IFR Training · Chapter 10
The ILS Approach Brief the approach, intercept the localiser, capture the glide path and fly both needles down to the decision altitude.
Intercept heading 120° Level: glide path above On the glide path · 3° N © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
The I L S is the approach that brings airliners down to the runway in fog. It gives you two needles: one for left and right, one for up and down. Keep them both centred and you arrive over the threshold, on the centre line, at the right height. It is the most precise approach you will fly, and also the most sensitive, so it has to be planned before you start. We begin with the briefing, and then fly the approach from the intercept to the decision.
Roadmap
Brief it, intercept it, fly the needles, decide The briefing Chart, aids, courses, altitudes, minima and the missed approach , before you begin.
The system Localiser for left and right, glide path for up and down, markers or DME for distance.
Flying it Intercept from below, then small corrections : a few degrees of heading, a little pitch.
The decision At decision altitude : visual references and land, or go around at once.
Chapter 10 · The ILS Approach
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are four parts. The approach briefing, which applies to every approach you ever fly. The I L S system and its signals. The technique for intercepting and flying it. And finally the decision at the bottom, with the missed approach.
Before you start
The approach briefing: say it aloud, in the same order, every time 1 · The chart Airport, procedure title, runway and chart date . Is it the one ATC cleared you for?
2 · Aids Frequencies and idents of the ILS, VOR, NDB, DME. Tuned, identified, set.
3 · Courses Final approach course and any intermediate tracks. Course bars set.
4 · Altitudes MSA , platform altitude, altitude at the FAF or marker, check altitude on the glide path.
5 · Minima DA or MDA , the required RVR or visibility , and where to look for the runway.
6 · Missed approach The first actions and the first turn and altitude, from memory.
7 · Aircraft Speeds, flap and gear schedule, rate of descent for the expected ground speed.
8 · Threats Weather, terrain, fuel and alternate . What will we do if we go around?
Chapter 10 · The ILS Approach
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before any approach, brief it. Say it aloud, in the same order every time, even when you are flying alone. One: the chart. The airport, the procedure, the runway and the date. Two: the aids. Frequencies and identifications, tuned and checked. Three: the courses, with the course bars set. Four: the altitudes. Minimum sector altitude, platform altitude, and the check altitude at the final approach fix. Five: the minima, both the decision altitude and the visibility you need. Six: the missed approach, at least the first actions, the first turn and the first altitude, from memory. Seven: the aircraft, with speeds, configuration and the expected rate of descent. Eight: the threats, including fuel and the alternate.
The system
Two radio beams that cross along the approach path Localiser : a vertical sheet along the extended centre line. Aerial at the far end of the runwayGlide path : a sloping sheet, normally 3° . Aerial beside the touchdown zone Where they cross is the approach path, ending about 50 ft above the threshold Marker beacons or, more often now, a DME give distance to goApproach and runway lights complete the system: they are what you see at the minimaOne frequency selection tunes localiser, glide path and paired DME together Intercept heading 120° Level: glide path above On the glide path · 3° N
Chapter 10 · The ILS Approach
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
An I L S is two radio beams. The localiser is like a thin vertical sheet standing along the extended centre line of the runway. Its aerial is at the far end of the runway, and it tells you whether you are left or right. The glide path is a sloping sheet, normally at three degrees, from an aerial beside the touchdown zone. It tells you whether you are high or low. Where the two sheets cross is the approach path, which passes about fifty feet above the threshold. Distance to go comes from marker beacons, or more often today from a D M E. And the approach and runway lights are part of the system too, because they are what you will see at the minima.
The signals
What each part transmits, and how sensitive it is Component Frequency Full-scale deflection Coverage Localiser VHF 108.10 to 111.95 MHz (odd first decimal) 2.5° each side: about 0.5° per dot 25 NM within ±10°, 17 NM within ±35° Glide path UHF 329 to 335 MHz, paired automatically About 0.7° above and below 10 NM within ±8° of the centre line Outer marker 75 MHz · 400 Hz · dashes · blue — About 4 NM from the threshold Middle marker 75 MHz · 1300 Hz · dots and dashes · amber — About ½ NM: near Cat I minima Inner marker 75 MHz · 3000 Hz · dots · white — Near the threshold
The localiser is four times as sensitive as a VOR. Glide path signals can form false lobes at steeper angles, which is why you always capture it from below .
