How the airspeed indicator turns dynamic pressure into knots: principle, construction, ISA MSL calibration, density, compressibility, instrument and position errors, IAS to CAS to EAS to TAS, markings and V-speeds, speed tapes, blockages, leaks and checks.
Exclusive study material prepared by eatpl.in
Arrow keys, the buttons or swipe to move between pages. The Lab is below the e-book.
Instruments · Chapter 4
The Airspeed Indicator
A differential pressure gauge that turns dynamic pressure into knots: construction, calibration, errors, the speeds IAS to TAS, markings, blockages and checks.
Principle
A differential pressure gauge
Pitot pressure = dynamic + static: P = PE + S (dynamic is also called pitot excess)
Pitot pressure is fed into a thin metal capsule; static fills the sealed case around it
Static acts inside and outside, so it cancels: the capsule responds only to Pt − Ps = dynamic pressure
More speed → more dynamic pressure → capsule expands → pointer moves
Dynamic pressure = ½ρV², so the ASI senses density as well as speed
The principle in a box
A diaphragm between two pressures
Picture an airtight box split by a flexible diaphragm
Pitot (Ps + q) on one side, static (Ps) on the other
Net pressure across it = (Ps + q) − Ps = q: static has no effect on the movement
The diaphragm deflects in proportion to dynamic pressure; levers carry this to the needle
The real instrument uses a capsule inside the case instead of a flat diaphragm
Construction
Inside the ASI
Pitot pressure inside a thin capsule of phosphor-bronze or beryllium-copper; static in the hermetically sealed case
Capsule movement passes through a temperature-compensated magnifying linkage: rocking shaft, sector gear and pinion
A hairspring takes up backlash; a bimetal compensates for temperature
q ∝ V², so the linkage is shaped to give a more even scale
Tolerance (large aircraft): ±3 % or 5 kt, whichever is greater
Calibration
Calibrated for ISA at mean sea level
The scale is calculated for ISA MSL: 1013.25 hPa, +15 °C, dry air, density 1225 g/m³ (1.225 kg/m³)
No allowance is made for the change of density with altitude
Compressibility appropriate to MSL ISA is built into the calibration
IAS = TAS only in ISA MSL conditions, with no instrument or position error
Higher up, lower density means the ASI reads less than TAS
q = ½ ρ V² (incompressible)
Pt − Ps = f(V, ρ₀, P₀) (calibration law)
Density error
Thin air, low reading
Dynamic pressure is proportional to density: the same TAS in thinner air gives less q
Less q → less capsule movement → the ASI under-reads the TAS at altitude
Example: TAS 200 kt at 20 000 ft ISA (σ ≈ 0.53) gives only about 146 kt on the ASI
Below MSL (density above 1.225 kg/m³) the ASI would over-read
Correcting CAS (or EAS) for density error gives TAS: the correction is nearly always added
From the dial to the truth
IAS → CAS → EAS → TAS
IAS: what the pointer shows
CAS = IAS corrected for instrument and position error (correction card or ADC)
EAS = CAS corrected for compressibility (always subtracted)
TAS = EAS corrected for density: TAS = EAS × √(ρ₀/ρ)
Below about 300 kt TAS, compressibility can be ignored: go straight CAS → TAS
Errors
The ASI errors
Error
Cause
Note
Instrument
Manufacturing tolerances, friction, wear
On a correction card
Position (pressure)
Static vent and pitot not sensing true pressures
Varies with speed, AoA, flap
Manoeuvre-induced
Rapid change of attitude disturbs the flow
Short-lived; also lag
Compressibility
Air compressed at the pitot more than the MSL law assumes
ASI over-reads; subtract
Density
Air density differs from ISA MSL
Correct with pressure alt and temperature
Blockage / leak
Ice, insects, water, broken pipes
See the blockage table
Instrument + position error turn IAS into CAS. Compressibility turns CAS into EAS. Density turns EAS into TAS.
