Static and total air temperature, the ram rise from compression heating, recovery factor, temperature scales, direct and remote reading thermometers, the heated and aspirated TAT probe, errors and how to find SAT from TAT.
Exclusive study material prepared by eatpl.in
Arrow keys, the buttons or swipe to move between pages. The Lab is below the e-book.
Instruments · Chapter 3
Air Temperature Measurement
Speed warms the air you try to measure. Learn how the probe reads it and how to get the true outside air temperature back.
Why it matters
What the temperature is used for
TAS: density depends on temperature, so CAS cannot be turned into TAS without it
Speed of sound and Mach number: LSS = 38.94 √T, so TAS = Mach × LSS needs T
Engine thrust settings: EPR and N1 limits and take-off thrust are scheduled against temperature
Aircraft performance: density altitude, take-off and climb data, fuel planning
Icing: airframe and engine anti-ice decisions depend on the outside temperature
Altimeter temperature error and the ISA deviation used in flight planning
Ram rise
Why a fast aircraft feels warmer air
At the sensor the air is slowed and compressed; its kinetic energy turns into heat
Mainly adiabatic compression, plus some friction (kinetic) heating
The rise in temperature is the ram rise, often called compressibility heating
It grows with the square of TAS: negligible at 100 kt, about 25 °C at 500 kt
So an exposed thermometer always reads warmer than the real air
Definitions
SAT, TAT and recovery factor
SAT (static air temperature, also OAT or COAT): the temperature of the undisturbed air
TAT (total air temperature): the temperature the air would reach if brought fully to rest adiabatically
Ram rise = TAT − SAT
Recovery factor (Kr): the fraction of the ram rise a sensor actually picks up
Kr = 1.0 gives TAT; Kr = 0.8 gives SAT + 80 % of the ram rise
IOAT (indicated OAT) is what the gauge shows; it lies between SAT and TAT
Terminology
Many names, two temperatures
Name
Meaning
Same as
SAT: static air temperature
Temperature of the undisturbed air
OAT, COAT (corrected outside air temperature)
TAT: total air temperature
Air brought fully to rest adiabatically: SAT + full ram rise
RAT (ram air temperature); a probe with Kr = 1
IOAT: indicated outside air temperature
What the gauge shows: SAT + Kr × ram rise
Indicated temperature
Ram rise
TAT − SAT
Heating error, temperature rise
Kr: recovery factor
Fraction of the ram rise the probe recovers
0.75 – 1.0
TAT = SAT + ram rise; IOAT = COAT + Kr × ram rise. Except at very low speed, IOAT is warmer than COAT.
Temperature scales
Celsius, kelvin and Fahrenheit
K = °C + 273 (273.15): use kelvin in every formula with a ratio, e.g. TAT/SAT or √T
°F = °C × 9/5 + 32; °C = (°F − 32) × 5/9
The scales cross at −40: −40 °C = −40 °F
ISA MSL: 15 °C = 288 K = 59 °F; tropopause −56.5 °C = 216.5 K
A temperature difference of 1 °C equals 1 K (but 1.8 °F)
Size of the ram rise
Ram rise grows with TAS squared
Rule of thumb: ram rise ≈ (V/100)² °C, V = TAS in knots
100 kt → 1 °C · 200 kt → 4 °C · 300 kt → 9 °C · 400 kt → 16 °C · 500 kt → 25 °C
Doubling TAS gives four times the ram rise
Below about 150 kt the error is small enough to ignore in light aircraft
The nav computer has a temperature-rise scale for the same correction
SAT = TAT − (V/100)²
Recovery factor
How much of the ram rise a sensor sees
Indicated temperature = SAT + Kr × ram rise
Modern TAT probes: Kr very close to 1.0, so they read TAT
Simple flush-mounted or direct-reading thermometers: Kr typically 0.75–0.9
Kr is found by flight test and given in the aircraft documents
A high, known Kr makes the correction back to SAT reliable
TAT = SAT + Kr × ram rise
Direct reading
The bimetallic strip
Two metals with very different coefficients of expansion, e.g. brass and Invar, bonded along their length
Heated, the brass expands much more than the Invar, so the strip bends (brass on the outside of the curve)
The amount of bend depends on the temperature rise, so it measures temperature
Wound into a helix, the strip twists instead and can turn a pointer directly
No electrical power needed: used in light aircraft and for temperature compensation in many instruments
Light aircraft
Direct reading thermometer
A bimetal strip: two metals with different expansion, e.g. brass and Invar, bonded together
Heating makes it bend; wound into a helix it twists and turns a pointer directly
Probe sticks out through the windscreen or skin, dial faces the pilot
Cheap and needs no power, but slow to respond and low recovery factor
Errors: sun heating the probe, ram rise at speed, ice on the probe
Electrical sensing
Remote reading: resistance thermometer
Sensing element: fine platinum wire whose resistance rises with temperature
It forms one arm of a resistance (Wheatstone) bridge or ratiometer
A temperature change unbalances the bridge: current flows through the moving-coil indicator, calibrated in °C
Reading can be sent to the gauge, the ADC, FMS and engine computers
Used in the TAT probe of every jet transport
Jet transport
