Principles of Flight · Chapter 4
Aerofoils and Subsonic Airflow The shape of a wing section, the angles that describe it, how air flows and presses on it, where its lift acts and why it wants to pitch.
computed streamlines · cambered section at 6°
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the aerofoil, the shape that makes flight possible. In this lesson we take a wing apart one slice at a time. We will name every part of a section, separate the angle of attack from the pitch attitude, and watch how the air divides, speeds up and presses on the surface. Then we will find where the lift really acts, why that point moves, and why a cambered wing always wants to pitch nose down. Everything that follows in this course is built on these ideas.
Lesson map
From the shape of a section to the lift it makes 1 · The section Chord, camber, thickness, leading-edge radius; relative airflow; angles of attack and incidence.
2 · The flow Two-dimensional flow, upwash and downwash, streamtubes and dynamic pressure.
3 · The pressure Stagnation point, pressure distribution, pressure gradients and the stall.
4 · Where lift acts Centre of pressure, force coefficients, aerodynamic centre, symmetrical sections, ice.
Chapter 4 · Aerofoils and Subsonic Airflow
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through the lesson, in four parts. First the section itself: its chord, camber, thickness and leading-edge radius, and the three angles pilots so often mix up, namely angle of attack, angle of incidence and pitch attitude. Second, the airflow: how air approaching a wing rises to meet it, speeds up over it and leaves it turned downward. Third, the pressure that this flow creates, how it is spread over the surface, and what happens when the angle of attack becomes too large. And fourth, where the resulting lift actually acts, why that point moves, and the steady nose-down pitching moment that every cambered wing produces. Keep a picture of a wing section in your mind as we go; every slide adds one more label to it.
Part 1 · The section
The parts of an aerofoil section An aerofoil is a shape that produces lift with relatively high efficiency Chord line : straight line joining the centres of curvature of the leading and trailing edgesChord : the distance from leading edge to trailing edge along the chord lineMean camber line : the line halfway between the upper and lower surfacesMaximum thickness : the greatest depth of the section, at right angles to the chord
maximum thickness
mean camber line
chord line
leading edge
trailing edge
chord (c)
NACA 2412, drawn to scale
Chapter 4 · Aerofoils and Subsonic Airflow
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
An aerofoil is simply a shape designed to produce lift efficiently, and a wing is built from slices of it, called sections. The front of the section is the leading edge and the back is the trailing edge. Join the centres of curvature of those two edges with a straight line and you have the chord line; its length is the chord. Now find the points halfway between the upper and lower surfaces all the way along, and join them: that curved line is the mean camber line. The greatest depth of the section, measured at right angles to the chord, is the maximum thickness. Notice that on this section the camber line sits slightly above the chord line, and the upper surface is more curved than the lower. That small asymmetry is what lets the section lift even when the chord points straight into the airflow.
Part 1 · The section
Camber, thickness and leading-edge radius in numbers
leading-edge radius
1.6% of chord
maximum thickness 12% of chord
located 30% aft of the leading edge
maximum camber 2% of chord, 40% aft
mean camber line
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
position along the chord, measured aft of the leading edge
Camber, thickness and their positions are all quoted as a percentage of the chord , measured aft of the leading edge.
Chapter 4 · Aerofoils and Subsonic Airflow
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Designers describe a section with a few numbers, each one a percentage of the chord. This classic section is called two four one two. Its maximum camber, the greatest distance between the mean camber line and the chord line, is two per cent of the chord, located forty per cent of the way back from the leading edge. Its thickness to chord ratio is twelve per cent: the deepest point is twelve per cent of the chord, about thirty per cent aft of the leading edge. The leading-edge radius, the radius of the curve that fits the nose, is about one point six per cent of the chord here. These numbers matter. Thickness and its distribution strongly shape the airflow, and a well-rounded leading edge lets the air flow round the nose much more easily than a sharp one, which delays the breakdown of the flow at high angles of attack.
Part 1 · The section
Positive, zero and negative camber
dashed: chord line · coloured: mean camber line (drawn to scale)
Positive camber Camber line above the chord line. Lifts even at zero angle of attack; the usual wing section.
Symmetrical Camber line and chord line coincide , so there is no camber. No lift at zero angle of attack.
