Principles of Flight · Chapter 14
Airframe Contamination Frost, ice, snow, rain and age: what they do to lift, drag, the stall, the tailplane, the controls and the instruments.
ice horns
separated flow
supercooled droplets
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to airframe contamination. A wing is designed with a smooth, precise shape, and almost anything that sits on it spoils that shape. In this lesson we look at frost, the three kinds of ice, snow, heavy rain and plain old age, and at what each does to lift, drag, weight and the stall. You will see why a thin layer of frost can stop an aircraft flying away from the runway, why an iced tailplane can pitch the nose down when you select flap, and which stall cues you can still trust when ice is on the wing.
Roadmap
Anything on the wing changes how it flies 1 · What forms Frost, clear ice, rime ice, rain ice, snow, water and the wear of age.
2 · Aerodynamic effects Profile, roughness, weight: C L max, drag, stall angle and speed.
3 · Stalls and control Wing stall and tailplane stall, controls, propellers and instruments.
4 · Prevention The clean aircraft, de-icing and anti-icing, heavy rain, ageing.
Chapter 14 · Airframe Contamination
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson is about anything that settles on the airframe and spoils its carefully designed surface. First, what can form: frost, three kinds of ice, snow, water, and the gradual wear of age. Second, the aerodynamic effects. Every contaminant works through just three things, the shape of the profile, the roughness of the surface and the weight of the aircraft, and those change C L max, drag, the stalling angle and the stalling speed. Third, stalls and control: an iced wing and an iced tailplane stall in very different ways, and we will look at controls, propellers and instruments too. Finally, prevention: the clean aircraft concept, ground de-icing, flying in heavy rain, and how an ageing airframe slowly costs more fuel.
Part 1 · What forms
Contamination: on the ground and in flight The airframe can be contaminated by frost, ice, snow or water , on the ground or in flight Icing needs moisture (high relative humidity, visible moisture) and a low temperature Ice: clear (glaze) , rime and rain ice Ice builds first on the leading edges of wings, tailplane, struts and propellers Over the years, ageing adds scratches, dents, repairs and dirt
Ice on the leading edge
clear, rime or rain ice
Frost: rough crystals
Snow and slush
Water film in heavy rain
Ageing: scratches, dents, repairs, dirt, grease
On the ground or in flight, all of them change
the shape, the roughness or the weight.
Chapter 14 · Airframe Contamination
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The airframe can be contaminated by frost, ice, snow or water, either while it stands on the ground or while it is flying. The weather that produces icing is covered in meteorology; here we care about what the deposit does to the aircraft. Icing needs two things together: moisture, meaning high relative humidity or visible moisture such as cloud, rain or fog, and a low temperature. That combination is the exam answer to when icing conditions exist. In flight the main forms of ice are clear ice, also called glaze, rime ice and rain ice. As the scene shows, ice builds first on the leading edges of the wings, tailplane, struts and propeller blades, where the droplets strike. And over many years the airframe also collects scratches, dents, repairs, dirt and grease, a slow form of contamination we will finish with.
Part 1 · Frost
Frost: a thin coat of ice crystals A fairly thin coating of crystalline ice On the ground : when the temperature falls below 0 °C , typically on a clear, calm night In flight : after flying in sub-zero air, the aircraft moves into a warmer, moist layer Thin, but rough : its danger is roughness, not weight Must be removed before take-off
heat radiates away
Parked, clear calm night
skin below 0 °C
vapour deposits as frost
high · well below 0 °C
warmer, moist layer
Cold-soaked, then descends
skin still below 0 °C
in warmer, moister air
Chapter 14 · Airframe Contamination
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Frost is a fairly thin coating of crystalline ice. On the ground it forms when the temperature falls below zero, typically on a clear, calm night when the aircraft skin radiates its heat away to the sky and water vapour turns straight into ice crystals on the cold surfaces. In flight it can form when an aircraft has been flying in air below zero and then moves into a warmer, moist layer, for example during a quick descent. The skin is still well below freezing, so the moisture in the warmer air deposits on it as frost. Frost looks harmless because it is so thin and adds almost no weight. Its danger is roughness. As you will see shortly, a layer as rough as sandpaper can cut the lift substantially, so frost must always be removed before take-off.
