Principles of Flight · Chapter 13
High Lift Devices Flaps, slats, slots and Krueger flaps: how a wing built for cruise is reshaped for slow, safe take-offs and landings.
slat
Fowler flap
more camber · more area · energised boundary layer
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to high lift devices. An airliner wing is designed to cruise efficiently at high speed, yet the same wing has to lift the aeroplane off the runway and land it again at a speed slow enough to stop safely. The answer is to change its shape. In this lesson you will watch slats move forward and flaps slide out, and you will learn exactly what each device does to C L max, the stalling angle, drag, the lift to drag ratio and the pitching moment, and how crews manage them on every flight.
Roadmap
Reshaping the wing for low speed 1 · Why Stall speed, C L max and runway distances. The cruise wing versus the landing wing.
2 · Trailing edge flaps Plain, split, slotted and Fowler. Lift, drag, stalling angle, L/D and pitch.
3 · Leading edge devices Krueger and droop flaps, slats and slots, automatic slats.
4 · Operating them Sequence, asymmetry, load relief, flap settings, retraction and extension.
Chapter 13 · High Lift Devices
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. First, why we need high lift devices at all: the link between C L max, the stalling speed and the length of runway an aeroplane needs. Second, the trailing edge flaps, plain, split, slotted and Fowler, and exactly how each one changes the lift curve, the drag, the stalling angle, the lift to drag ratio and the pitching moment. Third, the leading edge devices: Krueger flaps, drooping or variable camber flaps, slats and slots, including slats that open on their own. Finally, how crews operate all of this, including the correct order of operation, what happens with asymmetric flaps, flap load relief, the choice of flap setting, and how to fly the lift curve when you retract or extend the flaps. Keep the lift curve in your mind throughout; almost every exam question here comes back to it.
Part 1 · Why
Lower stall speed, shorter runways High lift devices reduce take-off and landing distances , so heavier weights and payloads can use a given runway Regulations set speeds as a margin over the stall: about 1.2 VS1 for take-off, 1.3 VS0 for landing VS = √(2W ÷ ρSCL max ): raise CL max and every speed falls Distances go with speed squared , so a small speed cut saves a lot of runway Example: CL max 1.5 → 2.7 cuts VS from 140 to 104 kt and the ground run to about 56 %
VS = √( 2W ÷ ρ S CL max )
same weight, same air density, same wing
C L max
clean
1.5
flaps + slats
2.7
Stall speed V S (kt)
clean
140
flaps + slats
104
Landing speed 1.3 V S (kt)
clean
182
flaps + slats
136
Ground run ∝ V² (%)
clean
100
flaps + slats
56
Distances fall with the square of the speed
Chapter 13 · High Lift Devices
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
High lift devices exist to shorten the take-off and landing distances. Those distances depend on the speeds at the screen, and the regulations set them as a margin above the stall: roughly one point two times V S one for take-off and one point three times V S nought for landing. The stalling speed depends on C L max, so if we raise C L max, every one of those speeds falls. Look at the worked example. A wing with a C L max of one point five stalls at one hundred and forty knots. Deploy flaps and slats to reach two point seven, and at the same weight the stall falls to about one hundred and four knots, because speed goes with one over the square root of C L max. The landing speed falls from one hundred and eighty two to about one hundred and thirty six knots. Distance goes with speed squared, so the ground run is only about fifty six per cent of the clean figure.
Part 1 · Why
A cruise wing cannot also be a landing wing Camber is the big lever on CL max : more camber, more CL at any angle and a higher peakBut a highly cambered wing has high drag at cruise and needs a very nose-down attitude So designers choose a thin, lightly cambered section for cruise A flap is a hinged part of the trailing or leading edge that adds camber when lowered Low-speed aircraft: trailing edge flaps only; jets with symmetrical or negatively cambered noses also need leading edge devices
Cruise: thin, little camber
low drag at high speed · sensible attitude
Take-off and landing: flap down
hinge
more camber → more C L at every angle and a higher C L max
mean camber line
Chapter 13 · High Lift Devices
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
A wing designed for cruise cannot also be the ideal landing wing. Camber is one of the main things that sets C L max: the more camber, the more lift coefficient you get at any angle of attack, and the higher the peak. So for take-off and landing a strongly cambered section would be lovely. In the cruise, though, that same section would give high drag and would have to fly in a very nose-down attitude to keep the lift equal to the weight. Designers therefore choose a thin, lightly cambered section that is efficient at cruise, and then change its shape for low speed. Watch the scene: the rear of the section is hinged, and as it is lowered the camber line curves more and the flow over the top speeds up, all at the same angle of attack. On slow aircraft the flaps are on the trailing edge only; high speed sections, whose noses may be symmetrical or even negatively cambered, need leading edge devices too.