Negative camber Camber line below the chord line. Used where a downward force is wanted, such as some tailplanes.
Chapter 4 · Aerofoils and Subsonic Airflow
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Camber can go three ways. If the mean camber line lies above the chord line, the section has positive camber; this is the normal wing section, and it produces some lift even with the chord pointing straight into the airflow. If the camber line and the chord line lie exactly on top of each other, the section is symmetrical and has no camber at all; it produces no lift at zero angle of attack, and as we will see later, it has no pitching moment either. If the camber line lies below the chord line, the section has negative camber; it naturally produces a downward force, which is why the idea appears on some tailplanes. In each drawing the dashed line is the chord and the coloured line is the mean camber line. In the exam, remember that a symmetrical section is simply one with zero camber.
Part 1 · The airflow
Relative airflow: direction, condition and magnitude Direction : parallel and opposite to the flight path of the centre of gravity; where the nose points is irrelevantCondition : air close to the aircraft but undisturbed by it: its pressure, temperature and speed are unaffectedMagnitude : the speed of the aircraft through the air, the TAS Also called the relative wind or the free stream Air that lacks any of the three qualities is effective airflow
disturbed air near the wing:
effective airflow
flight path (CG)
Relative airflow: undisturbed, magnitude = TAS
parallel and opposite to the flight path
nose points higher:
irrelevant to the airflow
Chapter 4 · Aerofoils and Subsonic Airflow
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Relative airflow, also called the relative wind or the free stream, is the air as the wing sees it, and it has three qualities. Its direction is parallel to the flight path of the aircraft, strictly the path of its centre of gravity, and opposite to it. Where the nose happens to point makes no difference at all. Its condition is undisturbed: it is air close to the aircraft, but not yet affected by it, so its pressure, temperature and speed are the free-stream values. And its magnitude is the true airspeed. In the diagram the wing climbs to the left, and far from it the blue arrows show the relative airflow coming from ahead and parallel to the path. Air near the wing has been disturbed, bent and speeded up. Air that lacks any of the three qualities is called effective airflow, and its angle to the chord is the effective angle of attack.
Part 1 · The angles
Angle of attack is not the pitch attitude
Climb
path +8° · attitude +12° · α = 4°
horizon
α
relative airflow
dark arrow: flight path · dashed: chord line
Level
path +0° · attitude +4° · α = 4°
horizon
α
relative airflow
dark arrow: flight path · dashed: chord line
Descent
path -6° · attitude -2° · α = 4°
horizon
α
relative airflow
dark arrow: flight path · dashed: chord line
Angle of attack (α) : chord line to relative airflow. Pitch attitude : nose relative to the horizon. Same α, three different attitudes.
Chapter 4 · Aerofoils and Subsonic Airflow
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The angle of attack, written alpha and sometimes called aerodynamic incidence, is the angle between the chord line and the relative airflow. It is not the angle between the nose and the horizon; that is the pitch attitude. Look at the three panels. In the climb the flight path rises at eight degrees and the nose is twelve degrees up, so alpha is four degrees. In level flight the path is horizontal and the nose is four degrees up, so alpha is again four. In the descent the path falls at six degrees and the nose is two degrees below the horizon, and alpha is still four. Same angle of attack, three very different attitudes. This is why a wing can stall in any attitude: the stall depends on alpha, which is measured from the airflow, never from the horizon. Always ask which way the air is coming from.
Part 1 · The angles
The angle of incidence is built in Angle of incidence : between the wing root chord line and the longitudinal axis of the aircraftIt is fixed for the wing, chosen by the designer, usually a few degrees It may be variable for the tailplane, for trimming Do not confuse it with angle of attack, which is aerodynamic incidence and changes all the time Chosen so the fuselage is roughly level, and drag low, in the cruise
longitudinal axis
root chord line
angle of incidence
root chord to longitudinal axis
tailplane incidence
may be adjustable
Angle exaggerated for clarity; wings are set at a few degrees.
