Arrow keys, the buttons or swipe to move between pages. The Lab is below the e-book.
Instruments · Chapter 5
The Pressure Altimeter A barometer that reads in feet: principle, calibration, simple, sensitive and servo types, subscale settings, definitions, errors, density altitude and pre-flight checks.
0 1 2 3 4 5 6 7 8 9 ALT 1013 100 FEET
This chapter is the pressure altimeter. Like the airspeed indicator, it does not measure what it displays. It is a barometer: it measures the static pressure around the aircraft and converts it into a height using the standard atmosphere. As long as the real atmosphere matches the assumptions and the right pressure is set on the subscale, the reading is the height you want. When the day is colder than standard, or the pressure has changed since you set the subscale, the reading can be wrong, and usually in the dangerous direction. We cover the principle and calibration, the simple, sensitive and servo-assisted altimeters and how they are read, the subscale settings and the definitions of height, altitude and flight level, all the errors with worked examples, blockages, density altitude and the pre-flight altimeter check.
Principle
Measuring height with pressure Pressure at a point = weight of the column of air above it: higher up, a shorter column, lower pressure So a barometer can be scaled in feet ; only static pressure is used The relation is not linear , and weather systems and temperature change it An aneroid capsule (evacuated, sealed) expands as pressure falls The scale assumes the ISA pressure-height relationship 1000 800 600 400 200 0 10k 20k 30k 40k static pressure (hPa) height (ft) 1013 hPa 697 hPa 466 hPa 301 hPa 188 hPa 1013 hPa STATIC 0 FT 10 000 20 000 30 000 40 000 0 FT HEIGHT 27 ft per hPa 37 ft per hPa 50 ft per hPa 70 ft per hPa 100 ft per hPa 27 ft per hPa aneroid capsule expands as P falls
The altimeter works because pressure falls as you go up. Each layer of air is pressed down by the weight of all the air above it, so the higher you are, the less air is above you and the lower the pressure. That means a barometer can be marked in feet instead of hectopascals. The relationship is not a straight line. Near sea level a change of one hectopascal corresponds to about twenty-seven feet. At twenty thousand feet the air is thinner and the same change is about fifty feet, and at forty thousand feet about a hundred feet. The sensing element is an aneroid capsule: a sealed, nearly evacuated metal box that expands as the outside pressure falls. The instrument case is connected to the static source only, and the dial is laid out to match the standard atmosphere.
Pressure and height
Not a straight line Pressure falls quickly near the surface and ever more slowly higher up Feet per hPa: about 27 ft at MSL , about 50 ft at 20 000 ft , about 100 ft or more at 40 000 ft So a given capsule movement means more height at altitude : small errors in pressure become big errors in feet The altimeter is made to show a linear scale of this non-linear relation (capsule design and a variable-magnification linkage) 1013.25 hPa = 29.92 inHg = 14.7 psi altitude (ft) pressure (hPa) 200 400 600 800 1013 10k 20k 30k 40k 27 ft / hPa ≈ 50 ft / hPa ≈ 110 ft / hPa ISA
Pressure does not fall evenly with height. Near the surface the air is dense and the pressure drops quickly as you climb; higher up the air is thinner and the pressure drops more slowly. The graph shows the standard atmosphere: the curve is flat near one thousand and thirteen hectopascals and becomes steeper and steeper. Put the other way round, one hectopascal is worth about twenty-seven feet at sea level, about fifty feet at twenty thousand feet and around a hundred feet or more at forty thousand. This matters for accuracy: a tiny pressure error, or a tiny friction in the mechanism, becomes a large height error high up. The altimeter must nevertheless show an evenly divided scale, so the capsules and a variable-magnification linkage are designed to turn this curve into a linear presentation. Remember the units: one thousand and thirteen point two five hectopascals is twenty-nine point nine two inches of mercury or fourteen point seven pounds per square inch.
Calibration
Calibrated to the ISA MSL: 1013.25 hPa, +15 °C , density 1225 g/m³ Temperature falls 6.5 °C/km (1.98 °C/1000 ft) to 11 km (36 090 ft) ; then −56.5 °C constant to 20 km (65 617 ft); then rises 1 °C/km to 32 km Laboratory calibration: known pressures applied, readings checked against ISA heights, rising and falling (to find lag) Residual errors within tolerance are listed as instrument error ; a bimetal in the linkage compensates for temperature With 1013.25 set, the altimeter reads pressure altitude Δh ≈ 27 ft per hPa near MSL
Because the real atmosphere varies, the altimeter is calibrated to a standard one, the International Standard Atmosphere. At mean sea level the pressure is one thousand and thirteen point two five hectopascals, the temperature fifteen degrees and the density twelve hundred and twenty-five grams per cubic metre. Temperature falls at six and a half degrees per kilometre, one point nine eight per thousand feet, up to eleven kilometres, thirty-six thousand and ninety feet; it then stays at minus fifty-six and a half up to twenty kilometres, and above that rises by one degree per kilometre. In the laboratory, known pressures are applied to the instrument and the readings checked against the matching ISA heights, both increasing and decreasing so that the lag can be measured. Discrepancies within tolerance are recorded as instrument error. A bimetal compensator in the linkage looks after the instrument's own temperature.