Part 2 · Trailing edge flaps
The trailing edge flap family
Plain flap
rear of section hinges down
simple
good C L max gain
fairly high drag
Split flap
lower-surface plate hinges down
upper surface unchanged
highest drag
Slotted flap
a gap opens ahead of the flap
energised boundary layer
more C L max, less drag
Fowler flap
slides aft, then down
more area + camber
biggest C L max gain
Dashed: retracted. Orange: the moving part. Gain in CL max , complexity and weight all rise from left to right. Inboard flaps also strengthen the spanwise flow towards the root on the upper surface.
Chapter 13 · High Lift Devices
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the trailing edge flap family, each one drawn on the same section with the retracted shape dashed. The plain flap is simply the rear of the section hinged downwards: simple, a good increase in C L max, but fairly high drag. The split flap lowers only a plate from the lower surface; similar lift, even more drag. The slotted flap opens a gap between the wing and the flap so that air from below can flow over the flap; that gives more C L max and much less drag. The Fowler flap first runs aft on tracks, increasing the wing area, and then turns down to add camber, usually with one or more slots. It gives the biggest increase in lift of all. From left to right the mechanism gets heavier and more complex, but the performance improves. And because flaps sit on the inboard wing, they raise the lift there, which strengthens the spanwise flow towards the root over the upper surface.
Part 2 · Trailing edge flaps
The plain flap The rear of the section is hinged and swings down as one piece Adds camber: more CL at every angle and a good rise in CL max Flow separates early over the sharply turned flap: fairly high drag Simple, light and cheap: used on low-speed aircraft that do not need very short field performance
hinge
flap 30°
faster flow over the more cambered top
Retracted outline dashed
Lift
good gain in C L max
Drag
fairly high (flow separates over the flap)
Use
light, low-speed aircraft
Chapter 13 · High Lift Devices
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The plain flap is the simplest flap: the rear part of the section is hinged and swings down as a single piece. Lowering it adds camber, so you get more lift coefficient at every angle of attack and a good rise in C L max. Watch the scene: as the flap swings down, the suction on the upper surface grows, the pressure below rises and the lift arrow gets longer, even though the angle of attack has not changed. The weakness of the plain flap is drag. The air has to turn sharply round the hinge and over the deflected flap, and at larger angles the flow separates over the flap, leaving a wide wake. That is why it gives a fairly high drag. Because it is simple, light and cheap, the plain flap is used mainly on light, low-speed aeroplanes that do not need a very short take-off and landing.
Part 2 · Trailing edge flaps
The split flap Only the lower surface plate of the trailing edge hinges down; the upper contour is unchanged About the same lift gain as a plain flap at low angles, slightly more near the stall Why: upper-surface camber is not increased, so separation is delayed Drag is higher than a plain flap : a deep, turbulent wake behind the plate Exam point: "upper surface fixed, only lower surface altered"
deep, turbulent wake
upper surface unchanged
lower plate hinges down
Lift
like plain at low α, a little more near the stall
Drag
higher than plain: deeper wake
Why
top camber not raised, separation delayed
Chapter 13 · High Lift Devices
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The split flap is a plate that forms the lower surface of the trailing edge. When it is lowered, only that plate hinges down, and the upper surface keeps exactly the same contour. That one fact is a favourite exam question. At low angles of attack the split flap gives about the same increase in lift as a plain flap. Near the stall it gives a little more, because the upper surface camber has not been increased, so the air flowing over the top does not meet a sharper curve and separation is delayed. The price is drag. Behind the plate there is a deep, turbulent wake, deeper than behind a plain flap, so the split flap has the highest drag of the four types. On older aircraft that was sometimes welcome, because it allowed steep approaches.
