Aircraft Instruments · Chapter 27
How an autopilot works: purpose and fail-safe design, control loops, inner and outer loops, channels, actuators, interlocks, synchronisation, auto-trim, command modes, CWS and limitations.
Exclusive study material prepared by eatpl.in
Arrow keys, the buttons or swipe to move between pages. The Lab is below the e-book.
Instruments · Chapter 27
From a simple wing leveller to a dual-channel flight control system: loops, servos, trim, engagement, modes and limits.
Introduction
Safety
The basic autopilot
Control theory
The basic autopilot
The basic autopilot
Types of autopilot
Regulations
| Requirement | What it means |
|---|---|
| Single-pilot IFR | Autopilot with at least ALT HOLD and HDG modes, i.e. two-axis |
| Quick disengagement | Autopilot can be quickly and positively disconnected |
| Quick-release controls | On both control wheels, on the side opposite the throttles |
| Alignment indication | Shown to the pilot unless there is automatic synchronisation |
| Safe in malfunction | No hazardous loads or flight path deviations, normal or failed |
| Interlocks and modes | Positive interlocks and sequencing; current and armed modes indicated |
Attitude controls must move in the same plane and sense as the cockpit controls, with the direction marked.
Actuators
Engagement
Engagement
Engagement
Trim
Trim
Outer loop
| Channel | Typical outer loop modes |
|---|---|
| Roll | Heading hold, heading select, VOR intercept and track, LOC intercept and track, INS / LNAV |
| Pitch | Altitude hold, speed hold, Mach hold, vertical speed, VNAV |
| Autoland roll / pitch / yaw | Localiser · glideslope · runway align; then roll-out · flare · roll-out |
| Terms | Coupling = mode of operation; hold / lock = keep a value; capture = intercept a beam |
| Rule | Only one mode per channel at a time: one in roll, one in pitch |
A beam sensor switches automatically from intercept to track, e.g. ALT HOLD → G/S when the glideslope is reached.
Indications
Inputs
Worked example
Roll modes
Roll modes
Pitch modes
Pitch modes
| Mode | Pitch controls | Thrust (A/T) | Notes |
|---|---|---|---|
| IAS/MACH (SPD) | Speed: nose up to slow, down to speed up | as selected | Compares MCP speed with ADC speed |
| V/S | The selected vertical speed | SPEED mode holds MCP speed | Armed after a new altitude >100 ft away; thumbwheel to engage |
| LVL CHG climb | Holds MCP speed | N1 (climb thrust) | Previous speed kept, or present speed |
| LVL CHG descent | Holds MCP speed | RETARD to idle, then ARM | |
| VNAV | FMC profile: VNAV SPD or VNAV PTH | FMC SPD, N1, RETARD or ARM | MCP speed blanks; limited by MCP altitude |
VNAV path descent ends at G/S capture, another pitch mode, flaps beyond 15, or LNAV off without G/S capture.
Operation
| Phase | Roll | Pitch | Autothrottle |
|---|---|---|---|
| Take-off | TO/GA | TO/GA | Thrust ref (N1) |
| Climb | LNAV, HDG or VOR | LVL CHG, VNAV or V/S | Thrust ref, SPD or MACH |
| Cruise | LNAV, HDG or VOR | ALT HOLD or VNAV | SPD or MACH |
| Descent | LNAV, HDG or VOR | LVL CHG, VNAV or V/S | Thrust ref (idle), SPD or MACH |
| Approach | LNAV, HDG or LOC | ALT, G/S, FLARE | SPD |
| Landing | ROLL-OUT | (flare) | RETARD |
| Go-around | TO/GA | TO/GA | Thrust ref (GA) |
Other features
Limitations
Exam traps
Summary