IFR Training · Chapter 11
Non-Precision Approaches Approaches with no glide path: VOR, NDB and localiser-only. Minimum descent altitude, the constant-angle descent, timing and the missed approach point.
Level to the FAF Continuous 3° descent N © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
On an I L S, a needle tells you whether you are high or low. On a non precision approach there is no such needle. You have a track to follow, a set of altitudes that you must not go below, and a point at which you must have the runway in sight or go around. The vertical path is yours to plan and to fly. That makes this the approach where planning matters most, and where most approach accidents have happened.
Roadmap
A track, a floor, and a point of decision The approach Lateral guidance only. MDA is a floor, and the MAPt is where you must decide.
Two techniques The old step-down , and the safer constant-angle descent.
Planning Rate of descent, timing from the FAF, and the visual descent point .
Discipline Tracking tolerances, altimeter checks and the stabilised approach .
Chapter 11 · Non-Precision Approaches
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
We begin with what a non precision approach is and the fixes that define it. Then the two ways of flying the descent. Then the planning: rate of descent, timing, and where you should expect to see the runway. And finally the discipline that keeps it safe.
The approach
Lateral guidance only: the vertical path is up to you VOR approach Track a radial to or from a VOR, with DME or timing for distance. Tolerance half scale (5°) .
NDB approach Track a QDM or QDR. The least accurate: tolerance ±5° , and no flag.
Localiser only An ILS with the glide path unserviceable or not used. Accurate laterally, higher minima .
Radar (SRA) Headings and advisory altitudes from the controller.
FAF Final approach fix : where the final descent begins and the clock is started.
Step-down fix A fix with a minimum altitude that protects you from an obstacle below the approach.
MDA Minimum descent altitude : a floor. You may level at it, but never go below without visual reference.
MAPt Missed approach point : a fix, a DME distance or a time. Nothing seen here → go around.
Chapter 11 · Non-Precision Approaches
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A non precision approach gives you lateral guidance only. The main types are the V O R approach, the N D B approach, the localiser only approach, and the surveillance radar approach. Four terms define the final segment. The final approach fix is where the final descent begins, and where you start the stopwatch. A step down fix is a fix with a minimum altitude, which protects you from an obstacle below the approach path. The minimum descent altitude is a floor: you may fly level at it, but you may never go below it without the required visual reference. And the missed approach point, which may be a fix, a D M E distance or a time from the final approach fix, is where you must go around if you have not seen the runway.
Technique 1
Step-down: descend, level, descend, level At the FAF, descend promptly to the next minimum altitude Level off at each step-down altitude until past the fixThen descend to the MDA and level off again Fly level at MDA to the MAPt , looking for the runway Each level-off needs a large change of power, pitch and trim at low level High workload, an unstable approach, and a long time spent low: avoid it where you can Level to the FAF Descend to the step-down altitude Level at MDA Missed approach N
Chapter 11 · Non-Precision Approaches
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The traditional way to fly it is the step down technique, sometimes called dive and drive. At the final approach fix you descend promptly to the next minimum altitude. You level off there until you have passed the step down fix. Then you descend to the minimum descent altitude and level off again, and you fly level at that altitude all the way to the missed approach point, looking for the runway. It works, and the chart protects you if you do it accurately. But every level off needs a big change of power, pitch and trim, close to the ground. The workload is high, the approach is never stable, and you spend a long time at low altitude. So it is no longer the preferred method.
Technique 2
Constant angle: one stable descent to the runway Plan one continuous descent from the FAF, normally at 3° , aimed at the threshold It must still pass at or above every step-down altitude : check them against DME Fly it like an ILS without a glide path needle: constant rate, constant speed, constant configuration Do not level off at MDA Arriving at the MDA (many operators add a small margin) with no visual reference: go around at once Stable, lower workload, quieter, and it puts you where a normal landing is possible Level to the FAF Continuous 3° descent N
Chapter 11 · Non-Precision Approaches
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The preferred method is the constant angle descent. From the final approach fix you plan one continuous descent, normally at three degrees, aimed at the runway threshold. It must still pass at or above every step down altitude, so you check your altitude against the D M E on the way down. You fly it just like an I L S without the glide path needle: constant rate of descent, constant speed, constant configuration. The key difference from the old method is that you do not level off at the minimum descent altitude. You treat it as a decision point. If you arrive there without the visual reference, you go around at once. The approach is stable, the workload is lower, and you arrive where a normal landing is possible.
Planning
Rate of descent and time for a 3° final of 5 NM Ground speed Rate of descent on 3° (GS × 5) Time for 5 NM Height lost per NM 70 kt 350 ft/min 4 min 17 s ≈ 320 ft 90 kt 450 ft/min 3 min 20 s ≈ 320 ft 100 kt 500 ft/min 3 min 00 s ≈ 320 ft 120 kt 600 ft/min 2 min 30 s ≈ 320 ft 140 kt 700 ft/min 2 min 09 s ≈ 320 ft
Use ground speed , not airspeed: apply the wind first. Time = distance × 60 ÷ ground speed. Make a DME against altitude check at every mile: about 300 ft per NM .