Part 1 · Ice
Clear ice, rime ice and rain ice
Rime ice
small droplets freeze at once
white, opaque, rough · no run-back
Clear (glaze) ice
runs back
large drops freeze slowly
smooth, translucent · run-back · horns
Rain ice
runs back
supercooled rain below an inversion
heavy glaze · far run-back · builds fast
The difference is how fast the water freezes : instantly (rime), after some run-back (clear), or after a long run-back from supercooled rain (rain ice).
Chapter 14 · Airframe Contamination
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are three main forms of ice. Rime ice forms when small supercooled droplets strike the leading edge and freeze almost at once, so there is no run-back. Air is trapped between the frozen droplets, which makes rime white, opaque and rough, and it grows forward into the airflow. Clear ice, or glaze, forms from large supercooled drops. They do not freeze immediately, so some of the water flows back along the surface behind the leading edge before it freezes. The result is a smooth, translucent layer, often with horns above and below the stagnation point. Rain ice is the worst. It forms from rain that has become supercooled, and because it does not freeze straight away, it runs far back over the surfaces and builds up very quickly into a thick, heavy glaze. Think of the three as a scale of how quickly the water freezes.
Part 1 · Rain ice
Rain ice: rain falling out of an inversion Rain falls from a warm layer aloft (an inversion) into air below 0 °C It becomes supercooled and freezes when it hits the aircraft Drops are large: considerable run-back before freezing Builds up very quickly : heavy glaze, far back on the surfaces Typical ahead of a warm front ; escape is usually a climb into the warm layer
-10
0
+10
temperature °C
height
warm layer
below 0 °C
warm-sector cloud
freezing level
rain (liquid, above 0 °C)
supercooled rain
ice builds very fast
Chapter 14 · Airframe Contamination
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Rain ice needs a particular temperature structure, shown on the left. Aloft there is a layer of air warmer than zero, often the warm air riding up over a warm front, which forms an inversion. Rain falling from that warm layer is ordinary liquid rain. As it falls into the air below, which is colder than zero, it does not freeze; it becomes supercooled. When those large supercooled drops strike an aircraft flying in the cold layer, they do not freeze immediately. They spread and run a long way back over the wings and tail before freezing, and they arrive in such quantity that the ice builds up very quickly. Rain ice is heavy, it covers areas that ice protection systems do not reach, and it is one of the most dangerous forms of icing. Because the warm layer is above, a climb is often the quickest way out.
Part 2 · Aerodynamic effects
Three ways contamination hurts Profile Ice changes the shape of the leading edge: horns and ridges the wing was never designed for. Large drag rise, big loss of CL max .
Roughness Frost, rime and snow make the surface rough : more skin friction, a tired boundary layer, earlier separation.
Weight Clear and rain ice can be heavy : higher stall speed, more induced drag, less climb, more fuel.
Chapter 14 · Airframe Contamination
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
However many forms contamination takes, it harms the aircraft in only three ways. First, it modifies the profile. Ice on the leading edge creates horns and ridges that the designer never intended, giving a large increase in drag and a substantial loss of C L max. Second, it increases the roughness of the surface. Frost, rime and snow make the skin rough, which raises skin friction and drains energy from the boundary layer so that it separates earlier. Third, it increases the weight. Clear ice and rain ice in particular can add a great deal of weight, which raises the stalling speed and the induced drag, reduces the climb performance and increases fuel burn. When you meet any contamination question, ask yourself which of these three effects is at work.
