IFR Training · Chapter 5
VOR Indications How the VOR display works: the course selector, the deviation needle, the TO/FROM flag, the HSI, and how to find out exactly where you are.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
The V O R is the backbone of conventional instrument navigation, and its cockpit display is clever but easy to misread. The key to it is one fact that surprises most students: the instrument does not know which way the aircraft is pointing. It only knows where the aircraft is. Once you have really understood that, the needle, the flag and the course selector all fall into place.
Roadmap
The VOR shows position, not heading The signal VHF, line of sight, 360 radials. Tune, identify, check the flag.
The display Course selector, deviation needle with 2° dots , and a TO/FROM flag.
Orientation Centre the needle to find your radial or your QDM .
Over the station The cone of confusion and how to recognise station passage.
Chapter 5 · VOR Indications
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
First a short look at the signal and what can go wrong with it. Then the display itself, piece by piece. Then orientation: how to use the display to find out where you are. And lastly what happens as you fly over the top of the station.
The signal
A VHF beacon that tells you your radial Transmits on 108.00 to 117.95 MHz : VHF, so line of sight only Range depends on height: roughly 1.23 × √height in feet nautical miles to the radio horizon The receiver compares two signals to find the radial you are on Typical overall accuracy: about ±5° Identify the station by its Morse code before use, and monitor itA warning flag (NAV or OFF) means the signal is unusable: do not navigate on it 360° 090° 180° 270° VOR N
Chapter 5 · VOR Indications
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A V O R is a ground beacon transmitting in the V H F band, between one hundred and eight and one hundred and seventeen point nine five megahertz. Being V H F, it works by line of sight, so the range depends on your height. The aircraft receiver compares two signals from the station and from the difference works out which radial you are on. The overall accuracy of the system is about plus or minus five degrees. Before you use any V O R, do three things: tune it, identify it by listening to its Morse code, and check that there is no warning flag. A flag means the signal cannot be trusted, and you must not navigate on it.
The display
Course selector, deviation needle and TO/FROM flag The OBS knob rotates the card to select a course The course deviation needle shows whether that course line is to your left or right Each dot is 2° ; full scale is 10° either side The TO/FROM flag shows whether the selected course would take you to or from the station Needle centred with TO : the selected course is your QDM Needle centred with FROM : the selected course is your radial N 3 6 E 12 15 S 21 24 W 30 33 TO OBS 030° · centred · TO N 3 6 E 12 15 S 21 24 W 30 33 TO Two dots right: course is 4° to the right N 3 6 E 12 15 S 21 24 W 30 33 FR OBS 210° · centred · FROM N 3 6 E 12 15 S 21 24 W 30 33 TO Full scale: 10° or more
Chapter 5 · VOR Indications
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The basic display is the course deviation indicator. It has three parts. The omni bearing selector, or O B S, is a knob that rotates the compass card so that you can choose a course. The deviation needle shows whether that course line lies to your left or to your right. Each dot is two degrees, and full scale is ten degrees either side. And the to from flag tells you whether the selected course would take you towards the station or away from it. From this come two useful facts. If the needle is centred with a TO flag, the selected course is your Q D M. If it is centred with a FROM flag, the selected course is the radial you are on.
The big idea
The indication depends on position, not on heading The selected course line and a line at right angles through the station divide the map into four areas Beyond the station along the course: FROM . Before it: TO Left of the course line: needle right . Right of it: needle left Turn the aircraft through a full circle on the spot: nothing on the CDI changes The needle points towards the course line only when your heading roughly agrees with the selected course Abeam the station, on the 90° line, the flag is ambiguous or OFF Selected course 360° FROM FROM TO TO needle RIGHT needle LEFT needle RIGHT needle LEFT Same indication whatever the heading
Chapter 5 · VOR Indications
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the big idea. The V O R receiver has no idea which way the aircraft is pointing. Picture the course you have selected drawn as a line through the station, and a second line through the station at right angles to it. Together they divide the map into four areas. If you are beyond the station in the direction of the course, the flag shows FROM. If you are short of it, the flag shows TO. If you are to the left of the course line, the needle is to the right, and the other way round. You could spin the aircraft through a complete circle on the spot and nothing on the instrument would change. The needle only works as a command, fly towards me, when your heading roughly agrees with the course you have selected.
Orientation
Centre the needle to find out where you are Tune and identify the station; check there is no flagTurn the OBS until the needle centres with FROM : read your radial at the top Or centre it with TO : read your QDM , the course direct to the station Plot or visualise: station in the middle of the heading indicator, you on the radial A DME distance, or a radial from a second VOR, turns the line into a fix To fly direct to the station: centre with TO, turn to that heading, then correct for drift Radial 060° Radial 090° Radial 120° Heading 150° VOR N
Chapter 5 · VOR Indications
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
So how do you find out where you are? Tune and identify the station, and check there is no flag. Then turn the O B S until the needle centres with a FROM flag. The number at the top of the card is the radial you are on. Alternatively, centre the needle with a TO flag, and the number at the top is your Q D M, the course that leads straight to the station. Now picture the station in the centre of your heading indicator, with yourself out on that radial. That one line, plus a D M E distance or a radial from a second station, gives you a fix. And if you want to go direct to the station, centre the needle with TO, turn on to that heading, and then correct for drift.