Part 2 · Trailing edge flaps
Slotted and multiple slotted flaps Lowering the flap opens a slot between wing and flap High-pressure air from below flows through the converging slot and out over the flap This re-energises the boundary layer and delays separation on the flap Result: a bigger rise in CL max than plain or split, with much less drag Cost: a more complex structure; double and triple slotted flaps repeat the trick
high-pressure air from below
fast air re-energises the
boundary layer over the flap
the slot converges, so the air speeds up
Triple slotted flap
each slot re-energises
the flow over the next
element
Chapter 13 · High Lift Devices
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
When a slotted flap is lowered, a gap, the slot, opens between the back of the wing and the nose of the flap. Below the wing the pressure is high and above it the pressure is low, so air flows up through the slot. The slot narrows as it goes, so the air speeds up, and it comes out as a fast sheet over the top of the flap. That fresh, energetic air is mixed into the tired boundary layer, re-energising it so it can keep following the curved flap surface instead of separating. The result is a bigger increase in C L max than either the plain or the split flap, and much less drag, because the flow stays attached. The price is a more complex structure, with tracks and fairings. Large aircraft often use double or triple slotted flaps, each slot re-energising the flow over the next element, as in the small drawing.
Part 2 · Trailing edge flaps
The Fowler flap: more area, then more camber Runs aft first, then down on tracks: first an increase in wing area , then in camber Usually slotted ; large jets use double or triple slotted Fowler flaps Gives the greatest lift increase and the least drag of the types considered Low drag: slot flow plus a lower thickness : chord ratio Largest nose-down pitching moment : the flap moves the centre of pressure further aft
Retracted
cruise
Aft first: more area
original chord
+16%
Then down: more camber
original chord
+16%
Chapter 13 · High Lift Devices
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The Fowler flap runs backwards on tracks before it turns down. In the first part of its travel it mainly moves aft, so the chord and the wing area increase. In the later part it turns down, adding camber, and a slot opens in front of it. Large jets often use double or triple slotted Fowler flaps. Because it increases both area and camber, the Fowler flap gives the greatest increase in lift of all the flaps we have looked at. It also gives the least drag, thanks to the slot and because the longer chord reduces the thickness to chord ratio. There is one important penalty. Moving the flap aft moves the centre of pressure aft as well, so the Fowler flap gives the largest change of pitching moment, nose down. If an exam question asks which flap gives the greatest change in pitching moment, the answer is the Fowler.
Part 2 · Comparing flaps
Comparing the lift curves
-12°
-8°
-4°
0°
4°
8°
12°
16°
20°
0
0.5
1
1.5
2
2.5
3
angle of attack of the basic section (degrees)
C L
Fowler
C L max 2.75 · 13°
Slotted
C L max 2.40 · 14°
Split
C L max 2.10 · 14°
Plain
C L max 2.00 · 13°
Basic section
C L max 1.45 · 16°
Same flap angle for every type.
Each type gives its best gain at
its own optimum angle.
Chapter 13 · High Lift Devices
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph compares the lift curves for the same flap angle with each type of flap. Every flap moves the curve upwards and to the left: you get more lift coefficient at every angle, the zero-lift angle becomes more negative, and C L max goes up. In this example the basic section reaches about one point four five, the plain flap about two, the split flap about two point one, the slotted flap about two point four and the Fowler flap about two point seven five. The Fowler line is also slightly steeper, because the lift coefficient is still referred to the original, smaller wing area. Notice something else: every flapped curve stalls at a lower angle of attack than the basic section. We will see why shortly. And remember the caution in the caption: the types do not all give their greatest benefit at the same flap angle, so a comparison at one angle is only a guide.
Part 2 · Flap angle
Diminishing returns from more flap The first few degrees of flap give the largest lift increments Each further step gives less extra lift ; beyond an optimum angle lift actually falls Drag does the opposite: increments get larger as the flap goes further down Small flap angles = mostly lift ; large angles = mostly drag That is why take-off uses small flap and landing uses large flap
0°
15°
30°
45°
60°
75°
0
0.5
1
Increase in C L
+0.28
+0.08
optimum
0°
15°
30°
45°
60°
75°
0
0.5
1
flap angle
Increase in C D
early flap: lift for little drag
late flap: mostly drag
Chapter 13 · High Lift Devices
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
How much extra lift do you get for each extra degree of flap? The top graph answers that. The first few degrees give the largest increase in lift coefficient. In this example the first ten degrees add about a quarter, while going from forty to fifty degrees adds only a few hundredths. Beyond an optimum angle, here about fifty five degrees, the flow can no longer follow the flap and the lift actually falls. The drag graph, underneath, does the opposite. The first few degrees add very little drag, but each further step adds more than the one before. Put the two graphs together and you have a simple rule. Small flap angles give mostly lift for little drag, which is what you want for take-off. Large flap angles give mostly drag with little extra lift, which is useful on the approach and landing.
