Principles of Flight · Chapter 18
Dynamic Stability What happens after the first tendency: damping, the phugoid and short-period modes, PIO, Dutch roll, spiral stability and yaw dampers.
Dutch roll: yaw and roll out of phase
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Lesson eighteen asks what happens after the first moment. Static stability tells us which way an aeroplane starts to move when it is disturbed; dynamic stability tells us what the motion does over the following seconds and minutes. We will meet damping, the slow phugoid and the quick short-period pitching mode, and the dangerous pilot-induced oscillation. Then we move to yaw and roll, where the balance between directional stability and dihedral effect decides between a slow spiral and the oscillating Dutch roll, and we see how the yaw damper helps.
Lesson map
From the first tendency to the whole motion Static or dynamic? Static = the first tendency. Dynamic = the motion over time. Six basic time histories.
Damping Aerodynamic damping resists rotation; time to half amplitude; less damping at altitude.
Pitch modes The slow phugoid and the quick short-period oscillation; which one matters.
PIO Pilot-induced oscillation: lag turns corrections into excitation. Release the controls.
Spiral and Dutch roll The balance of directional stability and dihedral effect decides the lateral motion.
Yaw damper Artificial damping of Dutch roll; ailerons, not rudder, if it fails.
Chapter 18 · Dynamic Stability
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson is about what happens after the first moment. We start by separating static from dynamic stability and looking at the six basic ways a disturbed aeroplane can behave over time. Then we look at damping, the thing that makes motion die away, how designers specify it, and why it weakens at high altitude. Next come the two pitching modes: the slow phugoid and the quick short-period oscillation, and why only one of them is really important. That leads to pilot-induced oscillation, where the pilot unknowingly drives the motion. In the second half we look at roll and yaw together: spiral divergence and Dutch roll, and why most aeroplanes are designed with a mild spiral tendency. Finally, the yaw damper, and what to do if it fails.
Part 1 · The idea
Static stability starts it; dynamic stability finishes it Static stability : the initial tendency after a disturbance: back toward equilibrium, away from it, or neitherDynamic stability : the resulting motion with time Positive dynamic stability: the amplitude decreases with timeReturning, the aeroplane usually overshoots because of its momentum, giving oscillations Damping, the dissipation of energy , is what makes those oscillations die away STATIC: the first tendency equilibrium restoring force appears at once DYNAMIC: what happens over time overshoots… …and settles: dynamically stable time →
Chapter 18 · Dynamic Stability
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Static and dynamic stability answer two different questions. Static stability is about the first tendency. Push a ball in a bowl to one side and let go: a restoring force appears straight away, pushing it back toward the bottom. That initial tendency is static stability. Dynamic stability is about what happens next, over time. The ball rolls back, but its momentum carries it past the bottom, up the other side, and back again. If friction slowly takes the energy away, each swing is smaller and it settles: that is positive dynamic stability, because the amplitude of the motion decreases with time. An aeroplane is just the same. Disturbed in pitch, its static stability starts it back toward its trimmed attitude, it usually overshoots, and what happens to those oscillations depends on damping, the dissipation of energy.
Time histories 1
Without oscillation: subsidence, divergence, neutral A Subsidence (dead beat) time → + static + dynamic B Divergence time → − static − dynamic C Neutral time → neutral static neutral dynamic A dead-beat return is both statically and dynamically stable. A steady divergence is both statically and dynamically unstable.
Chapter 18 · Dynamic Stability
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are six basic ways the motion can develop, three without oscillation and three with it. Here are the three without. In A, called subsidence or a dead-beat return, the displacement simply dies away without overshooting. The aeroplane starts back toward equilibrium, so it is statically stable, and the amplitude falls with time, so it is dynamically stable too. In B, divergence, the displacement grows steadily. The initial tendency is to carry on in the direction of the disturbance, which is static instability, and the growing amplitude is dynamic instability. In C, the disturbance leaves the aeroplane in a new position and it simply stays there. There is no tendency either way and the amplitude is constant, so this is neutral static and neutral dynamic stability.
