Performance · Chapter 1
Definitions and Speeds The language of performance: runway distances, take-off speeds, gradients and the performance classes.
V1 VR V2
Speeds · Distances · Classes
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to Performance. Before we can work out whether an aeroplane can take off, climb or land safely, we need the words and speeds the subject is built on. In this first lesson we'll meet the declared runway distances, the take-off speeds, the difference between a climb gradient and a rate of climb, and the performance classes that decide which rules apply.
Roadmap
What this lesson covers Declared distances TORA, TODA, ASDA, LDA
Stopway and clearway What each adds
Take-off speeds VMCG, V1, VR, VLOF, V2
Stall and control VS, VMCA, VMU
Gradient vs rate Two ways to measure a climb
Classes Which rules apply: A or B
Chapter 1 · Definitions and Speeds
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here's the plan. First the declared distances that every runway publishes, and the stopway and clearway beyond it. Then the take-off speeds, in order, and the stalling and minimum control speeds behind them. Then the difference between a climb gradient and a rate of climb, and finally the performance classes, which decide which set of rules you use.
Declared distances
What the runway gives you
stopway
clearway
TORA: take-off run available
ASDA = TORA + stopway
TODA = TORA + clearway
LDA (here with a displaced threshold)
Chapter 1 · Definitions and Speeds
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every runway publishes four declared distances, and the aeroplane will show you each one in turn. First, TORA, the take-off run available. This is the runway itself, the length the wheels may use for the take-off run. Second, TODA, the take-off distance available. After lift-off the aeroplane climbs out over the clearway, so TODA is TORA plus the clearway. Third, ASDA, the accelerate-stop distance available. Now the take-off is abandoned, and the aeroplane may brake to a stop on the stopway. So ASDA is TORA plus the stopway. Fourth, LDA, the landing distance available. The aeroplane touches down beyond the displaced threshold, so LDA runs from that threshold to the far end of the runway. Keep it simple. Clearway adds only to TODA, stopway adds only to ASDA, and neither one adds to TORA or LDA.
Stopway and clearway
Two very different extensions
Stopway
strong enough to stop on adds to ASDA
Clearway obstacle-free, rises ≤ 1.25 % flown over · adds to TODA
screen height
abandoned take-off: stop
Neither may be used for a normal take-off run or for landing.
Chapter 1 · Definitions and Speeds
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Students often mix these up. Here the aeroplane has abandoned its take-off and stopped on the stopway: a paved area beyond the runway, at least as wide as the runway, marked with yellow chevrons and strong enough to carry the aeroplane. It only adds to the accelerate-stop distance. The clearway is different: an obstacle-free area beyond the runway end, at least one hundred and fifty-two metres wide, that a continued take-off flies over on its way to the screen height. Nothing may stick up through a plane rising at one and a quarter per cent, it may be over land or water, and the clearway you can count is limited to half the take-off run available. It only adds to the take-off distance. Neither may be used for a normal take-off run or for landing.
Take-off speeds
One take-off, five speeds
35 ft screen VMCG control on the ground, rudder only V1 decision speed VR rotate VLOF lift-off V2 safety speed at the screen
Chapter 1 · Definitions and Speeds
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now for the take-off speeds: watch one take-off, and we will pause at each speed in the order you meet it. First, VMCG, the minimum control speed on the ground. Above this speed, if an engine fails, the pilot can still keep the aeroplane straight on the runway using the rudder alone. Second, V1, the decision speed. If something goes wrong before V1, the pilot stops on the runway. After V1 there is not enough runway left to stop, so the take-off must continue. Third, VR, the rotation speed. Here the pilot pulls back and raises the nose, but the main wheels are still on the runway. Fourth, VLOF, the lift-off speed. The wings now make enough lift, and the wheels leave the ground. Fifth, V2, the take-off safety speed. The aeroplane must reach V2 by the screen height, thirty-five feet above the runway, and it climbs away safely at this speed even with one engine failed. So the order never changes. VMCG, V1, VR, VLOF, and then V2.
