Meteorology · Chapter 17
Mountain Waves What happens to a strong, stable airflow after it crosses a ridge: lee waves, rotors, their clouds, the turbulence and downdraughts, and the altimeter traps.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter seventeen is about mountain waves. When a strong, steady wind blows across a mountain range in the right conditions, the air on the far side does not settle back smoothly. It oscillates up and down in a train of waves that can stretch a long way downwind and far above the summits. Those waves carry powerful up and down currents, some of the worst turbulence a pilot can meet, and traps for the altimeter. We will learn when they form, how to recognise them from their clouds, and how to fly near them safely.
Definition
Waves in the air downwind of high ground stable layer near ridge level Wind across the ridge increasing with height Cap cloud pours down the lee: föhn wall Lenticular clouds in the wave crests, stacked Rotor cloud under the first crest: worst turbulence wavelength ≈10 km waves may run 100–200 km downwind A mountain wave is an oscillation of the airflow on the lee side of high ground, set off by the high ground disturbing a strong horizontal flow.
Chapter 17 · Mountain Waves
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
A mountain wave, also called a lee wave or standing wave, is an oscillation of the airflow on the lee side of high ground. A strong wind blowing across a ridge is pushed up over the summit. If the air is stable, it does not want to stay displaced; it plunges down the lee slope, overshoots, rises again and keeps bouncing up and down in a train of waves that stay fixed in position relative to the mountain while the air blows through them. The waves can reach great heights and stretch a long way downwind. On the diagram you can see the cap cloud on the summit, the strong downdraught on the lee slope, lens-shaped lenticular clouds in the wave crests, and a rotor, a rolling eddy, under the first crest. The distance from one crest to the next, the wavelength, is typically about ten kilometres or more. Flying through such a system can be bumpy and dangerous, so we need to understand its pattern and scale.
When waves form
The wind and stability recipe Wind direction A definite flow across the ridge , within about 30° of perpendicular to it. A long, straight ridge works best.
Wind speed At least about 7 m/s (15 kt) for small hills and 15 m/s (30 kt) for large ranges, at ridge level.
Wind profile A deep, steady flow in much the same direction through a deep layer, increasing with height .
Stability A stable layer near and just above ridge level , with less stable air above it. The stable layer is what makes the air spring back.
Result Get all of these and a train of lee waves forms. Too little wind: no waves. Wind dropping or reversing aloft: violent rotors instead.
Seasons Steady, strong winds increasing with height and suitable stability make waves more frequent in winter .
Chapter 17 · Mountain Waves
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Mountain waves need a particular recipe. First the wind direction: there must be a definite flow across the ridge, within about thirty degrees of perpendicular to it, and a long straight ridge works best. Second the speed: at ridge level, at least about seven metres per second, roughly fifteen knots, for small hills, and about fifteen metres per second, roughly thirty knots, for large mountain ranges. Third the wind profile: a deep, steady flow in much the same direction through a deep layer, strengthening with height. And fourth the stability: a stable layer around ridge level, with less stable air above it. The stable layer is the spring that makes displaced air bounce back and oscillate, and the less stable air above lets the waves develop. When all of these come together, a train of lee waves forms. If the wind is too light there are no waves, and if the wind is strong low down but weakens or reverses higher up, you get violent rotors instead. Winter, with its steady strong winds, brings waves most often.
Up and down currents
Strong, extensive vertical currents Areas of rising and sinking air alternate; the sink is immediately downwind of the ridge, on the lee slope Over large mountains, vertical currents of 10–25 m/s (about 2000–5000 ft/min ) are not unusual Flying parallel to the ridge in a downdraught, you can keep losing height for the whole length of the ridge In an updraught you keep gaining height, which can take you through your level The downdraught on the lee side may exceed the aircraft’s climb performance So keep generous terrain clearance and approach a ridge at an angle so you can turn away Lee side sink of 2000–5000 ft/min Upwind side rising air may beat your climb rate wind →
Chapter 17 · Mountain Waves
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Within the wave system, areas of rising and sinking air alternate, and the sinking air is found immediately downwind of the ridge, pouring down the lee slope. These vertical currents can be strong and extensive. Over large mountains, ten to twenty-five metres per second, that is roughly two thousand to five thousand feet per minute, is not unusual. That may be more than your aircraft can climb. Because the waves line up parallel to the ridge, an aircraft flying along the lee side of a ridge and caught in the downdraught will keep losing height for the whole length of the ridge. Caught in an updraught it will keep gaining height instead, perhaps through its cleared level. So the golden rule is generous terrain clearance, and when you must cross a ridge, approach it at an angle, so that if you meet a strong downdraught you can turn away towards lower ground.
Seeing the wave
The clouds that mark mountain waves Wave clouds keep forming on the upwind side and dissolving on the downwind side , so they look stationary even in a strong wind. Waves may also give ST, SC, AS, CI and, very high up, nacreous clouds.
