Principles of Flight · Chapter 3
Continuity and Bernoulli Why air speeds up through a narrowing, why its pressure falls when it does, and how streamlines and streamtubes let us see it happen round a wing.
faster at the throat, lower static pressure © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to chapter three. Two simple ideas sit underneath almost everything in aerodynamics. The first is continuity: air cannot pile up or vanish, so where a flow is squeezed into a smaller area it must speed up. The second is Bernoulli’s theorem: when the air speeds up its static pressure falls, and when it slows down the pressure rises again. Put the two together, add the idea of streamlines and streamtubes, and you can see how a wing shape produces a pressure difference, and so a force.
Chapter 3 roadmap
Two laws that explain the pressure round a wing 1 · Conservation Mass and energy are neither created nor destroyed, only changed in form.
2 · Continuity Mass flow ρ A V = constant ; at low speed A V = constant .
3 · Bernoulli p + ½ ρ V² = constant : faster flow, lower static pressure.
4 · Total pressure Static + dynamic = total, stagnation or pitot pressure.
5 · Streamlines Paths of the air; their spacing shows speed and pressure. Streamtubes.
6 · To the wing Faster over the top, lower pressure, a net force .
Chapter 3 · Continuity and Bernoulli
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter three is short in the syllabus, but it is the foundation for everything that follows. We start with the idea that mass and energy are conserved. From mass conservation comes the principle of continuity: the mass of air flowing past any section of a tube each second is the same, so where the tube narrows the air must speed up. From energy conservation comes Bernoulli’s theorem: static pressure plus dynamic pressure stays constant, so where the air speeds up its static pressure falls. We then look at total pressure and the stagnation point, at streamlines and streamtubes, and finally put it all together to see how a wing’s shape creates a pressure difference, and therefore a force.
Part 1 · Conservation
Mass and energy cannot be created or destroyed A fundamental law: energy and mass can be neither created nor destroyed, only changed in form This is the basis of the principle of continuity Picture a steady, streamline flow of air through a tube with a narrower middle Whatever mass enters each second must leave each second Air cannot pile up in the tube or escape through its walls in: 63.7 kg every second out: 63.7 kg every second Nothing is created, nothing is lost Mass in = mass out (no leaks through the walls) Energy in = energy out (only its form changes) 1 m² inlet, 52 m/s, ρ = 1.225 kg/m³
Chapter 3 · Continuity and Bernoulli
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
One of the fundamental laws of nature is that energy and mass can be neither created nor destroyed; they can only be changed from one form into another. This simple statement is the starting point for this whole chapter, and the exam often quotes it word for word and asks which principle it describes: the answer is the principle of continuity. To see what it means for airflow, imagine a smooth, steady flow of air through a tube that is wide at each end and narrow in the middle. Every second, a certain mass of air enters the tube. Because no air can be created or destroyed inside, and none can leak through the walls, exactly the same mass must leave every second. The air cannot pile up somewhere in the middle. That is all continuity is, but its consequences are powerful.
Mass flow
Mass flow = density × area × velocity Mass flow : the mass of air passing a section each second (kg/s)In one second the air moves V metres, sweeping a volume A × V Multiply by density: mass flow = ρ × A × V 1 m² at 52 m/s and 1.225 kg/m³: 63.7 kg/s In a steady flow it is the same at every section of the tube Mass flow = ρ × A × V V metres in 1 second A volume A × V mass per second = density × volume per second 1.225 × 1 × 52 = 63.7 kg/s
Chapter 3 · Continuity and Bernoulli
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Mass flow is the mass of air passing through a cross-section every second, measured in kilograms per second. Here is how to work it out. In one second, the air moves forward V metres. So the slab of air that passes the section in that second has a volume equal to the area A times the distance V. Multiply that volume by the density, rho, and you have the mass. So mass flow equals rho times A times V. For example, a tube with a cross-section of one square metre, carrying air at fifty-two metres per second, about one hundred knots, at sea level density, passes one point two two five times one times fifty-two: about sixty-three point seven kilograms of air every second. In a steady flow, that number is the same at every section along the tube.
