Mass & Balance · Chapter 4
Moving the CG and Floor Loading How much load to move to bring the CG within limits, adding or removing load, floor and running-load limits, and the load and trim sheet.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Sometimes the CG ends up outside the limits, or close to them, and we have to fix it by moving, adding or removing load. In this lesson we'll learn one simple relationship that answers all of those questions, then look at the strength of the cabin and hold floors, and finish with how an airline's load and trim sheet does the same sums with index numbers.
Roadmap
What this lesson covers Moving mass One relationship answers it all
How much, how far Putting the CG where you need it
Adding or removing New moment over new mass
Floor strength Area load and running load
Trim sheet The same sums with index units
Practice Worked examples throughout
Chapter 4 · Moving the CG and Floor Loading
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here's the plan. We'll start with what happens when load is moved inside the aeroplane, and the one relationship that describes it. We'll use it to find how much load to move, or how far. Then adding and removing load, the strength limits of the floor, and finally how an airline's load and trim sheet does all this with index numbers instead of big moments.
Why move load?
When the CG is outside the limits The CG must stay inside the envelope If it is outside, or too close to a limit, change the loading Moving load changes the CG only : the point slides sideways Adding or removing load changes both
CG position → mass →
outside aft limit
after moving cargo forward
Same mass, CG moved: the point slides sideways
Chapter 4 · Moving the CG and Floor Loading
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Sometimes the loading puts the CG outside the envelope, or uncomfortably close to a limit. Then we must change the loading. If we move load from one place to another, the mass stays the same and only the CG changes, so on the envelope the point slides sideways back inside. If we add or remove load, both the mass and the CG change.
Moving mass
Moving load moves the CG Total mass stays the same The total moment changes Load moved aft : CG moves aft Load moved forward : CG moves forward 300 kg moved 8 m aft CG moves 0.04 m aft mass moved × distance = total mass × CG shift 300 × 8 = 60 000 × Δ → Δ = 2 400 ÷ 60 000 = 0.04 m
Chapter 4 · Moving the CG and Floor Loading
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
When cargo is moved from one hold to another, nothing is added or removed, so the total mass stays the same. But the cargo's arm changes, so the total moment changes, and so does the CG. Shift a container from the forward hold to the aft hold and the CG is moved aft. Shift it the other way and the CG comes forward.
The shift formula
Mass moved × distance = total mass × CG shift 300 kg moved 8 m aft CG moves 0.04 m aft mass moved × distance = total mass × CG shift 300 × 8 = 60 000 × Δ → Δ = 2 400 ÷ 60 000 = 0.04 m
Chapter 4 · Moving the CG and Floor Loading
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
That gives us the key relationship. The mass moved, times the distance it's moved, equals the total mass of the aeroplane, times the distance the CG moves. Here a three hundred kilogram box is moved eight metres aft in a sixty thousand kilogram aeroplane. Three hundred times eight is two thousand four hundred. Divide by sixty thousand and the CG moves four centimetres aft. Notice it's the total mass of the aeroplane on the right-hand side, not the mass of the box.
The shift formula
Which way does the CG go? Load moved forward → CG moves forward Load moved aft → CG moves aft
Chapter 4 · Moving the CG and Floor Loading
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The direction is easy to remember: the CG always follows the load. Move load forward and the CG moves forward. Move it aft and the CG moves aft. The formula gives you how far; the direction comes from which way the load went.
How much, how far
Rearranging the same formula You want Use Example (aeroplane 52 000 kg) CG shift Δ = m × d ÷ M 500 kg moved 10 m: Δ = 0.096 m Mass to move m = M × Δ ÷ d Move CG 0.15 m with holds 12 m apart: m = 650 kg Distance to move d = M × Δ ÷ m 400 kg, CG to move 0.06 m: d = 7.8 m
M is the total mass of the aeroplane, which does not change when load is moved.
Chapter 4 · Moving the CG and Floor Loading
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The same formula can be turned round to answer any question. To find the CG shift, multiply the mass moved by the distance and divide by the total mass. To find how much mass to move, multiply the total mass by the CG shift you need and divide by the distance between the holds. And to find how far to move a given mass, multiply the total mass by the shift and divide by that mass. Here, to move the CG of a fifty-two thousand kilogram aeroplane by fifteen centimetres, with holds twelve metres apart, you'd move six hundred and fifty kilograms.
How much, how far
Worked example: how much to move m = ? holds 12 m apart (centre to centre) Aeroplane 52 000 kg, CG 0.15 m too far aft: how much cargo to move forward? m = M × Δ ÷ d = 52 000 × 0.15 ÷ 12 = 650 kg from the aft hold to the forward hold
Chapter 4 · Moving the CG and Floor Loading
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let's work one through. A fifty-two thousand kilogram aeroplane has its CG fifteen centimetres too far aft. The holds are twelve metres apart, centre to centre. The mass to move is fifty-two thousand times zero point one five, divided by twelve: six hundred and fifty kilograms, taken from the aft hold and put in the forward hold.
Adding or removing
When the total mass changes Adding or removing changes the total mass New CG = new total moment ÷ new total mass Shortcut: Δ = m × (arm − old CG) ÷ new mass A mass added at the CG does not move it Removing: use −m
Before: 60 000 kg, CG 18.00 m
Moment = 60 000 × 18.00 1 080 000
Add 1 200 kg at 24.00 m + 28 800
New mass 61 200 kg
New moment 1 108 800
New CG = 1 108 800 ÷ 61 200 18.12 m
Shortcut
Δ = added mass × (its arm − old CG) ÷ new total mass
= 1 200 × (24 − 18) ÷ 61 200 = 0.12 m aft
Removing mass: use − m and the reduced total mass.