Part 2 · Roughness
Frost: roughness drains the boundary layer Main effect of frost: surface roughness Roughness increases the energy loss in the boundary layer Skin friction drag increasesThe boundary layer separates earlier : lower CL max and a lower stalling angle Take-off with frost at normal speeds can mean a stall just after lift-off
Smooth wing
separation at 80% chord
Frosted wing
separation at 45% chord
Rough skin: more skin friction, earlier separation, lower C L max
Chapter 14 · Airframe Contamination
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The main effect of frost is to make the surface rough. As the air flows over a rough skin, the boundary layer loses more of its energy to friction, and two things follow. The skin friction drag increases. More importantly, the tired boundary layer cannot push as far against the adverse pressure gradient on the rear of the upper surface, so it separates earlier, at a lower angle of attack. In the scene the frosted section starts to separate well before it would if it were clean. That means a lower C L max and a lower stalling angle. Now imagine taking off with frost on the wings. The pilot rotates at the normal speed and the normal attitude, expecting the usual margin above the stall, but the frosted wing stalls at a lower angle and a higher speed, so the aircraft can stall just after lift-off.
Part 2 · Numbers
Sandpaper on the wing: 30 % less lift, 40 % more drag Frost, ice or snow as rough as medium or coarse sandpaper can cut lift by up to 30 % and raise drag by 40 % VS ∝ 1/√CL max : with 70 % of CL max , VS rises by 1/√0.7 ≈ 1.2 Example: VS 120 → 143 kt A normal lift-off at about 1.1 × clean VS = 132 kt is now below the stall The stall also comes at a lower angle of attack
-4°
0°
4°
8°
12°
16°
20°
0
0.5
1
1.5
angle of attack
C L
clean 1.6
contaminated 1.12 (−30%)
Clean V S
120 kt
Contaminated V S = 120 ÷ √0.7
143 kt
Normal lift-off ≈ 1.1 × clean V S
132 kt
Lift off at the usual speed and the wing is below its new stall speed
Chapter 14 · Airframe Contamination
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
How big is the effect? Tests have shown that frost, ice or snow with the thickness and roughness of medium or coarse sandpaper can reduce lift by as much as thirty per cent and increase drag by forty per cent. Let us turn that into a speed. The stalling speed varies with one over the square root of C L max. If only seventy per cent of C L max remains, the stalling speed goes up by one over the square root of nought point seven, which is about one point two. So a clean stalling speed of one hundred and twenty knots becomes about one hundred and forty three knots. If the crew lift off at their normal speed, around one point one times the clean stalling speed, that is about one hundred and thirty two knots, which is now below the contaminated stalling speed. On the graph you can also see the stall arriving at a lower angle of attack.
Part 2 · Leading edge ice
Ice on the leading edge: a new and worse aerofoil Ice forms on and behind the leading edges of the wings and tailplane It can severely distort the leading edge profile, with horns and ridges Result: a large increase in drag and a substantial decrease in CL max Higher stalling speed and a lower stalling angle The tailplane suffers too: its CL max also falls
separated flow behind the horn
Severe distortion of the profile:
large rise in drag, substantial fall in C L max,
stall at a lower angle and a higher speed.
upper horn
Chapter 14 · Airframe Contamination
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ice normally forms on and just behind the leading edges of the wings and the tailplane, exactly where the shape matters most. Glaze ice in particular can grow horns above and below the stagnation point, so the wing now has a completely different and much worse leading edge. The air cannot follow the sharp horns, it breaks away behind them, and the flow over the upper surface is disturbed from the very front. The result is a large increase in drag and a substantial decrease in C L max. Watch the scene: as the angle of attack is raised, the iced section reaches its stalling angle at only about eight or nine degrees, where a clean wing would still be flying comfortably. So the stalling speed rises and the stalling angle falls. Remember that the tailplane is an aerofoil too, and its C L max falls in exactly the same way.
Part 2 · Weight
The weight of ice: stall speed, drag and climb Clear and rain ice can add considerable weight More weight: higher stalling speed (VS ∝ √W) and more induced drag Plus more parasite drag from the rough, distorted shape The thrust minus drag margin shrinks : poorer climb More power to hold height, so more fuel
140
180
220
260
300
340
0
25
50
75
100
TAS (kt)
Drag and thrust
thrust available
margin 26
margin 13
iced: +40% parasite drag, +5% weight
clean
Less excess thrust: poorer climb.