Construction
The simple altimeter One evacuated aneroid capsule ; case open to static pressure ; a leaf spring stops it collapsing Pressure falls → capsule expands → magnifying linkage turns a single pointer ; temperature-compensated A setting knob geared to the pointer: set zero before flight → height above the aerodrome; set elevation → approximate altitude Not sensitive: perhaps 20 000 ft per pointer revolution Large friction and lag: fit only for basic use 0 1 2 3 4 5 6 7 8 9 ALT 1000 FT evacuated capsule leaf spring Ps one pointer, no subscale
The simple altimeter has a single aneroid capsule from which most of the air has been removed. Left alone, the outside pressure would crush it flat, so a leaf spring holds it open. At any height the capsule settles where the spring force balances the outside pressure. When you climb, pressure falls, the spring pulls the capsule open a little, and a linkage turns the pointer to a higher reading. In a descent the opposite happens. The case is sealed except for the connection to the static source. The simple altimeter has one pointer, often no proper subscale, and a fair amount of friction in its linkage, so it is slow and not very accurate at height. Modern aircraft use the sensitive or servo altimeter instead.
Construction
The sensitive altimeter A bank of two or three capsules : more movement, enough to drive three pointers Pointers geared 100 : 10 : 1 : 1000, 10 000 and 100 000 ft per revolution Jewelled bearings reduce friction and lag; some have a knocking or vibrating device to overcome initial inertiaA variable datum mechanism with a subscale and knob sets the pressure datum (UK range 800–1050 hPa) Display: three pointers, or counter and pointer 0 1 2 3 4 5 6 7 8 9 ALT 1013 100 FEET three capsules bimetal subscale knob sets the datum
The sensitive altimeter is the standard mechanical altimeter. Instead of one capsule it has two or three stacked together, so the total movement for each foot of height is larger and the instrument can show small changes. The linkage runs in jewelled bearings to reduce friction, and some designs have a small vibrator to stop the mechanism sticking. A bimetallic compensator corrects for the effect of the instrument's own temperature on the capsules and linkage. Most importantly, it has a subscale: a knob that lets the pilot set a datum pressure, which appears in a small window. Turning the knob rotates the whole mechanism so that the altimeter reads zero at the chosen pressure level. The reading is shown with three pointers or with a counter and a single pointer.
Reading accuracy
Three pointers, one big risk The sensitive altimeter shows small changes well, but the three pointers are easily misread A misreading of 10 000 ft is easy in a fast descent with a high workload; accidents have followed Remedies tried: modified pointers, warnings, and a striped (hatched) sector that appears at low altitude (from about 16 000 ft on some designs) The real cure: the counter-pointer display Always cross-check the small pointer: which ten-thousand are you in? 0 1 2 3 4 5 6 7 8 9 1013 ALT striped sector: low altitude warning descending from 18 000 ft long: 100s broad: 1000s thin: 10 000s
The simple altimeter, with one pointer covering perhaps twenty thousand feet per revolution, is not sensitive. The three-pointer sensitive altimeter shows small changes of height beautifully, but it has a severe disadvantage: it is easy to misread. During a rapid descent in difficult conditions, with a high workload, a pilot can read nine thousand as nineteen thousand, or the other way round, and accidents have resulted. Various modifications were tried, including changes to the pointer shapes and warning systems. One is shown here: a striped, hatched sector that appears in a window on the dial as the aircraft descends through about sixteen thousand feet on some designs, warning that you are getting low. The greatest improvement, though, was to replace the three pointers with the counter-pointer display, which we will see shortly. With a three-pointer instrument, always check the smallest pointer first.