Part 2 · The equation of continuity
Narrower tube, faster air Equation of continuity: A × V × ρ = constant Air is compressible, so pressure changes can change its density Below about M 0.4 the density change is small enough to ignore So at low speed: A × V = constant , or V = constant ÷ A Area down, speed up ; area up, speed downA = 1 m² V = 52 m/s A = ½ m² V = 104 m/s A = 1 m² V = 52 m/s A × V = constant area halved → speed doubled
Chapter 3 · Continuity and Bernoulli
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the mass flow must be the same everywhere along the tube, area times velocity times density is a constant. That is the equation of continuity. Air is compressible, so in principle a change of pressure could change its density too. But at low subsonic speeds, below about Mach zero point four, the density changes are so small that we can ignore them. Then the equation simplifies to area times velocity equals a constant. In other words, velocity equals a constant divided by area. Watch the particles in the tube. Where it is wide, they move slowly. As the tube narrows, they speed up, and they are fastest at the throat, the narrowest point. Where it widens again, they slow back down. So reducing the cross-sectional area increases the velocity, and increasing the area reduces it. This lets aerodynamicists predict the velocity changes round any shape.
Worked example
Halve the area, double the speed A = 1 m² V = 52 m/s (100 kt) ρAV = 63.7 kg/s A = ½ m² V = 104 m/s (200 kt) ρAV = 63.7 kg/s A = 1 m² V = 52 m/s (100 kt) ρAV = 63.7 kg/s Halve the area → double the speed. A × V = constant (below about M 0.4)
Chapter 3 · Continuity and Bernoulli
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put numbers on the tube. At the inlet the area is one square metre and the air moves at fifty-two metres per second, about one hundred knots. At the throat the area is half a square metre. Area times velocity must stay the same: one times fifty-two is fifty-two, so at the throat the velocity must be fifty-two divided by a half, which is one hundred and four metres per second, about two hundred knots. At the outlet the area is back to one square metre, so the speed is back to fifty-two. At every section the mass flow, rho times A times V, is sixty-three point seven kilograms per second. Notice that one hundred and four metres per second is still well below Mach zero point four, so ignoring the density change is reasonable. Halve the area, double the speed. That is continuity in one line.
The low-speed simplification
Why we may ignore density changes below M 0.4 Pressure changes in a flow do change the density a little The faster the flow, the bigger the pressure change, and the bigger the density change Bring air at M 0.3 to rest: density rises about 4–5% ; at M 0.4 , about 8% For understanding principles, below M 0.4 we treat air as incompressible At higher Mach numbers compressibility must be included (chapter on high-speed flight) 0% 10% 20% 30% 40% 50% 60% 70% 0.0 0.2 0.4 0.6 0.8 1.0 M 0.3: 5% M 0.4: 8% treat as incompressible compressibility must be included Mach number of the flow density rise when the air is brought to rest
Chapter 3 · Continuity and Bernoulli
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why can we pretend that air, a gas, has a constant density? Whenever the flow speeds up or slows down its pressure changes, and a pressure change does squeeze or expand the air a little. The faster the flow, the bigger the pressure changes and so the bigger the density changes. The graph, computed from the gas laws, shows the largest possible change: the density rise when moving air is brought completely to rest. At Mach zero point three it is about four to five per cent, and at Mach zero point four about eight per cent. Those are small enough that, for understanding the principles of low-speed flight, we treat the air as incompressible below about Mach zero point four. That is the rule the exam expects. Above that, the density changes grow quickly and must be taken into account, which is the subject of the high-speed chapters.
Part 3 · Energy in a moving fluid
Pressure energy and kinetic energy A moving fluid carries energy in two main forms here: pressure and kinetic Static pressure is pressure energy per unit volume (N/m² = J/m³) Dynamic pressure ½ ρ V² is kinetic energy per unit volume Energy is conserved, so if one rises the other must fall At the throat KE is four times greater, so static pressure is lower Energy in each cubic metre of air Inlet, 52 m/s pressure 101 325 KE 1 656 Throat, 104 m/s pressure 96 356 KE 6 625 total 102 981 N/m² (J/m³) everywhere axis starts at 94 000 to show the change
Chapter 3 · Continuity and Bernoulli
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now energy. In the airflow we are considering, each cubic metre of air carries energy in two forms. One is pressure energy: static pressure, measured in newtons per square metre, is the same thing as joules per cubic metre. The other is kinetic energy: half rho V squared, the dynamic pressure, is the kinetic energy in each cubic metre of air. Because energy cannot be created or destroyed, the total of these two must stay the same along the flow. So when the air speeds up through the throat and its kinetic energy rises, its pressure energy must fall by the same amount. The bars show it with real numbers. At the inlet, a big pressure part and a small kinetic part. At the throat the kinetic part is four times bigger, and the pressure part is smaller, but the total is identical.
