Principles of Flight · Chapter 8
Induced Drag The drag that comes with lift: spanwise flow, wingtip vortices, downwash and the induced angle, and how speed, weight, aspect ratio, planform and the ground change it.
downwash left tip: clockwise right tip: anticlockwise viewed from behind © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to chapter eight, on induced drag. In the last lesson we met parasite drag, the drag that has nothing to do with lift. Now we meet its partner, the drag that exists only because the wing is making lift. You will see how the pressure difference between the top and bottom of a wing spills round the wingtips into powerful vortices, how those vortices tilt the airflow and the lift backwards, and why that tilt costs drag. Then we look at what makes induced drag bigger or smaller, from speed and weight to aspect ratio, winglets and the wing planform, and finish with the curious behaviour of a wing flying close to the ground.
Lesson map
Induced drag in four steps 1 · The cause Spanwise flow , wingtip vortices , upwash and downwash .
2 · The geometry The induced angle tilts lift back: its rearward part is induced drag .
3 · The factors Speed , weight and load factor, aspect ratio , planform .
4 · Reducing it Winglets , end-plates, tip tanks, twist, and ground effect .
Chapter 8 · Induced Drag
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through induced drag. First, the cause: how the pressure difference that makes lift drives air round the wingtips, forming vortices that change the upwash and downwash around the wing. Second, the geometry: how that extra downwash tilts the lift backwards through the induced angle, and why the rearward part of the lift is induced drag. Third, the factors: speed, weight and load factor, aspect ratio and the planform of the wing, with the numbers you need for the exam. Finally, the ways of reducing induced drag, such as winglets, end-plates, tip tanks and wing twist, and the special case of flying close to the ground, which we call ground effect.
The cause
Induced drag: the price of lift Induced drag is an unavoidable by-product of lift : no lift, no induced dragWingtip vortices modify the upwash and downwash round the wingThat gives the lift a rearward component : induced drag The lower the IAS , the higher the angle of attack , the stronger the vortices The stronger the vortices, the greater the induced drag 1 Lift low pressure above, high below 2 Spanwise flow air spills round the tips 3 Wingtip vortices stronger at low IAS, high α 4 More downwash effective α reduced 5 Lift tilts back by the induced angle 6 Induced drag the rearward part of lift
Chapter 8 · Induced Drag
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Induced drag is the drag that comes with lift. It is an unavoidable by-product: whenever a wing makes lift, it makes induced drag, and if there were no lift there would be none. The story runs in six steps, shown on the right. To make lift, the wing has lower pressure above and higher pressure below. At the wingtips, air spills from the high pressure underneath to the low pressure on top, creating spanwise flow. That flow rolls up into wingtip vortices. The vortices strengthen the upwash ahead of the wing and the downwash behind it, which reduces the effective angle of attack. As a result, the lift is tilted backwards, and its rearward component is the induced drag. Keep two rules in mind for the whole lesson: the lower the IAS, the higher the angle of attack and the stronger the vortices; and the stronger the vortices, the greater the induced drag.
The cause 1
Spanwise flow over a finite wing The upper surface is at lower pressure than the lower surface At the tips and trailing edge , air flows from high pressure to low On top the flow is turned inboard , towards the root Underneath it is turned outboard , towards the tip The two streams meet at the trailing edge at an angle and roll up into vortices near the tips airflow upper surface: turned INBOARD lower surface: turned OUTBOARD curls round the tip
Chapter 8 · Induced Drag
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look at the first step more closely. To make lift, the air over the upper surface is at a lower pressure than the air underneath. On a wing of infinite span that would be the end of it, but a real wing has tips. At the tips, and along the trailing edge, the high-pressure air from below is free to move towards the low pressure above. This pressure difference changes the direction of the flow over the whole wing, not just at the tips. On the upper surface the flow is turned slightly inboard, towards the root. On the lower surface it is turned slightly outboard, towards the tip. When the two streams leave the trailing edge they meet at an angle, forming a twisting sheet of air, and near the tips this sheet rolls up into a concentrated vortex. In the animation, orange arrows on top point inboard and blue arrows underneath point outboard.