Variable datum
Setting the subscale Turning the knob changes the subscale and moves the pointers together The altimeter then shows height above the pressure level set ; e.g. aerodrome pressure 1005 set → height above the aerodrome Reduce the setting by 10 hPa → reading falls by about 270 ft : "decrease–decrease, increase–increase " The link is one way: a climb moves the pointers but never the subscale A change of surface pressure does not change the subscale either: only the pilot does 0 1 2 3 4 5 6 7 8 9 ALT 100 FEET 1013 1010 1006 1003 1003 1003 1003 1003 1003 1006 1010 1013 knob: subscale −10 hPa → reading −270 ft climb: pointers move, subscale stays reset knob
The variable datum mechanism lets the pilot choose the pressure level from which height is measured. Turning the knob turns the subscale in its window and, through gearing, the pointers. Watch the first phase of the animation: the subscale is wound down from one thousand and thirteen to one thousand and three, and the pointers drop by about two hundred and seventy feet, ten hectopascals at about twenty-seven feet each. Winding down decreases the reading, winding up increases it. When the knob stops, the altimeter shows height above the pressure level set. In the second phase the aircraft climbs: the pointers move, but the subscale does not. The connection only works one way. The subscale changes only when the pilot turns the knob; neither a change of height nor a change in the actual surface pressure moves it. That is exactly why barometric error exists.
Subscale settings
QFE, QNH and 1013 QFE : aerodrome pressure. Reads height above the aerodrome ; zero on the runwayQNH : aerodrome pressure reduced to MSL in ISA. Reads altitude ; aerodrome elevation on the runway1013.25 (standard, "QNE") : reads pressure altitude ; used for flight levelsRaising the subscale setting by 1 hPa raises the reading by about 27 ft ("increase-increase") QNH > QFE at an aerodrome above MSL QFE QNH 1013 0 1 2 3 4 5 6 7 8 9 ALT 100 FEET 985 1003 1013 QFE 985 QNH 1003 STD 1013 SUBSCALE 1500 FT 2000 FT 2270 FT READS height above aerodrome altitude above MSL pressure altitude MSL 1013 hPa level
The subscale lets you choose the datum. Set QFE, the actual pressure at the aerodrome, and the altimeter reads height above the aerodrome, zero on the runway. Set QNH, the aerodrome pressure reduced to mean sea level using the standard atmosphere, and it reads altitude above mean sea level, showing the aerodrome elevation when you are on the runway. Set the standard one thousand and thirteen point two five and it reads pressure altitude; divide by a hundred and you have the flight level. QNE is sometimes used for this standard setting, or for the reading on the runway with standard set. Remember the direction: winding the subscale up by one hectopascal raises the reading by about twenty-seven feet. Winding it down lowers the reading. For an aerodrome above sea level, QNH is always greater than QFE.
Height, altitude, flight level
One aircraft, three readings QFE set: height above the aerodrome (zero on the runway)QNH set: altitude above MSL (aerodrome elevation on the runway)1013 set: pressure altitude ; in hundreds of feet it is the flight level Example: elevation 540 ft, QFE 995 → QNH ≈ 995 + 540/27 = 1015 At 3000 ft altitude: height 2460 ft; 1013 level is ≈ 54 ft above MSL, so pressure altitude ≈ 2950 ft MSL altitude 3000 ft height 2460 ft elevation 540 ft QFE 995 → height QNH 1015 → altitude 1013 → FL29.5 (≈ 2950 ft)
Here is one aircraft described three ways. The aerodrome on the hill has an elevation of five hundred and forty feet, and the pressure there, the QFE, is nine nine five hectopascals. At twenty-seven feet per hectopascal, five hundred and forty feet is twenty hectopascals, so the QNH, the aerodrome pressure reduced to sea level in the standard atmosphere, is one thousand and fifteen. With QNH set, the altimeter reads altitude above mean sea level: three thousand feet. With QFE set it reads height above the aerodrome: two thousand four hundred and sixty feet. With one thousand and thirteen set it reads pressure altitude. Because the sea-level pressure is two hectopascals above standard, the one thousand and thirteen level lies about fifty-four feet above the sea, so the pressure altitude is about two thousand nine hundred and fifty feet, flight level twenty-nine and a half.
Definitions
Words the examiner uses Term Meaning Setting Height Vertical distance from a specified datum (also the size of an object) QFE: height above aerodrome Altitude Vertical distance from MSL QNH Elevation Height of a point on the ground above MSL Aerodrome reads it on QNH Pressure altitude Altimeter reading with 1013.25 set 1013 (QNE) Flight level Surface of constant pressure from 1013.25; reading in hundreds of feet (31 000 ft → FL310 , 6 500 ft → FL65 ) 1013 Absolute altitude Height above the surface directly below Radio altimeter Regional QNH Lowest QNH forecast for an area and period Altimeter under-reads : safe side
Cruising level is the generic term: a height, altitude or flight level, depending on the procedure in force.