Time histories 2
With oscillation: damped, undamped, divergent D Damped oscillation time → + static + dynamic E Undamped oscillation time → + static neutral dynamic F Divergent oscillation time → + static − dynamic All three are statically stable : each starts back toward equilibrium. Only damping separates them.
Chapter 18 · Dynamic Stability
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the three oscillating cases. In every one of them the aeroplane starts back toward equilibrium, so all three are statically stable. What differs is the dynamic behaviour. In D, a damped oscillation, each swing is smaller than the last, because energy is being dissipated. That is positive dynamic stability, and it is what we want. In E, an undamped oscillation, the swings neither grow nor shrink. This is neutral dynamic stability, like a car with worn-out shock absorbers that keeps bouncing down the road: unpleasant and potentially dangerous. In F, a divergent oscillation, each return to equilibrium is faster than the last, so the swings grow. Energy is being added rather than taken away, and this is dynamic instability. One example is a pilot making control inputs near the aeroplane’s natural frequency, which we will meet as pilot-induced oscillation.
The rule
Dynamic stability needs static stability Static stability does not guarantee dynamic stability , but dynamic stability needs static stability: a statically unstable aeroplane cannot be dynamically stable .
Mode Static Dynamic Example A Subsidence Positive Positive Dead-beat return to trim B Divergence Negative Negative CG aft of the neutral point C Neutral Neutral Neutral CG on the neutral point D Damped oscillation Positive Positive Normal short-period mode E Undamped oscillation Positive Neutral Worn shock absorbers F Divergent oscillation Positive Negative Pilot-induced oscillation
Where natural aerodynamic damping is not enough, artificial damping (pitch or yaw dampers) must supply positive dynamic stability.
Chapter 18 · Dynamic Stability
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table gathers the six cases and gives the rule you must remember. Look at the static column: for an aeroplane to be dynamically stable, it must first be statically stable. If it starts off away from equilibrium, the motion can only grow, so a statically unstable aeroplane cannot be dynamically stable. But the reverse is not true. Static stability does not guarantee dynamic stability: in E and F the aeroplane is statically stable, yet the oscillation does not die away, or even grows. Every aeroplane must show the required static and dynamic stability; a rapidly diverging static instability would make it very hard or impossible to fly, and continued oscillations are unacceptable in many areas. When the natural aerodynamic damping is not enough, designers add artificial damping, such as the pitch dampers and yaw dampers of large jets.
Damping
Aerodynamic damping resists rotation Aerodynamic damping : a moment that opposes a rotation, but only while the rotation is happening Pitching nose up, the tail moves down: extra upflow raises tail α, and tail lift opposes the pitch Same idea in roll (down-going wing gains α) and yaw (the fin) For a given rotation rate, higher TAS means a smaller α change : less damping So damping falls with altitude: ∝ √σ , about half at 40 000 ft (more in lesson 16) nose pitching up tail moves down TAS upflow from pitching airflow at tail: Δα extra tail lift opposes the pitch Worked example: pitch rate 3 °/s, tail arm 15 m Tail vertical speed 3° in rad × 15 m 0.79 m/s Δα at TAS 100 m/s 0.45° Δα at TAS 200 m/s 0.22° Double the TAS, half the damping moment for the same rate
Chapter 18 · Dynamic Stability
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Where does damping come from? Picture the aeroplane pitching nose up. The tailplane, a long way behind the centre of gravity, is moving downward as it swings. Relative to the tail, that downward motion feels like an extra upward airflow. Added to the true airspeed, it increases the tail’s angle of attack, so the tail makes more lift, which pushes the tail up and the nose down, opposing the pitching motion. The key point is that this moment exists only while the aeroplane is rotating: stop the rotation and it disappears. That is the exam definition of aerodynamic damping, a resistance to the rate of displacement. Look at the numbers: three degrees per second with a fifteen metre tail arm gives nought point four five of a degree at one hundred metres per second, but only half that at two hundred. Higher true airspeed means less damping, which is why damping falls with altitude: at forty thousand feet it is only about half its sea-level value.