Chapter 4 · Moving the CG and Floor Loading
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Adding or removing load is different, because the total mass changes too. The safe method is to work out the new total moment and divide by the new total mass. Here, adding twelve hundred kilograms at twenty-four metres to a sixty thousand kilogram aeroplane with its CG at eighteen metres gives a new CG of eighteen point one two. There's a shortcut: the added mass times its distance from the old CG, divided by the new total mass. And notice: a mass added exactly at the CG doesn't move it at all.
Adding or removing
Removing a mass −900 kg CG moves AFT Removing a mass forward of the CG moves the CG aft (and the reverse). New CG = new moment ÷ new mass.
Chapter 4 · Moving the CG and Floor Loading
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Removing load works the same way, with a minus sign. Take nine hundred kilograms out of the forward hold, which is ahead of the CG, and the CG moves aft, away from where the load was. The new CG is the new total moment divided by the new, smaller, total mass.
Floor strength
Area load and running load Area load : mass ÷ footprint area (kg/m²)Running load : mass ÷ length along the fuselage (kg/m)Both must be below the limits for that compartment A spreader plank enlarges the footprint Turning a long item lengthwise lowers the running load
800 kg
1.6 m along the fuselage
1.0 m wide
Area load = 800 ÷ (1.6 × 1.0) = 500 kg/m²
Running load = 800 ÷ 1.6 = 500 kg/m
Chapter 4 · Moving the CG and Floor Loading
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The floor has limits too. The area load is the mass divided by the footprint it stands on, in kilograms per square metre. The running load is the mass divided by the length it occupies along the fuselage, in kilograms per metre, because the floor beams run across the aeroplane. This eight hundred kilogram box on a footprint one point six metres long and one metre wide gives five hundred of each. If either exceeds the compartment's limit, spread the load with planks, or turn the item lengthwise.
Floor strength
Area load: spread it out Area load = mass ÷ footprint area (kg/m²)Small footprint → high area load A spreader plank enlarges the footprint Count the plank's own mass too
600 kg
footprint 0.5 × 0.5 m
2 400 kg/m²
600 kg
on a plank 1.5 × 1.0 m
400 kg/m²
Area load = mass ÷ footprint area
Limit here 600 kg/m²: the plank makes it acceptable.
(Include the plank's own mass in a real calculation.)
Chapter 4 · Moving the CG and Floor Loading
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Look at area load more closely. Six hundred kilograms standing on a footprint half a metre square presses down at two thousand four hundred kilograms per square metre, far above a limit of six hundred. Put the same item on a spreader plank one and a half metres by one metre and the area load drops to four hundred, which is acceptable. In a real calculation, remember to add the plank's own mass.
Floor strength
Running load: turn it lengthwise
floor beams run across the fuselage
1 000 kg
0.5 m → 2 000 kg/m
1 000 kg
2.5 m → 400 kg/m
Running load = mass ÷ length along the fuselage. Lengthwise is kinder to the floor.
Chapter 4 · Moving the CG and Floor Loading
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Running load is about how much mass sits on each metre of fuselage length, because the floor beams run across the aeroplane. A thousand kilograms occupying half a metre of length gives two thousand kilograms per metre. Turn a long item lengthwise so it covers two and a half metres, and the running load falls to four hundred kilograms per metre.
Load and trim sheet
What is an index?
Index = mass × (arm − reference arm) ÷ C + K
Reference arm a point near the CG range, so the moments stay small
Constant C scales millions of kg m down to tens
Offset K keeps every index a positive number
Example: 1 000 kg at 25 m, reference 18 m, C = 1 000, K = 50 → 1 000 × 7 ÷ 1 000 + 50 = 57
On the trim sheet each item already has its index change printed: you only add arrows.
Chapter 4 · Moving the CG and Floor Loading
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before the trim sheet itself, what is an index? It's a moment made small. Take the mass times its distance from a reference arm near the middle of the CG range, divide by a constant to bring millions down to tens, and add an offset so the answer is always positive. A thousand kilograms at twenty-five metres, with a reference of eighteen, a constant of a thousand and an offset of fifty, gives an index of fifty-seven.
Load and trim sheet
The same sums with index units
-30 -20 -10 0 10 20 30 40 50 60 70 80
Dry operating index
Cargo hold 1 (+600 kg)
Cabin rows 1–10 (+40 pax)
Cabin rows 20–30 (+60 pax)
Cargo hold 4 (+900 kg)
Zero fuel index → plot on the envelope
An index is a scaled moment about a reference point: small numbers instead of millions of kilogram-metres.
Chapter 4 · Moving the CG and Floor Loading
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Airlines don't add up moments in millions of kilogram-metres. Their load and trim sheet uses index units, which are moments scaled down and measured from a convenient reference point. You start at the dry operating index, then for each hold or cabin section you draw an arrow left or right by the amount printed for that load. Forward loads move the index left, aft loads move it right. Where you finish is the zero fuel index, which you plot on the envelope with the mass.
Moving m × d = M × Δ; total mass unchanged
Rearrange Find the shift, the mass or the distance
Adding/removing New moment ÷ new mass
At the CG A mass added there does not move the CG
Floor Area load kg/m², running load kg/m
Trim sheet Index arrows from the DOI to the ZF index
Chapter 4 · Moving the CG and Floor Loading
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. When load is moved, the mass moved times the distance equals the total mass times the CG shift, and the total mass doesn't change. Rearrange it to find the shift, the mass or the distance. When load is added or removed, divide the new moment by the new mass. Check the area and running loads against the floor limits, and remember the trim sheet does the same job with index units.