Automatic landing: objectives and equipment, fail-passive and fail-operational systems, LAND 2 and LAND 3, the sequence from approach mode to roll-out, go-around, weather minima and alert height.
Exclusive study material prepared by eatpl.in
Arrow keys, the buttons or swipe to move between pages. The Lab is below the e-book.
Instruments · Chapter 28
Autoland
Two or three autopilots, two radio altimeters and a Category III ILS: how an aircraft lands itself in fog.
Introduction
Why landing is the hardest task
All three axes and the speed must be controlled at the same time, close to the ground
Align with the centreline; reduce the sink rate to about 2 ft/s before touchdown
Reduce speed from about 1.3 Vs to 1.15 Vs by progressively reducing power
Level the wings and yaw to remove drift (de-crab) just before touchdown
An autoland must guide and control better than a pilot; an auto-approach hands over at DH
The autoland system
What an autoland system must achieve
Not disturb the flight path as a result of an active malfunction
Have adequate authority for accurate control along the required path
Warn the crew of a passive failure
Allow the manoeuvre to be completed after an active or a passive failure (fail-operational systems)
Active failure: the system does something wrong (e.g. a runaway); passive failure: it simply stops doing anything
The autoland system
Equipment needed for an automatic landing
At least two independent autopilots able to follow the ILS
Two independent radio altimeters for accurate height above the ground
A Category III ILS installation at the airport
A third autopilot (or duplicate monitoring) for fail-operational capability
Plus the crew qualification, aircraft certification and airport procedures for low-visibility operations
Autoland status
Fail-passive and fail-operational
Fail-passive (fail-soft): survives a failure without danger or a large path deviation, but can no longer autoland
Fail-passive needs at least two autopilots
Fail-operational (fail-active): survives a failure with no loss of performance; the autoland is completed
Fail-operational needs three autopilots, or two with duplicate monitoring of each channel
After one failure a fail-operational system becomes fail-passive
Autoland status
LAND 2 and LAND 3
LAND 3: triple redundancy of power sources, computers, sensors and servos: fail-operational
LAND 2: dual redundancy of computers, sensors and servos: fail-passive
Shown on an autoland status annunciator (on the PFD on modern aircraft)
A failure during the approach can downgrade LAND 3 to LAND 2, or remove autoland capability
Single-channel twins show 1 CH or SINGLE CH: no autoland
The sequence
The automatic landing at a glance
Cruise and early approach: single channel in pitch and roll
APP arms LOC and G/S and the other channels, which then monitor continuously
1500 ft: second A/P engages, FLARE armed, LAND 2/3; 800 ft: latest for the second A/P
Touchdown: nose lowered, roll-out; A/T disconnects; crew disengages the A/P to finish
Sensors
The radio altimeters
Vertical guidance to touchdown always uses radio altitude: true height above the ground
Effective once within range, typically below 2500 ft
Two independent radio altimeters, each feeding its own FCC; the Captain's also feeds the A/T
With one RA inoperative, do not use its FCC (or the A/T if affected) for approach and landing
So a single RA failure makes the autoland fail-passive at best
The sequence
Approach mode: arming the system
APP arms the AFDS to capture and track the localiser and glideslope; dual or single A/P (autoland only dual)
At least one VHF nav must be tuned to the ILS to select APP; for a dual approach the second too
APP is the only mode that allows both A/Ps to be engaged together; the second arms for later engagement
In fail-passive dual operation the controls follow the A/P commanding the least movement
LOC may be intercepted in HDG SEL, CWS R or LNAV; LOC or G/S may be captured first (normally LOC)
The sequence
Localiser and glideslope capture
LOC capture point varies with angle and closure but happens by ½ dot; FMA: VOR/LOC captured, 1 CH
G/S captured from below (preferred) or above at ⅖ dot; previous pitch mode drops out
With both captured the APP switch light goes out; the A/T N1 limit becomes GA
Now APP can be left only by TO/GA, by A/P off and both FDs off, or by re-tuning a nav receiver
An invalid ILS signal: A/Ps disengage and FD bars retract
The sequence
At 1500 ft and 800 ft
Below 1500 ft RA, with LOC and G/S captured, the second A/P couples to the controls
FLARE armed is annunciated; ROLLOUT arms if fitted; A/P go-around arms (not shown)
Status LAND 2 or LAND 3 is displayed
Pitch and roll can no longer be overridden into CWS: trying disengages the A/Ps
800 ft RA: the second A/P must be engaged by now, otherwise its engagement is inhibited
The sequence
400–330 ft: nose-up trim bias
The stabiliser is automatically trimmed an extra amount nose-up
The elevators neutralise and hold the resulting pitch-up moment
If the A/Ps disengage, forward column force may be needed to hold attitude
Purpose: aids the flare; after a fail-passive disconnect the nose rises, avoiding a hard contact and helping a go-around
If FLARE is not armed by about 350 ft RA, both A/Ps disengage
The sequence
Flare and retard
Flare starts at about 50 ft RA (45 ft gear altitude) and ends at touchdown