Chapter 4 · Aerofoils and Subsonic Airflow
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The angle of incidence sounds like angle of attack, but it is a fixed, built-in angle. It is the angle between the chord line at the wing root and the longitudinal axis of the aircraft, and the designer chooses it, usually a few degrees nose up, so that in the cruise the wing is at its efficient angle of attack while the fuselage sits roughly level and makes little drag. You cannot change it in flight. The tailplane is a little different: on many aircraft its incidence is adjustable, and moving the whole tailplane is one way of trimming. In the diagram the angle has been exaggerated so you can see it. Exam trap: the phrase aerodynamic incidence means angle of attack, measured to the airflow, while plain angle of incidence, or rigging incidence, is the fixed angle to the longitudinal axis.
Part 1 · The forces
Lift, drag and the total reaction Total reaction : the resultant of all the aerodynamic forces on the sectionLift : the part of it at 90° to the relative airflow Drag : the part parallel to the relative airflow , in the same direction, opposing the motionCentre of pressure : the point on the chord line through which lift is taken to actLift and drag are defined by the airflow , not by the chord or the upper surface
relative airflow
Lift
at 90° to the
relative airflow
Total reaction
resultant of all the
aerodynamic forces
Drag
parallel to the airflow
centre of pressure
Chapter 4 · Aerofoils and Subsonic Airflow
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
All the pressures and friction forces on the section add up to one resultant, called the total reaction. It is convenient to split it into two parts measured from the relative airflow. Lift is the part at right angles to the relative airflow, and drag is the part parallel to it, acting in the same direction as the airflow, so it opposes the motion. Both act through the centre of pressure, the point on the chord line through which the lift is considered to act. Two exam traps live here. Lift is not perpendicular to the chord line, nor to the upper surface; it is perpendicular to the relative airflow, which is the same as saying perpendicular to the flight path. And drag is parallel to the flight path, not to the longitudinal axis. In this picture the total reaction leans back from the lift by just a few degrees, because the drag is small.
Part 2 · The flow
Thinking in two dimensions first Relative motion Air moving past a stationary wing in a wind tunnel, or a wing moving through still air: the pressure pattern is the same . Only relative velocity matters.
Two-dimensional flow Imagine a wing of infinite span with the same section everywhere: no spanwise pressure difference and no spanwise flow . Every slice behaves alike.
Three-dimensional flow The real flow: the 2D picture modified by spanwise pressure differences , giving tip vortices and induced downwash. That comes in Lesson 6.
Chapter 4 · Aerofoils and Subsonic Airflow
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before we study real wings we simplify. First, relative motion: it makes no difference to the pressures whether air blows past a fixed wing in a wind tunnel or the wing moves through still air. Only the relative velocity matters, so we will switch freely between the two pictures. Second, we imagine a wing of infinite span with exactly the same section all the way along. There is then no pressure difference along the span, so no air flows sideways, and every slice behaves exactly like every other. That idealised flow is called two-dimensional airflow, and it lets us study one section on its own. The real flow round an aircraft is three-dimensional: the two-dimensional pattern is modified by spanwise pressure differences, which create tip vortices and induced downwash. We save that for lesson six.
Part 2 · The flow
Upwash ahead, downwash behind
stagnation point: the flow divides
Upwash
air rises ahead of
the leading edge
Downwash
flow leaves the trailing
edge turned down
streamlines crowd together: faster air, lower pressure
computed potential flow, cambered section at 6°
Chapter 4 · Aerofoils and Subsonic Airflow
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Watch how the air behaves as it meets the section. Well ahead of the leading edge the streamlines already begin to rise, drawn towards the lower pressure on the upper surface. That rising flow is called upwash. At the front the flow divides at the stagnation point, some going over the top and some underneath. Over the upper surface the streamlines crowd closer together, which means the air there is moving faster. Behind the trailing edge the flow leaves turned downward, which is called downwash, and in this ideal two-dimensional picture it then returns to its original direction and state well downstream. The colours in the live picture show local speed: warm colours are faster air, cool colours slower air. These streamlines in the drawing were computed for a real cambered section at six degrees angle of attack.