Cap cloud Sits on and over the summit . Strong winds may pour it down the lee slope as a föhn wall or “cloud fall”, like a waterfall. Severe turbulence in and near it.
Lenticular cloud Lens-shaped , in the wave crests , a few thousand feet above the summits, often stacked. Smooth edges: smooth wave. Ragged edges: turbulence.
Rotor (roll) cloud Ragged roll of cloud under the wave crest , strongest in the first wave , at or slightly above ridge level . The worst turbulence of all.
Chapter 17 · Mountain Waves
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
When the air is moist enough, mountain waves mark themselves with characteristic clouds. The cap cloud sits on and just above the summit. In strong winds it can be swept down the lee slope as a föhn wall, a cloud fall that looks like a waterfall, and there is severe turbulence in and near it. Lenticular clouds are smooth, lens-shaped clouds that form in the wave crests a few thousand feet above the summits, often several stacked one above another and repeated in each wave downstream. Smooth outlines suggest a smooth wave; ragged edges are a sign of turbulence. The rotor or roll cloud is a ragged roll of cloud under the crest of a wave, strongest in the first wave downwind, at or slightly above the level of the ridge. All these clouds keep forming on their upwind side and evaporating on their downwind side, so although the wind is blowing straight through them, they appear to stand still. Waves can also produce layers of stratus, stratocumulus, altostratus and cirrus, and in the stratosphere at high latitudes, nacreous clouds.
Turbulence
Smooth one moment, violent the next Flight in a wave can be smooth in places, but the change to turbulence is abrupt and without warning Worst turbulence is near rotor clouds , comparable to a violent thunderstorm ; gusts of 2–4 g are not unusual, and 7 g has been exceeded Severe turbulence also in the cap cloud and föhn wall If the wind is strong low down but weakens or reverses aloft , violent rotors stream downwind: rotor streaming Successive ridges can modify one another’s waves, sometimes producing violent turbulence How bumpy it feels depends on the aircraft’s size, speed and aerodynamics wind reverses aloft rotors stream downwind violent turbulence below ridge-top level
Chapter 17 · Mountain Waves
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Flying in a mountain wave is not always rough. In the smooth part of a wave, glider pilots ride the lift for hours. But because extra shear can develop in places, the change from smooth to turbulent air is extremely abrupt and comes with no warning. The worst turbulence is in and near the rotor clouds, comparable with a violent thunderstorm. There, both vertical and horizontal gusts occur, accelerations of two to four g are not unusual, and seven g has been exceeded. The cap cloud and the föhn wall also hold severe turbulence. A special case is rotor streaming. If the wind is strong at low levels but weakens or even reverses higher up, smooth waves do not form. Instead, violent rotors develop on the lee slope and stream away downwind, below the level of the ridge tops. Where there are several ridges in a row, the waves from one range are modified by the next, and that interference can also produce violent turbulence. How rough it feels depends on your aircraft’s size, speed and aerodynamic characteristics.
Altimeter traps
Why the altimeter cannot be trusted here Rapid up and down motion: the aneroid capsules cannot respond correctly and the instrument lags behind : lag (time-lag) error Strong wind speeds up over the ridge, so local pressure falls (Bernoulli): the altimeter over-reads Air colder than ISA : the altimeter also over-reads (you are lower than indicated); warmer: under-reads Rule of thumb: about 4% of height per 10 °C colder than ISA Worked example: indicated 12 000 ft , air ISA −20 ⇒ about 8% low ⇒ true height about 11 000 ft All errors point the same, dangerous way: lower than you think , close to the rocks indicated 12 000 ft true ≈11 000 ft less clearance than you think Lag capsules cannot keep up Bernoulli fast wind over the ridge lowers pressure Cold air ISA −20 °C ⇒ ≈8% low wind speeds up
Chapter 17 · Mountain Waves
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Over mountains, the altimeter can deceive you just when you need it most. In a wave the aircraft is carried rapidly up and down, and the aneroid capsules cannot follow such quick changes accurately; the instrument lags behind, which is called lag, or time-lag, error. Next, strong wind accelerating over a ridge lowers the local pressure, by Bernoulli’s principle, so the altimeter reads too high. And if the air is colder than standard, which is common over high ground in winter, the altimeter again over-reads: you are lower than indicated. A handy rule is about four per cent of your height for every ten degrees colder than ISA. For example, at an indicated twelve thousand feet in air that is ISA minus twenty, the error is about eight per cent, nine hundred and sixty feet, so your true height is only about eleven thousand feet. Notice that every one of these errors points the same dangerous way, making you lower than you think, close to the terrain. Do not rely on the altimeter alone for terrain clearance near mountains.
Extent and timing
How far, how high, and when Downwind extent Waves may extend 100–200 km downstream. Moderate to severe turbulence can be met 20–30 NM or more to the lee of a range.
