Performance · Chapter 6
Class A Take-off Engine failure at the worst moment: TOD, TOR and ASD, balanced field, the limiting masses, and reduced thrust.
GO STOP V1
Class A Take-off © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
For an airliner the take-off is planned around one question: what if an engine fails at the worst possible moment? The answer decides how much runway we need, what V1 is, and how heavy we can be. In this lesson we'll build the Class A take-off rules from that single assumption.
The assumption An engine fails at the worst moment
Balanced field Choosing V1
Surface Wet and contaminated
Mass limits The lowest one wins
Less thrust Assumed temperature, derate
Chapter 6 · Class A Take-off
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Class A take-off rules all grow from one assumption: an engine can fail at the most critical point. We'll define the distances that follow from it, see how V1 balances going against stopping, look at wet and contaminated runways, list the limits on take-off mass, and finish with reduced thrust take-offs.
Distances
Continue or stop
engine fails (VEF)
35 ft
TOD: continue to 35 ft
ASD: accelerate to V1, then stop
Each distance is the GREATER of the engine-failure case and 1.15 × all engines
Chapter 6 · Class A Take-off
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Imagine an engine fails at VEF, just before V1. The pilot has two choices. Continue: accelerate on the remaining engines, rotate, and reach thirty-five feet at V2. That distance is the take-off distance. Or stop: idle, brakes, spoilers. That's the accelerate-stop distance. For each distance, the rules take the greater of the engine-failure figure and one point one five times the all-engines figure, so that a normal take-off also has a margin.
Distances
The three Class A distances Distance Greater of Must be within TOD Engine failure at VEF to 35 ft; 1.15 × all engines to 35 ft TODA TOR Engine failure to midway between VLOF and 35 ft; 1.15 × all engines to that point TORA ASD Accelerate to V1 (engine failure), then stop; all engines to V1, then stop ASDA
Chapter 6 · Class A Take-off
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the three distances side by side. The take-off distance runs to thirty-five feet and must fit within TODA. The take-off run ends halfway between lift-off and thirty-five feet, so clearway can only be used for the airborne part, and must fit within TORA. And the accelerate-stop distance must fit within ASDA.
Balanced field
V1: going versus stopping Higher V1 → longer ASD (more speed to stop) Higher V1 → shorter TOD (less to do on one engine) Where they meet: balanced V1 With stopway or clearway: unbalanced V1 can raise the mass
V1 → Distance required → ASD TOD balanced V1 balanced field length
Chapter 6 · Class A Take-off
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
V1 sets the balance between going and stopping. A higher V1 means more speed to get rid of if you stop, so the accelerate-stop distance grows. But it also means less accelerating to do on one engine if you go, so the take-off distance shrinks. Where the two curves cross is the balanced V1, and the distance there is the balanced field length. If the runway has a stopway or clearway, choosing V1 away from the balance point lets you use them and lift a heavier load.
Continue or stop
After V1: go Failure at or after V1: continue Rotate at VR, reach V2 by 35 ft Gear up once climbing
engine fails (VEF)
35 ft
TOD: continue to 35 ft
ASD: accelerate to V1, then stop
Each distance is the GREATER of the engine-failure case and 1.15 × all engines
Chapter 6 · Class A Take-off
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
If the failure comes at or after V1, the pilot must continue. Rotate at VR, lift off on the remaining engine, and reach V2 by thirty-five feet. Once positively climbing, the gear comes up to cut drag.
Continue or stop
Before V1: stop Failure before V1: reject Idle, maximum braking, spoilers, reverse Must stop within ASDA Limited by brake energy (VMBE)
engine fails (VEF)
35 ft
TOD: continue to 35 ft
ASD: accelerate to V1, then stop
Each distance is the GREATER of the engine-failure case and 1.15 × all engines
Chapter 6 · Class A Take-off
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
If the failure comes before V1, the pilot rejects the take-off: thrust to idle, maximum braking, spoilers up and reverse thrust. The aeroplane must stop within the accelerate-stop distance available. The brakes have to absorb a huge amount of energy, which is why V1 can't exceed the maximum brake energy speed.
Surface
Wet and contaminated runways
Dry best braking: the reference
Wet poorer braking → lower V1
Contaminated drag on the wheels, aquaplaning
15 ft screen (wet)
35 ft (dry)
Reverse thrust may be credited in the accelerate-stop distance on wet and contaminated runways.
Chapter 6 · Class A Take-off
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a wet runway, braking is poorer, so the accelerate-stop distance grows. To balance that, V1 is reduced, and the take-off distance is allowed to end at a screen of fifteen feet instead of thirty-five. On a contaminated runway with water, slush or snow there's extra drag on the wheels and much poorer braking, so special data are used and the allowed mass usually falls. Reverse thrust may be credited on wet and contaminated runways.
Mass limits
The lowest limit wins Field : TOD, TOR, ASD fit the runwayClimb : segment gradients metObstacle : net path clears by 35 ftTyre and brake energy Landing mass at destination
Take-off mass = lowest of…
Structural (MTOM) Field length Climb gradient Obstacle clearance Tyre speed Brake energy Landing mass at destination + burn
Here obstacles limit: the shortest bar wins.
Chapter 6 · Class A Take-off
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The take-off mass is limited by several things at once. The structural maximum. The field length, so the distances fit the runway. The climb, so the gradients we'll meet next lesson are achieved. Obstacles along the departure. Tyre speed and brake energy. And the landing mass at the destination plus the fuel you'll burn. The lowest of all these is the take-off mass you can use.
Less thrust
Assumed temperature and derate If the runway allows, use less thrust Assumed temperature : tell the engine it is hotterDerate : a lower fixed rating, with its own dataSaves engine wear; full thrust always available (assumed temperature) Improved climb : higher V speeds on a long runway for a better climb mass
0 15 30 45 60 Outside air temperature (°C) → Take-off thrust → Full thrust actual 15 °C assumed 50 °C
Chapter 6 · Class A Take-off
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
When the runway is longer than needed, we can take off with less than full thrust, which saves engine wear. With the assumed temperature method, the engine is told the air is hotter than it really is, and the thrust is set for that temperature. With a derate, the engine is given a lower fixed rating with its own performance data. A related idea is the improved climb: on a long runway, using higher V speeds gives a better climb gradient and so a higher climb-limited mass.
Assumption Engine failure at VEF
Distances Greater of engine-out and 1.15 × all engines
Wet Lower V1, 15 ft screen
Mass Lowest of field, climb, obstacle, tyre, brake, landing
Thrust Assumed temperature or derate
Chapter 6 · Class A Take-off
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Class A assumes an engine failure at the critical point. Each distance is the greater of the engine-out case and one point one five times the all-engines case. The balanced V1 is where take-off and accelerate-stop distances are equal. A wet runway gives a lower V1 and a fifteen foot screen. The take-off mass is the lowest of all the limits. And when the runway allows, use less thrust.