Stall and control
The speeds behind the speeds Speed Meaning VS / VSR Stalling speed / reference stalling speed in a given configuration VMCG Minimum control speed on the ground: critical engine failed, rudder only (no nosewheel steering), within 30 ft of the centreline VEF Speed at which the critical engine is assumed to fail: not below VMCG VMCA Minimum control speed in the air: keep straight with up to 5° bank, an engine failed VMU Minimum unstick speed: the lowest speed at which the aeroplane can lift off VMBE Maximum brake energy speed: the highest speed from which the brakes can stop it VTYRE Maximum tyre speed: limited by the tyre rating Rules VMCG ≤ V1 ≤ VR · VR ≥ 1.05 VMCA · V2 ≥ 1.1 VMCA and ≥ 1.13 VSR (jets)
Chapter 1 · Definitions and Speeds
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
These are the speeds that the take-off speeds are built on. The stalling speed in the take-off configuration sets a floor for V2. The two minimum control speeds set a floor for V1 and VR, because with an engine failed you must be able to stay straight. The minimum unstick speed is the lowest speed the aeroplane can physically lift off at. And two speeds set ceilings: the maximum brake energy speed and the maximum tyre speed. Three rules tie them together. V1 can't be below VMCG, or you couldn't keep straight after an engine failure, and it can't be above VR. VR must be at least five per cent above VMCA. And V2 must be at least ten per cent above VMCA and, for jets, thirteen per cent above the reference stalling speed.
Engine failure
VEF and the critical engine
engine fails at VEF VEF: the speed at which the critical engine is assumed to fail Never below VMCG. V1 comes just after it, allowing for the pilot's reaction. Critical engine: the one whose failure affects performance or handling the most. VMCG is proved with the critical engine failed, rudder only, keeping within 30 ft of the centreline.
Chapter 1 · Definitions and Speeds
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two more terms you will hear with every take-off. First, the critical engine. It is the engine whose failure would hurt performance or handling the most. Second, VEF, the speed at which we assume that engine fails during the take-off run. VEF can never be below VMCG, otherwise the pilot could not keep the aeroplane straight. Third, V1 comes just after VEF. The gap is the time the pilot needs to recognise the failure and react. And remember how VMCG is proved. Critical engine failed, rudder only, and the aeroplane must stay within thirty feet of the centreline.
The V1 concept
Stop or go?
Engine-failure speed → Distance required → ASDR (stop) TODR one engine (go) balanced V1 before V1: STOP after V1: GO
Chapter 1 · Definitions and Speeds
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is why V1 matters: the same take-off, twice, with an engine failing at two different moments. First, the engine fails before V1. The aeroplane must stop, because there is not enough runway left to reach thirty-five feet on one engine. Second, the engine fails after V1. Now the aeroplane must go, because it is too fast to stop in the runway that remains. So V1 is the line between stopping and going. Two things move that line. On a wet runway braking is poorer, so V1 is lower. And when the stopping distance and the one-engine take-off distance are equal, the field is called balanced, which gives the shortest runway for that mass. You will meet the balanced field again in the Class A take-off lesson.
Gradient vs rate
Two ways to measure a climb Gradient : height gained ÷ horizontal distance (%)Decides whether you clear obstacles Rate of climb : height gained per minute (ft/min)Decides how quickly you reach altitude ROC ≈ gradient × ground speed
gradient = height ÷ distance
distance over the ground
height gained
Gradient (%): clears obstacles
Rate of climb (ft/min): gains height in time
ROC ≈ gradient × ground speed
Chapter 1 · Definitions and Speeds
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
A climb can be measured two ways. The gradient is height gained divided by distance travelled, as a percentage. That's what decides whether you clear a hill or a mast, so take-off rules are written in gradients. The rate of climb is height gained per minute, which decides how quickly you reach your cruising level. They're linked by ground speed: a headwind lowers your ground speed, so the same rate of climb gives a steeper gradient over the ground.
Gradient vs rate
After lift-off Gear retracted once climbing Hold V2 to the acceleration height Climb gradient must meet the minimum
gradient = height ÷ distance
distance over the ground
height gained
Gradient (%): clears obstacles
Rate of climb (ft/min): gains height in time
ROC ≈ gradient × ground speed
Chapter 1 · Definitions and Speeds
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
After lift-off the pilot holds V2 or a little above, and once the aeroplane is safely climbing the gear is retracted to reduce drag. The regulations demand a minimum climb gradient in this phase, even with an engine failed, so that the aeroplane clears everything on the departure path. We'll see those gradients in the Class A lessons.