Bernoulli’s theorem
p + ½ ρ V² = constant Bernoulli’s theorem : in the steady flow of an ideal fluid, the sum of pressure and kinetic energy per unit volume is constantAn ideal fluid is incompressible and has no viscosity p + ½ ρ V² = constant along a streamlineSpeed up: dynamic pressure rises, static pressure falls Slow down: dynamic pressure falls, static pressure rises p + ½ ρ V² = constant static pressure dynamic pressure (KE per m³) total Speed rises ↑ V ↑ q ↓ p Speed falls ↓ V ↓ q ↑ p Ideal fluid: incompressible and no viscosity Steady flow along a streamline
Chapter 3 · Continuity and Bernoulli
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
That energy argument is Bernoulli’s theorem. In the steady flow of an ideal fluid, the sum of the pressure and the kinetic energy per unit volume remains constant. An ideal fluid is one that is incompressible and has no viscosity; air at low speed comes close enough for our purposes. In symbols, static pressure plus half rho V squared equals a constant, along a streamline. Read it in both directions. If the flow speeds up, its dynamic pressure increases and its static pressure must decrease. If the flow slows down, its dynamic pressure decreases and its static pressure must increase. The exam likes to write this as pressure plus kinetic energy is constant, and asks which law that is: Bernoulli. And watch for distractors that say the static and dynamic pressure both increase together. They cannot, because their sum is fixed.
Seeing it in a venturi
Fast at the throat, low pressure at the throat total pressure 102 981 Pa static at throat 96 356 Pa static 101 325 Pa dynamic 6 625 Pa dynamic 1 656 Pressure along the tube (scale starts at 95 000 Pa); orange gap = dynamic pressure
Chapter 3 · Continuity and Bernoulli
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
A tube with a narrow throat is called a venturi, and it shows both laws working together. Continuity sets the speed: slow at the inlet, fastest at the throat, slow again at the outlet. Bernoulli sets the pressure. The three gauge columns measure the static pressure. At the inlet the static pressure is high. At the throat, where the air is fastest, the static pressure is lowest, so the column there is shortest. At the outlet the air has slowed down again and the pressure recovers to its original value. The graph shows the same thing calculated with numbers. The total pressure line stays flat all the way along. The static pressure dips at the throat, and the gap between the two lines, the dynamic pressure, is largest there. Faster air always means lower static pressure, as long as the total stays constant.
Worked example
Bernoulli with numbers Air at sea level: static pressure 101 325 N/m² , density 1.225 kg/m³ . The throat has half the area of the inlet.
Inlet Throat Outlet Speed 52 m/s (100 kt) 104 m/s (200 kt) 52 m/s (100 kt) Dynamic pressure ½ ρ V² 1 656 N/m² 6 625 N/m² (×4)1 656 N/m² Static pressure p 101 325 N/m² 96 356 N/m² 101 325 N/m² Total pressure p + ½ ρ V² 102 981 N/m² 102 981 N/m² 102 981 N/m² Mass flow ρ A V 63.7 kg/s 63.7 kg/s 63.7 kg/s
Speed ×2 → dynamic pressure ×4, and static pressure falls by exactly that increase (4 969 N/m²). Total, stagnation and pitot pressure are three names for the same constant.
Chapter 3 · Continuity and Bernoulli
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the numbers in a table. Start at the inlet: static pressure one hundred and one thousand three hundred and twenty-five newtons per square metre, and air moving at fifty-two metres per second, which gives a dynamic pressure of one thousand six hundred and fifty-six. The total is one hundred and two thousand nine hundred and eighty-one. At the throat the speed has doubled to one hundred and four metres per second, so the dynamic pressure has risen four times, to six thousand six hundred and twenty-five. The total must stay the same, so the static pressure has fallen to ninety-six thousand three hundred and fifty-six. At the outlet everything returns to the inlet values. The mass flow is the same throughout. And notice the bottom line of Bernoulli: static plus dynamic pressure is a constant, which you can call total pressure, stagnation pressure or pitot pressure.