The cause 2
Wingtip vortices and their direction LEFT TIP clockwise RIGHT TIP anticlockwise downwash between the vortices upwash upwash VIEWED FROM BEHIND Viewed from behind : left tip clockwise , right tip anticlockwise . Up outboard of the tips, down between them.
Chapter 8 · Induced Drag
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the vortices viewed from behind, which is the conventional way to describe them. Air flows outwards under the wing, curls up round each tip, and flows inwards over the top. So, seen from behind, the vortex at the left wingtip rotates clockwise and the vortex at the right wingtip rotates anticlockwise. Work it out once for yourself: under the right wing the air moves to the right, then up round the tip, then to the left over the top, and that is anticlockwise. Look at what the two vortices do to the air around them. Between the vortices, behind the wing, the air is pushed down: that is downwash. Outboard of the tips the air is moving up. The vortices trail behind the aircraft for several miles and sink slowly, which is the wake turbulence that air traffic separation is designed to protect against.
The cause 3
What makes the vortices strong At high angle of attack (low IAS) the chordwise flow is slower The same spanwise push then turns the flow through a bigger angle So the vortices are strongest when the aircraft is heavy , clean and slow That is exactly the take-off and approach: the worst wake turbulence Lower α, higher IAS: weaker vortices High IAS, low α chordwise spanwise resultant turned 14° weak vortex Low IAS, high α chordwise spanwise resultant turned 39° STRONG vortex
Chapter 8 · Induced Drag
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
How strong the vortices are depends on how much the flow is twisted. Think of the air over the wing as having two velocity components: a chordwise component, flowing back over the wing, and a spanwise component, driven by the pressure difference. At high speed and low angle of attack the chordwise flow is fast, so the spanwise push only turns the flow through a small angle, and the vortex is weak. At low speed and high angle of attack, the chordwise flow is slower, so the resultant is turned much more, and the vortex is strong. Add weight, which needs more lift and a bigger pressure difference, and a clean wing, with no flaps to spread the lift, and you have the strongest vortices of all: heavy, clean and slow. That describes an airliner just after take-off or on the approach, which is why wake turbulence separation matters most near airports.
The cause 4
Upwash, downwash and the effective angle Any lifting wing has upwash ahead of it and downwash behind it The tip vortices strengthen both , especially over the outer span The air reaching the wing is inclined downwards : the effective airflow So the wing works at a smaller effective angle of attack The stronger the vortices, the bigger the reduction, and the less lift for a given α UPWASH ahead DOWNWASH behind Tip vortices strengthen both, most of all towards the wingtips The air meeting the wing is inclined downwards: the effective angle of attack is reduced
Chapter 8 · Induced Drag
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every lifting wing bends the airflow: it lifts the air slightly ahead of it, called upwash, and pushes the air down behind it, called downwash. On a finite wing, the tip vortices add their own vertical velocities to this pattern, strengthening both the upwash and the downwash, most of all over the outer part of the span. The net effect at the wing is that the air arriving at each section is inclined downwards compared with the free stream. We call that inclined flow the effective airflow. The wing section only feels the effective airflow, so it works at a smaller effective angle of attack than the geometric angle between the chord and the relative airflow. That means less lift than you would get with no spanwise pressure difference at all. In a sense, making lift reduces the lift being made. The stronger the vortices, the bigger this loss.
The geometry
The induced angle tilts the lift back chord relative airflow effective airflow α αi αe lift with no extra downwash LIFT ⟂ to the effective airflow INDUCED DRAG rearward component of lift αi α = geometric angle of attack αi = induced angle (downwash) αe = α − α i = effective angle Di ≈ L × α i (α i in radians) angles exaggerated for clarity Lift is perpendicular to the effective airflow, so it leans back by αi . Its component parallel to the relative airflow is induced drag.