Part 2 · Stalling angle
Higher C L max, but a lower stalling angle With flap down, CL max rises but the stalling angle falls Lowering the flap tilts the effective chord line (LE to flap TE) further into the airflow So the flap increases the effective angle of attack Lift curves are plotted against the basic section's angle, which is lower at the stall With 25° of flap here: about 5° more effective angle
relative airflow
basic chord: α = 10°
effective chord (LE to flap TE): α ≈ 15°
Flap adds about 5° of effective angle here.
The section stalls at its usual effective angle,
so on the basic chord the stall comes earlier.
Chapter 13 · High Lift Devices
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
When the flaps go down, C L max goes up, but the stalling angle of attack goes down. Why? Look at the drawing. The angle of attack is normally measured from the chord line of the basic section, the blue line. When the flap is lowered, the effective chord line runs from the leading edge to the new, lower trailing edge, the orange line, and that line is inclined more steeply to the airflow. In this example, twenty five degrees of plain flap adds about five degrees to the effective angle of attack. The wing still stalls when its effective angle reaches its critical value, but because lift curves are always drawn against the angle of the basic section, that stall shows up at a lower angle. So remember the exam pairing: with flaps lowered, the stalling angle decreases but C L max increases, and the stalling speed is lower.
Part 2 · Drag
Flap drag: a cost on take-off, a gift on landing For the same flap angle the drag varies a lot: split highest, then plain, slotted, Fowler least Take-off : drag slows the acceleration, so we want lift with little drag Landing : drag adds to the braking force, so flap drag is useful Extra drag on the approach also improves speed stability Drag increments grow with each extra degree of flap
0
0.1
0.2
0.3
0.4
0
1
2
3
C D
C L
Basic
Fowler
Slotted
Plain
Split
Further right = more drag for the same lift
Chapter 13 · High Lift Devices
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph shows drag polars, lift coefficient plotted against drag coefficient, for the same flap angle with each type of flap. The further a curve lies to the right, the more drag it gives for the same lift. The split flap gives the most drag, then the plain flap, then the slotted flap, and the Fowler flap gives the least while also giving the most lift. Whether that drag is good or bad depends on the phase of flight. On take-off, drag reduces the acceleration along the runway, so we want the flap to give lift with as little drag as possible. On landing, drag adds to the braking force and helps you stop, so flap drag is welcome. On the approach, the extra drag also improves speed stability, because the aircraft is further from the minimum drag speed. And remember, the drag increments grow larger as the flap angle increases.
Part 2 · Lift / drag ratio
Flaps reduce the maximum L/D Flap raises both lift and drag, but drag rises proportionally more So (L/D)max decreases with flap Best L/D: the tangent from the origin to the polar; its slope is the ratio With flap: range down , climb angle down , glide angle steeper Here: clean about 17, flaps down about 9
0
0.1
0.2
0.3
0
0.5
1
1.5
2
2.5
C D
C L
clean: L/D max ≈ 17
flaps down: L/D max ≈ 9
Tangent from the origin: its slope is the best L/D
Chapter 13 · High Lift Devices
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Lowering flap increases both the lift and the drag, but not in the same proportion. Lift is still the bigger force, but in percentage terms the drag goes up more, so the maximum lift to drag ratio falls. You can see it on the drag polar. Draw a line from the origin that just touches the curve: the point where it touches is the best lift to drag ratio, and the slope of the line is the value. In this example the clean tangent gives a ratio of about seventeen, while with flaps down it is only about nine. The lift to drag ratio is a measure of aerodynamic efficiency, so with flaps down the range is reduced, the climb angle is reduced, and the glide angle is increased. With a ratio of seventeen the glide angle is about three and a half degrees; at nine it is a little over six degrees.