Specifying damping
Time to damp to half amplitude The required damping is set as the time to damp to half amplitude , T½ After one T½ the swing is half ; after two, a quarter A free aeroplane has six degrees of freedom : three rotations and three translations Longitudinal motion uses three: pitch , plus vertical and horizontal movement Its variables: pitch attitude , angle of attack and TAS ; two modes: phugoid and short period A A/2 A/4 T½ T½ time → Damping is specified by the time to damp to half amplitude: shorter T½ = better damped displacement
Chapter 18 · Dynamic Stability
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
How do designers say how much damping is enough? They use the time to damp to half amplitude. Whatever the first swing is, after one of these intervals the swing is half as big, after two it is a quarter, after three an eighth, and so on. A shorter time means stronger damping. For example, if a pitch oscillation starts at six degrees and the time to half amplitude is half a second, it is down to three degrees after half a second and one and a half degrees after one second. Now some background for pitch. An aeroplane in free flight has six degrees of freedom: rotation in roll, pitch and yaw, and movement forward, sideways and up or down. Because the aeroplane is symmetrical, longitudinal motion needs only three: pitch, plus vertical and horizontal movement, described by pitch attitude, angle of attack and true airspeed. It shows two distinct modes.
Part 2 · Longitudinal modes
The phugoid: a long, slow switchback Also called the long period oscillation ; period about 1 to 2 minutes Large changes in pitch attitude , height and airspeed Angle of attack nearly constant , so little change in load factorAn exchange of potential and kinetic energy about the trimmed speed and height Weakly damped , but so slow that it is easily controlled by the pilot; no special design provision neededhigh · slow low · fast high · slow Pitch attitude, height and speed all vary Angle of attack ≈ constant (little change in g) Period 1–2 minutes · weakly damped Easily controlled by the pilot
Chapter 18 · Dynamic Stability
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The first longitudinal mode is the phugoid, also called the long period oscillation, and it is a gentle switchback. Picture the aeroplane nose up a little above its trimmed path. It climbs, and as it climbs it slows down, trading speed for height. At the top it is high and slow, the nose drops, and it descends, picking up speed as it goes. At the bottom it is low and fast, so it climbs again. Pitch attitude, height and airspeed all change a lot, but the nose follows the flight path, so the angle of attack stays almost constant and the load factor hardly changes. One cycle takes between one and two minutes. Because the pitch rate is so low, damping is weak, but that hardly matters: the motion is so slow that the pilot can easily correct it, and no special design feature is needed.
Worked example
The phugoid trades speed for height 230 kt · high 250 kt · low 230 kt · high 250 kt · low height → speed speed → height Total energy nearly constant: KE and PE swap back and forth Worked example Speed in the trough 250 kt = 128.6 m/s Speed at the crest 230 kt = 118.3 m/s Δh = (V₁² − V₂²) ÷ 2g = (16541 − 14000) ÷ 19.6 Height swing ≈ 130 m ≈ 425 ft A pilot sees the nose rise and speed fall over half a minute or more: plenty of time to correct it Total energy stays almost constant; the phugoid simply moves it between speed and height .
Chapter 18 · Dynamic Stability
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The phugoid is an exchange of energy. Kinetic energy, from speed, turns into potential energy, from height, and back again, while their total stays almost constant. We can put numbers on it. Suppose the speed swings between two hundred and fifty knots in the troughs and two hundred and thirty knots at the crests. Two hundred and fifty knots is about one hundred and twenty-eight point six metres per second, and two hundred and thirty knots is about one hundred and eighteen point three. The height change equals the difference of the squares of the speeds, divided by twice the acceleration due to gravity. That works out at about one hundred and thirty metres, or about four hundred and twenty-five feet. So a twenty knot swing in speed goes with a height swing of over four hundred feet, spread over a minute or more: easy for the pilot to see and to stop.