These definitions turn up in every exam. Height is the vertical distance of a point from a specified datum, normally the aerodrome, so it goes with QFE; the word also means the vertical size of an object. Altitude is measured from mean sea level and goes with QNH. Elevation is the height of a point on the ground above sea level, which an altimeter on QNH shows on the runway. Pressure altitude is the reading with one thousand and thirteen point two five set. A flight level is a surface of constant pressure related to that standard datum, named in hundreds of feet: thirty-one thousand feet indicated is flight level three one zero, six thousand five hundred is flight level sixty-five. Absolute altitude is height above the ground directly below, usually from a radio altimeter. Regional QNH is the lowest QNH forecast for an area; set it and you read low, which is the safe side.
Vertical separation
Transition altitude, level and layer Transition altitude (TA) : at or below it, vertical position is an altitude on QNH Transition level (TL) : the lowest flight level available above the TATransition layer : the airspace between TA and TL; do not cruise in itClimbing : set 1013 when passing the TA Descending : set QNH when passing the TL Above TA everyone uses 1013, so aircraft stay correctly separated from each other TA 6000 ft (QNH) TL FL80 (1013) transition layer climb: set 1013 descent: set QNH QNH 1003 STD 1013 QNH 1003
Close to the ground you need to know your height above the terrain, so you fly altitudes with QNH set. Higher up, what matters is separation from other aircraft, so everybody sets the same standard pressure and flies flight levels; it does not matter that flight levels are not true heights, as long as everyone makes the same error. The transition altitude is the altitude at or below which you report altitude on QNH. The transition level is the lowest usable flight level above it, and the space between them is the transition layer. When climbing, change to one thousand and thirteen as you pass the transition altitude. When descending, change to QNH as you pass the transition level. In the layer, report as a flight level when climbing and as an altitude when descending.
Displays
Three-pointer and drum-pointer Three-pointer : long pointer 100s, short broad pointer 1000s, small pointer 10 000sNotorious for misreading by 10 000 ft (or 1000 ft); some have a striped low-altitude warning sector Counter-pointer (drum-pointer) : digital counter for the altitude, one pointer at 1000 ft per turn for the rateQuick to read and hard to misread; the usual servo altimeter display Glass cockpits: vertical altitude tape with a digital readout (often with metres) 0 1 2 3 4 5 6 7 8 9 ALT 1013 100 FEET 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 FEET three-pointer counter-pointer 11 500 FT 12 300 FT 11 500 FT
Altimeters display height in two main ways. The older three-pointer altimeter has a long thin pointer for hundreds of feet, a shorter broad pointer for thousands and a small pointer, often a triangle on the rim, for tens of thousands. It is compact, but under workload it is easy to misread by a thousand or even ten thousand feet, and accidents have resulted; some have a striped warning sector that shows at low altitude. The counter-pointer, or drum-pointer, altimeter shows the altitude on rotating number counters and keeps a single pointer making one revolution per thousand feet. The counters give an unambiguous value, and the pointer gives the clear sense of change of height that matters so much on an instrument approach. It is the normal display for servo altimeters. Glass cockpits use a vertical moving tape with a digital window, often with a metric readout as well.
Servo altimeter
Servo-assisted altimeter Small capsule movements are detected by an electromagnetic pick-off : a light I-bar near an AC-fed E-bar Movement unbalances the induced voltages → error signal → amplifier → servo motor Motor drives counters and pointer and, via a cam , re-aligns the E-bar until the signal is zero Capsules only move the I-bar: more accurate at height, much less lag , greater range Needs power: a warning flag shows on failure; an ADC can replace the capsules entirely 0 1 2 3 4 5 6 7 8 9 ALT 1013 100 FEET E-bar (AC coils) I-bar capsule amplifier motor error signal → motor error signal → motor
In the servo-assisted altimeter the capsules no longer have to drive the gears. They move only a very light soft-iron I-bar, which sits close to an E-shaped core, the E-bar. The middle limb of the E-bar carries a coil fed with alternating current and the outer limbs carry pick-off coils. When the I-bar is centred, the voltages in the two pick-off coils cancel. When the capsules move it, the balance is upset and an error signal appears. This is amplified and drives a servo motor, which turns the counters and pointer and, through a cam, moves the E-bar back into line with the I-bar, cancelling the signal. Because the capsules do almost no work, friction is tiny: the servo altimeter is more accurate, especially at height, and lag is much smaller. If power fails, a warning flag appears.