More power to hold height: more fuel burned.
Chapter 14 · Airframe Contamination
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Clear ice and rain ice can add a lot of weight to the airframe. More weight means a higher stalling speed, because the stalling speed goes with the square root of the weight, and it means more induced drag, because the wing must make more lift. On top of that, the rough, distorted shape adds parasite drag. The graph puts numbers on it. With forty per cent more parasite drag and five per cent more weight, the minimum drag rises from about fifty four to about sixty seven units. With eighty units of thrust available, the margin of thrust over drag, which is what lets you climb, falls from about twenty six to about thirteen: roughly half. So the iced aircraft climbs much less well, and in level flight it needs more power to hold height, which means more fuel burned, at exactly the moment you may need the performance to climb out of the icing.
Part 3 · Tailplane stall
The iced tailplane and flap selection The tailplane normally works at a negative angle , giving a download Its thin leading edge collects ice well, so its CL max falls Lowering flap increases the downwash : the tail angle becomes more negative At low speed it can stall , losing its download: the nose pitches down Result: loss of longitudinal control , often close to the ground
more downwash
with flap
iced tail stalls on its
lower surface
ice on tail
Download lost → the nose pitches down
Loss of longitudinal (pitch) control
Most likely at low speed just after selecting flap
Chapter 14 · Airframe Contamination
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The tailplane is an aerofoil too, and it usually works at a negative angle of attack, producing a downward force that balances the aircraft. Its leading edge is thinner than the wing's, so it collects ice very efficiently, and ice lowers its C L max just as it does for the wing. Now select flap. Lowering the flap increases the downwash behind the wing, so the air reaches the tailplane at a more negative angle. At low speed, with an iced leading edge, that can be enough to stall the tailplane on its lower surface. When it stalls, the download it was providing collapses and the nose pitches down, as in the scene. That is a loss of longitudinal control, and it typically happens on the approach, just after flap selection and close to the ground. It is one of the most dangerous icing events.
Part 3 · Recognition and recovery
Wing stall or tailplane stall? Wing stall (ice) Tailplane stall (ice) Typical trigger High α, low speed, turning Flap selection , often at higher speed; nose-down pitch changesWhat you feel Airframe buffet, wing drop or roll oscillation, high sink rate Elevator buffet, light or changing stick forces , sudden nose-down pitch Stall warning May not sound before the stall Will not sound (the wing is not near the stall) Recovery: flap Keep the flap setting Retract flap to the previous settingRecovery: pitch Reduce α : nose downPull : nose-up elevatorRecovery: power Increase power Reduce power if it is high
The recoveries are opposite in pitch. Getting them mixed up makes either stall worse, so identify which surface has stalled first.
Chapter 14 · Airframe Contamination
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the cures are opposite, you must tell a wing stall from a tailplane stall. An ice-induced wing stall comes at high angle of attack and low speed, often in a turn. You feel airframe buffet, a wing drop or roll oscillation, and a high rate of descent, and the stall warning may not sound at all. The recovery is the familiar one: reduce the angle of attack, keep the flap where it is and add power. A tailplane stall is typically triggered by selecting flap. Clues are buffet felt through the elevator, light or changing stick forces and a sudden pitch down, and the stall warning will not sound because the wing is nowhere near its stall. The recovery is to retract the flap to the previous setting, pull back to raise the nose, and reduce power if it is high. If an exam question describes pitch control trouble after flap selection with suspected tail ice, the answer is to reduce the flap setting.
Part 3 · Wing stall
Ice-induced wing stall: trust the right cues The stall warning is calibrated for a clean wing ; ice makes the wing stall at a lower α So the warning may come late or not at all Reliable cues: airframe buffet , a roll problem (wing drop, roll oscillation), a high rate of descent A nose-down pitch is not guaranteed Loss of elevator effectiveness points to a tailplane stall
Icing-induced wing stall: which cues can you trust?