Chapter 10 · The ILS Approach
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
A few numbers. The localiser transmits in the V H F band, on frequencies with an odd first decimal between one hundred and eight and one hundred and twelve megahertz. Full scale deflection is only two and a half degrees each side, so it is four times as sensitive as a V O R. The glide path transmits in U H F and is paired with the localiser frequency automatically. Its full scale deflection is only about zero point seven of a degree above and below. Marker beacons all transmit on seventy five megahertz: the outer marker gives blue dashes, the middle marker amber dots and dashes, and the inner marker white dots. One more point: the glide path can produce false lobes at steeper angles, which is why you always capture it from below.
Intercepting
Capture the localiser first, then the glide path from below Join at the platform altitude , on a heading that cuts the localiser at about 30° When the localiser needle comes alive , turn on to the final approach course Established on the localiser, level , the glide path needle is above you and moving down Glide path one dot above : gear down and landing flap, as your type requires Glide path centred : lower the nose about 3°, reduce power, set the rate of descent At the final approach fix or marker , cross-check the altimeter against the chart Intercept heading 120° Level: glide path above On the glide path · 3° N
Chapter 10 · The ILS Approach
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The I L S is always joined in the same order: localiser first, then the glide path, from below. You arrive at the platform altitude on a heading that cuts the localiser at about thirty degrees. When the localiser needle comes alive, turn on to the final approach course and settle on it. You are now flying level, with the glide path needle above you, moving slowly down. When it is about one dot above, select the landing gear and landing flap as your aircraft requires. As it centres, lower the nose by about three degrees, reduce the power, and set the rate of descent. Then, passing the final approach fix or the outer marker, check that your altimeter agrees with the altitude printed on the chart.
Reading the needles
Fly towards the needles, gently Localiser needle left : the centre line is to your left. Turn left Glide path needle up : the glide path is above you. Reduce the rate of descent The beams narrow as you approach: the same error shows as a bigger deflection Corrections must get smaller all the way down Beyond half scale on either needle near the minima, the approach is unstable Full scale on either needle below 1,000 ft: go around N 3 6 E 12 15 S 21 24 W 30 33 On the localiser and on the glide path N 3 6 E 12 15 S 21 24 W 30 33 Right of centre line: turn left N 3 6 E 12 15 S 21 24 W 30 33 Below the glide path: reduce descent N 3 6 E 12 15 S 21 24 W 30 33 Left and high: right, and descend
Chapter 10 · The ILS Approach
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Reading the needles is simple: fly towards them. If the localiser needle is to the left, the centre line is to your left, so turn left. If the glide path needle is above the centre, the glide path is above you, so reduce your rate of descent. What makes the I L S demanding is that the beams get narrower as you approach the runway. The same small error shows as a bigger and bigger deflection. So your corrections must get smaller all the way down. If either needle goes beyond half scale close to the minima, the approach is not stable. And if either needle reaches full scale below one thousand feet, do not try to rescue it. Go around.
Corrections
Heading for the localiser, pitch for the glide path, power for speed Find a reference heading that holds the localiser, then correct in steps of 2° to 5° Close in, use 1° or 2° . Never bank more than about half the heading change Hold the glide path with pitch : changes of 1° or less Hold the speed with power Rate of descent on 3° ≈ ground speed × 5 : 90 kt → 450 ft/min, 120 kt → 600 ft/min A headwind reduces the rate needed; expect to change power if the wind changes on the way down N 3 6 E 12 15 S 21 24 W 30 33 Heading 093°: 3° of drift, bar centred 20 10 10 20 Pitch: about 2½° nose down 20 15 10 5 0 5 10 15 20 VERT SPEED ×100 FPM 500 ft/min at 100 kt ground speed 40 60 80 100 120 140 160 180 200 AIRSPEED KNOTS Speed held with power
Chapter 10 · The ILS Approach
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each needle has its own control. For the localiser, find a reference heading that holds the needle still, allowing for drift, and then correct in small steps: two to five degrees further out, and only one or two degrees close in. For the glide path, use pitch, in changes of one degree or less. And hold the airspeed with power. A good approach starts from known numbers. On a three degree glide path, the rate of descent in feet per minute is about five times the ground speed in knots. So at ninety knots you need about four hundred and fifty feet per minute, and at one hundred and twenty knots, six hundred. A headwind reduces the rate you need, so if the wind changes on the way down, expect to change the power.