Servo altimeter in detail
The E-I bar pick-off AC is fed to the centre leg of the E-bar, setting up alternating fields in the outer legs A and B Coils A and B are wound 180° out of phase : with the I-bar centred their outputs cancel Pressure change → capsules tilt the I-bar → one gap closes, the other opens → imbalance = error signal Signal is amplified and rectified , drives the motor, which turns the display and, via the cam, the E-bar When the E-bar is realigned the signal stops: the display shows the correct height A B AC error signal amp → motor → pointers cam re-aligns E-bar E-bar I-bar capsules
Let us look closely at the pick-off of the servo altimeter. The E-bar is a laminated iron core shaped like a letter E. Alternating current is fed to a coil on its centre leg, which sets up alternating magnetic fields through the two outer legs, A and B. Each outer leg carries a coil, and the two are wound one hundred and eighty degrees out of phase. When the light I-bar, moved by the capsules, sits exactly equidistant from the legs, the voltages induced in A and B are equal and opposite and cancel: no signal. When the pressure changes, the capsules tilt the I-bar, closing the gap at one end and opening it at the other. The balance is lost and an error signal appears. It is amplified and rectified and drives the servo motor, which turns the counters and pointer and, through a cam, swings the E-bar back into line with the I-bar. The signal then dies away.
Accuracy and lag
How good is each type? Type Accuracy Lag Simple Poor; tolerance grows steeply with height Considerable Sensitive Better; error increases with altitude (friction) Lab test: rising vs falling readings within 150 ft Servo-assisted Error ≈ 1 hPa : ≈ 30 ft at MSL, 50 ft at 20 000 ft, 100 ft at 40 000 ft None appreciable below about 10 000 ft/min Certification (large aircraft) At MSL: ±30 ft per 100 kt CAS — ADC-driven Position error corrected automatically As servo
Exact tolerance tables vary with type and are not to be learnt; the trends are.
How accurate is each kind of altimeter? The simple altimeter is poor and gets much worse with height. The sensitive altimeter is better, but its error grows with altitude, because the capsule movement for each foot is so small up there that friction in the linkage matters more. In the laboratory its lag is checked by comparing rising and falling readings, which should agree within about a hundred and fifty feet. The servo-assisted altimeter is the best: its normal instrument error is roughly equivalent to one hectopascal, about thirty feet at sea level, fifty at twenty thousand and a hundred at forty thousand, and it shows no appreciable lag unless the rate of change of height exceeds about ten thousand feet per minute. The large-aircraft certification standard at sea level is plus or minus thirty feet per hundred knots. Learn the trends rather than the exact figures.
Errors
Altimeter errors at a glance Error Cause Effect Time lag Linkage friction and capsule inertia Under-reads climbing, over-reads descending Instrument Manufacture, friction; hysteresis after long periods at one level Correction card; grows with height Position (pressure) Static vent not sensing true static; grows at high Mach Corrected by ADC Manoeuvre-induced Transient pressure at the static vent in pitch changes; pipeline delays Brief Barometric Pressure at the datum differs from the subscale setting ~27–30 ft per hPa Temperature Air colder or warmer than ISA ≈ 4 % per 10 °C Blockage Static source blocked Altimeter freezes
Here are the altimeter errors. Instrument error comes from manufacturing limits and friction, and it includes hysteresis: after the capsule has spent a long time at one height its metal takes a slight set, so it responds unevenly when the height changes. Position error is the static vent not sensing true static pressure, and it grows at high Mach numbers; air data computers correct it. Time lag means the pointer trails the real height, so the altimeter under-reads in a climb and over-reads in a descent. Barometric error is the difference between the pressure set on the subscale and the real pressure, about twenty-seven feet per hectopascal. Temperature error comes from non-standard air temperature, about four percent per ten degrees. A blocked static source freezes the altimeter, and rapid manoeuvres give brief errors.
Time lag
The pointer trails the aircraft The capsules and linkage cannot respond instantly, so the reading lags behind the real height In a climb the altimeter under-reads ; in a descent it over-reads Worst when the height change is rapid and prolonged Caused mainly by friction in the linkage; jewelled bearings and vibrators reduce it Servo altimeters: negligible below about 10 000 ft/min time altitude climb: under-reads descent: over-reads true indicated
Time lag is the simplest error to picture. The capsules have to expand, and the linkage has to move against friction, before the pointer can follow a change of pressure, so the indication trails behind the true height. Watch the two lines. In the climb the orange indicated line is below the blue true line: the altimeter under-reads. When the aircraft levels off, the indication catches up. In the descent the indicated line stays above the true one: the altimeter over-reads, which is the dangerous case, because you are lower than you think as you approach the ground. The lag is greatest when the change of height is fast and goes on for a long time. Jewelled bearings and vibrators reduce friction in the sensitive altimeter, and in the servo altimeter the lag is negligible unless the rate exceeds about ten thousand feet per minute.