Part 2 · The flow
Why the air speeds up over the top A streamtube is the channel between two neighbouring streamlines: no air crosses its walls Same mass flow everywhere along it, so where it narrows the air must go faster Faster air has lower static pressure (Bernoulli: total pressure stays constant) Over the top the tubes narrow; underneath they widen slightly Raising the angle of attack narrows the upper tubes further: more acceleration, more lift
Upper streamtube narrows
width × 0.76 → speed × 1.31 → pressure falls
Lower streamtube widens slightly
width × 1.11 → speed × 0.90 → pressure rises
Chapter 4 · Aerofoils and Subsonic Airflow
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does the air go faster over the top? Picture the channel between two neighbouring streamlines. It is called a streamtube, and no air crosses its walls, so the same mass of air passes every point along it each second. Where the tube narrows, the air must speed up, just as in a venturi. And when air speeds up, its static pressure falls, because the total of static and dynamic pressure stays the same. In this computed flow, the shaded tube passing over the upper surface is squeezed to well under its original width, so the air in it speeds up markedly and its pressure drops. The tube passing underneath widens a little, so that air slows slightly and its pressure rises. Increase the angle of attack and the upper tubes are squeezed even more, giving more acceleration, a bigger pressure difference and more lift.
Part 2 · The flow
Dynamic pressure scales every pressure difference At a given angle of attack the pattern of pressure stays the same Its size is set by the dynamic pressure, q = ½ρV² , which the ASI measures as IAS Double q and every pressure difference, and the lift , doubles 100 kt → 141 kt IAS doubles q, because 1.41² ≈ 2 If the static pressure on one side is reduced more than on the other, a pressure differential exists
100 kt IAS · dynamic pressure × 1
141 kt IAS · dynamic pressure × 2
Same angle of attack (4°); arrow length proportional to pressure change
Chapter 4 · Aerofoils and Subsonic Airflow
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Hold the angle of attack constant and change only the speed. The pattern of pressure round the section stays exactly the same shape; what changes is its size, and that is set by the dynamic pressure, half rho V squared, which is what the airspeed indicator measures as indicated airspeed. Because dynamic pressure goes with the square of speed, a modest increase in speed makes a big difference. Going from one hundred to one hundred and forty-one knots indicated doubles the dynamic pressure, since one point four one squared is two, and so it doubles every pressure difference on the section and doubles the lift. Put simply: if the static pressure on one side is reduced more than on the other, a pressure differential exists, and if the dynamic pressure is increased, that differential increases. This is why a faster wing needs less angle of attack for the same lift.
Part 3 · The pressure
The stagnation point Where the flow divides; the local airspeed is zero Pressure there = static + dynamic : the highest positive pressure on the section At about −4° (zero lift for this cambered section) it sits slightly on the upper surface As α increases it moves round the nose to the lower surface The high nose pressure against lower pressure at the tail gives form (pressure) drag
α = -4°
on the upper surface
α = +4°
below the nose
α = +12°
below the nose
Nose close-ups. Red: dividing streamline and stagnation point (computed)
Chapter 4 · Aerofoils and Subsonic Airflow
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
At the front of the section there is one point where the flow divides, some air going over and some under. There the air is brought to rest relative to the wing, so the local speed is zero and the pressure rises to static plus dynamic, the greatest positive pressure anywhere on the section. This is the stagnation point. Its position depends on the angle of attack. For this cambered section the zero-lift angle is about minus four degrees, and there the stagnation point sits slightly on the upper surface. As the angle of attack increases, it moves round the nose and onto the lower surface, and the further you go, the further back underneath it sits. One more consequence: high pressure at the nose and lower pressure towards the trailing edge push the section backwards. That is form drag, also called pressure drag, and it rises with dynamic pressure.
Part 3 · The pressure
How the pressure pattern changes with angle of attack
α = −4°: zero lift
equal suction above and below
α = 0°
cambered section still lifts
α = 4°
suction grows on top
α = 8°
peak moves forward
α = 14°
strong peak near the nose
α = 18°: stalled
upper suction collapses
Orange: pressure below free-stream static (suction). Blue: pressure above it. Computed for a cambered section; arrow lengths compressed.
Chapter 4 · Aerofoils and Subsonic Airflow
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the whole story of lift in six pictures, computed for a cambered section, with orange arrows showing pressure below free-stream static and blue arrows pressure above it. At minus four degrees the reduction in pressure above and below is equal, so there is no lift: this is the zero-lift angle of attack. At zero degrees there is more suction on top than underneath, so this cambered section is already lifting. At four and eight degrees the suction on the upper surface grows strongly and its peak moves forward towards the leading edge, while the pressure underneath rises above static. By fourteen degrees there is an intense suction peak just behind the nose. Notice that most of the lift comes from the upper surface. At eighteen degrees, beyond the critical angle of about sixteen, the flow over the top has separated and the upper suction has collapsed; what lift remains comes mainly from the lower surface.