Chapter 8 · Induced Drag
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
This diagram is the heart of the lesson, so take it slowly. The relative airflow arrives horizontally, and the chord is at the geometric angle of attack, alpha. Because of the extra downwash, the effective airflow at the wing is deflected down by a small angle called the induced angle of attack. The effective angle of attack is therefore alpha minus the induced angle. Now, the lift a wing section produces is always perpendicular to the airflow it actually feels, the effective airflow. So the lift vector is tilted backwards by the induced angle, compared with a lift vector perpendicular to the relative airflow. Resolve that tilted lift into two parts. The part perpendicular to the relative airflow is the useful lift supporting the weight. The part parallel to the relative airflow, pointing rearwards, is induced drag. For small angles, induced drag is roughly the lift times the induced angle in radians.
The geometry 2
Replacing the lost lift costs drag Downwash steals part of the angle: less lift at a given α To get the lift back the wing must fly at a higher α than an infinite wing would need A higher α means a bigger rearward tilt: that extra drag is induced drag The finite wing's lift curve is less steep than the section's The lower the aspect ratio, the flatter the lift curve 0 4 8 12 16 0.4 0.8 1.2 α (°) CL extra α ≈ αi section (infinite span) finite wing CL = 0.8: section needs 5.3°, AR 7 wing needs 7.6°
Chapter 8 · Induced Drag
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the downwash steals part of the angle of attack, the finite wing makes less lift at any given geometric angle than its section would on an infinite span. To recover the lift it needs, the wing has to be flown at a higher angle of attack than would otherwise be necessary. And a higher angle, with stronger downwash, means the lift is tilted back further. That extra drag is induced drag. You can see the effect on the lift curve. The grey dashed line is the basic section, an infinite wing. The blue line is a real wing of aspect ratio seven. To make a lift coefficient of nought point eight, the section needs about five point three degrees, but the finite wing needs about seven and a half. The difference is roughly the induced angle. So the finite wing has a less steep lift curve, and, as we will see, the lower its aspect ratio, the flatter that curve becomes.
The factors
What decides the size of induced drag Lift Di ∝ L² . More weight or more load factor (turns, pull-ups): more Di .
Speed For a given lift, Di ∝ 1 / V² . Faster: less downwash tilt, less Di .
Aspect ratio CDi ∝ 1 / AR . Tips affect a smaller share of a long, slender wing.
Planform Elliptical lift distribution is best; taper, washout and tip devices help.
Chapter 8 · Induced Drag
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Four things decide how much induced drag there is. First, the size of the lift. Induced drag is a component of the lift force, so the more lift, the more induced drag; in fact it goes with the square of the lift. In level flight lift equals weight, so a heavier aircraft has more induced drag, and in a turn or a pull-up, where the load factor is greater than one, induced drag rises too. Second, speed. For a given lift, induced drag falls as speed rises, in proportion to one over the speed squared, because the downwash becomes less significant and the lift is tilted back less. Third, aspect ratio. The induced drag coefficient is inversely proportional to aspect ratio. Fourth, the planform and the spanwise lift distribution, where an elliptical distribution is the ideal. We take each in turn.
Speed 1
The induced drag formula Di = ½ ρ V² · CDi · S CDi ∝ CL ² / AR (exactly CL ² / π e AR)In level flight, as speed rises CL must fall to keep lift = weight CDi falls with the square of CL , much faster than ½ρV² grows Net result: Di ∝ 1 / IAS² for a given weight Di = ½ ρ V² · C Di · S CDi ∝ C L ² / AR exactly: CDi = C L ² / (π · e · AR) e ≈ 1 for an elliptical lift distribution The formula looks as if Di grows with V², but: • to keep L = W, CL must fall as V rises (C L ∝ 1/V²) • so CDi ∝ 1/V⁴, while ½ρV² ∝ V² Di ∝ L² / V² (∝ W² / IAS² in level flight) for a given lift, Di ∝ 1 / AR
Chapter 8 · Induced Drag
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Like parasite drag, induced drag can be written as half rho V squared, times a coefficient, times the wing area. At first glance that suggests induced drag grows with speed, but there is a catch. The induced drag coefficient is proportional to the lift coefficient squared, divided by the aspect ratio. More exactly, it is C L squared over pi times e times the aspect ratio, where e is an efficiency factor equal to one for an ideal elliptical lift distribution. Now think about level flight. As speed rises, the dynamic pressure rises, so the lift coefficient must come down to keep lift equal to weight. The lift coefficient falls with one over V squared, so the induced drag coefficient, which depends on its square, falls with one over V to the fourth. Multiply by half rho V squared and the overall result is that induced drag is proportional to one over the IAS squared, for a given weight.
