Meteorology · Chapter 2
Atmospheric Pressure What pressure is, how it falls with height, how it is measured and mapped, and how the altimeter uses it.
L H 960 980 1000 1020 1040 RAIN CHANGE FAIR hPa ANEROID © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter two is about atmospheric pressure. Pressure is the quantity your altimeter actually measures, and it drives the wind, so it sits at the centre of meteorology. We look at what pressure is and the units it is measured in, how quickly it falls as you climb and why it falls faster in cold air, its small twice-daily rhythm, how upper-air charts use contours and thickness, the altimeter settings QFE, QNH, QFF and QNE with worked examples, the altimeter errors that catch pilots out, and finally the shapes that isobars make on a weather chart.
What pressure is
The weight of the air above you Air molecules strike every surface: static pressure acts equally in all directions; moving air adds dynamic (wind) pressure Pressure at a level = weight of the air column of unit area above it, so it falls with height Unit: the hectopascal (hPa) = millibar (mb); 1 bar = 1000 hPa = 100 000 N/m² 1013.25 hPa = 29.92 inHg = 760 mm of mercuryhPa to inches: multiply by 0.02953 (1013.25 × 0.02953 ≈ 29.92) Rapid pressure change in a fast descent makes the ears “pop” 10 000 ft 20 000 ft 30 000 ft 1013 hPa 697 hPa 466 hPa 301 hPa Weight of the column above 18 000 ft ≈ 500 hPa half the air is below thin air · low pressure
Chapter 2 · Atmospheric Pressure
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Air molecules are always moving and striking every surface around them. When the air is at rest, this push is the same in every direction, and we call it static, or barometric, pressure. When the air moves, it adds an extra push in the direction of the flow, called dynamic pressure. Another way to picture static pressure: at any level, it is the weight of the column of air, of unit area, standing above that level all the way to the top of the atmosphere. Climb, and there is less air above you, so pressure falls. ICAO uses the hectopascal, which is the same size as the millibar. Learn the equivalents: one thousand and thirteen point two five hectopascals equals twenty-nine point nine two inches, or seven hundred and sixty millimetres of mercury. To turn hectopascals into inches, multiply by zero point zero two nine five three.
Pressure and height
Pressure falls with height, ever more slowly Falls fast near the ground and more slowly higher up, because the air thins out Roughly halves by about 5.5–6 km (500 hPa near 18 000 ft); near vacuum by 100 km Height change for 1 hPa = 96 T ÷ p feet (T in kelvin, p in hPa) Example: p = 1000 hPa, T = 300 K → 96 × 300 ÷ 1000 ≈ 29 ft per hPa In ISA, 1 hPa ≈ 27 ft at MSL , ≈ 50 ft at 20 000 ft, ≈ 100 ft at 40 000 ft Rule of thumb for altimetry: 30 ft per hPa low down; 1000 ft ≈ 33–36 hPa 0 200 400 600 800 1000 0 10 000 20 000 30 000 40 000 50 000 60 000 Pressure (hPa) Height (ft) 850 hPa · 5 000 ft 700 · 10 000 ft 500 · 18 000 ft 300 · 30 000 ft 200 · 39 000 ft Height for 1 hPa (ISA) at MSL 27 ft 20 000 ft 50 ft 40 000 ft 100 ft 1013
Chapter 2 · Atmospheric Pressure
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pressure falls as you climb, but not at a steady rate. Near the ground the air is dense, so each step upward removes a lot of weight and pressure falls quickly. Higher up the air is thin, so pressure falls more slowly. By about five and a half to six kilometres pressure has roughly halved, and by one hundred kilometres it is practically a vacuum. A handy formula gives the height change for one hectopascal: ninety-six times the absolute temperature, divided by the pressure, in feet. At one thousand hectopascals and three hundred kelvin, that is about twenty-nine feet. In the standard atmosphere, one hectopascal is about twenty-seven feet at sea level, about fifty feet at twenty thousand feet, and about one hundred feet at forty thousand. Warm air stretches these values; cold air shrinks them. For everyday altimeter sums, we use thirty feet per hectopascal.