Part 3 · The pressure
Favourable and adverse pressure gradients A pressure gradient is a change of pressure over distance Favourable : pressure falling in the direction of flow, from the stagnation point to the suction peakAdverse : pressure rising in the direction of flow, from the peak back to the trailing edgeThe higher the angle of attack, the steeper the adverse gradient Beyond about 16° the air can no longer climb it: the flow separates
0.0
0.2
0.4
0.6
0.8
1.0
-1
0
1
2
3
4
position along the chord (x / c)
suction (−Cp) ↑
suction peak
free-stream static
upper surface 4°
upper surface 10°
lower surfaces
adverse gradient: pressure rising
Computed (inviscid) pressure coefficient; suction plotted upward
Chapter 4 · Aerofoils and Subsonic Airflow
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph plots suction along the chord, with suction upward. On the upper surface the pressure falls from the stagnation value, through free-stream static, to a sharp peak near the leading edge. Along that stretch pressure is falling in the direction of flow, which is called a favourable pressure gradient; it helps the air along. From the peak back to the trailing edge the pressure rises again to roughly free-stream static. Pressure rising in the direction of flow is an adverse pressure gradient: the air is being asked to flow uphill against rising pressure, and it slows down. Now compare four degrees with ten. At the higher angle the peak is much taller and closer to the nose, so the adverse gradient behind it is much steeper. The higher the angle of attack, the steeper the gradient, and that is where the stall begins.
Part 3 · The pressure
Beyond the critical angle: separation and the stall Up to about 16° , more α gives more pressure differential and more lift Then the adverse gradient is so steep that the upper flow cannot follow the contour Smooth streamline flow separates and the upper low-pressure area collapses suddenly What lift remains comes from the lower surface This is the stall ; it depends on angle of attack, not speed
separated flow: turbulent eddies
α = 18°, beyond the critical angle
Lower-surface flow still attached; upper suction lost
Chapter 4 · Aerofoils and Subsonic Airflow
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
As we increase the angle of attack, up to about sixteen degrees, the upper surface flow accelerates more and the pressure differential and lift keep growing. But the adverse pressure gradient behind the suction peak also gets steeper. Eventually it is so steep that the air flowing over the top simply cannot follow the contour of the surface. The smooth streamline flow separates, breaking away into a wide region of turbulent eddies, and the low pressure area on top suddenly collapses. Any lift that remains is due to the raised pressure on the lower surface. This condition is the stall. Watch the live picture: the angle increases, the lift arrow grows, and then, as the flow separates, the lift falls away. Remember that the stall happens at a critical angle of attack, whatever the speed or attitude. We will look at the stall in detail in a later lesson.
Part 4 · Where lift acts
The centre of pressure moves forward Every part of the surface contributes to lift; the centre of pressure is where the total is effectively concentrated Its position depends on camber and on the lift coefficient , that is the angle of attack Cambered section: as α increases the suction peak moves forward, so the CP moves forward At the same time the lift grows At the stall lift falls abruptly and the CP moves back
α = 2°
CP 40% chord
α = 8°
CP 33% chord
α = 14°
CP 31% chord
Lift grows and its line of action moves forward
Chapter 4 · Aerofoils and Subsonic Airflow
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every bit of the surface contributes to the lift, but we can replace all those small pressures with one force acting at one point. That point, on the chord line, is the centre of pressure, the place where the distributed lift is effectively concentrated. Where it lies depends on the camber of the section and on its lift coefficient, which for a given section means the angle of attack. On a cambered section, as the angle of attack increases, the upper suction peak moves forward, as we saw in the pressure pictures, so the centre of pressure moves forward too. At the same time the lift grows. In the live picture watch the dot slide towards the leading edge while the green arrow lengthens. This continues right up to the stall, when the lift drops abruptly and the centre of pressure generally moves back along the chord.