IAS to CAS
Instrument and position error
Instrument error: manufacturing imperfections and wear; found on the ground against a datum instrument
Position (pressure) error: mainly wrong static pressure at the vent; found in flight test, varies with speed and flap
Often combined on a single P and I correction card kept next to the ASI
IAS ± P and I correction = CAS; in airliners the ADC does it automatically
Manoeuvre-induced error: transient errors and lag when the angle of attack changes
Compressibility error
Why the ASI over-reads at height
At speed the air is compressed in the pitot: Pt is higher than ½ρV² predicts
The calibration allows for this at MSL ISA only; at altitude the effect is larger than allowed for
So the ASI over-reads: IAS and CAS are too high and EAS = CAS − correction
Grows with speed and altitude: CAS 300 kt needs about 3 kt at 10 000 ft, 15 kt at 30 000 ft
Can exceed 20 kt near Mach 1; small enough to ignore below about 300 kt TAS
Compressibility in numbers
How much to subtract from CAS
CAS
10 000 ft
20 000 ft
30 000 ft
40 000 ft
250 kt
−2 kt
−5 kt
−9 kt
−16 kt
300 kt
−3 kt
−8 kt
−15 kt
−25 kt
350 kt
−5 kt
−12 kt
−22 kt
above M 0.98
Order of correction: IAS → CAS (P and I) → EAS (compressibility, subtract) → TAS (density)
At MSL ISA there is no correction: CAS = EAS
Density error
TAS rises with altitude at constant CAS
Higher up the air is thinner: the same dynamic pressure needs a higher TAS
Climbing at constant CAS, TAS increases, roughly 1.75 % per 1000 ft
Example: CAS 120 kt at 8000 ft → TAS ≈ 120 + 16.8 ≈ 137 kt (exact ISA ≈ 135 kt)
Exact: TAS = EAS × √(ρ₀/ρ) = EAS ÷ √σ (σ = relative density)
ISA, CAS 250 kt: TAS ≈ 290 kt at 10 000 ft, ≈ 410 kt at 30 000 ft (ignoring compressibility)
Altitude and temperature
How TAS and CAS relate
Situation
Density
Result
Climb at constant CAS
Falls
TAS increases
Climb at constant TAS
Falls
CAS decreases
Same CAS and altitude, warmer than ISA
Lower
TAS higher
Same CAS and altitude, colder than ISA
Higher
TAS lower
Same CAS, higher pressure (lower pressure alt)
Higher
TAS lower
CAS 150 kt at 8000 ft (rule of thumb)
—
TAS ≈ 150 × 1.14 = 171 kt
Thinner air (high, hot, low pressure) → TAS greater than CAS.
Worked examples
Finding TAS
Problem
Working
TAS
CAS 120 kt, 6000 ft (rule of thumb)
120 + 1.75 % × 6 × 120 = 120 + 12.6
≈ 133 kt (exact ISA 131)
CAS 200 kt, FL100, ISA
σ ≈ 0.74; TAS = 200 ÷ √0.74
≈ 233 kt
Same CAS and level, ISA −15 °C
Colder → denser → less TAS for the same q
≈ 226 kt
CAS 250 kt, FL350, ISA +5 °C
Mach ≈ 0.74; LSS = 38.94 √T
≈ 432 kt
TAS 200 kt, 20 000 ft ISA: what does the ASI show?
EAS = TAS × √σ = 200 × 0.73
EAS ≈ 146 kt (CAS ≈ 147 kt)
Same CAS: warmer or higher → more TAS; colder or lower → less TAS.