Warm and cold columns
Pressure falls faster in cold air 700 hPa 850 hPa 1000 hPa fixed height pressure here below 700 hPa pressure here 700–850 hPa COLD column · dense pressure surfaces sit low WARM column · expanded pressure surfaces sit high Pressure surfaces are low over cold air and high over warm air : at any height, pressure is higher over the warm column . Isobars dip from high towards low.
Chapter 2 · Atmospheric Pressure
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Cold air is denser than warm air, so a column of cold air is shorter than a column of warm air holding the same mass. Start both columns with one thousand hectopascals at the ground. In the cold column, the eight hundred and fifty and seven hundred hectopascal surfaces sit low; in the warm column they sit high. In other words, pressure falls faster with height in cold air and more slowly in warm air. Now draw a line at a fixed height across both columns. Over the cold air you are already above the seven hundred surface, so the pressure is lower. Over the warm air you are still below it, so the pressure is higher. So at any given height, pressure is higher over warm air than over cold air. This explains why an aircraft holding a constant pressure level is physically lower when it flies over cold air.
A daily rhythm
Semi-diurnal variation of pressure Pressure rises and falls twice a day like a tide Maxima near 1000 and 2200 local time (10 o’clock is the main one)Minima near 0400 and 1600 local timeRange about 3–5 hPa in the tropics , under about 1.5 hPa in middle latitudes, almost nil at the poles Not simply heating: it is a natural ~12-hour oscillation of the atmosphere, lagging temperature by about 3 hours In the tropics a pressure change that breaks this pattern is a sign of a real weather system 0000 0400 0800 1200 1600 2000 2400 -2 -1 0 +1 +2 Local time Pressure change (hPa) 1000 max 2200 max 0400 min 1600 min Two highs and two lows a day · range about 3 hPa in the tropics
Chapter 2 · Atmospheric Pressure
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Even on a quiet day, pressure rises and falls twice every twenty-four hours, almost like a tide. The highs come at about ten in the morning, which is the main peak, and ten at night. The lows come at about four in the morning and four in the afternoon, local time. You might expect pressure to be lowest in the hot afternoon and highest at the cold dawn, but the pattern does not follow temperature directly: there is a lag of about three hours, and the swing is best explained as a natural twelve-hour oscillation of the whole atmosphere, driven by the sun and travelling round the Earth. The swing is largest near the equator, about three to five hectopascals, small in middle latitudes, and almost nothing at the poles. That is why, in the tropics, a forecaster first removes this daily swing before deciding whether pressure is really falling.
Instruments
Measuring and recording pressure Mercury barometer Air pressure balances a column of mercury. The most accurate ; corrected for index error, gravity and temperature.
Aneroid barometer A sealed, partly evacuated capsule flexes with pressure. Less accurate but handy and portable , so widely used.
Altimeter An aneroid barometer with its scale marked in feet , plus a sub-scale for setting the datum pressure.
Barograph Records pressure continuously on a drum chart, daily or weekly, showing the tendency .
Chapter 2 · Atmospheric Pressure
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The standard instrument is the mercury barometer, in which the weight of the air balances a column of mercury. It is the most accurate, but its readings must be corrected for instrument index error, for gravity, which changes with latitude, and for temperature. The aneroid barometer uses a sealed, partly evacuated metal capsule that flexes as pressure changes. It is less accurate but compact and convenient, so it is widely used. Your altimeter is simply an aneroid barometer whose scale is marked in feet instead of hectopascals, using the standard atmosphere to convert, with a sub-scale on which you set the datum pressure. And to keep a continuous record, stations use a barograph, which traces pressure on a rotating drum, daily or weekly. That trace shows the pressure tendency at a glance.