Speed 2
Worked example: double the speed Level flight, constant weight, sea level ISA (ρ = 1.225 kg/m³). Speed doubled from 80 kt (≈ 41 m/s) to 160 kt (≈ 82 m/s):
Quantity 80 kt 160 kt Change Dynamic pressure Q = ½ρV² 0.5 × 1.225 × 41² ≈ 1030 Pa 0.5 × 1.225 × 82² ≈ 4118 Pa × 4 Lift coefficient CL (L = Q CL S constant) CL ¼ CL × ¼ Induced drag coefficient CDi ∝ CL ² CDi (¼)² = 1/16 CDi × 1/16 Induced drag Di = Q CDi S Di 4 × 1/16 = ¼ Di × ¼ Speed halved instead (160 → 80 kt) Q × ¼, CL × 4, CDi × 16 Di × 4
Remember the chain for the exam: speed × 2 → Q × 4 → CL × ¼ → CDi × 1/16 → Di × ¼. Any constant density gives the same ratios.
Chapter 8 · Induced Drag
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us prove the inverse square law with numbers. Our aircraft doubles its speed in level flight from eighty knots, about forty-one metres per second, to one hundred and sixty knots, about eighty-two metres per second. At sea level the dynamic pressure goes from about one thousand and thirty pascals to about four thousand one hundred and eighteen pascals, four times as much. Lift must stay equal to weight, so the lift coefficient must fall to one quarter. The induced drag coefficient depends on the lift coefficient squared, so it falls to one quarter squared, one sixteenth. Induced drag is the dynamic pressure times the coefficient, so four times one sixteenth gives one quarter. Doubling the speed quarters the induced drag. Run it the other way, halving the speed, and you get a quarter of the dynamic pressure, four times the lift coefficient, sixteen times the induced drag coefficient and four times the induced drag. Learn that chain; it appears in exams.
Speed 3
Induced drag falls as IAS rises 40 80 120 160 200 1 4 16 IAS (kt) induced drag (units) × 2 speed → × ¼ Di × ½ speed → × 4 Di Inverse square law IAS × 2 Di × ¼ IAS × ½ Di × 4 IAS × 3 Di × 1/9 IAS + 10 % Di − 17 % IAS − 20 % Di + 56 % ratio of Di = 1 / (ratio of speeds)² Induced drag dominates at low IAS : at low speed it can be more than half the total drag.
Chapter 8 · Induced Drag
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the curve of induced drag against IAS for one weight in level flight. It is the mirror image of the parasite drag curve: very high at low speed, falling rapidly as speed increases. At eighty knots our aircraft has four units of induced drag. At one hundred and sixty knots it has one unit, a quarter. Down at forty knots, if it could fly that slowly, it would have sixteen units. For smaller changes, use one over the square of the speed ratio. Ten per cent faster gives one over one point two one, about seventeen per cent less induced drag. Twenty per cent slower gives one over nought point six four, about fifty-six per cent more. So induced drag is the dominant drag at low speed, typically more than half of the total, which is why it matters so much for take-off, climb and the approach, and much less at high cruising speed.