Part 2 · Pitching moment
Two effects on pitch: centre of pressure and downwash
1 · Centre of pressure moves aft
2 · More downwash at the tail
3 · Net result depends on design
CP flap up
CP flap down
aft
NOSE DOWN
Fowler: the flap also moves aft → even more
downwash increases
tail force
more downward
NOSE UP
Low tail in downwash
up, down or ≈ 0
T-tail above wake
NOSE DOWN
Fowler flap
larger nose down
Pilot
retrim after each change
Chapter 13 · High Lift Devices
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Moving the flaps up or down usually changes the pitching moment, for two reasons. First, the centre of pressure. A trailing edge flap changes the pressure over the whole chord, but most of all near the flap, so when it is lowered the centre of pressure moves aft and the wing gives a nose-down pitching moment. A Fowler flap also moves the lifting surface aft, so its nose-down change is the largest. Second, the downwash. Lowering the flaps increases the downwash behind the wing. A tailplane sitting in that downwash meets the air at a smaller angle of attack, so it pushes down harder, and that gives a nose-up pitching moment. The overall result depends on which effect wins, so it can be nose up, nose down or almost nothing. A T-tail on top of the fin sits above most of the extra downwash, so with a T-tail the nose-down effect usually dominates. Either way, the pilot retrims.
Part 2 · Attitude
Flaps down, nose down In steady flight lift = weight Lower flap at constant speed and lift rises, so the angle of attack must be reduced The aircraft flies in a more nose-down attitude with flap On the approach this gives a better view of the runway Exam: flaps lowered at constant IAS, level flight → reduce α
same lift
Clean: α ≈ 8°
same lift
Flap down: α ≈ 3°
Same speed, same lift: flap lets the nose come down
Chapter 13 · High Lift Devices
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
In steady, level flight the lift must equal the weight. Suppose you lower the flaps but keep the speed the same. The flap raises the lift coefficient at every angle of attack, so at the old angle the lift would now be more than the weight and the aircraft would climb. To keep the lift at its original value, you must reduce the angle of attack. Watch the scene: the flaps come down and the nose is lowered, while the lift stays equal to the weight. So with flaps down the aircraft flies in a more nose-down attitude. On the approach that is a real advantage, because it gives the pilot a better view of the runway and the landing area. This is a classic exam question: if flaps are lowered with the airspeed kept constant, then to stay in level flight the angle of attack must be reduced.
Part 3 · Leading edge devices
Krueger and variable camber flaps High-speed sections have little nose camber and a small leading edge radius : flow can separate just behind the nose at quite low angles A leading edge flap adds nose camber to stop this Krueger flap : part of the lower surface near the nose hinges forward about its front edge Krueger flaps are less efficient, so they go inboard on swept wings to make the root stall first Variable camber (droop) flaps curve as they extend; LE devices are fully out or stowed
Krueger flap
panel swings forward
about its front edge
stowed position (dashed)
Variable camber (droop) flap
nose droops and curves
Either fully extended or stowed: no in-between
Chapter 13 · High Lift Devices
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now to the leading edge. A high speed section often has very little camber at the nose and a small leading edge radius. At low speed and quite low angles of attack the air cannot get round that sharp nose, and it separates just behind the leading edge. The cure is a leading edge flap, which adds camber at the nose. The Krueger flap is a panel from the lower surface near the leading edge that swings down and forward about its front edge, forming a new, blunter nose. It is simple but less efficient than the alternatives, so on swept wings it is often used on the inboard section, where a weaker device helps the root stall first. A variable camber leading edge flap droops the nose and curves it as it extends, giving a better profile. Unlike trailing edge flaps, leading edge devices are normally either fully extended or stowed, with no intermediate positions.