FLARE replaces G/S on the FMA; FD bars retract; the stabiliser is trimmed further nose-up
The flare path reduces the sink rate to about 2 ft/s at touchdown
The A/T starts retarding at about 27 ft RA so the thrust reaches idle at touchdown
Retard begins 2½ s after FLARE engages or at 27 ft, whichever is first
The sequence
Gear altitude
What matters for the flare is the height of the main wheels, not of the antenna
The RA antenna is under the forward fuselage; in the nose-up flare the wheels are lower than it
The computer calculates gear altitude from radio altitude, pitch attitude and the known geometry
That is why the flare starts at about 50 ft RA but 45 ft gear altitude
The sequence
Touchdown and roll-out
At about 5 ft gear altitude flare ends, LOC disengages, ROLLOUT engages (if fitted)
At about 1 ft the pitch attitude is reduced to 2°; at touchdown the elevators lower the nose and hold it down
The A/T disengages when reverse is selected, or about 2 s after touchdown anyway
Roll-out: steering proportional to localiser deviation, through rudder and nosewheel steering, or shown on a PVD
The AFCS stays engaged until the crew disengages it: that ends the autoland
Other features
Runway alignment (de-crab)
In a crosswind the aircraft approaches crabbed: heading into wind, track on the centreline
From 1500 ft the yaw channel computes the heading-track difference
Align mode arms with FLARE and engages below about 100 ft
The rudder yaws the nose onto the runway heading before touchdown: drift kick-off
Go-around
Automatic go-around
Needs dual A/P operation; arms when FLARE armed appears
Cannot engage before flare arm or after the A/P senses touchdown
TO/GA: thrust to reduced GA N1; 15° nose-up, then hold flap manoeuvring speed; roll holds the ground track
MCP speed blanks; speed cursors show the commanded speed
TO/GA after touchdown (before A/T disconnect): A/Ps disengage; A/T may give GA thrust; fly it manually
Go-around
Leaving the autopilot go-around mode
Situation
What happens
Below 400 ft RA
A/Ps must be disengaged to change pitch or roll from GA
Above 400 ft, roll mode changed first
Roll engages single-A/P (first A/P engaged); pitch stays dual GA
Pitch mode change
Not until enough nose-down trim has been added to reset the approach trim bias
Above 400 ft, pitch mode changed first
Single A/P pitch; second A/P disengages; roll goes to CWS R
Approaching selected altitude in GA
ALT ACQ then ALT HOLD, if stab trim suits single A/P; select ≥ 1000 ft above GA altitude
Stab trim unsuitable
ALT ACQ inhibited, A/P lights steady red, pitch stays GA
Clear the steady red lights by selecting a higher altitude or disengaging the A/Ps.
Approach mode
Single autopilot approach compared with dual
Feature
Dual A/P (autoland)
Single A/P
Status after LOC capture
1 CH, then LAND 2/3 below 1500 ft
1 CH for the whole approach
Flare and touchdown
Automatic
Not available; FLARE not annunciated
Stabiliser trim bias
Applied at 400–330 ft
Not applied
A/P go-around
Available after FLARE armed
Not available
Failure protection
Fail-passive or fail-operational
Fail-safe only
A single A/P ILS approach is flown exactly like a dual one until the pilot takes over by DH.
Annunciations
The FMA through an automatic landing
Stage
Roll
Pitch
Status
APP selected
HDG SEL · VOR/LOC
ALT HOLD · G/S
CMD
LOC captured
VOR/LOC
ALT HOLD · G/S
1 CH
G/S captured
VOR/LOC
G/S
1 CH
Below 1500 ft
VOR/LOC · ROLLOUT
G/S · FLARE
LAND 2 / LAND 3
50 ft
VOR/LOC · ROLLOUT
FLARE
LAND 2 / 3
Touchdown
ROLLOUT
FLARE (nose lowered)
LAND 2 / 3
Italic = armed (white, second line); upright = engaged (green, top line). A/T: SPEED, then RETARD at about 27 ft.
Weather minima
RVR, decision height and slant range
RVR: instrumentally derived range at which runway lights can be seen along the runway; passed to the pilot by ATC
DH: wheel height above runway elevation at which a go-around must start unless the visual reference is adequate
DH and RVR together are the weather minima, set by the authority for each aircraft type and airport
At DH the pilot looks down the approach path: the slant visual range can be less than the RVR
If the reference is not good enough at DH: go around, hold or divert
Weather minima
Categories of precision approach and landing
Category
Decision height
Visibility / RVR
CAT I
Not lower than 200 ft (60 m)
Visibility ≥ 800 m or RVR ≥ 550 m
CAT II
Below 200 ft, not lower than 100 ft
RVR ≥ 300 m
CAT IIIA
Below 100 ft (or none)
RVR ≥ 200 m
CAT IIIB
Below 50 ft, or no DH
RVR below 200 m, not less than 75 m
CAT IIIC
No DH
No RVR limit: to and along the runway and taxiways without external visual reference
Exam figures shown. Current ICAO Annex 6: CAT IIIA RVR ≥ 175 m; CAT IIIB RVR below 175 m, not less than 50 m. "All weather" still means crosswind and contamination limits apply.
Weather minima
Alert height
A specified radio height based on the aircraft and its fail-operational landing system
Failure of a required redundant system above AH: discontinue and go around (unless a higher DH can be used)
Failure below AH: ignored; the approach continues to an automatic landing
Used with fail-operational systems, often with no DH (CAT IIIB)
Exam traps
Points that catch people out
Fail-passive: no big deviation but no autoland (≥ 2 A/Ps); fail-operational: landing continues (≥ 3, or 2 + duplicate monitoring)
LAND 2 = fail-passive; LAND 3 = fail-operational
Losing one radio altimeter makes the autoland fail-passive at best