Barometric error
High to low, look out below The altimeter follows a constant pressure surface matching the subscale setting Flying from high towards low pressure without resetting, the aircraft descends while the reading stays the same So the altimeter over-reads : you are lower than indicated Size ≈ 27 ft per hPa (30 ft as a rule of thumb low down) Cure: keep the current regional or aerodrome QNH set H L 0 1 2 3 4 5 6 7 8 9 ALT 1013 100 FEET 3000 FT 2700 FT 2400 FT TRUE HEIGHT high to low: look out below
Barometric error happens when the pressure at the datum is no longer what is set on the subscale. Suppose you set QNH at departure and fly towards an area of lower pressure. The pressure surfaces slope down from high to low. Holding a constant indicated altitude means holding a constant pressure, so the aircraft quietly follows the sloping surface downwards. The altimeter still shows the same figure, but the aircraft is lower than indicated: the altimeter over-reads. Hence the rhyme: high to low, look out below. The size is about twenty-seven feet for every hectopascal of difference, thirty feet as a rough rule low down. Going from low to high pressure, the aircraft climbs and the altimeter under-reads, which is safe but still wrong. Keep the current QNH set.
Barometric error worked
A to B without resetting Leave A with QNH 1020 set; fly to B (QNH 1002 ) at an indicated 8000 ft , subscale unchanged The altimeter shows height above the 1020 hPa level , wherever that is At B the 1020 level is 18 hPa below MSL : 18 × 30 = 540 ft below sea level True altitude at B = 8000 − 540 = 7460 ft : the altimeter over-reads Draw a datum diagram : pressure falls with height; the altimeter reads above the datum set MSL 1020 hPa level A: QNH 1020 B: QNH 1002 true 8000 ft true 7460 ft 540 ft IND 8000 FT 18 hPa × 30 ft = 540 ft lower (vertical scale exaggerated)
Here is a full worked example. You leave A, where the QNH is one thousand and twenty, with that value set, and fly to B, where the QNH is one thousand and two, holding an indicated eight thousand feet and never touching the subscale. The altimeter always shows height above the pressure level set on the subscale, here the one thousand and twenty hectopascal level. At A that level is at sea level. At B the sea-level pressure is only one thousand and two, so the one thousand and twenty level must lie below the sea, by eighteen hectopascals, which at thirty feet each is five hundred and forty feet. The aircraft is still eight thousand feet above that level, so its true altitude is seven thousand four hundred and sixty feet. The altimeter over-reads: high to low, look out below. Sketch a datum diagram like this one whenever a question involves two pressures.
Temperature error
Colder than ISA: lower than indicated In cold air the column is denser and shorter: pressure levels sit closer to the ground At a given indicated altitude you are lower than indicated : the altimeter over-reads In warm air the opposite: you are higher than indicated Rule: 4 % of the height above the datum per 10 °C ISA deviation Most dangerous in cold weather over high ground ; add a cold-temperature correction to minimum altitudes ISA ISA ISA −30 °C ISA 6000 FT INDICATED 6000 FT 5280 FT 6000 FT TRUE 4 % per 10 °C colder: lower than shown
Temperature error comes from the density of the air column. Cold air is denser, so a given pressure drop happens over a shorter distance and all the pressure levels sit closer to the ground. An aircraft flying at three thousand feet indicated in cold air is following a pressure level that is lower than three thousand feet: the altimeter over-reads and you are lower than you think. In warmer than standard air the levels are spread out and you are higher than indicated. A useful rule is four percent of the height above the pressure datum for every ten degrees of deviation from ISA. The effect is worst in very cold weather over high ground, which is why minimum altitudes are corrected upwards in the cold. Again: high to low, or hot to cold, look out below.
Temperature error worked
Correcting for cold air Problem Working Answer Indicated 6000 ft on QNH, OAT −13 °C at that level ISA at 6000 ft ≈ +3 °C → ISA −16 → 6.4 % True ≈ 5620 ft (lower) Same, by the rough rule 4 ft per °C per 1000 ft 4 × 16 × 6 = 384 ft True ≈ 5620 ft Indicated 9000 ft, ISA +15 °C +6 % of 9000 True ≈ 9540 ft (higher) Decision height 300 ft, sea-level aerodrome at −30 °C 300 × 45 ÷ 243 ≈ 56 ft; round up Fly DH ≈ 360 ft indicated Cruise at FL310 in very cold air Correction too inaccurate above about 25 000 ft Not applied
Colder than ISA: true altitude lower than indicated, so add the correction to published minimum altitudes and heights.