Upper-air charts
Contours and thickness Upper charts show the height of a pressure surface; lines of equal height are contours (isohypses) Heights in geopotential metres , labelled in decametres: 5280 gpm is plotted as 528 Interval: 40 gpm at 700 and 500 hPa; 80 gpm at 300 and 200 hPa Low contours mean low pressure at that height; they behave like isobars Thickness = height difference between two pressure levels; large over warm air , small over coldSo thickness lines are the isotherms of the layer’s mean temperature Upper-air chart · 500 hPa contours (dam) 572 576 580 584 trough: low contours interval 40 gpm (4 dam) 500 hPa 1000 hPa small thickness cold layer large thickness warm layer
Chapter 2 · Atmospheric Pressure
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
On upper-air charts, forecasters do not draw isobars at a fixed height. Instead they take one pressure surface, say five hundred hectopascals, and draw lines joining places where that surface lies at the same height. These lines are called contours, or isohypses. Heights are in geopotential metres, which are almost the same as ordinary metres, and are labelled in decametres, so five thousand two hundred and eighty is written five two eight. Contours are drawn every forty geopotential metres on the seven hundred and five hundred hectopascal charts, and every eighty on the three hundred and two hundred charts. Where a contour is low, pressure at that height is low, so contours behave just like isobars. The height difference between two pressure levels is the thickness of the layer. Warm air expands, so thickness is large over warm air and small over cold air, which makes thickness lines the isotherms of the layer’s mean temperature. As a check, the three hundred hectopascal surface in ISA lies at about nine thousand one hundred and sixty metres.
Reading the isobars
Pressure gradient and pressure tendency Isobar : line joining places of equal (MSL) pressure, usually drawn every 2 hPa Pressure gradient : change of pressure across the isobars, from high to lowIsobars close together = steep gradient = strong wind ; far apart = flat gradient, light windPressure tendency : change with time; past 24 h in India , past 3 h in higher latitudesIsallobars join places of equal pressure tendencyLows move towards and deepen at the isallobaric low (greatest fall); an isallobaric high means a system weakening 1000 1004 1008 1012 L steep gradient isobars close · strong wind flat gradient isobars wide · light wind Isobars every 4 hPa · northern hemisphere Isallobars: lines of equal pressure change in 3 h −3 −2 −1 −4 L The low heads for the isallobaric low (greatest fall)
Chapter 2 · Atmospheric Pressure
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
When pressures from many stations are reduced to sea level and plotted, we join equal values with isobars, usually every two hectopascals. The pressure gradient is how fast pressure changes as you cross the isobars, measured from high towards low. Isobars packed close together mean a steep gradient and strong wind; isobars far apart mean a weak or flat gradient and light wind. Pressure also changes with time, and that change is the pressure tendency. In India it is worked out over the past twenty-four hours, which removes the daily tide; in higher latitudes over the past three hours. Lines joining places with equal tendency are isallobars. The area of greatest fall is the isallobaric low, and a surface low tends to move towards it and deepen. An isallobaric high, the area of greatest rise, points to a system that is weakening or a high building in.
Altimetry words
Height, altitude, elevation and the transition Transition level (TL) · lowest flight level · 1013.2 set at and above Transition altitude (TA) · QNH set at and below transition layer Mean sea level flight level: 1013.2 set Height above aerodrome · QFE Altitude above MSL · QNH Elevation of the aerodrome Height is above a datum such as the aerodrome; altitude is above MSL; elevation is a ground point above MSL. Climbing, change to 1013.2 at the TA; descending, to QNH at the TL.
Chapter 2 · Atmospheric Pressure
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
A few words need to be exact. Height is the vertical distance above a particular datum, such as the aerodrome. Altitude is the vertical distance above mean sea level. Elevation is the height of a point on the ground, like an aerodrome, above mean sea level. Near the ground aircraft fly on the local QNH, so their altimeters show altitude. The transition altitude is the altitude at or below which you fly on QNH. The transition level is the lowest flight level available above it, and at or above it everyone sets the standard one thousand and thirteen point two hectopascals, so all aircraft share one datum. The airspace between the two is the transition layer. Flight levels are surfaces of constant pressure, labelled in hundreds of feet on the standard setting and spaced at pressure intervals equal to five hundred feet, so flight level fifty is five thousand feet on one thousand and thirteen.