Total pressure
The stagnation point and total pressure Where the flow meets a body, it divides at the stagnation point There the air is brought to rest relative to the surface: V = 0 All its dynamic pressure becomes static pressure: pstag = p + ½ ρ V² This is the total , stagnation or pitot pressure: the highest pressure in the flow A pitot tube is a stagnation point you can measure Where the air stops, pressure is highest stagnation point V = 0, p = p + ½ ρ V² Total = stagnation = pitot pressure static + dynamic, measured where the air is brought to rest
Chapter 3 · Continuity and Bernoulli
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Whenever the airflow meets a body, a wing, a fuselage or a pitot tube, it has to divide, some going one way and some the other. Right at the dividing point, the stagnation point, the air is brought to rest relative to the surface. Its speed is zero, so its dynamic pressure is zero, and Bernoulli tells us that all of that dynamic pressure has been turned into static pressure. So the pressure at the stagnation point is the free-stream static pressure plus half rho V squared: the total pressure. It is the highest pressure anywhere in the flow. That is why total pressure is also called stagnation pressure. And a pitot tube is simply a stagnation point you can measure: the air inside it is brought to rest, so it senses pitot pressure, the same thing again. Watch the colours in the scene: the slowest air, at the nose, is where the pressure is highest.
Part 4 · Streamlines
Streamlines show the speed A streamline is the path traced by a particle of air in a steady flow Streamlines cannot cross each other Closer together : faster flow, lower static pressureFurther apart : slower flow, higher static pressureBetween two streamlines the mass flow is constant, so spacing works like the walls of a tube close together: fast, low p wide apart: slower, higher p computed potential flow
Chapter 3 · Continuity and Bernoulli
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
A streamline is the path traced by a particle of air in a steady flow. Streamlines can never cross, because a particle of air cannot be in two places or moving in two directions at once. When we draw a set of them, their spacing tells us about the speed. The reason is continuity: between any two neighbouring streamlines the same mass of air flows every second, so where they squeeze closer together the air must be moving faster, and where they spread apart it must be moving more slowly. Then Bernoulli tells us the rest: where they are close together the static pressure is low, and where they are far apart it is high. The drawing shows real, calculated streamlines round a cylinder. They bunch together over the top and bottom, the fast, low-pressure regions, and spread out in front and behind.
Reading a flow pattern
Converging and diverging streamlines CONVERGING accelerating · static pressure falling DIVERGING decelerating · static pressure rising closest spacing: highest speed, lowest static pressure Converging streamlines: accelerating flow, falling static pressure. Diverging : decelerating flow, rising static pressure.
Chapter 3 · Continuity and Bernoulli
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
When streamlines converge, getting closer together in the direction of flow, the air is accelerating and its static pressure is falling. When they diverge, spreading apart, the air is decelerating and its static pressure is rising. Where they are closest, the speed is highest and the static pressure lowest. This gives you a quick way to read any flow picture, whether it is a venturi, a wing section or the flow round a fuselage. A classic exam question lists four statements: close streamlines mean lower static pressure; close streamlines mean higher speed; converging streamlines mean accelerating flow and falling pressure; diverging streamlines mean decelerating flow and rising pressure. All four are true. The trap is to think that crowded lines mean high pressure, because they look crowded. In fact they mean fast flow and low pressure.
The streamtube
An imaginary tube made of streamlines A streamtube is an imaginary tube whose walls are streamlines There is no flow into or out of it through its walls, only along it So continuity and Bernoulli apply inside it, just as in a real tube It lets us picture the flow round an aerofoil as flow in tubes It is a concept to aid understanding, not a physical part a streamtube: a "pipe" whose walls are streamlines No flow crosses the walls; flow only along the tube Narrower tube: faster flow (continuity applies inside)
Chapter 3 · Continuity and Bernoulli
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
If you take a ring of streamlines and imagine them as the walls of a pipe, you have a streamtube. Because the walls are streamlines, and streamlines cannot be crossed, no air flows into or out of the streamtube through its walls; air only flows along it. That means the tube behaves exactly like the solid venturi we have been studying: continuity and Bernoulli apply inside it. Where the streamtube narrows, the flow speeds up and its static pressure falls. With this idea we can picture the air flowing round a wing as a set of streamtubes, some squeezed over the upper surface, some passing underneath. Be careful with one exam distractor: streamtubes are not manufactured in different sizes to fit different wings. A streamtube is purely an imaginary tube, a concept to help us understand how the aerodynamic force is generated.
