Aircraft Instruments · Chapter 19
The air data system: inputs, configuration module, twin ADCs with independent and standby pitot-static systems, analogue and digital computers, the calculation chain, corrections, users, redundancy, BITE, advantages, servo displays and failures.
Exclusive study material prepared by eatpl.in
Arrow keys, the buttons or swipe to move between pages. The Lab is below the e-book.
Instruments · Chapter 19
One computer takes the probe pressures and temperatures and sends corrected air data to every system that needs it.
Why an ADC
The air data system
Integration
Inputs
Pitot-static layout
Static vents
Analogue ADC
Digital ADC
Outputs
| Output | Worked out from |
|---|---|
| Pressure altitude | Static pressure (ISA, 1013.25 hPa datum) |
| Baro-corrected altitude | Static pressure + pilot's baro setting |
| Vertical speed | Rate of change of pressure altitude |
| CAS (and IAS) | Pt − Ps (dynamic pressure), corrected |
| Mach number | Ratio (Pt − Ps) / Ps |
| SAT | TAT and Mach number |
| TAS | Mach × local speed of sound (from SAT) |
Also: overspeed warning (VMO/MMO), TAT display, density altitude and altitude alerting on many types.
The calculation chain
Practice
| Inputs (K = 1) | SAT(K) = TAT(K) ÷ (1 + 0.2 M²) | SAT | TAS = M × 38.94 √SAT |
|---|---|---|---|
| TAT −20 °C, M 0.80 | 253.1 ÷ 1.128 = 224.4 K | SAT −49 °C | 467 kt |
| TAT +5 °C, M 0.50 | 278.1 ÷ 1.050 = 264.9 K | SAT −8 °C | 317 kt |
| TAT −25 °C, M 0.84 | 248.1 ÷ 1.141 = 217.5 K | SAT −56 °C | 482 kt |
| TAT −8 °C, M 0.74 | 265.1 ÷ 1.110 = 239.0 K | SAT −34 °C | 445 kt |
Ram rise = TAT − SAT: about 29 °C at M 0.8, only about 13 °C at M 0.5.
Corrections
Who uses air data
System redundancy
Redundancy
Built-in test
Advantages
| Area | Mechanical instruments | Air data system |
|---|---|---|
| Displays | Fixed by the mechanism | Freedom of design: digital, moving tapes, combined displays |
| Instrument and lag errors | Linkage friction; slow response | Largely removed by servomotors |
| Error correction | Little or none | Shaped cams / software, e.g. PEC from the Mach channel used for height and speed |
| Other systems | Separate sensors needed | Central source of air data in many forms |
| Plumbing | Pipes to every instrument | Clean design: only standby lines; shorter lines, fewer acoustic errors |
| Failure warning | Visual cross-check left vs right | Comparison monitor, flags and warning lights |
Displays
Failures
| Situation | What the crew sees |
|---|---|
| ADC power or computer failure | Flags on that side's speed, altitude and V/S; autopilot modes using it drop out |
| Data invalid (BITE detects fault) | Flag or data removed from the display; caution message |
| Two sources disagree | Comparator alert, e.g. IAS DISAGREE / ALT DISAGREE |
| Probe blocked (e.g. iced pitot) | No flag: the ADC computes wrong values from wrong inputs: unreliable airspeed |
| Transponder source lost | Altitude reporting lost unless the other ADC is selected |
| Comparison monitor trips | Warning light on the instrument warning panel or central warning system |
A computer cannot fix a blocked probe: cross-check with attitude, power and the standby instruments.
Standby instruments
Exam traps
Summary