Part 4 · Where lift acts
Centre of pressure position against angle of attack
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0°
4°
8°
12°
16°
20°
angle of attack
aerodynamic centre 25%
CP furthest forward just before the stall (C L max)
after the stall the CP moves back
small lift: CP well aft
as α rises the CP moves forward
leading edge
trailing edge
CP position, fraction of chord aft of the leading edge
The CP is at its most forward position just before the stall, at CL max . (Green: computed; red dashed: typical behaviour after the stall.)
Chapter 4 · Aerofoils and Subsonic Airflow
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the movement of the centre of pressure as a graph, with its position along the chord across the page and angle of attack up the page. The green line was computed for a cambered section. At small angles, when the lift is small, the centre of pressure is well aft; near the zero-lift angle it runs off towards the trailing edge and beyond, which is a sign that at zero lift there is no single point where the force acts, only a pure pitching moment. As the angle of attack rises, the centre of pressure moves steadily forward, approaching the quarter chord but never quite reaching it. It is furthest forward just before the stall, at C L max, at about sixteen degrees. After the stall it generally moves back, shown by the red dashed line. In the exam: for a cambered section, the centre of pressure moves forward as alpha increases.
Part 4 · Where lift acts
Force coefficients: one number for any size and speed A coefficient is a dimensionless number expressing degree of magnitude C L = lift per unit wing area ÷ dynamic pressure; C D is the same for dragIndependent of area, density and speed: a common yardstick for any aircraft Depends only on the shape of the section and the angle of attack Those two set the pressure distribution, so they set the coefficient
C L = L ÷ ( q × S )
lift per square metre ÷ dynamic pressure
Light trainer
lift 9 800 N · wing 16 m² · 90 kt at sea level
q = 1313 Pa → C L = 0.47
Jet transport
lift 588 600 N · wing 105 m² · 230 kt at sea level
q = 8575 Pa → C L = 0.65
Huge difference in force, similar coefficient: C L depends on shape and α
Chapter 4 · Aerofoils and Subsonic Airflow
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
To compare a small trainer with a large jet we need a number that does not depend on size or speed. That is a force coefficient. The lift coefficient, C L, is the lift per square metre of wing divided by the dynamic pressure; in other words, the average pressure difference the wing creates, compared with the dynamic pressure of the airstream. The drag coefficient, C D, is built the same way from the drag. Because area, density and speed have been divided out, the coefficient depends only on the things that shape the pressure distribution: the shape of the section and the angle of attack. Look at the two examples. A trainer weighing under ten thousand newtons and an airliner of nearly six hundred thousand newtons carry wildly different forces, yet at sensible speeds both lift coefficients come out at similar values, well under one. We will use the full lift formula in the next lesson.
Part 4 · Pitching moment
The aerodynamic centre: where the moment stays constant
AC 25%
C L 0.4
acting at 37.5% chord
arm 12.5% c
nose down
Low angle of attack
moment about AC = 0.4 × 0.125 = 0.050, nose down
in units of q × S × c
AC 25%
C L 1.0
acting at 30.0% chord
arm 5.0% c
nose down
Higher angle of attack
moment about AC = 1.0 × 0.050 = 0.050, nose down
in units of q × S × c
Below about M 0.4 the aerodynamic centre is at 25% chord for any section. About it a cambered section has a constant nose-down pitching moment.
Chapter 4 · Aerofoils and Subsonic Airflow
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The pressure distribution gives a pitching moment as well as a force, and there are two ways to describe it. One is a changing lift acting through a moving centre of pressure. The simpler way uses a fixed point called the aerodynamic centre. It is defined as the point where all changes in lift effectively take place, and the point about which the pitching moment stays constant at normal angles of attack. Below about Mach zero point four it sits at twenty-five per cent of the chord, whatever the section. Here is why the moment stays constant. At low angle of attack, a lift coefficient of zero point four acts at thirty-seven and a half per cent chord, an arm of twelve and a half per cent: moment zero point zero five. At higher angle, one point zero acts at thirty per cent, an arm of five per cent: again zero point zero five, nose down. More lift, shorter arm, same moment.