The decision
Decision altitude and the categories of ILS Category Decision height Minimum RVR Remarks Cat I Not lower than 200 ft 550 m (or visibility 800 m)The standard ILS, flown manually or coupled Cat II Below 200 ft, not lower than 100 ft 300 m Special aircraft equipment, crew training and airport approval Cat III Below 100 ft, or no decision height Less than 300 m, down to very low values Automatic landing: fail-passive or fail-operational systems
DA is read on the pressure altimeter (QNH); DH is the same point as a height above the threshold. Your own minima are the highest of the chart, the operator, the aircraft and your own qualification.
Chapter 10 · The ILS Approach
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The minimum on a precision approach is a decision altitude. It is not a level off altitude. It is the point at which you decide. For a category one I L S, which is the standard one, the decision height is not lower than two hundred feet above the threshold, and the runway visual range must be at least five hundred and fifty metres. Category two goes down to one hundred feet with three hundred metres, and category three goes lower still, even to no decision height at all, using automatic landing. Categories two and three need special aircraft equipment, crew training and airport approval. Remember that the minima you use are always the highest of those on the chart, those of your operator, your aircraft and your own qualification.
At the minima
At decision altitude: land, or go around at once Approaching DA, the pilot flying stays on instruments; look up only at the call To continue you need the required visual reference : approach lights, threshold, touchdown zone or runway lights, clearly in view and the aircraft in a position to land normally Nothing seen, or not stable: go around immediately . Do not level off and look Power, pitch up, positive rate, gear up, flap as required Then fly the published missed approach , and tell ATC Final approach Missed approach: climb N
Chapter 10 · The ILS Approach
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
So what happens at decision altitude? As you approach it, stay on the instruments. At the altitude, look up. To continue, you must have the required visual reference clearly in view, such as the approach lights, the threshold, or the touchdown zone, and the aircraft must be in a position to land normally. If you see nothing, or the approach is not stable, go around immediately. Do not level off and search for the runway: you are only two hundred feet above the ground. The actions are power, pitch up to the climb attitude, confirm a positive rate of climb, landing gear up, and flap as required. Then fly the published missed approach procedure, and tell air traffic control.
Radar approaches
When the controller is your instrument Precision approach radar The controller watches you in azimuth and elevation and talks you down continuously: "slightly left, turn right two degrees … on the glide path". A precision approach, to a decision altitude.
Surveillance radar approach Azimuth only. The controller gives headings and recommended altitudes at each mile . A non-precision approach, to an MDA.
How to fly them Make small, prompt heading changes exactly as given. Do not acknowledge on final unless asked. If you hear nothing for a few seconds , expect to go around.
Chapter 10 · The ILS Approach
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Finally, two approaches where the controller is your instrument. In a precision approach radar, or P A R, the controller watches your position in both azimuth and elevation, and talks you down continuously, with instructions such as turn right two degrees, or slightly above the glide path. It is a precision approach, flown to a decision altitude. In a surveillance radar approach, the controller has azimuth only. You are given headings to steer, and a recommended altitude at each mile from touchdown. That is a non precision approach, flown to a minimum descent altitude. In both, make small and prompt heading changes exactly as given. And if the controller goes silent for more than a few seconds on final, expect to go around.
Summary
What to carry into the cockpit and the exam Brief Chart, aids, courses, altitudes, minima, missed approach, aircraft, threats.
Signals Localiser full scale 2.5°; glide path 0.7°. Four times as sensitive as a VOR.
Intercept About 30° to the localiser, at platform altitude. Glide path from below.
Fly Heading for localiser, pitch for glide path, power for speed. Rate ≈ ground speed × 5.
Decide Cat I: 200 ft and RVR 550 m. Visual reference and stable, or go around.
Go around Power, pitch, positive rate, gear, flap. Fly the published procedure.
Chapter 10 · The ILS Approach
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Brief every approach in the same order. The localiser is four times as sensitive as a V O R, with full scale at two and a half degrees. Intercept it at about thirty degrees from the platform altitude, and capture the glide path from below. Use heading for the localiser, pitch for the glide path, and power for speed, with a rate of descent of five times your ground speed. At decision altitude, either you have the visual reference and a stable aircraft, or you go around at once: power, pitch, positive rate, gear, flap, and the published procedure.