Altimeter settings
QFE, QNH, QFF, QNE and pressure altitude QFE Pressure at aerodrome level. Set it and the altimeter reads zero (height) on the ground .
QNH Station pressure reduced to MSL using ISA . Set it and the altimeter reads aerodrome elevation on the ground; used for terrain clearance.
QFF Station pressure reduced to MSL using the actual temperature . Used to plot synoptic charts and draw isobars.
QNE The altitude shown on the ground with 1013.2 hPa set: the aerodrome’s pressure altitude. Used at very high aerodromes.
Pressure altitude Reading with 1013.2 hPa set. Above the TL it is given as a flight level: 19 000 ft → FL190 .
Regional QNH Forecast lowest QNH in an altimeter setting region for the next hour, so terrain clearance is never overestimated.
Chapter 2 · Atmospheric Pressure
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the settings. QFE is the pressure at aerodrome level; with it set, the altimeter reads zero on the runway, so in flight it shows height above the aerodrome. QNH is the station pressure reduced to sea level using the standard atmosphere; with it set, the altimeter reads the aerodrome elevation on the ground and altitude in flight, which is what you need for terrain clearance and separation below the transition altitude. QFF is also reduced to sea level, but using the actual temperature, and it is the value meteorologists plot on synoptic charts to draw isobars. QNE is not a pressure at all: it is the altitude the altimeter shows on the ground when one thousand and thirteen point two is set, and it is used at very high aerodromes where QFE would be off the scale. With the standard setting, the altimeter shows pressure altitude. Regional QNH is the lowest QNH forecast in a region for the coming hour, so it always errs on the safe side.
Worked examples
Solving setting problems with 30 ft per hPa QNH 1000, QFE 950 : elevation = (1000 − 950) × 30 = 1500 ft ; on 1013, the altimeter shows (1013 − 950) × 30 = 1890 ft QNH 1020, QFE 970 : elevation = 50 × 30 = 1500 ft ; on 1013, reads (1013 − 970) × 30 = 1290 ft QFE 1000, elevation 270 ft , 27 ft/hPa: 270 ÷ 27 = 10 hPa, so QNH 1010 QNH 1005, elevation 160 m , 8 m/hPa: 20 hPa, so QFE 985 QNH is higher than QFE at any aerodrome above sea level; at MSL, QFE = QNH = QFF Setting lower than QNH → reads too low; higher than QNH → reads too high aerodrome · QFE 950 datum MSL · QNH 1000 datum 1013.2 datum · 390 ft below MSL 50 hPa × 30 = 1500 ft 0 1 2 3 4 5 6 7 8 9 ALT 0950 0 QFE set: reads 0 0 1 2 3 4 5 6 7 8 9 ALT 1000 1 500 QNH set: 1500 ft 0 1 2 3 4 5 6 7 8 9 ALT 1013 1 890 1013 set: 1890 ft
Chapter 2 · Atmospheric Pressure
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us work some examples using thirty feet per hectopascal. An aerodrome has a QFE of nine hundred and fifty and a QNH of one thousand. The difference is fifty hectopascals, times thirty, so the elevation is one thousand five hundred feet. If the pilot sets one thousand and thirteen instead, the difference from QFE is sixty-three hectopascals, so the altimeter shows one thousand eight hundred and ninety feet; that is the QNE. Second: QFE one thousand, elevation two hundred and seventy feet, using twenty-seven feet per hectopascal. Two hundred and seventy divided by twenty-seven is ten, so QNH is one thousand and ten. Third, in metres: QNH one thousand and five at an aerodrome one hundred and sixty metres high, with eight metres per hectopascal. That is twenty hectopascals, so QFE is nine hundred and eighty-five. Remember: above sea level QNH is always higher than QFE, and at a sea-level aerodrome QFE, QNH and QFF are all the same.