Longitudinal modes
The short-period oscillation: quick and important Rapid pitch oscillation with a period of about 1 to 2 seconds or less Large changes in angle of attack and so in load factor Speed, height and pitch attitude stay about constantRestored by static stability , reduced by pitch damping At high dynamic pressure it can give severe g loads ; the most important of the two modes Angle of attack (and g) 0 s 1 s 2 s 3 s 4 s Airspeed and height almost unchanged Period about 1–2 s or less: close to pilot reaction time Restored by static stability, damped by pitch damping
Chapter 18 · Dynamic Stability
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The second longitudinal mode is the short-period oscillation, and it is completely different. It is a rapid pitching oscillation, with a period of one or two seconds or even less. The angle of attack changes a lot, and with it the load factor, but because it is over so quickly, the speed, the height and even the flight path hardly change. The aeroplane is pushed back toward equilibrium by its static stability, and each swing is reduced by pitch damping. In a well designed aeroplane it dies away within a cycle or two. But at high dynamic pressure, large rapid changes of angle of attack can produce severe g loads, enough to damage the structure. That, and its speed, make the short-period oscillation the more important of the two longitudinal modes.
Side by side
Phugoid against short period Phugoid (long period) Short period Period 1–2 minutes 1–2 seconds or lessWhat changes Pitch attitude, height , airspeed Angle of attack , load factor (g)Nearly constant Angle of attack Speed and heightDamping Weak Normally strong (pitch damping) Pilot control Easy : plenty of timeNot easy : close to reaction time; risk of PIODanger Little Severe g loads at high dynamic pressureRemedy Normal pilot correction Release the controls ; pitch dampers on jets
Chapter 18 · Dynamic Stability
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the two longitudinal modes side by side, because the exam loves to swap their features. The phugoid takes one to two minutes per cycle; the short period takes one or two seconds or less. In the phugoid, pitch attitude, height and airspeed change while the angle of attack stays nearly constant. In the short period, the angle of attack and load factor change while speed and height stay nearly constant. The phugoid is weakly damped but easy to control because it is so slow. The short period is normally well damped, but it is not easily controlled by the pilot, because its period is close to human reaction time, and trying can make it worse. The phugoid is of little danger; the short period can produce severe g loads. For the phugoid, just fly the aeroplane; for the short period, release the controls, and large jets carry pitch dampers.
Pilot-induced oscillation
PIO: when the pilot drives the motion PIO : pilot response lag plus control-system lag turn corrections into excitation Inputs arrive in phase with the motion: negative damping , the oscillation grows Possible about any axis; most important with the short-period pitch mode It can reach dangerous amplitude and failing loads in a very short time Cure: release the controls immediately ; the aeroplane’s own damping recovers it Prompt input: opposes the motion solid: pitch · dashed: pilot input Input ½ cycle late: reinforces it solid: pitch · dashed: pilot input
Chapter 18 · Dynamic Stability
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
A pilot-induced oscillation happens when the pilot, trying to help, actually drives the motion. In the top picture the pilot’s input is prompt, so it opposes the pitching motion and the oscillation dies away. Now add the normal human reaction lag and the lag in the control system. If together they come to about half a cycle, the pilot’s push arrives just as the nose is already going down, and the pull just as it is going up. The inputs are now in phase with the motion, adding energy: that is negative damping, and the oscillation grows, as in the bottom picture. It can happen about any axis, but it matters most in the short-period pitch mode, where the cycle is about as long as the reaction time and the amplitude can become dangerous in seconds. Even trying to hold the stick still can feed it. The cure is to release the controls.