Part 3 · Leading edge devices
What a leading edge flap does to the lift curve Main effect: delays separation at the nose So the stalling angle rises , and with it CL max Some extra lift at low angles too, from the added camber Compare: a TE flap moves the curve up and left ; a LE device extends it upwards Drag and pitch changes from LE devices are small
-5°
0°
5°
10°
15°
20°
25°
0
0.5
1
1.5
2
angle of attack
C L
basic thin section
with LE flap
small gain from camber
Main effect: separation delayed to a higher angle
Chapter 13 · High Lift Devices
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
What does a leading edge flap do to the lift curve? Its main effect is to delay separation at the nose. The basic thin section in this graph stalls at about twelve degrees with a C L max of about one point one. With the leading edge flap, the flow stays attached until about twenty two degrees, so the curve simply carries on climbing to a C L max of about one point seven five. There is a small increase in lift at lower angles as well, because the flap does add some camber, but that is a minor effect. Compare this with a trailing edge flap. A trailing edge flap shifts the whole curve up and to the left and lowers the stalling angle. A leading edge device mainly extends the curve to a higher stalling angle. And compared with trailing edge flaps, the changes in drag and pitching moment from leading edge devices are small.
Part 3 · Leading edge devices
Slats and slots A slot is a gap from the lower surface to the upper surface near the leading edge; it can be fixed or made by moving a slat forward A slat is a small, cambered auxiliary aerofoil on the leading edge The slot forms a convergent duct : air accelerates and adds kinetic energy to the boundary layer Separation is delayed until about 25° A fixed slot adds drag at speed, so slats are usually closed for cruise , opened with the flap selector
high pressure below
flow stays attached
slat
Convergent slot
air speeds up: kinetic energy added
Boundary layer
re-energised, beats the adverse gradient
Stall
delayed to roughly 25°
Chapter 13 · High Lift Devices
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
A leading edge slot is a gap that runs from the lower surface to the upper surface just behind the leading edge. It can be fixed, built into the wing, or it can be created by moving part of the leading edge, called the slat, forward. A slat is a small, well cambered auxiliary aerofoil. Watch the slats run forward and down along the leading edge. Air from the high pressure region below the wing now flows through the gap to the low pressure region above. Because the gap narrows, it is a convergent duct, so the air speeds up and adds kinetic energy to the boundary layer on the upper surface. With that extra energy the boundary layer can push against the adverse pressure gradient to much higher angles, separating only at about twenty five degrees. A permanently open slot would add drag at high speed, so most slats are closed in the cruise and opened with the flaps, from the same selector.
Part 3 · How the slat works
The slat prolongs the lift curve by flattening the suction peak
0°
5°
10°
15°
20°
25°
30°
0
0.5
1
1.5
2
angle of attack
C L
wing + slats: C L max 2.0 at 25°
wing: C L max 1.5 at 15°
0
0.25
0.5
0.75
1
0
2
4
6
position along the chord (x / c)
Suction on the upper surface (−C p)
no slat: sharp peak, steep adverse gradient
with slat: flatter peak, similar area
Chapter 13 · High Lift Devices
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is what the slat does in numbers and in pressures. On the left, the wing alone reaches a C L max of about one point five at about fifteen degrees. With slats the lift curve follows the same straight line but simply carries on, to about two point nought at about twenty five degrees. On the right are the upper surface pressures at a high angle of attack. Without the slat there is a tall, sharp suction peak right at the leading edge, followed by a very steep adverse pressure gradient that thickens the boundary layer and makes it separate. The slat, which is itself working hard because of its marked camber, flattens that peak into a lower, broader hump with a gentler gradient. The area under the curve, which tells you the lift, is about the same or even more. And because the suction peak does not move forward, the slat has very little effect on the pitching moment.
Part 3 · Automatic slats
Automatic slats and the drawback of slots Some slats move by aerodynamic forces alone , no pilot input Low α: high pressure near the stagnation point holds the slat closed High α: the stagnation point moves under the nose ; suction on the slat pulls it open Used on small aircraft as stall protection; large aircraft select slats electrically or hydraulically Drawback: a slot gives its CL max only at a very high angle , so a nose-high attitude and poor view
Low α: held closed
stagnation point
pressure pushes slat in
High α: pulled open
stagnation point
now under the nose
suction on slat
No pilot input: aerodynamic forces work the slat
Used on small aircraft as stall protection.
Large aircraft: slats selected, moved by hydraulics or motors.