Part 5 · Towards lift
The aerofoil: a venturi with one wall The tubes only demonstrate the laws; they do not fly an aeroplane A specially shaped body, an aerofoil , does the job Streamtubes over the upper surface are squeezed , so the air there is faster Faster flow on top: lower static pressure than underneath The pressure difference acts over the area: a force towards the lower pressure , mostly upwards upper surface: faster, lower static pressure lower surface: slower, higher static pressure lift
Chapter 3 · Continuity and Bernoulli
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The tubes we have used are only there to demonstrate the two laws; they will not lift an aeroplane. For that we need a specially shaped body, an aerofoil. Look at the flow over the section in the scene. The streamtubes passing over the upper surface are squeezed together, rather like the top half of a venturi, so the air there speeds up. Below the section the flow is slower. By Bernoulli, faster air on top means lower static pressure on top, and the higher pressure underneath pushes up. A pressure difference acting over an area gives a force, and that force acts towards the lower pressure. The larger the area, the bigger the force. So by harnessing continuity and Bernoulli, an aerofoil produces an aerodynamic force. Later chapters show how the angle of attack and camber control it, and add the other side of the story, Newton’s third law and the downwash.
Worked example
Force = pressure difference × area How big a pressure difference does a light aircraft need? Weight W = 1 000 kg × 9.81 = 9 810 N Wing area S = 16 m² Pressure difference needed Δp = W ÷ S = 9 810 ÷ 16 ≈ 613 N/m² Compared with static pressure 613 ÷ 101 325 ≈ 0.6% Force = pressure difference × area, acting towards the LOWER pressure
Chapter 3 · Continuity and Bernoulli
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
How big does the pressure difference across a wing need to be? Take a light aircraft with a mass of one thousand kilograms. Its weight is nine thousand eight hundred and ten newtons. Suppose its wing area is sixteen square metres. Force equals pressure difference times area, so the average pressure difference needed is the weight divided by the area: about six hundred and thirteen newtons per square metre. Compare that with the static pressure at sea level, over one hundred thousand newtons per square metre. The difference is only about zero point six of one per cent. So a wing does not need dramatic pressures; a small difference over a large area is enough. And remember the direction: if the pressure on one side of a surface is lower than on the other, the force acts towards the lower pressure. That is a favourite exam question, with the opposite answer as a distractor.
Venturi and Bernoulli at work
Where else you meet these laws Pitot tube Air brought to rest inside it: senses total pressure; static from a vent; the difference is q.
Carburettor The venturi lowers pressure to draw in fuel; the pressure and temperature drop can cause carb icing .
Venturi suction A venturi on the fuselage of older light aircraft creates suction to drive gyro instruments .
Wind tunnel The working section is a throat : high speed from a modest fan, with pressure recovered downstream.
Stagnation point At the leading edge the air stops: highest pressure on the section.
Upper surface Squeezed streamtubes: fast, low pressure , the main source of lift.
Static vent Must be in a surface parallel to undisturbed flow, or local speed changes upset it.
Between buildings Wind speeds up through gaps (continuity): gusty, low-pressure corridors near hangars.
Chapter 3 · Continuity and Bernoulli
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
These two laws turn up all over aviation. The pitot tube is a stagnation point: the air inside is brought to rest, so it senses total pressure, and subtracting static pressure from a vent leaves dynamic pressure for the airspeed indicator. The carburettor uses a venturi: the low pressure at the throat draws fuel in, and the drop in pressure and temperature is the reason carburettor icing can occur even on a warm day. Many older light aircraft used a venturi on the side of the fuselage to create suction for the gyro instruments. A wind tunnel works like a big venturi, with the model in the throat. On a wing, the stagnation point at the leading edge is the highest pressure on the section and the squeezed flow over the top is the lowest. Static vents must sit where the local flow speed is undisturbed. And wind speeding up between hangars is continuity in action.