Weight and load factor
Heavier, or pulling g: more induced drag Di ∝ L² ; in level flight L = W, so Di ∝ W² 10 % heavier: 1.1² = 1.21 , so about 21 % more induced drag at the same IAS Load factor n = L / W. In a level turn n = 1 / cos(bank)60° bank : n = 2, so four times the induced drag at the same IASBurning fuel makes the aircraft lighter: induced drag falls through the flight Induced drag at the same IAS Level, normal weight n = 1 × 1 10 % heavier L × 1.1 × 1.21 Level turn, 60° bank n = 2 × 4 Di ∝ L²: n = 1 / cos(bank) 60° bank: n = 2, so Di × 4
Chapter 8 · Induced Drag
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because induced drag goes with the square of the lift, weight has a strong effect. In level flight lift equals weight, so induced drag is proportional to weight squared. An aircraft ten per cent heavier needs ten per cent more lift, and one point one squared is one point two one, so it has about twenty-one per cent more induced drag at the same IAS. The same applies whenever the lift has to exceed the weight. The ratio of lift to weight is the load factor, sometimes called g. In a level turn the load factor is one over the cosine of the bank angle. At sixty degrees of bank, the cosine is one half, so the load factor is two, and the induced drag at the same IAS is four times as great. That is why you need extra power to hold speed in a steep turn. On the bright side, as fuel burns off during a flight, the weight falls and so does the induced drag.
Aspect ratio 1
Aspect ratio Aspect ratio = span ÷ mean chord = span² ÷ wing area On a high AR wing the tip vortices affect a smaller share of the span Less overall downwash, smaller rearward tilt: less induced drag for a given lift CDi ∝ 1 / AR : double the AR, halve CDi Most valuable for aircraft that cruise at high CL , such as jet transports and gliders AR = span ÷ mean chord = span² ÷ area Aircraft 1 22.5 m × 4 m AR 5.6 Aircraft 2 45 m, 90 m² (c̄ = 2 m) AR 22.5 Aircraft 3 30 m × 3 m AR 10 Aircraft 4 40 m, 90 m² (c̄ = 2.2 m) AR 17.8 highest AR: aircraft 2 · lowest AR: aircraft 1
Chapter 8 · Induced Drag
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aspect ratio is the span divided by the mean chord, or, which is the same thing, the span squared divided by the wing area. A long, slender wing has a high aspect ratio; a short, stubby wing has a low one. On a high aspect ratio wing, the tip vortices only affect a small proportion of the span, so the overall change in downwash is less, the rearward tilt of the lift is smaller, and induced drag is reduced for the same lift. The induced drag coefficient is inversely proportional to aspect ratio, so doubling it halves the coefficient. Try the four aircraft on the right. Aircraft one: twenty-two point five metres span, four metres chord, aspect ratio about five point six. Aircraft two: forty-five metres span and ninety square metres, so forty-five squared over ninety, twenty-two point five. Aircraft three: ten. Aircraft four: forty squared over ninety, about seventeen point eight. Aircraft two has the highest, and aircraft one the lowest.
Aspect ratio 2
Aspect ratio on the lift curve and the drag polar 0 5 10 15 20 25 30 0.4 0.8 1.2 wing α (°) CL higher AR: steeper, stalls at a smaller α ∞ 18 12 5 2 AR AR 0.05 0.10 0.15 0.20 0.25 0.4 0.8 1.2 wing CD CL ∞ 18 12 5 2 higher AR: less drag for the same CL High AR: steeper lift curve , smaller α for CL max , and less drag at every CL , most of all at high CL (low IAS).
Chapter 8 · Induced Drag
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aspect ratio shows up clearly on two graphs. On the left are lift curves for the same section built into wings of different aspect ratio, from infinite down to two. The higher the aspect ratio, the steeper the curve: a high aspect ratio wing is more sensitive to angle of attack, and it reaches its maximum lift at a smaller angle. The very low aspect ratio wing has a flat curve and needs a large angle to reach the same lift. On the right are the drag polars, lift coefficient against drag coefficient. At any lift coefficient, the higher aspect ratio wing has the lower drag coefficient, because the induced drag coefficient varies inversely with aspect ratio. Notice that at low lift coefficients the curves are close together, but at high lift coefficients, which means low IAS, the low aspect ratio wing's drag rises very rapidly. So a high aspect ratio pays off most at high angles of attack.