Light aircraft
The TAS ring
Some light-aircraft ASIs have a rotating TAS scale inside the IAS scale
The pilot sets outside air temperature against pressure altitude in a small window
The same pointer then reads IAS on the outer scale and approximate TAS on the inner ring
Rough check: TAS ≈ CAS + 1.75 % per 1000 ft
Ignores compressibility: fine for light-aircraft speeds
Markings
Colour arcs on the ASI
White arc: flap operating range, VSO (bottom) to VFE (top)
Green arc: normal operating range, VS1 (bottom) to VNO (top)
Yellow arc: caution range, VNO to VNE, smooth air only
Red line: VNE, never exceed
Light twins add a blue line (VYSE) and a red radial (VMCA)
Marked in IAS, stall speeds at maximum weight
V-speeds
The speeds behind the markings
Speed
Meaning
On the dial
VSO
Stall speed / minimum steady flight speed in the landing configuration
Bottom of white
VS1
Stall speed in a specified (usually clean) configuration
Bottom of green
VFE
Maximum speed with flaps extended
Top of white
VNO
Maximum structural cruising speed (normal operating limit)
Top of green
VNE
Never exceed speed
Red line
VLO / VLE
Max speed to operate the gear (up or down) / to fly with gear extended
Placard, not arc
VYSE / VMCA
Best rate of climb one engine out / minimum control speed (max weight)
Blue line / red radial
Glass cockpit
The electronic speed tape
A vertical moving tape passes behind a fixed window with a digital readout of IAS
A trend vector shows the speed expected in about 10 s at the present acceleration
Barber pole at the top shows VMO/MMO; low-speed bands show the stall margin
Bugs mark selected and reference speeds; Mach shown below the tape
Fed by the ADC, so IAS → CAS corrections are already applied
Jet transport
Maximum allowable airspeed indicator
An ASI with a second, red-and-white "barber's pole" pointer showing the current limit speed
Limit is VMO (an IAS) low down and MMO (a Mach number) higher up
Below the crossover altitude the pole stays at VMO; above it the pole moves down as the IAS equivalent of MMO falls
Driven by an extra altitude (aneroid) capsule sensing static pressure, or by the ADC
An overspeed warning sounds if IAS reaches the pole
Blockage in action
Pitot and drain blocked in a climb
Ice closes the pitot inlet and the drain: the pitot pressure is trapped
In level flight the reading simply freezes; a slow leak makes IAS gradually decrease
In a climb, static falls while the trapped pitot does not: the difference grows and the ASI over-reads
In a descent it under-reads: the ASI behaves like an altimeter
Altimeter and VSI (static only) are unaffected
Blockages and leaks
When the ASI misleads
Fault
ASI in a climb
ASI in a descent
Pitot blocked, drain open
Falls to zero
Falls to zero
Pitot and drain blocked, level flight
Frozen (slow leak: decreases)
—
Pitot and drain blocked
Over-reads (acts as altimeter)
Under-reads
Static blocked
Under-reads
Over-reads (stall risk)
Pitot and static blocked
Frozen
Frozen
Static head (not vent) fitted
More exposed to icing: more likely to block
Level flight at constant speed hides a blockage: the reading only goes wrong when height or speed changes.
Leaks and alternate static
When the pipes are not sealed
Fault
Pressure reaching the ASI
ASI
Pitot line leak (unpressurised aircraft)
Pitot pressure lost to the lower cabin pressure
Under-reads
Static line leak, unpressurised cabin
Static replaced by cabin pressure, lower than static
Over-reads
Static line leak, pressurised cabin
Static replaced by cabin pressure, higher than static
Under-reads
Alternate static from the cabin (unpressurised)
Lower than static (suction)
Over-reads
Alternate static outside the hull
Extra position error; turbulence usually raises it
Usually under-reads
Rule: static too high → ASI under-reads; static too low → ASI over-reads. Pitot too low → under-reads.
Serviceability
Checks before and during flight
Pressure head covers and static vent plugs removed and stowed on board
Pitot tubes, static holes and vents free of obstructions such as insects
Pitot heater operative (if fitted)
Dial glass clean and undamaged; pointer at zero (or the stop) before engine start
ASI shows airspeed in the correct sense shortly after starting the take-off run
In flight, cross-check both ASIs and the standby; compare with attitude and power
Exam traps
Points that catch people out
ASI calibration: ISA at MSL (1.225 kg/m³), not "ISA" in general, not 1013.25 g/m³
Full error list: instrument, position, manoeuvre-induced, compressibility, density (no "temperature" or "barometric" error)
Compressibility: calibrated out at MSL; over-reads when density is lower and TAS exceeds about 300 kt
Same CAS and altitude, colder air → lower TAS; warmer → higher
Pitot (and drain) blocked in a climb: ASI increases whatever the real speed