Part 3 · Lateral and directional
Sideslip couples roll and yaw In a sideslip the lateral and directional responses are coupled One sideslip makes a rolling moment and a yawing moment together Two principal effects: dihedral effect (roll due to sideslip) and directional stability (yaw due to sideslip) Their ratio , not either one alone, decides the lateral dynamic behaviour Too much directional: spiral . Too much dihedral effect: Dutch roll SIDESLIP β Rolling moment dihedral effect (lateral stability) Yawing moment directional stability (fin) Directional ≫ dihedral effect → spiral divergence Dihedral effect ≫ directional → Dutch roll The two always act together: coupled motion
Chapter 18 · Dynamic Stability
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Last lesson we studied roll and yaw separately. In real flight they are coupled, because a sideslip produces both at the same time. With the relative airflow coming from one side, the dihedral effect creates a rolling moment that tends to raise the into-wind wing, and the directional stability creates a yawing moment that turns the nose into the airflow. These are the two principal effects behind all lateral dynamic behaviour: rolling moment due to sideslip, and yawing moment due to sideslip. What matters is their ratio. If directional stability is very strong compared with the dihedral effect, the aeroplane tends toward spiral divergence. If the dihedral effect is strong compared with directional stability, it tends toward Dutch roll. The designer cannot remove one without making the other more likely, so the art is in the balance.
Spiral stability
Spiral divergence: strong fin, weak dihedral effect Occurs when directional stability is very large compared with the dihedral effect After a small sideslip the fin yaws the nose into wind toward the low wing , while the weak dihedral effect lags A slow spiral starts and gradually tightens into a spiral dive The motion is not violent ; the divergence is so gradual that the pilot can easily control it A mild spiral tendency is acceptable and is what most aeroplanes have 10° 25° 45° Bank grows slowly at each turn Strong directional stability, weak dihedral effect Slow, not violent: easily held by the pilot Left alone it becomes a steep spiral dive
Chapter 18 · Dynamic Stability
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Spiral divergence occurs when directional stability is very large compared with the dihedral effect. Picture a small disturbance that drops a wing. The aeroplane slips toward the low wing. The big, effective fin swings the nose quickly into the relative airflow, which means toward the low wing, so the aeroplane starts to turn. Meanwhile the weak dihedral effect is slow to raise the wing. In the turn, the outer wing is moving faster and making more lift, so the bank slowly increases, the nose drops, and the aeroplane enters a gently tightening spiral that becomes a spiral dive if nobody does anything. But notice the character of it: it is not violent. The divergence is usually so gradual that the pilot can control it without difficulty. That is why a mild spiral tendency is accepted on most aeroplanes, especially in cloud where the pilot must watch the attitude indicator.
Step by step
How a spiral dive develops 1 Wing drops slip toward the low wing sideslip 2 Fin yaws the nose toward the low wing: a turn starts nose yaws right 3 Outer wing faster more lift: bank increases outer wing bank ↑ 4 Nose drops less vertical lift: spiral dive descent steepens Each step is slow. The pilot simply levels the wings, but left alone the spiral steepens and speed builds.
Chapter 18 · Dynamic Stability
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow the spiral one step at a time. One: a gust drops the right wing, and the aeroplane begins to slip to the right, toward the low wing. Two: the strong fin weathercocks the nose into the relative airflow, which yaws the nose to the right, toward the low wing, and the aeroplane begins to turn. Three: in the turn, the outer, left wing travels faster than the inner wing, so it makes more lift and the bank increases. The weak dihedral effect cannot stop it. Four: with more bank, the vertical component of lift is reduced, so the nose drops and the aeroplane starts to descend in a spiral that steepens, with speed building up. At any point a pilot can simply roll the wings level, because each step is slow. The danger comes only when no one is watching, for example in cloud without a good attitude reference.