Total head (immersion) TAT probe
Small strut and intake of nickel-plated beryllium copper (strong, good conductor) on the forward fuselage, outside the boundary layer
Air must turn through about 90° to reach the element; water and ice particles carry straight on and out
Bleed holes draw off the boundary-layer air, helped by the higher pressure inside the intake
Pure platinum wire element: almost negligible lag, Kr ≈ 1.00
Also called a total head or immersion probe
De-icing the probe
Probe heating and heater error
An electric heater in the strut and intake prevents ice forming on the probe
Self-compensating: its resistance rises as it warms, so the heater current falls
Dissipates a nominal 260 W in icing conditions
Heater error is small: about 0.9 °C at M 0.1, falling to about 0.15 °C at M 1.0
Larger at low speed because less air flows past to carry the heat away
On the ground
The aspirated TAT probe
On the ground there is no airflow: sunshine and hot ramps heat-soak the probe, so it reads too warm
An aspirator (air-to-air ejector) blows engine bleed air through a nozzle at the back of the probe
This creates a low pressure that draws outside air past the element at a steady rate
Gives a reliable temperature for take-off thrust setting and the autothrottle
An aspirated probe reads close to SAT on the ground (no ram rise)
Errors
What makes the temperature wrong
Error
Cause
Remedy
Instrument
Imperfections in manufacture
Calibration; correction card
Heating error
Adiabatic compression and kinetic (friction) heating at speed
Correct with Kr and M, or (V/100)²; ADC
Environmental: solar
Sun heating the sensor; hot ramp on the ground
Shielded mounting; aspirator
Environmental: ice
Ice accretion on the probe
Probe heater
Heater error
Heater warming the element
Small: 0.9 °C at M 0.1 to 0.15 °C at M 1.0
Time lag
Thermal inertia of the sensor
Fast platinum element
Getting SAT back
SAT from TAT: the exact formula
Use absolute temperatures (K = °C + 273) and the Mach number:
With a TAT probe take Kr = 1: TAT = SAT × (1 + 0.2 M²)
Example: M 0.80, SAT −50 °C (223 K): TAT = 223 × 1.128 = 251.5 K = −21.5 °C
Ram rise there is about 28.5 °C; TAS is only ≈ 465 kt, so the (V/100)² rule (≈ 22 °C) under-estimates it at high speed
The ADC does this continuously and displays both TAT and SAT
TAT = SAT × (1 + 0.2 Kr M²)
SAT = TAT ÷ (1 + 0.2 Kr M²)
In the cockpit
TAT in, SAT out
The TAT probe signal goes to the air data computer with the Mach number
The ADC solves SAT = TAT ÷ (1 + 0.2 Kr M²) continuously (kelvin)
Engine displays usually show TAT; flight displays and the FMS use SAT
SAT is then used for TAS, the speed of sound and performance
Example: M 0.80, TAT −21 °C → SAT ≈ −50 °C, ram rise ≈ 28.5 °C
Practice
Worked examples
Given
Working
Answer
TAT −20 °C, TAS 400 kt
ram rise = (400/100)² = 16
SAT −36 °C
SAT −45 °C, TAS 300 kt
ram rise = 9
TAT −36 °C
TAT +5 °C, TAS 500 kt
ram rise = 25
SAT −20 °C
IOAT −10 °C, Kr 0.8, ram rise 20
sensed rise = 0.8 × 20 = 16
SAT −26 °C
SAT 223 K, M 0.8, Kr 1
223 × (1 + 0.2 × 0.64)
TAT ≈ 251.5 K (−21.5 °C)
Always subtract the ram rise to go from TAT to SAT; SAT is the lower figure.
Navigation computer
Two-stage correction from IOAT
Step
Working
Result
Given
IOAT −25 °C, pressure altitude 20 000 ft, CAS 210 kt
—
1. Approximate TAS
Computer set with IOAT (too warm)
TAS ≈ 287 kt
2. Temperature rise
(2.87)² ≈ 8 °C (temp-rise scale)
rise ≈ 8 °C
3. COAT
−25 − 8
COAT = −33 °C
4. Recompute TAS
Computer set with COAT −33 °C
TAS ≈ 283 kt
If the first TAS is above about 300 kt, apply the compressibility correction to it before using the temperature-rise scale.
Operating data
Reading SAT from a TAT table
TAT (°C)
M .50
M .70
M .80
M .84
0
−13
−24
−31
−34
−10
−23
−33
−40
−43
−20
−32
−43
−49
−51
−30
−42
−52
−58
−60
−40
−51
−61
−66
−69
Values are SAT in °C for a probe with Kr = 1, from SAT = TAT ÷ (1 + 0.2 M²). The faster you fly, the bigger the gap.
Exam traps
Points that catch people out
TAT is the maximum temperature the air reaches when brought to rest adiabatically; SAT is always lower in flight
Ram rise comes from adiabatic warming (compression), not cooling; it grows with TAS² (500 kt → 25 °C)
Direct reading: different coefficients of expansion; remote reading: change of resistance with temperature; element is platinum
Thermometers are shielded against solar radiation
An aspirator lets the probe measure air temperature on the ground; it is not an anti-icing device
Kelvin in the formula; −40 °C = −40 °F
Summary
What to take into the exam
SAT = OAT = COAT; TAT = SAT + full ram rise; IOAT = SAT + Kr × ram rise
Ram rise from adiabatic compression (+ friction) ≈ (V/100)² °C; recovery factor Kr, TAT probe ≈ 1.0
TAT = SAT (1 + 0.2 Kr M²) in kelvin; K = °C + 273; °F = 9/5 °C + 32
Direct: bimetal (brass/Invar) helix; remote: platinum resistance in a bridge, moving-coil indicator
TAT probe: beryllium copper, 90° turn, bleed holes, self-compensating heater (small heater error), aspirator for ground use
Errors: instrument, environmental (sun, ice), heating; IOAT → TAS → rise → COAT → TAS on the computer