Aspect ratio 3
Why not make the wing even longer? tip moves down tip moves up roll down-going wing: α rises → resists the roll longer span → faster tip → stronger damping Bending moment A long wing has a large root bending moment . Eased by fuel in the wings and podded engines under them.
Slower roll The down-going tip meets a higher effective α that resists the roll (aerodynamic damping), worst at low IAS .
Ground clearance Long wings leave less clearance when banked during take-off and landing.
Chapter 8 · Induced Drag
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
If high aspect ratio is so good, why not make every wing like a glider's? There are three practical limits. First, structure. A long wing has a very large bending moment at the root, which means a heavy structure. Designers ease it by carrying fuel in the wings and hanging the engines in pods beneath them, so their weight counters the lift. Second, roll rate. When the aircraft rolls, the down-going wing is moving downwards, so its airflow comes from below and its effective angle of attack rises, producing extra lift that opposes the roll. This is called aerodynamic damping. The longer the span, the faster the tip moves for a given roll rate, so the stronger the damping, and the effect is worst at low airspeed. Third, ground clearance: a long wing leaves little room under the tip when the aircraft is banked during take-off and landing. So aspect ratio is always a compromise.
Reducing induced drag
Weakening the tip vortex End-plate Tip tank Winglet Shaped tip all weaken the tip vortex (front view, right wingtips) End-plates Restrict the tip flow like a higher AR, without the bending load; but add parasite drag .
Tip tanks Act like an end-plate, cut induced drag, and reduce root bending .
Winglets Small aerofoils angled to the tip flow: a small forward force , and they weaken the vortex .
Tip shape Turned-down or turned-up tips also weaken the vortex.
Chapter 8 · Induced Drag
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Since aspect ratio cannot grow for ever, designers attack the tip vortex directly. A flat end-plate at the tip restricts the flow round the tip and has an effect similar to increasing the aspect ratio, but without the extra bending load. The plate itself adds parasite drag, though, so at high speed there may be no saving at all. Tip tanks, fuel tanks mounted on the wingtips, act like end-plates, reducing induced drag, and their weight also reduces the root bending moment. Winglets are the modern solution: small, nearly vertical aerofoils forming part of the wingtip. They partly block the air flowing from the bottom surface to the top, weakening the vortex, and because they are angled to the inflowing tip flow, they generate a small forward force, a kind of negative drag. The small vortex from the winglet also interferes with and weakens the main tip vortex. Finally, simply shaping the tip, turned down or turned up, can weaken the vortex too.
Planform
The spanwise lift distribution An elliptical lift distribution gives uniform downwash and the least induced drag for a given span An elliptical planform gives it, but is costly to build A rectangular wing loads its tips more: more induced drag A tapered wing with washout (twist) and/or spanwise camber variation comes close to elliptical Washout also helps the root to stall first Elliptical uniform downwash: least Di Rectangular more lift near the tips: more Di Tapered + washout close to elliptical coloured line: lift per metre of span
Chapter 8 · Induced Drag
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The last design factor is how the lift is spread along the span. Theory shows that, for a given span and lift, the least induced drag comes from an elliptical lift distribution, which gives the same downwash at every point along the span. An elliptical planform, like the famous Spitfire wing, produces this naturally, but it is expensive to build. A simple rectangular wing carries relatively more lift towards its tips, so it sheds stronger tip vortices and has more induced drag. The practical answer is a tapered wing, combined with washout, which is twisting the wing so the tip meets the air at a smaller angle than the root, and sometimes with a change of camber along the span. With these, the lift distribution comes close to elliptical. Washout has a second benefit: by unloading the tips, it helps the root stall before the tips, which keeps the ailerons working near the stall.