Dutch roll
Dutch roll: strong dihedral effect, weaker fin Occurs when the dihedral effect is large compared with directional stability A coupled oscillation in yaw and roll , the two out of phase Yaw: the advancing wing gains lift, so the aeroplane rolls ; the rising wing’s induced drag yaws it back The wingtips trace loops ; the motion repeats in the other direction Objectionable because it is oscillatory; worse with high altitude and high CLnose swings left ↔ right Right wingtip seen from the side high aft low fwd Yaw and roll oscillate together, roll lagging yaw by about a quarter cycle Dihedral effect strong compared with directional stability
Chapter 18 · Dynamic Stability
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Dutch roll occurs when the dihedral effect is large compared with directional stability, and it is an oscillation in yaw and roll together. Suppose the nose yaws to the right. The left wing swings forward, moves faster, and, with the strong dihedral effect, gains lift, so the aeroplane rolls to the right. Now the left wing is rising, and a wing with more lift has more induced drag, so that drag pulls the left wing back and yaws the nose to the left. The whole process now repeats the other way. The roll follows the yaw about a quarter of a cycle later, so the wingtips trace loops, as the green and red trails show. Dutch roll is objectionable because it is an oscillation, uncomfortable for passengers and hard for the pilot to stop, especially at high altitude where damping is weak.
Inside the motion
Yaw leads, roll follows a quarter cycle later yaw right roll right ¼ cycle solid: yaw ψ · dashed: roll φ time → One cycle, step by step 1 Nose yaws right (gust or rudder) 2 Left wing advances: faster, more lift 3 Strong dihedral effect: rolls right 4 Rising left wing: more induced drag 5 Drag yaws the nose back to the left 6 …and the whole cycle reverses Yaw and roll have the same period but are out of phase , which is why the wingtips draw loops rather than lines.
Chapter 18 · Dynamic Stability
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph shows a lightly damped Dutch roll as two traces. The solid line is the yaw angle and the dashed line is the roll angle. Both have the same period, but the roll peak comes about a quarter of a cycle after the yaw peak. Follow the steps on the right. The nose yaws right, perhaps from a gust or a careless rudder input. The left wing advances, moving faster and making more lift. With a strong dihedral effect the aeroplane rolls right. The rising left wing now has more induced drag, which yaws the nose back to the left. Then everything reverses. Because the roll lags the yaw, each wingtip moves forward and back while it moves up and down, and traces an elliptical loop. If you ever see the horizon describing slow loops through the windscreen, think Dutch roll.
Yaw damper
The yaw damper: artificial damping Aeroplanes prone to Dutch roll carry a yaw damper It moves the rudder automatically, in proportion to the rate of yaw It augments stability by adding damping; it does not change the static stability If it fails: damp Dutch roll with the ailerons (roll inputs) Using rudder : response lag gives PIO ; the Dutch roll can quickly become divergent Yaw-rate sensor (gyro) Yaw damper computer Rudder actuator Aeroplane yaws less rate of yaw rudder ∝ yaw rate If the yaw damper fails • Damp the Dutch roll with the AILERONS (roll inputs) • Do NOT chase it with rudder: response lag gives PIO and the oscillation may become divergent, with loss of control The damper augments stability (artificial damping)
Chapter 18 · Dynamic Stability
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aeroplanes with a tendency to Dutch roll, which includes most swept-wing jets, are fitted with a yaw damper. A sensor measures the rate of yaw, and the yaw damper moves the rudder automatically, in proportion to that rate, to oppose the yawing motion. In other words, it adds damping, artificially. It does not change the static stability; it augments the dynamic stability, which is the answer the exam wants. Now the important part: what if it fails in flight? The recommended technique is to damp the Dutch roll with the ailerons, using roll inputs. Do not try to stop it with the rudder. Because of the pilot’s response lag, rudder inputs tend to arrive at the wrong moment, causing a pilot-induced oscillation, and the Dutch roll can very quickly become divergent, leading to loss of control.