Temperature error can be worked out with the navigation computer, or with simple rules. Suppose you are at an indicated six thousand feet on QNH and the outside air temperature is minus thirteen. The standard temperature there is about plus three, so the air is sixteen degrees colder than standard. At four per cent per ten degrees that is six point four per cent, about three hundred and eighty feet, so the true altitude is about five thousand six hundred and twenty. The rough rule of four feet per degree per thousand feet gives the same answer. In warm air the error reverses. For approaches, the published minimum heights are increased in cold weather: a three hundred foot decision height at a sea-level aerodrome at minus thirty needs about 56 feet added, rounded up. Above about twenty-five thousand feet the correction is considered too inaccurate to be worth making, because the temperatures in the column below are unknown.
Practice
Worked examples (1 hPa ≈ 30 ft) Situation Working Answer Flying FL60, QNH 993 1013 − 993 = 20 hPa × 30 = 600 ft lower Altitude ≈ 5400 ft On a 600 ft aerodrome, QNH 1003, 1013 set by mistake 10 hPa too high × 30 = +300 ft Reads 900 ft Aerodrome 900 ft, QNH 1020 900 ÷ 30 = 30 hPa QFE ≈ 990 hPa Indicated 8000 ft on QNH (near MSL), ISA −20 °C 8 % of 8000 = 640 ft True ≈ 7360 ft 5000 ft, 1013 set, actual QNH 1003, ISA −10 °C 5000 − 300 = 4700; −4 % ≈ −190 True ≈ 4510 ft
Always ask: is the setting too high or too low, is the air colder or warmer? Then check the sign.
Let us work some examples using thirty feet per hectopascal. At flight level sixty with a QNH of nine nine three, the standard pressure level is twenty hectopascals, about six hundred feet, below sea level pressure, so your altitude is about five thousand four hundred feet. On a six-hundred-foot aerodrome with QNH one thousand and three, setting one thousand and thirteen by mistake adds ten hectopascals, three hundred feet, so the altimeter reads nine hundred. For a nine-hundred-foot aerodrome with QNH one thousand and twenty, QFE is thirty hectopascals lower, nine nine zero. Twenty degrees colder than ISA is eight percent: eight thousand indicated is about seven thousand three hundred and sixty true. The last line combines both: correct the pressure first, then take four percent off. With twenty-seven feet per hectopascal the answers change a little.
Blockages and leaks
Static blocked or static line broken Static source blocked : the altimeter freezes at the blockage altitude Climbing it therefore under-reads ; descending it over-reads , the error growing with distance from the blockage height Static line fractured in a pressurised cabin : it shows the cabin altitude , lower than the aircraft’s Static line fractured in an unpressurised aircraft: cabin pressure is a little low, so it over-reads Use the alternate static source and its corrections blocked at 4000 ft 0 1 2 3 4 5 6 7 8 9 ALT 1013 100 FEET TRUE 4000 TRUE 5000 TRUE 6000 TRUE 6000 TRUE 5000 TRUE 4000 TRUE 3000 TRUE 2700 climbing: frozen reading under-reads descending: frozen reading over-reads static blocked
If the static source becomes blocked, the altimeter has no way of sensing any further change of pressure, so it stays at the altitude at which the blockage happened, whatever the aircraft does. In the animation the vent ices at four thousand feet. As the aircraft climbs, the altimeter still shows four thousand, so it under-reads. When the aircraft descends below four thousand, it over-reads, and the error grows the further the aircraft moves from the blockage height. That descent case is the dangerous one. Leaks behave differently. If the static line breaks inside a pressurised cabin, the altimeter senses cabin pressure and shows the cabin altitude, much lower than the aircraft's real altitude. If it breaks in an unpressurised aircraft, the cabin pressure is slightly below ambient because of aerodynamic suction, so the altimeter over-reads. Select the alternate static source and apply its corrections.
Density altitude
Hot and high Density altitude : the altitude in the ISA at which the actual density would occurEquivalently: the ISA altitude matching the actual pressure and temperature ; it governs engine and aircraft performance Exam rule: DA = PA + 120 × ISA deviation (ft, °C) Aerodrome PA 4000 ft at +32 °C: ISA there ≈ +7 °C → ISA +25 → DA ≈ 4000 + 3000 = 7000 ft Same aerodrome at −13 °C: ISA −20 → DA ≈ 4000 − 2400 = 1600 ft MSL aerodrome 4000 ft +32 °C (ISA +25) −13 °C (ISA −20) DA 7000 ft DA 1600 ft DA = PA + 120 × ISA deviation
Density altitude is the altitude in the standard atmosphere at which the actual air density would be found. Since density depends on pressure and temperature, it is also the standard altitude that matches the actual pressure and temperature together. It does not appear on any altimeter, but it is what the engines and wings feel, so it governs take-off and climb performance. For the exam, use the rule: density altitude equals pressure altitude plus one hundred and twenty feet for every degree of ISA deviation. Take an aerodrome at a pressure altitude of four thousand feet on a day of plus thirty-two. The standard temperature there is about plus seven, so the day is ISA plus twenty-five, and the density altitude is about seven thousand feet: the aircraft performs as if it were three thousand feet higher. On a cold day of minus thirteen it is ISA minus twenty, and the density altitude drops to about sixteen hundred feet.