Ground effect 1
Ground effect Within about one wingspan of the ground, the ground restricts the vortices and the downwash Strong below about half the span : at a tenth of the span induced drag is roughly halved Smaller induced angle : lift is tilted back lessAt the same α : more lift and less induced drag Low-wing aircraft feel it more than high-wing ones Out of ground effect In ground effect (height < ½ span) smaller vortices, less downwash → less induced drag
Chapter 8 · Induced Drag
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ground effect happens when a wing flies close to the ground, roughly within one wingspan of it. The ground gets in the way of the airflow pattern. The tip vortices cannot develop fully, and the downwash behind the wing is restricted because the air cannot be pushed down through the ground. The effect is small at one span but grows quickly as the wing gets lower, and it is strong below about half the span; at a height of one tenth of the span, induced drag is roughly halved. With less downwash, the induced angle is smaller, so the lift is tilted back less. The result, at the same angle of attack, is more lift and less induced drag. That is a classic exam question. A low-wing aircraft, whose wing is closer to the runway, feels ground effect more strongly than a high-wing aircraft.
Ground effect 2
What ground effect does to the pilot Phase What happens Why Landing flare The aircraft floats ; it is reluctant to touch down, especially if too fast Less induced drag, so speed bleeds off slowly; more lift at the same α Entering ground effect Tendency to pitch nose-down on many types: more back pressure needed Less downwash at the tailplane changes its angle of attack Take-off run The aircraft may lift off below the recommended speed Extra lift and less drag close to the ground Climbing out of ground effect Induced drag rises , lift falls at the same α; the aircraft may sink back Full downwash returns; a higher α is needed Instruments Airspeed and altimeter position error may change Pressure field round the static vents changes
Never try to climb out of ground effect below the recommended take-off speed: the extra drag can leave you unable to accelerate or climb.
Chapter 8 · Induced Drag
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is what ground effect means in practice. In the landing flare, the drop in induced drag means the speed bleeds away slowly, and with extra lift at the same angle of attack the aircraft tends to float along the runway, especially if it arrives too fast. On many aircraft, the reduced downwash at the tailplane also changes the tail's angle of attack, giving a nose-down pitching tendency, so a little more back pressure is needed in the flare. On take-off, ground effect can let an aircraft become airborne below its recommended speed. The danger comes as it climbs out of ground effect: the full downwash returns, induced drag rises, and at the same angle of attack the lift falls, so the aircraft may sink back towards the runway or be unable to accelerate. Ground effect can also change the pressure round the static vents, so expect small changes in the position error of the airspeed indicator and altimeter.
Summary
Induced drag in one page Cause Pressure difference → spanwise flow (top inboard, bottom outboard) → tip vortices .
Direction From behind: left clockwise , right anticlockwise . Down between, up outside.
Geometry Extra downwash: αe = α − αi ; lift tilts back; rearward part = Di .
Speed Di ∝ 1 / IAS² . Speed × 2: CDi × 1/16, Di × ¼.
Lift Di ∝ L² : weight and load factor. 60° bank → × 4.
Aspect ratio CDi ∝ 1 / AR . AR = span² / area. Limits: bending, roll, clearance.
Design Elliptical loading; taper + washout ; end-plates, tip tanks, winglets .
Ground effect Same α: more lift, less Di . Float on landing; sink leaving it.
Chapter 8 · Induced Drag
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it together. Induced drag is caused by the pressure difference that makes lift: air spills round the tips, flowing inboard on top and outboard underneath, and rolls up into tip vortices. Viewed from behind, the left one turns clockwise and the right one anticlockwise, with downwash between them. The extra downwash reduces the effective angle of attack, tilts the lift backwards, and the rearward component is induced drag. For a given weight, induced drag is proportional to one over the IAS squared: double the speed and the induced drag coefficient falls to one sixteenth while induced drag falls to a quarter. It is proportional to lift squared, so weight and load factor raise it, four times at sixty degrees of bank. Its coefficient is inversely proportional to aspect ratio. Designers aim for an elliptical lift distribution, using taper, washout, and tip devices like winglets. And close to the ground, at the same angle of attack, you get more lift and less induced drag.