slice on the other side Parallel Parallel 5 · Outbound heading lies in the bottom half Direct Direct
Example: heading 030° to the fix, hold inbound 090° right turns. Outbound 270° is 120° left of the nose: bottom half, so the entry is direct .
Chapter 9 · Holding Patterns
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a quick way to choose the entry using nothing but the heading indicator. First work out the outbound heading: the reciprocal of the inbound track. Now, flying towards the fix, look at the heading indicator. For a standard right hand hold, imagine a line from seventy degrees right of the nose across to the opposite side. If the outbound heading falls in the small seventy degree slice to the right of the nose, the entry is offset. If it falls in the one hundred and ten degree slice to the left of the nose, it is parallel. If it falls anywhere in the bottom half of the instrument, it is direct. For a left hand hold, mirror the picture.
Timing
The inbound leg must last one minute Still air outbound time: 1 minute at or below 14,000 ft , 1½ minutes above Start timing abeam the fix ; if abeam cannot be determined, when the wings are level outbound Time the inbound leg from wings level to the fix Inbound too long? Shorten the next outbound leg. Too short? Lengthen it Rule of thumb: correct outbound by the inbound error (some schools use half for a tailwind outbound) Where a DME distance limits the leg, turn inbound at the distance, whatever the clock says Inbound: aim for 1:00 Outbound: adjust this Fix Abeam: start clock Inbound took 1:20 → next outbound 0:40 Inbound took 0:45 → next outbound 1:15 Inbound took 1:00 → keep the same outbound
Chapter 9 · Holding Patterns
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The whole point of timing is to make the inbound leg last one minute. In still air the outbound leg is one minute at or below fourteen thousand feet, and one and a half minutes above. Start the clock abeam the fix, or when the wings are level if you cannot identify abeam. Then time the inbound leg, from rolling wings level to crossing the fix. If the inbound leg took too long, you went too far out, so shorten the next outbound leg. If it was too short, lengthen it. A simple rule is to change the outbound time by the amount of the inbound error. And if the hold is limited by a D M E distance, turn inbound at that distance regardless of the clock.
Wind
Crosswind: triple the drift on the outbound leg Find the drift correction that holds the inbound track: it is the only leg with guidance The two turns are flown at rate one and cannot be corrected , so wind drifts you during both Outbound, apply about three times the inbound correction, into the wind Example: 6° into wind inbound → about 18° into wind outbound Headwind outbound: fly longer . Tailwind outbound: fly shorter Never fly the turns at more than rate one or 25° bank, whichever needs less bank Inbound: 6° into wind Outbound: 18° into wind Fix N
Chapter 9 · Holding Patterns
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now add a crosswind. The inbound leg is the only one with track guidance, so use it to find the drift correction that keeps you on the holding track. Suppose that is six degrees into wind. You cannot correct during the turns, because they are flown at rate one, so the wind pushes you for two whole minutes without being opposed. To make up for that, on the outbound leg apply about three times the inbound correction, still into the wind. In our example that is eighteen degrees. For the along track component, a headwind on the outbound leg means you fly it longer, and a tailwind means you fly it shorter, always judged by that one minute inbound.
Speeds and clearances
Maximum holding speeds and what ATC will tell you Level Normal conditions Turbulence Up to 14,000 ft 230 kt (170 kt where the hold is limited to categories A and B)280 kt (170 kt for A and B only holds)Above 14,000 ft to 20,000 ft 240 kt 280 kt or Mach 0.8, whichever is less Above 20,000 ft to 34,000 ft 265 kt 280 kt or Mach 0.8, whichever is less Above 34,000 ft Mach 0.83 Mach 0.83
Slow to holding speed within three minutes of reaching the fix . A clearance to hold includes the fix, direction, inbound track, turn direction if non-standard, level and an expected approach time (EAT) or onward clearance time: your fuel decision hangs on it.
Chapter 9 · Holding Patterns
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Holding areas are protected for a maximum speed, so know the limits. Up to fourteen thousand feet the maximum is two hundred and thirty knots. From there to twenty thousand feet it is two hundred and forty, then two hundred and sixty five knots up to thirty four thousand feet, and Mach zero point eight three above that. In turbulence you may use two hundred and eighty knots or Mach zero point eight, after telling the controller. Reduce to holding speed within three minutes before the fix. A holding clearance names the fix, the direction from it, the inbound track, the direction of turns if they are not standard, the level, and an expected approach time. That time matters: compare it with your fuel, and decide early whether you can wait or must divert.
Summary
What to carry into the cockpit and the exam Pattern Right turns are standard. Inbound, rate one turn, outbound, rate one turn: about four minutes.
Entries Sector 1 parallel (110°), sector 2 offset (70°), sector 3 direct (180°), with 5° tolerance.
Timing 1 min up to 14,000 ft, 1½ min above. Start abeam. Adjust outbound to make inbound 1 minute.
Wind Find the drift inbound, triple it outbound. Headwind outbound = longer leg.
Offset Teardrop heading is 30° from the outbound heading, towards the holding side, for 1 minute.
Speeds 230 kt to 14,000 ft, 240 to FL200, 265 to FL340, M0.83 above. Know your EAT.
Chapter 9 · Holding Patterns
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us sum up. The standard hold has right turns and takes about four minutes. The entry depends on your heading at the fix: parallel from the one hundred and ten degree sector, offset from the seventy degree sector, and direct from the remaining half. Outbound time is one minute up to fourteen thousand feet and one and a half above, started abeam the fix and adjusted to give a one minute inbound leg. In a crosswind, triple the inbound drift correction on the outbound leg. Keep within the holding speed for your level, and always know your expected approach time.