Pre-flight altimeter check
Finding the instrument error on the ground Done at a known point, normally the apron , whose elevation is published Work out what the altimeter should read, allowing for the apron and the instrument’s height above it Example: aerodrome 320 ft, apron 305 ft, altimeter 15 ft above the apron, QFE set Expected: (305 − 320) + 15 = 0 ft ; actual reading +25 ft Instrument error +25 ft : the altimeter over-reads apron 305 ft aerodrome 320 ft QFE datum 15 ft 0 1 2 3 4 5 6 7 8 9 ALT QFE 100 FEET should read 0, reads +25 altimeter 15 ft above apron = at aerodrome level
Before flight the altimeter is checked at a point of known elevation, normally the apron, whose elevation is published. The trick is to work out what the instrument should read. In this example the aerodrome elevation, the QFE datum, is three hundred and twenty feet, the apron is at three hundred and five, and the altimeter sits fifteen feet above the apron in the cockpit. With QFE set, the apron is fifteen feet below the datum, so an altimeter on the apron surface would read minus fifteen; but the instrument is fifteen feet up, so it should read exactly zero. It actually reads plus twenty-five, so it is over-reading by twenty-five feet: an instrument error of plus twenty-five. With QNH set the same method applies, comparing the reading with the apron elevation plus the height of the instrument.
Exam traps
Points that catch people out Errors list: instrument, position, manoeuvre-induced, temperature, barometric, lag (no density or compressibility) Low → high pressure: altimeter under-reads ; high → low: over-reads (look out below) Static blocked on take-off with QNH set: altimeter keeps reading aerodrome elevation QFE on the ground reads zero ; QNH reads elevation ; switching QFE → 1013 adds (1013 − QFE) × 30 ft Regional QNH makes the altimeter under-read (safe side); lag under-reads climbing Climb: set 1013 at the TA ; descent: QNH at the TL ; DA = PA + 120 × ISA dev
Here are the traps. The altimeter's error list is instrument, position, manoeuvre-induced, temperature, barometric and lag; density and compressibility belong to the airspeed indicator. Flying from low to high pressure the altimeter under-reads; from high to low it over-reads. If both static vents are iced on the runway with QNH set, the altimeter goes on reading the aerodrome elevation after take-off. On the ground QFE reads zero and QNH reads the elevation, and when you change from QFE to standard, add thirty feet for every hectopascal that one thousand and thirteen exceeds the QFE. Regional QNH, the lowest forecast value, makes the altimeter under-read, which is the safe side. Lag makes it under-read in the climb. Finally the transition rules, and density altitude by the hundred-and-twenty rule.
Summary
What to take into the exam Aneroid capsules on static ; ISA calibrated; 27 ft/hPa at MSL, ≈50 at 20 000 ft, ≈100 at 40 000 ft Simple (one capsule, one pointer) → sensitive (2–3 capsules, 100:10:1, jewels, subscale) → servo (E-I bar, less lag) QFE → height, QNH → altitude, 1013 → pressure altitude / FL; subscale only moves when you turn itErrors: lag, instrument, position, manoeuvre, barometric (30 ft/hPa), temperature (4 %/10 °C); high/cold → low: look out below Static blocked: frozen ; broken line in pressurised cabin: reads cabin altitude DA = PA + 120 × ISA dev; pre-flight check: expected vs actual reading = instrument error
To sum up. The altimeter is an aneroid barometer on static pressure, calibrated to the standard atmosphere; one hectopascal is about twenty-seven feet at sea level and more higher up. The simple altimeter has one capsule and one pointer; the sensitive altimeter has two or three capsules, pointers geared one hundred to ten to one, jewelled bearings and a subscale; the servo altimeter uses an E-I bar pick-off and a motor, so it is more accurate and lags less. QFE gives height, QNH altitude and standard pressure gives flight levels, and the subscale never moves by itself. Know every error and its sign, especially barometric and temperature error. A blocked static freezes the altimeter. Density altitude is pressure altitude plus one hundred and twenty feet per degree of ISA deviation, and the pre-flight check finds the instrument error.