Part 4 · Pitching moment
Symmetrical sections: a CP that stays put At zero α the upper and lower forces are equal and act at the same point : no lift As α increases, upper suction grows and lower suction shrinks: lift appears The CP does not move ; it stays at the aerodynamic centre, 25% chord So the pitching moment about the AC is zero at normal angles of attack A big advantage for tailplanes, fins and aerobatic or high-speed designs
Symmetrical section, α = 0°
upper and lower forces equal: no lift
CP stays at the AC (25%)
Symmetrical section, α = 6°
more suction on top: lift, but no moment about the AC
Chapter 4 · Aerofoils and Subsonic Airflow
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
A symmetrical section behaves differently. At zero angle of attack the pressure patterns above and below are mirror images, so the upward and downward forces are equal and act at the same point, and there is no lift at all. As the angle of attack increases, the suction on top grows and the suction underneath shrinks, so lift appears. But the shape of the distribution changes in such a way that the lift keeps acting at the same place, the quarter chord, which is the aerodynamic centre. So for a symmetrical section the centre of pressure does not move with angle of attack, within the normal range, and the pitching moment about the aerodynamic centre is zero. That is one of its big advantages. It explains why tailplanes, fins and many aerobatic aircraft use symmetrical sections, where a steady pitching moment would be unwelcome.
Part 4 · Contamination
Why the leading edge must be clean The strong acceleration round the nose depends on its accurately made shape Ice above all, but also frost, snow, dirt, dents and even water drops, can seriously disrupt itResult: much less lift ; with enough ice, lift can be lost almost entirely at normal angles Ice also adds frontal area, so form drag increases The loss of lift is the more serious effect
ice horns
flow cannot follow the spoiled nose:
early separation, much less lift
The front 20% of the chord is the critical area
Chapter 4 · Aerofoils and Subsonic Airflow
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Remember where most of the lift comes from: the strong acceleration of the air round the nose and over the front of the upper surface. That depends on the accurately manufactured shape of the leading portion of the wing. Anything that spoils it can seriously disrupt the acceleration. Ice is the worst offender, especially horn ice like this, but frost, snow, dirt, dents and even water droplets do harm too. The air cannot accelerate smoothly round the spoiled nose, the flow separates early, and the lift is greatly reduced. With enough ice, lift can be lost almost entirely, even at normal angles of attack. The ice also increases the frontal area, so form drag goes up. Of the two effects, the loss of lift is the greater. That is why the leading portion, roughly the front twenty per cent of the chord, must be clean before flight.
Summary
What to take into the exam Terms Chord line joins the LE and TE centres of curvature. Camber line is halfway between surfaces. Thickness and camber in % of chord.
Relative airflow Parallel and opposite to the flight path, undisturbed, magnitude TAS. Otherwise it is effective airflow.
Angles α: chord to relative airflow. Incidence: root chord to longitudinal axis, fixed. Attitude: to the horizon.
Forces Lift ⟂ relative airflow, drag ∥ to it, total reaction is their resultant, acting at the CP.
Pressure Lift is mainly upper-surface suction. Doubling q doubles it. More α, more differential, up to about 16°.
Stagnation Speed zero, pressure static + dynamic, highest. Moves from upper surface round to lower surface as α rises.
CP and AC Cambered: CP moves forward with α, most forward just before C L max. AC at 25%: constant nose-down moment.
Symmetrical and ice Symmetrical: no lift at 0°, CP fixed at AC, zero moment. Leading-edge ice: big loss of lift, more form drag.
Chapter 4 · Aerofoils and Subsonic Airflow
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the key points. The chord line joins the centres of curvature of the leading and trailing edges, the mean camber line runs halfway between the surfaces, and camber and thickness are quoted as percentages of the chord. The relative airflow is parallel and opposite to the flight path, undisturbed, with a magnitude equal to the true airspeed. Angle of attack is chord to relative airflow, angle of incidence is root chord to longitudinal axis and is fixed, and attitude is measured to the horizon. Lift is at right angles to the relative airflow, drag parallel to it. Most lift comes from upper-surface suction; doubling dynamic pressure doubles it, and more angle of attack increases it up to about sixteen degrees. For a cambered section the centre of pressure moves forward as alpha increases, while the moment about the aerodynamic centre at the quarter chord stays constant and nose down. Symmetrical sections have a fixed centre of pressure and no moment. Keep the leading edge clean.