Airframe buffet
Roll problem: wing drop or roll oscillation
High rate of descent
Stall warning (set for a clean wing)
Nose pitching down
Loss of elevator effectiveness
Reliable: buffet, roll problem, high descent rate
Chapter 14 · Airframe Contamination
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
When ice is on the wing, the stall happens at a lower angle of attack than the clean wing's. Stall warning systems, whether a horn or a stick shaker, are set to trigger at a clean-wing angle of attack, so with ice the wing may stall before the warning activates, or the warning may never come. Which cues can you rely on? Airframe buffet, a roll control problem such as a sudden wing drop or a growing roll oscillation, because the ice is never exactly the same on both wings, and a high rate of descent. In the scene one wing stalls first and the aircraft drops a wing. A pitch-down may or may not happen, so it is not reliable. And a loss of elevator effectiveness is the signature of a tailplane stall, not a wing stall. That gives the exam answer: buffet, roll control problem and high rate of descent.
Part 3 · Seeing the ice
You may not be able to see it In flight, visual evidence of icing may not exist Clear ice is transparent and smooth: it can look like wet metalThe tailplane , which often ices first, cannot be seen from the flight deck At night, only areas lit by the ice inspection lights can be checked Ice detectors sense ice on their own probe , not on every surface
ice light
wing leading edge: partly visible
tailplane: not visible
ice detector probe
Clear ice is transparent: it looks like wet metal
The tail usually collects ice first and is out of view
At night you see only what the ice light shows
A detector senses its own probe, not the whole airframe
Chapter 14 · Airframe Contamination
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
How do you know the airframe is contaminated? The honest answer is that you may not. Visual evidence of icing may simply not exist. Clear ice is transparent and smooth, and on a leading edge it can look like nothing more than wet metal. The tailplane, which often collects ice before the wing because its leading edge is thinner, cannot be seen from the flight deck at all. At night you can only see the parts of the wing lit by the ice inspection lights. And an ice detector only senses ice forming on its own probe; it tells you that you are in icing conditions, not how much ice is on each surface. So the exam answer is that visual evidence of accumulated ice may not exist, and good practice is to treat icing conditions as icing, use the protection systems early, and watch the performance.
Part 3 · Propellers
Ice on the propeller Ice on the blades upsets the propeller's balance Result: severe vibration , especially when ice breaks off one blade Ice also spoils the blade sections: less thrust and efficiency Pieces shed from the propeller can damage the fuselage Hence propeller de-icing, and reinforced panels beside the disc
shed ice
hits fuselage
fuselage
Uneven ice → out of balance → severe vibration
and a loss of propeller efficiency (thrust)
piece lost from this blade
Chapter 14 · Airframe Contamination
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The propeller blades are rotating aerofoils, and they ice up like any other leading edge. Because the propeller spins at high speed, even a small difference in the mass on each blade upsets its balance and causes vibration. The vibration is worst when a piece of ice breaks off one blade but not the others, leaving the propeller badly out of balance, and severe vibration can damage the engine mountings. The ice also spoils the shape of the blade sections, so the propeller makes less thrust for the same power. Finally, the pieces of ice that are shed are thrown outwards at high speed, and they can strike and damage the fuselage beside the propeller disc. That is why many propeller aircraft have propeller de-icing and reinforced panels on the fuselage sides in line with the blades.