Chapter 13 · High Lift Devices
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
On some aircraft the slats are not controlled by the pilot at all; they move on their own. At low angles of attack the stagnation point sits right on the nose of the slat, and the high pressure there holds the slat closed. As the angle of attack increases, the stagnation point moves back underneath the leading edge, as you can see in the scene, and strong suction develops over the top of the slat. That suction pulls the slat forward on its rails and opens the slot. Automatic slats are used mainly on small aircraft as a form of stall protection; on large aircraft the crew selects the slats, which are driven electrically or hydraulically. A slot does have one drawback. It can give an increase in C L max similar to a trailing edge flap, but only at a much higher angle of attack, so the aircraft would be very nose-high at low speed, spoiling the view of the runway on the approach.
Part 3 · Together
Leading and trailing edge devices together Most large transports use both leading and trailing edge devices TE flap: curve moves up and left ; slot or slat: curve extends to a higher stalling angle Together they give the highest CL max , here about 3.0 LE devices are also used for take-off : they raise CL max at any flap setting LE devices counter the nose-high attitude a slot alone would need
-15°
-10°
-5°
0°
5°
10°
15°
20°
25°
30°
0
1
2
3
angle of attack of basic section
C L
basic
basic + slot
TE flap
flap + slot
Chapter 13 · High Lift Devices
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Most large transport aircraft use both leading edge and trailing edge devices. Watch the scene: the slats run out along the leading edge first, then the trailing edge flaps extend in stages. On the graph you can see how the effects combine. The trailing edge flap moves the lift curve up and to the left, adding camber and area. The slot or slat extends a curve to a higher stalling angle. Put them together and you get the highest C L max of all, about three in this example, and the slat also stops the flapped wing stalling at too low an angle. Leading edge devices are normally used for take-off as well as landing, because they raise C L max whatever trailing edge flap setting is chosen. And the combination avoids the very nose-high attitude that a slot on its own would need.
Part 4 · Operation
Leading edge first out, last in Lowering a TE flap increases downwash behind and upwash ahead of the wing On a high-speed section already at a fairly high α, the extra upwash could stall the leading edge So extend : leading edge devices first , then trailing edge flaps Retract : trailing edge flaps first , then leading edge devicesUsually automatic, sequenced by the single flap selector
Extending
1 · Leading edge out
2 · Trailing edge down
Retracting
1 · Trailing edge up
2 · Leading edge in
Why: TE flap increases the upwash at the nose
stronger upwash: the nose meets
the air at a higher angle
thin high-speed nose may stall
Chapter 13 · High Lift Devices
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
For some wings the order in which the devices move really matters. When a trailing edge flap is lowered, it increases the downwash behind the wing, and it also increases the upwash ahead of it. The air meets the nose at a steeper angle, so the local angle of attack at the leading edge goes up. On a thin high speed section that is already at a fairly high angle of attack, that extra upwash could make the leading edge stall. So the rule is simple. When extending, the leading edge devices go out first, and then the trailing edge flaps come down. When retracting, it is the reverse: the trailing edge flaps come up first, and only then are the leading edge devices stowed. In other words, the leading edge is first out and last in. On modern aircraft this sequencing is built into the system, driven by a single flap lever.
Part 4 · Protection
Asymmetry and flap load relief
more lift, more drag
less lift
left flap down
right flap failed up
Rear view
ROLL toward the clean wing · YAW toward the flapped wing
Asymmetry Unequal flaps: the flapped wing makes more lift (roll away) and more drag (yaw toward it).
Pilot action Hold aileron against the roll and rudder against the yaw; control may run out.
Asymmetry protection Systems compare both sides while moving and stop the flaps if one side fails.
Flap load relief Selected above VFE ? Flaps will not run until the speed falls, then extend.
Chapter 13 · High Lift Devices
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
High lift devices produce large changes in lift, drag and pitching moment, so if they move unequally on the two wings, the result can be a serious roll control problem. In the drawing the left flap is down and the right one has failed up. The flapped wing makes more lift, so the aircraft rolls towards the clean wing, and it makes more drag, so the aircraft yaws towards the flapped wing. The pilot has to hold aileron against the roll and rudder against the yaw, and with a large asymmetry the controls may not be enough. Many systems therefore compare the two sides while the flaps are moving, and stop both if one side fails. Large jets also have flap load relief. The pilot can select flap above the flap extension speed, V F E, but the flaps will not move until the speed has fallen to a safe value, and then they extend automatically.