Know the limits
When the simple laws apply Steady flow The pattern does not change with time. Gusts and separated, eddying flow are not steady.
Low speed (below M 0.4) Density treated as constant , so A V = constant . Faster than that, use ρ A V and allow for compressibility.
Ideal fluid Bernoulli assumes no viscosity . Real air has a little, which creates the boundary layer and skin friction.
Along a streamline p + ½ ρ V² is constant along a streamline outside the boundary layer.
Energy forms Heat and height changes are ignored; only pressure and kinetic energy are traded.
Not the whole story Bernoulli explains the pressure pattern; Newton’s third law and downwash describe the same lift from another angle.
Chapter 3 · Continuity and Bernoulli
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every law has its conditions, and the examiner expects you to know these ones. Bernoulli applies to steady flow, where the flow pattern does not change with time. The simple form of continuity, area times velocity is constant, applies only at low speed, below about Mach zero point four, where we can treat the density as constant; at higher speeds we must use the full form with density in it. Bernoulli’s theorem is stated for an ideal fluid, incompressible and without viscosity. Real air does have a little viscosity, which is what creates the boundary layer and skin friction drag, so inside the boundary layer the simple law no longer holds. We are also ignoring changes in height and heat, which are tiny for air flowing round a wing. Finally, Bernoulli is not the whole story of lift: it explains the pressures, while Newton’s third law describes the same lift as air pushed downwards.
Exam focus
Classic traps in this chapter Area reduced Mass flow stays constant and velocity increases . Static pressure decreases , not increases.
Velocity increased KE up, dynamic pressure up, static pressure down . Never both up together.
Below M 0.4 What is insignificant is the change in density caused by pressure changes.
Continuity wording "Energy and mass can be neither created nor destroyed" is the principle of continuity .
Pressure plus KE "Pressure plus kinetic energy is constant" is Bernoulli’s theorem .
Streamtubes Imaginary; no flow through the walls. Not made in sizes to fit a wing!
Chapter 3 · Continuity and Bernoulli
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us run through the classic traps. If the area of a flow is reduced, the mass flow stays constant and the velocity increases; any option saying the velocity stays constant, or that the static pressure increases, is wrong. If the velocity increases, the kinetic energy and dynamic pressure increase and the static pressure decreases; they never both go up together. Below Mach zero point four, what becomes insignificant is the change in density caused by the pressure changes. The statement that energy and mass can neither be created nor destroyed is the principle of continuity, while pressure plus kinetic energy is constant is Bernoulli’s theorem. Continuity does not say that air gets denser when it accelerates; at low speed density is treated as constant. And streamtubes are imaginary, with no flow through their walls; they are certainly not manufactured to match a wing span.
Summary
What to take into the exam Conservation Mass and energy are neither created nor destroyed, only changed in form.
Continuity ρ A V = constant (kg/s). Below M 0.4: A V = constant. Area down, speed up.
Bernoulli Steady ideal flow: p + ½ ρ V² = constant. Speed up, static pressure down.
Total pressure Static + dynamic = total = stagnation = pitot pressure. Constant along the flow.
Stagnation point Flow divides, V = 0, pressure = total: the highest in the flow.
Streamlines Never cross. Close: fast, low p. Converging: accelerating. Diverging: decelerating, p rising.
Streamtube Imaginary tube of streamlines; no flow through its walls.
Force Faster flow over the top: lower pressure. Force = Δp × area, towards the lower pressure.
Chapter 3 · Continuity and Bernoulli
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is chapter three on one page. Mass and energy are neither created nor destroyed. Continuity says the mass flow, rho A V, is constant, and below about Mach zero point four, A times V is constant, so if the area falls the speed rises. Bernoulli says that in steady flow of an ideal fluid, static pressure plus dynamic pressure is constant, so if the speed rises the static pressure falls, and if the speed falls the pressure recovers. Their sum is the total pressure, also called stagnation or pitot pressure. At the stagnation point the air stops and the pressure is the highest in the flow. Streamlines never cross; close together means fast and low pressure, converging means accelerating, diverging means slowing down with rising pressure. A streamtube is an imaginary tube of streamlines with no flow through its walls. And faster flow over an aerofoil gives lower pressure on top, and a force towards the lower pressure.