Chapter 11 · Non-Precision Approaches
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The planning is simple arithmetic, and you do it before the approach, not during it. First work out your ground speed on final by applying the wind to your approach speed. The rate of descent for three degrees is five times the ground speed: four hundred and fifty feet per minute at ninety knots, six hundred at one hundred and twenty. The time from the final approach fix to the missed approach point is the distance times sixty, divided by the ground speed. For five miles at one hundred knots, that is three minutes. Start the stopwatch at the final approach fix on every approach, even when you have D M E, as a backup. And on the way down, check your altitude at each mile: you should lose about three hundred feet per nautical mile.
Where to look
The visual descent point: the last place a normal landing can start The MAPt is often at or near the threshold: too close to land from MDA The VDP is where a normal 3° path from the runway meets the MDA Distance from the threshold ≈ height of the MDA above the threshold ÷ 300 See the runway before the VDP: continue down the normal path See it only after the VDP: a landing would need a steep, unstable descent. Go around Do not turn early: the missed approach track still starts at the MAPt VDP MAPt MDA normal 3° path distance = height above threshold ÷ 300 MDA 450 ft above the threshold → 1.5 NM too steep
Chapter 11 · Non-Precision Approaches
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a trap. The missed approach point is often at or close to the runway threshold. If you are level at the minimum descent altitude and you first see the runway there, you cannot land from it: you are several hundred feet above the threshold with no distance left. So work out a visual descent point. It is where a normal three degree path from the runway meets the minimum descent altitude, and its distance from the threshold is the height of the minimum descent altitude above the threshold, divided by three hundred. If that height is four hundred and fifty feet, the visual descent point is one and a half miles out. See the runway before it, and you continue. See it only after, and you go around.
Accuracy
Tolerances and checks on final Track VOR and localiser: within half scale . NDB: within ±5° . Outside that on final → go around .
Altitude Never below a published minimum. Level-offs within +100 ft, −0 ft of the MDA.
Altimeter QNH set and cross-checked. One hPa wrong is about 30 ft. In very cold air the aircraft is lower than indicated.
Ident Aid identified , and for an NDB the ident monitored throughout.
Timing Clock started at the FAF, every time .
Calls "1,000 to go", "100 above", "minimum": say them aloud, even single pilot.
Chapter 11 · Non-Precision Approaches
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Accuracy on a non precision approach has hard limits. Laterally, you must stay within half scale deflection on a V O R or localiser, and within five degrees on an N D B. If you are outside that on final, go around. Vertically, you are never below a published minimum altitude. The altimeter deserves special care, because it is your only vertical reference. Check the Q N H is set and cross checked: an error of one hectopascal is about thirty feet. And remember that in very cold air the aircraft is lower than the altimeter shows. Identify the aid, and for an N D B keep monitoring the ident. Start the clock at the final approach fix. And make the standard calls aloud, even when you are alone.
Discipline
The stabilised approach: all of these, or go around By 1,000 ft above the aerodrome in instrument conditions (500 ft in visual conditions) the approach must be stable, and must stay stable.
On the path On track and on the planned vertical path, needing only small corrections .
On speed Approach speed within about +10 / −5 kt , power set for the configuration.
Configured Landing gear down, landing flap set , checklist complete.
Rate of descent Not more than about 1,000 ft/min , and steady.
Briefed Missed approach reviewed, minima set, both pilots, or both halves of your mind, agreed.
If not Go around. A go-around is a normal manoeuvre, not a failure.
Chapter 11 · Non-Precision Approaches
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
All of this comes together in one idea: the stabilised approach. By one thousand feet above the aerodrome in instrument conditions, or five hundred feet in visual conditions, the approach must be stable and it must stay stable. That means you are on track and on the planned vertical path, needing only small corrections. You are on speed. The landing gear is down, the landing flap is set, and the checklist is complete. The rate of descent is steady and not more than about one thousand feet per minute. And the missed approach has been briefed. If any one of these is missing, go around. A go around is a normal manoeuvre. It is not a failure, and nobody has ever been hurt by flying a second approach.
Summary
What to carry into the cockpit and the exam No glide path Lateral guidance only. You plan and fly the vertical path.
MDA A floor, not a decision height. Never below without visual reference.
Constant angle One 3° descent from the FAF. Do not level at MDA: land or go around.
Numbers Rate = ground speed × 5. Time = distance × 60 ÷ ground speed. 300 ft per NM.
VDP Height above threshold ÷ 300. Runway seen after it → go around.
Stable On path, on speed, configured by 1,000 ft, or go around.
Chapter 11 · Non-Precision Approaches
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. A non precision approach gives lateral guidance only, so the vertical path is yours to plan. The minimum descent altitude is a floor that you never go below without visual reference. Fly a constant angle descent from the final approach fix, and do not level off at the minima. The rate of descent is five times the ground speed, and you lose about three hundred feet per mile. Work out a visual descent point by dividing the height above the threshold by three hundred. And be stable by one thousand feet, or go around.