Swept wings
Sweepback shifts the balance with speed Sweepback’s dihedral effect is proportional to CL , so it changes across the speed range Low CL (high speed): dihedral effect small: spiral tendency may appearHigh CL (low speed): dihedral effect large: Dutch roll tendency increasesHigh altitude cuts damping further, so swept-wing jets need yaw dampers Anhedral on high swept wings keeps the dihedral effect in check dihedral effect directional stability SPIRAL tendency DUTCH ROLL tendency lift coefficient CL → high speed low speed Swept wing: the balance shifts with speed Dutch roll is worst slow, at high CL
Chapter 18 · Dynamic Stability
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Sweepback makes the picture change with speed. Remember that the dihedral effect of a swept wing is proportional to the lift coefficient. At high speed, at a low lift coefficient, the dihedral effect is small, directional stability dominates, and the spiral tendency may show. At low speed, at a high lift coefficient, the dihedral effect is large, and it may outweigh directional stability, so the Dutch roll tendency increases. Directional stability itself falls a little at high angles of attack, which makes the low-speed case worse. Add the reduced damping at high altitude, and you can see why swept-wing jet transports have yaw dampers, and why high-mounted swept wings are given anhedral to keep the dihedral effect from becoming excessive. For the exam: swept wing, low speed, high lift coefficient, more Dutch roll; high speed, low lift coefficient, more spiral tendency.
Design balance
Why most aeroplanes are mildly spirally unstable dihedral effect (roll due to sideslip) → directional stability → SPIRAL DIVERGENCE slow, tolerable if gradual DUTCH ROLL oscillatory, objectionable too little directional stability: directional divergence most aeroplanes mild spiral side The design choice High directional stability enough to stop Dutch roll also prevents directional divergence Minimum necessary dihedral effect no more than satisfactory lateral stability needs Result: a mild spiral tendency, much preferred to Dutch roll Dutch roll is objectionable ; a slow spiral is tolerable . So: high directional stability, minimum necessary dihedral effect.
Chapter 18 · Dynamic Stability
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
This map puts the whole story together. Across the bottom is the dihedral effect, and up the side is directional stability. Up in the top left, where directional stability is strong and the dihedral effect weak, lies spiral divergence. Down in the bottom right, where the dihedral effect is strong and directional stability weak, lies Dutch roll. Along the very bottom, with too little directional stability, the aeroplane would diverge in yaw. Which side should a designer choose? Dutch roll is objectionable because it oscillates, while a slow spiral is tolerable if the rate is low. And directional stability high enough to prevent objectionable Dutch roll is automatically enough to prevent directional divergence. So designers give high directional stability and only the minimum dihedral effect needed for satisfactory lateral stability. The result is that most aeroplanes show a mild spiral tendency, which is much preferred to Dutch roll.
Summary
What to take into the exam Static vs dynamic Static = initial tendency ; dynamic = motion with time . Statically unstable can’t be dynamically stable.
Damping Opposes rotation only while it happens . Specified by time to half amplitude . ∝ √σ: half at 40 000 ft.
Phugoid 1–2 min; pitch, height, speed vary; α constant ; weakly damped; easy to control.
Short period 1–2 s; α and g vary; speed constant; most important; release controls .
PIO Lagged inputs give negative damping ; most serious in the short-period mode.
Spiral Strong directional, weak dihedral . Slow, not violent, easily controlled.
Dutch roll Strong dihedral, weak directional . Yaw and roll out of phase. Reduce with anhedral or a bigger fin.
Yaw damper Rudder ∝ yaw rate ; augments stability. If failed: ailerons , never rudder.
Chapter 18 · Dynamic Stability
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Static stability is the initial tendency, dynamic stability is the motion with time, and a statically unstable aeroplane can never be dynamically stable. Aerodynamic damping opposes a rotation only while it happens; it is specified by the time to half amplitude, and it is proportional to the square root of relative density, so it halves by forty thousand feet. The phugoid takes one to two minutes, with constant angle of attack, and is easy to control. The short period takes a second or two, changes angle of attack and g, and is the important one: release the controls. Pilot-induced oscillation is negative damping from lagged inputs. Spiral divergence comes from strong directional stability and weak dihedral effect, and is slow. Dutch roll comes from strong dihedral effect and weaker directional stability; anhedral or a bigger fin reduces it, and the yaw damper damps it. If the damper fails, use the ailerons.