Part 3 · Instruments
Iced pitot heads and static vents Ice on pitot heads and static vents causes errors in the pressure instruments Eventually they may fail to show any reading at all Pitot iced: the airspeed indicator is wrong Static iced: altimeter stuck, VSI at zero, ASI wrong when height changes Prevention: pitot heat on; alternate static if needed
pitot tube: ram hole iced over
static vent iced
Pitot blocked
ASI wrong; with the drain also blocked it
reads like an altimeter (over-reads in a climb)
Static blocked
altimeter stuck, VSI at zero; ASI under-reads
in a climb and over-reads in a descent
Both, in time
pressure instruments read nothing useful
use pitot heat and the alternate static
Chapter 14 · Airframe Contamination
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The pressure instruments get their information through small holes: the pitot head facing the airflow and the static vents on the side of the fuselage. Ice forming over those holes first causes errors in the readings and eventually can stop the instruments showing anything useful. If the pitot head ices, the airspeed indicator is wrong; if its drain hole also freezes, the trapped pressure makes the airspeed indicator behave like an altimeter, over-reading as you climb. If the static vent ices, the altimeter freezes at its last reading, the vertical speed indicator shows zero, and the airspeed indicator under-reads in a climb and over-reads in a descent. Unreliable airspeed in icing conditions has caused serious accidents. The defence is to have pitot heat on whenever icing is possible, and to use the alternate static source if the static vents are blocked.
Part 3 · Controls
Ice in the control gaps Ice can form in the gaps around any movable surface Pieces of ice breaking off can lodge in the gaps Controls become difficult to move or immovable Affects ailerons, elevator, rudder, trim tabs and flaps Exercise the controls in prolonged icing, and check full and free movement on the ground
ice bridges the hinge gap
shed ice lodged in the gap
tailplane
elevator
Any movable surface can jam:
ailerons, elevator, rudder, trim tabs, flaps
Controls become stiff, heavy or immovable
Chapter 14 · Airframe Contamination
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every movable surface on the aircraft has a gap between it and the fixed structure, and ice can form in those gaps. Water runs back into them and freezes, or ice builds across the hinge line until it bridges the gap. Pieces of ice breaking off further forward can also be carried back and become jammed in a gap. Either way, the control becomes stiff and heavy, or in the worst case it cannot be moved at all. This applies to the ailerons, elevator and rudder, and also to trim tabs and flaps, which may refuse to move when selected. On the ground, after the aircraft has stood in freezing precipitation, the controls must be checked for full and free movement. In the air, during prolonged icing, some operators recommend moving the controls from time to time to stop ice bridging the gaps.
Part 4 · Prevention
The clean aircraft: take off with nothing on the wing After exposure to severe weather, all snow and ice (and frost) must be removed Do not count on snow blowing off in the take-off run Frost on the upper wing: the stall comes at a lower angle of attack De-ice with heated fluid, then anti-ice with thickened fluidTake off within the holdover time , which falls in heavier precipitation
Clean aircraft: remove ALL frost, ice and snow
1 · De-ice
heated fluid removes
frost, ice, snow
2 · Anti-ice
thickened fluid stops
new build-up
3 · Take off
before the holdover
time expires
Frost on the upper wing: stall at a lower α, higher speed
Loose snow does not "blow off" reliably: remove it
Holdover time shortens in heavier precipitation
Check again just before take-off if in doubt
Chapter 14 · Airframe Contamination
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The rule for take-off is simple: the aircraft must be clean. After it has been exposed to severe weather, all snow, ice and frost must be removed from the wings, tail and control surfaces. Do not leave smooth ice because it looks harmless, and do not count on loose snow blowing off during the take-off run; it may stick and freeze. Remember that frost covering the upper surface of the wing makes the aircraft stall at a lower angle of attack than normal, which is exactly what the earlier slides showed. In practice the aircraft is first de-iced, usually with heated fluid that removes the deposits. Then it may be anti-iced with a thickened fluid that stops new contamination forming for a limited time, called the holdover time. The aircraft must take off before the holdover time runs out, and in heavier precipitation that time is shorter.