Standard isobaric levels
Pressure levels and their ISA altitudes The upper-air charts you will use, with the pressure altitude of each in ISA.
Pressure level Pressure altitude (ft) Flight level Approx. height (km) 850 hPa 5 000 FL50 1.5 700 hPa 10 000 FL100 3.0 500 hPa 18 000 FL180 5.5 400 hPa 24 000 FL240 7.2 300 hPa 30 000 FL300 9.2 200 hPa 38 000 to 39 000 FL390 (often given as FL380) 11.8 100 hPa 53 000 FL530 16.2
Remember the pattern 850–5, 700–10, 500–18, 300–30, 200–39 (thousands of feet).
Chapter 2 · Atmospheric Pressure
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Upper-air charts are drawn for standard pressure levels, and you must know roughly where each sits in the standard atmosphere. Eight hundred and fifty hectopascals is about five thousand feet, flight level fifty. Seven hundred is about ten thousand feet. Five hundred is about eighteen thousand feet, the level where half the atmosphere lies below you. Four hundred is about twenty-four thousand. Three hundred is about thirty thousand. Two hundred is about thirty-eight to thirty-nine thousand feet; you will see it quoted as flight level three hundred and eighty or three hundred and ninety. And one hundred hectopascals is about fifty-three thousand feet. So if a question gives you a height, pick the nearest of these: forty thousand feet, for example, is closest to the two hundred hectopascal level.
Altimeter errors
High to low, beware below Flying from high to low pressure without resetting: the altimeter over-reads (you are lower than shown) Flying from low to high : it under-reads (you are higher than shown) Flying from warm to cold air : over-reads ; cold to warm: under-reads Northern hemisphere: wind from port (drift to starboard) means heading towards low, so it over-reads ; wind from starboard, under-reads. Reverse in the south D value = true − indicated altitude; altimeter correction = indicated − trueRough correction: 30 ft per hPa that MSL pressure differs from 1013.2, plus 4% of indicated altitude per 10 °C from ISA H high · or warm L low · or cold the pressure level the altimeter follows true 5000 ft true 4400 ft altimeter reads 5000 ft all the way HIGH TO LOW · BEWARE BELOW
Chapter 2 · Atmospheric Pressure
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Your altimeter assumes the standard atmosphere above whatever datum you have set. If you fly from high pressure towards low pressure without resetting, the pressure surface you are following slopes downward, so you descend while the altimeter still shows the same figure: it over-reads, and you are lower than you think. From low to high it under-reads. Temperature does the same: in air colder than standard the pressure levels are squeezed together, so flying from warm to cold the altimeter over-reads. Hence the saying, high to low, or hot to cold, look out below. A drift clue: in the northern hemisphere, a wind from the left, which drifts you to the right, means you are heading towards low pressure, so again you are lower than indicated. The D value is true altitude minus indicated altitude. As a rough correction, allow thirty feet for every hectopascal the sea-level pressure differs from standard, and four per cent of the indicated altitude for every ten degrees the temperature differs from ISA.
Pressure patterns
Low, high, trough, ridge and col Low (depression) Trough Col Ridge High (anticyclone) L anticlockwise, inward (NH) L V-shaped isobars, wind veers across H H L L col light, variable winds H rounded (U) isobars, fair H clockwise, outward (NH) Northern hemisphere: winds go anticlockwise and inward round a low , clockwise and outward round a high ; the reverse in the south.