Vertical extent Often far above the summits, sometimes well into the stratosphere , where they can set off CAT.
Wavelength Usually about 10 km or more ; a long range gives a train of waves and repeated lenticulars.
Evening waves After sunset , low levels become stable and winds ease: waves form to the lee of small and medium hills and last until morning heating. Little effect on big ranges.
Winter Steady winds strengthening with height and suitable stability make waves most frequent in winter .
Mountains and cloud Mountains increase cloud amount and depth , and waves increase the frequency and intensity of icing .
Size of aircraft Bumpiness felt depends on size, speed and design: a light aircraft is thrown about far more.
Gliders The smooth rising part of a wave gives sustained lift used by glider pilots to great heights.
Chapter 17 · Mountain Waves
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
How big is a wave system? It may extend a hundred to two hundred kilometres downstream of the range, and moderate to severe turbulence can be found twenty to thirty nautical miles or more on the lee side. Vertically, waves often reach far above the summits, sometimes well into the stratosphere, where they can break and give clear air turbulence. The wavelength is usually about ten kilometres or more, and a long ridge produces a whole train of waves. There is a daily cycle too. After sunset the lower layers cool and become stable, while the low-level wind eases, and waves form to the lee of small and medium hills; these evening waves last through the night until morning heating destroys the stable layer. Over big ranges this daily effect is small. Seasonally, winter brings the steady, strengthening winds and stability that waves need, so they are most frequent then. Mountains also increase the amount and depth of cloud, and waves increase the frequency and intensity of icing.
Hazards and safe practice
Flying near mountain waves Up and down currents Hard to hold altitude ; downdraughts may exceed climb performance; possible loss of control .
Turbulence Often severe and up to great heights ; can cause structural damage , worst in rotors.
Unexpected winds Large, sudden wind changes give unplanned loss or gain of height and track errors.
Icing More frequent and more intense icing in the wave clouds.
0 1 2 3 4 5 6 7 8 9
Altimeter errors Lag error, Bernoulli pressure drop and cold air all make the altimeter over-read .
Safe practice Expect lenticular and rotor clouds , strong lee-side downdraughts and turbulence well downwind. Keep a big height margin , cross ridges at an angle, avoid rotors and the lee side at low level.
Chapter 17 · Mountain Waves
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the hazards together. The strong up and down currents make it difficult to hold altitude, the downdraughts can exceed your climb performance, and in the worst cases control can be lost. The turbulence is often severe and reaches great heights, and in rotors it can cause structural damage. Large, unexpected winds give unplanned losses or gains of height and push you off track. Icing becomes more frequent and more intense in the wave clouds. And the pressure altimeter over-reads for several reasons at once. So when approaching an area where mountain waves have been reported, expect all of it: roll and lenticular clouds, intense updraughts and downdraughts on the lee side of the mountains, and moderate to severe turbulence perhaps twenty to thirty miles downwind. Keep a big height margin above the highest ground, cross ridges at an angle so you can turn away, and stay well clear of rotor clouds and the low-level lee side of the range.
Summary
What to take into the exam Definition Oscillations of the airflow on the lee side of high ground. Wavelength ≈10 km or more; 100–200 km downstream; may reach the stratosphere.
Wind Across the ridge within 30° of perpendicular. ≥7 m/s small hills, ≥15 m/s large ranges. Steady direction, increasing with height.
Stability Stable layer near ridge level, less stable air above.
Currents Sink just downwind of the ridge. 10–25 m/s over big mountains. Flying parallel to a ridge in sink: continuous height loss.
Clouds Cap (föhn wall), lenticular in crests (ragged = turbulent), rotor under the first crest at or just above ridge level.
Turbulence Worst near rotors: 2–4 g, at times 7 g. Abrupt onset. Rotor streaming if wind weakens or reverses aloft.
0 1 2 3 4 5 6 7 8 9
Altimeter Lag error, Bernoulli drop and cold air: altimeter over-reads. ≈4% per 10 °C below ISA.
Timing Evening waves on small and medium hills after sunset. Most frequent in winter.
Chapter 17 · Mountain Waves
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. A mountain wave is an oscillation of the airflow on the lee side of high ground, with a wavelength of about ten kilometres or more, reaching a hundred to two hundred kilometres downstream and sometimes into the stratosphere. It needs a wind across the ridge within thirty degrees of perpendicular, at least seven metres per second for small hills or fifteen for large ranges, steady in direction and increasing with height, with a stable layer near ridge level and less stable air above. The sink lies just downwind of the ridge, and over big mountains the vertical currents reach ten to twenty-five metres per second. Learn the clouds: the cap cloud and föhn wall, lenticulars in the crests, and the rotor under the first crest, where the turbulence is worst, two to four g and at times seven. The altimeter over-reads. And waves are commonest in winter, with evening waves after sunset over smaller hills.