Part 4 · Heavy rain
Heavy rain: water on the wing Water drops on the surface trip the boundary layer: transition moves forward Worst on laminar flow sections, which rely on a long laminar run Result: more drag The disturbed boundary layer can separate earlier: a significantly higher stall speed Apply the manufacturer's or operator's speed corrections for take-off and landing in heavy rain
Dry
transition ≈ 42%
Heavy rain
transition ≈ 8%
laminar
turbulent
Wet: more drag, and a significantly higher stall speed
Apply the manufacturer's speed corrections in heavy rain
Chapter 14 · Airframe Contamination
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Even plain water is a contaminant. In heavy rain the wing is covered with drops and rivulets, and they act like roughness. The boundary layer becomes turbulent much further forward than it would on a dry wing. This matters most on laminar flow sections, which are designed to keep a long run of laminar flow; in the drawing transition moves from about forty per cent of the chord to near the leading edge. A turbulent boundary layer has more skin friction, so drag increases. The disturbed boundary layer can also separate earlier at high angles of attack, which can give a significantly higher stalling speed. The impacts of heavy raindrops also cost the aircraft momentum. So when taking off or landing in heavy rain, the crew should apply whatever speed adjustments the aircraft manufacturer or operator recommends.
Part 4 · Airframe ageing
An ageing airframe burns more fuel Over the years: small scratches, minor damage, repairs , dirt and grease Overall effect: more drag , mainly skin friction drag More drag means more fuel , so operating cost rises with age Example: +1.5 % drag on 2500 kg/h ≈ 38 kg/h , about 112 t a year Normal deterioration is allowed for in the performance charts
Worked example: an ageing airframe
Drag increase (skin friction)
+1.5 %
Cruise fuel flow, new
2500 kg/h
Fuel flow, aged (fuel ∝ drag)
2537 kg/h
Extra fuel per hour
≈ 38 kg
Extra fuel per year (3000 h)
≈ 112 t
Causes: small scratches, dents, repairs, dirt, grease
Effect: mostly skin friction drag → fuel → cost
Normal deterioration is allowed for in the performance charts
Chapter 14 · Airframe Contamination
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The last kind of contamination is slow and never dramatic: age. Over a period of years the airframe collects small scratches, minor damage and dents, repair patches, and a general build-up of dirt and grease. None of these changes the wing's shape enough to affect handling, but together they make the surface rougher, and that increases the drag, mainly the skin friction drag. In the cruise the thrust, and so roughly the fuel flow, matches the drag. So in the worked example a one and a half per cent increase in drag on a jet burning two thousand five hundred kilograms an hour costs about thirty eight kilograms an hour, which over three thousand flight hours a year is about one hundred and twelve tonnes of fuel. That is why operating costs rise with the age of the airframe. The normal deterioration is already allowed for in the aeroplane's performance charts.
Summary
Airframe contamination: what to take into the exam Forms Frost (thin, crystalline), rime (no run-back), clear (run-back), rain ice (fast, heavy). Needs high RH and low temperature.
Three effects Profile, roughness, weight. CL max down, drag up, stall speed up, stalling angle down.
Numbers Sandpaper roughness: lift −30 %, drag +40 %. VS × 1/√0.7 ≈ +20 %.
Wing stall Warning unreliable. Trust buffet, roll problem (wing drop) and high sink rate.
Tail stall After flap selection: nose drops. Retract flap to previous setting, pull, reduce power.
Systems Prop: imbalance, vibration, shed ice. Pitot/static: errors then no reading. Controls jam.
Ground Remove ALL snow, ice and frost. De-ice, anti-ice, take off within holdover time.
Rain and age Rain: transition forward, drag and stall speed up. Age: skin friction, fuel, cost.
Chapter 14 · Airframe Contamination
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us sum up. Frost is a thin crystalline coat; rime forms with no run-back; clear ice forms with some run-back; rain ice runs far back and builds very fast. Icing needs moisture and low temperature. Every contaminant works through the profile, the roughness and the weight, lowering C L max and the stalling angle, raising drag and the stalling speed. Sandpaper roughness can cost thirty per cent of the lift and add forty per cent to the drag, raising the stalling speed by about twenty per cent. With ice on the wing, do not trust the stall warning; trust buffet, a roll problem and a high sink rate. A nose drop after flap selection suggests a tailplane stall: retract the flap, pull and reduce power. Ice unbalances propellers, blocks pitot and static vents and jams controls. Take off clean, within the holdover time. Heavy rain and age both add drag.