Performance data
Measured, gross and net Measured : new aeroplane, test pilotsGross : the average fleet aeroplaneNet : gross minus a safety marginObstacle clearance always uses net
measured gross net Measured : test pilots, new aeroplaneGross : what an average fleet aeroplane achievesNet : gross minus a safety margin → obstacles
Chapter 1 · Definitions and Speeds
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Performance figures come in three flavours. Measured performance is what the test pilots achieve in a brand-new aeroplane, better than the fleet will ever do. Gross performance is what an average aeroplane in the fleet should achieve, properly maintained and flown. Net performance is the gross figure reduced by a safety margin set by the authority, to allow for below-average aeroplanes and technique. Obstacle clearance is always worked out on the net figures.
Density altitude
Working out density altitude ISA temperature = 15 − 2 × (PA ÷ 1 000) DA ≈ PA + 120 × (OAT − ISA) PA ≈ elevation + 30 × (1013 − QNH) Higher DA: longer take-off, poorer climb
Pressure altitude 2 000 ft, OAT +30 °C ISA at 2 000 ft = 15 − 2 × 2 = 11 °C ISA deviation = 30 − 11 = +19 °C DA ≈ PA + 120 × deviation = 2 000 + 2 280 Density altitude ≈ 4 300 ft Pressure altitude ≈ elevation + 30 × (1013 − QNH) The aeroplane performs as if it were at about 4 300 ft.
Chapter 1 · Definitions and Speeds
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Density altitude is the pressure altitude corrected for temperature, and there's a quick way to estimate it. First the ISA temperature at the pressure altitude: fifteen, minus two degrees per thousand feet. At two thousand feet that's eleven degrees. If the outside air is thirty degrees, the deviation is plus nineteen. Multiply by a hundred and twenty and add it to the pressure altitude: two thousand plus two thousand two hundred and eighty, about four thousand three hundred feet. The aeroplane performs as if it were that high.
Runway end
Runway end safety area (RESA)
runway strip RESA ≥ 90 m (240 m recommended) ≥ 2 × width Reduces damage if an aeroplane undershoots or overruns. It is not part of any declared distance.
Chapter 1 · Definitions and Speeds
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
One more area at the end of the runway: the runway end safety area. It lies beyond the runway strip, centred on the extended centreline, and reduces the damage if an aeroplane undershoots or overruns. It must be at least ninety metres long, two hundred and forty is recommended, and at least twice the runway width. It isn't part of any declared distance.
Performance classes
Which rules apply?
Class A
all multi-engine jets turboprops > 9 seats or > 5 700 kg
engine failure assumed at any point
Class B
propeller aeroplanes ≤ 9 seats and ≤ 5 700 kg
singles and light twins
Class C
piston aeroplanes above the Class B limits
rare today
Chapter 1 · Definitions and Speeds
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The rules you apply depend on the aeroplane's performance class. Class A covers all multi-engine jets, and multi-engine turboprops with more than nine passenger seats or heavier than five thousand seven hundred kilograms. Their rules assume an engine can fail at any point. Class B covers propeller aeroplanes with nine seats or fewer and five thousand seven hundred kilograms or less, so single-engine aeroplanes and light twins. Class C is for larger piston aeroplanes, and is rarely met today.
Distances TORA; ASDA = TORA + stopway; TODA = TORA + clearway; LDA
Order VMCG ≤ V1 ≤ VR < VLOF < V2
Screen V2 by 35 ft (Class A)
Floors V2 ≥ 1.13 VSR (jets) and ≥ 1.1 VMCA; VR ≥ 1.05 VMCA
Gradient Height ÷ distance; for obstacles
Classes A: jets and big turboprops; B: small propeller aeroplanes
Chapter 1 · Definitions and Speeds
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. TORA is the runway you can run on; add the stopway for ASDA and the clearway for TODA. The take-off speeds come in the order VMCG, V1, VR, VLOF, then V2, which must be reached by thirty-five feet. Gradient is height over distance and matters for obstacles. And the performance class, A or B, decides which rules you follow.