Needle sense
Fly towards the needle, but only when the course agrees with your heading Heading close to the selected course: the needle is a command . Needle left → turn left Flying inbound : select the inbound course and expect TO Flying outbound : select the outbound course and expect FROM Select the reciprocal by mistake and the needle works backwards: reverse sensing Rule: the number at the top of the card should be close to your heading An HSI removes the problem, because its needle turns with the compass card N 3 6 E 12 15 S 21 24 W 30 33 TO Heading 090°, OBS 090°: turn LEFT N 3 6 E 12 15 S 21 24 W 30 33 Heading 090° N 3 6 E 12 15 S 21 24 W 30 33 FR Heading 090°, OBS 270°: reversed! N 3 6 E 12 15 S 21 24 W 30 33 HSI: always the right way
Chapter 5 · VOR Indications
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
When your heading is close to the course you have selected, the needle becomes a command instrument. If the needle is to the left, the course is to your left, so you turn left. That is why, flying inbound, you select the inbound course and expect a TO flag, and flying outbound you select the outbound course and expect a FROM flag. But if you select the reciprocal by mistake, the needle works backwards. The same aircraft, in the same place, now shows the needle on the other side, and if you follow it you fly further from the course. This is reverse sensing. The protection is simple: the number at the top of the card should always be close to your heading.
The HSI
The horizontal situation indicator draws the picture for you Combines the heading indicator and the CDI in one instrument The course arrow is set with the course knob and turns with the compass card The centre section of the arrow, the deviation bar , moves off to one side The aircraft symbol is fixed in the middle: the bar shows the course line as seen from above A small triangle replaces the TO/FROM flag There is no reverse sensing , whatever the heading N 3 6 E 12 15 S 21 24 W 30 33 Heading 060° · course 030° bar ahead and right N 3 6 E 12 15 S 21 24 W 30 33 On course 030° inbound
Chapter 5 · VOR Indications
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The horizontal situation indicator, or H S I, does the visualising for you. It combines the heading indicator and the deviation indicator in one instrument. You set the course with a knob, and a course arrow appears on the compass card and turns with it as the aircraft turns. The centre section of the arrow is the deviation bar, which slides off to one side when you are off course. The little aircraft in the middle is you, and the bar is the course line, drawn as if you were looking down from above. In the first picture the bar is ahead and to the right, and the aircraft is already heading towards it at thirty degrees. Because the whole display turns with the heading, there is no reverse sensing.
Over the station
The cone of confusion and station passage Directly above the station there is no usable signal: the cone of confusion The needle becomes sensitive, swings from side to side, and the flag flickers The cone widens with height: at 6,000 ft above the station it lasts well under a minute at light aircraft speeds Do not chase the needle. Hold the heading that was workingStation passage : the first complete change of the flag from TO to FROM Then select the new outbound course if it changes, and start the clock if timing is required TO FROM VOR N
Chapter 5 · VOR Indications
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Directly above a V O R there is a region with no usable signal, shaped like an upturned cone, and called the cone of confusion. As you approach it the needle becomes very sensitive. Inside it, the needle swings from side to side and the flag flickers or shows off. The higher you are, the wider the cone and the longer it lasts. The rule is: do not chase the needle. Hold the heading that was keeping you on course, and wait. Station passage is the first complete change of the flag from TO to FROM. At that moment, select the new outbound course if it is different, turn on to it, and start your stopwatch if the procedure calls for timing.
How far off am I?
What a dot is worth Distance from the VOR One dot (2°) Full scale (10°) 60 NM 2 NM 10 NM 30 NM 1 NM 5 NM 15 NM ½ NM 2½ NM 5 NM about 1,000 ft under 1 NM
From the one-in-sixty rule: distance off = degrees off × distance ÷ 60 . The same needle position means a much smaller error close in, which is why the needle seems to speed up near the station.
Chapter 5 · VOR Indications
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
How far off course is one dot? It depends how far you are from the station. From the one in sixty rule, the distance off equals the degrees off, times the distance to the station, divided by sixty. So at sixty miles, one dot, which is two degrees, is two nautical miles. At thirty miles it is one mile. At fifteen miles it is half a mile, and at five miles it is only about a thousand feet. This explains something you will notice in the air. Close to the station the needle seems to speed up and become twitchy. The aircraft is not flying any worse: the same small sideways error is simply a bigger angle. So make smaller corrections as you get closer.
Summary
What to carry into the cockpit and the exam Before use Tune, identify, no flag. VHF: line of sight only.
CDI One dot = 2°, full scale = 10°. Centred with FROM = your radial; with TO = your QDM.
Position only The display ignores heading. Top of the card should agree with your heading.
Reverse sensing Reciprocal selected: the needle works backwards. The HSI is immune.
Cone of confusion Hold the heading. Passage = first complete TO-to-FROM change.
Sensitivity One dot at 30 NM is 1 NM. Smaller corrections close in.
Chapter 5 · VOR Indications
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Always tune, identify and check the flag. One dot is two degrees and full scale is ten. Centre the needle with FROM to read your radial, or with TO to read your Q D M. The display shows position, not heading, so keep the number at the top of the card close to your heading or you will get reverse sensing. Over the station, hold your heading through the cone of confusion and call station passage at the first complete flag change. And remember the needle gets more sensitive as you get closer.