Chapter 2 · Atmospheric Pressure
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
When sea-level pressures are plotted and isobars drawn every two hectopascals, a few standard shapes appear. A low is an area enclosed by isobars with the lowest pressure in the middle; with two or more closed isobars it is a depression, and more intense systems become cyclones. In the northern hemisphere winds circle a low anticlockwise and spiral inward. A trough is a V-shaped tongue of low pressure stretching out from a low; pressure along it is lower than on either side. A high, or anticyclone, has the highest pressure at the centre, with winds circling clockwise and spiralling outward in the north. A ridge is a rounded tongue of high pressure stretching out from a high. And a col is the saddle-shaped region between two highs and two lows, where pressure is nearly uniform. In the southern hemisphere the directions of circulation are reversed.
What each pattern brings
Pressure patterns and their weather Pattern Air motion Weather and visibility Wind Low / depression Convergence and rising air Bad weather , cloud and rain; but visibility better than in a highAnticlockwise in NH; backs in a low Trough Convergence, rising Bad weather, often a line of cloud; e.g. the monsoon trough over the Indo-Gangetic plain Changes sharply across it; veers as it passes (NH) High / anticyclone Divergence and sinking (subsidence) Fair , but poor visibility (haze, smoke, fog) under a subsidence inversion Light; clockwise in NH, veering Ridge Sinking Fair weather Veers across it Col Little motion Mixed: fog in winter, thunderstorms in summer Light and variable
A blocking anticyclone stays nearly still and blocks lows moving across its latitudes. A cold anticyclone warms with time as its sinking air is compressed.
Chapter 2 · Atmospheric Pressure
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each pattern brings its own weather. In a low, air converges near the ground and has to rise, so it cools and makes cloud and rain: lows mean bad weather. Visibility, though, is usually better than in a high, because the rising, stirred air carries pollution away. A trough behaves like a low stretched into a line, often with a band of bad weather; the monsoon trough across the Indo-Gangetic plain is a good example, and the wind changes direction sharply as it passes, veering in the northern hemisphere. In a high, air sinks and spreads out. Sinking air warms and dries, so skies are often fair, but the subsidence inversion traps haze and smoke underneath, so visibility is often poor. Ridges are fair too. In a col winds are light and variable, and the weather is a mix: fog on winter nights, thunderstorms in summer. Finally, a blocking anticyclone sits almost still and diverts the lows that would normally move across.
Summary
What to take into the exam Units 1013.25 hPa = 29.92 in = 760 mm. hPa × 0.02953 = inches. Altimeter is an aneroid.
With height Falls faster low down and in cold air. 27 ft/hPa at MSL; use 30. Half by about 5.5 km.
Warm and cold At a given height, pressure is higher over warm air. Thickness large over warm air.
Daily tide Highs 1000 and 2200, lows 0400 and 1600 local; 3–5 hPa in the tropics.
Settings QFE reads zero; QNH reads elevation (ISA); QFF for charts (actual temp); QNE = reading on 1013.
Levels 850–5000, 700–10 000, 500–18 000, 300–30 000, 200–39 000 ft. Contours 40 / 80 gpm.
Errors High to low, warm to cold: over-reads. Drift to starboard (NH): lower than indicated.
Patterns Low: rising, bad weather, better visibility. High: subsidence, fair, poor visibility. Col: light variable winds.
Chapter 2 · Atmospheric Pressure
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is what to carry into the exam. One thousand and thirteen point two five hectopascals equals twenty-nine point nine two inches and seven hundred and sixty millimetres, and the altimeter is an aneroid barometer. Pressure falls fastest near the ground and in cold air; use thirty feet per hectopascal. At any height, pressure is higher over warm air, and thickness is greater over warm air. The daily pressure tide peaks at ten and twenty-two hours and dips at four and sixteen, and is largest in the tropics. QFE reads zero on the ground, QNH reads elevation, QFF is used for charts, and QNE is what the altimeter shows on one thousand and thirteen. Know the standard levels: eight fifty is five thousand feet, seven hundred is ten thousand, five hundred eighteen thousand, three hundred thirty thousand, two hundred about thirty-nine thousand. High to low, or warm to cold, the altimeter over-reads. And lows bring bad weather with better visibility; highs bring fair weather with poor visibility.