Part 4 · Flap settings
Choosing the flap for take-off, climb and landing Take-off : big flap gives a low unstick speed but high drag and slow acceleration; small flap the reverseSo there is an optimum take-off flap for the shortest distance; LE devices are used too Climb : flap reduces the climb gradient, so if climb is limiting use less flap , accepting a longer runLanding : large flap for the lowest touchdown speed and high drag to decelerateLanding uses LE devices too, for the highest CL max
-12°
-8°
-4°
0°
4°
8°
12°
16°
20°
0
1
2
C L
landing 30°
take-off 20°
flaps up
-12°
-8°
-4°
0°
4°
8°
12°
16°
20°
0
0.1
0.2
0.3
angle of attack
C D
Chapter 13 · High Lift Devices
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Which flap setting should you use? For take-off, the distance depends on the unstick speed and on how quickly you accelerate to it. A large flap angle gives the highest C L max and so the lowest unstick speed, but it also gives a lot of drag, which slows the acceleration. A small flap angle gives a higher unstick speed but better acceleration. Somewhere in between is an optimum setting that gives the shortest take-off distance, and leading edge devices are used as well because they raise C L max at any flap setting. After take-off, a minimum climb gradient is required, and flap reduces the climb gradient. So if climb is the limit, you may choose less flap and accept a longer take-off run. For landing, there is no conflict: a large flap angle gives the lowest touchdown speed and plenty of drag to slow down, so large flap and leading edge devices are used.
Part 4 · Management
Flying the lift curve: flaps up and flaps down
Retracting after take-off
-4°
0°
4°
8°
12°
16°
20°
0
0.5
1
1.5
2
2.5
angle of attack
C L
flaps extended
flaps up
A
B
C
retract at A: sinks
1 · accelerate A → B 2 · retract and raise α, B → C
Extending before landing
-4°
0°
4°
8°
12°
16°
20°
0
0.5
1
1.5
2
2.5
angle of attack
C L
flaps extended
flaps up
A
B
C
extend at A: balloons
1 · extend and lower α, A → B 2 · slow down B → C
Chapter 13 · High Lift Devices
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us fly the lift curve. On the left, just after take-off, you are at point A on the flaps-extended curve. If you retracted the flaps there, at the same angle and speed, the lift coefficient would drop to the clean curve and the aircraft would sink. So first accelerate, moving down the flap curve to point B. Then retract, raising the angle of attack to point C on the clean curve so that the lift coefficient stays the same. Retracting also removes drag, which helps the acceleration. When gross weight and density altitude are high, acceleration is poor and that increase in angle is noticeable. On the right, before landing, you are level at point A on the clean curve. Extend the flaps at that angle and you jump to C: the aircraft balloons. Instead, lower the nose to B as the flaps extend, keeping the lift coefficient the same, then let the aircraft slow down to C.
Summary
High lift devices: what to take into the exam Purpose Higher CL max → lower VS → shorter take-off and landing; VS ∝ 1/√CL max .
TE flap effects CL max up, stalling angle down , stall speed down, L/D max down, nose-down attitude.
Flap types Lift: Fowler > slotted > split ≥ plain. Drag: split highest, Fowler least.
Pitch CP aft = nose down (Fowler most); more downwash at tail = nose up. T-tail: nose down.
LE devices Delay separation: stalling angle and CL max up; small drag and pitch change.
Slats Convergent slot re-energises boundary layer; stall near 25°; flattens suction peak.
Operation LE first out, last in. Asymmetry: roll away, yaw toward the flapped wing. Load relief at VFE .
Handling Retract: accelerate, then raise α. Extend: lower α, then slow. Otherwise sink or balloon.
Chapter 13 · High Lift Devices
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it together. High lift devices raise C L max, which lowers the stalling speed and so shortens take-off and landing distances; speed goes with one over the square root of C L max. Trailing edge flaps raise C L max but lower the stalling angle; they reduce the maximum lift to drag ratio and make the aircraft fly more nose down. For lift, the Fowler is best, then slotted, then split and plain; for drag, split is worst and Fowler is least. Flap moves the centre of pressure aft, nose down, and increases downwash at the tail, nose up; a T-tail usually ends up nose down. Leading edge devices delay separation, raising the stalling angle and C L max with little change of drag or pitch. Slats re-energise the boundary layer. Leading edge out first and in last. Retract flaps only after accelerating, and lower the nose when extending, or you will sink or balloon.