Principles of Flight · Chapter 27
Limitations and the Flight Envelope Why an aeroplane has speed and load limits: load factor, the V-n diagram, VA, VC and VD, gusts and rough-air speed, the speeds on your airspeed indicator, and flutter, divergence and aileron reversal.
-1 0 +1 +2 +3 VS VA VC VD n speed (EAS) flight envelope © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the chapter on limitations and the flight envelope. Every aeroplane is built as light as it can be, so its strength is only just enough for the loads it is designed to meet. In this lesson you will learn what load factor means, how the V n diagram shows the safe combinations of speed and g, why the manoeuvring speed falls when you are lighter, how gusts load the structure and how the rough-air speed is chosen, what each limiting speed on your airspeed indicator means, and finally how flutter, divergence and aileron reversal set limits through stiffness rather than strength.
Roadmap
Strength, stiffness and control set the limits Every limit in the flight manual protects one of three things: the strength of the structure (resisting load), its stiffness (resisting deformation), or adequate control .
1 · Loads Limit and ultimate load, the 1.5 factor of safety, and load factor n = lift ÷ weight.
2 · The V-n diagram The CL max boundary, limit load factors, VA , VC , VD and the negative side.
3 · Operating speeds VMO /MMO , VNE , VNO , gear and flap limits, and the ASI markings.
4 · Gusts How a vertical gust raises the load factor; the gust envelope; VB and the rough-air speed.
5 · Aeroelasticity Divergence, wing and control-surface flutter, mass balance.
6 · Aileron reversal Low-speed reversal near the stall and high-speed reversal from wing twist.
Chapter 27 · Limitations and the Flight Envelope
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every limitation in a flight manual protects one of three things. The first is strength, which is the ability of the structure to carry a load without breaking. The second is stiffness, which is its ability to resist being bent or twisted out of shape. The third is adequate control of the aircraft. In this lesson we work through six parts. We start with loads and load factor. Then we build the V n diagram, the manoeuvre envelope, and find the design speeds V A, V C and V D on it. Next come the operating speeds you will find in the flight manual and on the airspeed indicator. Then we look at gusts and the rough-air speed. Finally we turn to stiffness: divergence, flutter and aileron reversal.
Part 1 · Loads
Limit load, ultimate load and the factor of safety Limit load : the maximum load expected in service Ultimate load : the load at which the structure fails Factor of safety = ultimate ÷ limit = 1.5 for aircraft structuresMuch lower than in other engineering, because weight must be kept to a minimum Between limit and ultimate the structure may be permanently deformed So the margin is not for using : never exceed the published limits 0 1 2 2.5 3 3.75 Deformation (bending, twist) Load factor n Limit load max expected in service Ultimate load the structure fails elastic: springs back permanent set possible here Factor of safety = ultimate ÷ limit = 1.5
Chapter 27 · Limitations and the Flight Envelope
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two loads define the strength of an aircraft structure. The limit load is the biggest load the aircraft is expected to meet in service. The ultimate load is the load at which the structure actually fails. The ratio of ultimate load to limit load is the factor of safety, and for aircraft structures it is only one point five. A bridge or a lift cable might use a factor of three or more, but every extra kilogram of structure in an aeroplane costs payload and fuel, so the margin is kept as small as possible. Look at the graph. Up to the limit load the structure behaves elastically and springs back. Beyond it, the metal can take a permanent set, so the wing may be bent for good even though it has not broken. That is why the safety factor is not a reserve for the pilot to use. Stay within the published limits.
Part 1 · Load factor
Load factor: lift divided by weight Load factor n = lift ÷ weight , often called "g"; level flight: n = 1 Lift twice the weight: n = 2 . In a level turn n = 1 ÷ cos φ : 60° bank gives 2 g Limits are given as load factors so the rule applies to every aircraft But the structure fails at a fixed load : 10 000 lb fails a 4 000 lb aircraft at 2.5 g , a 5 000 lb one at 2.0 g It takes less g to overstress a heavy aircraft So limit load factors are based on the maximum weight Lift = 2 W Weight W 60° Level turn n = 1 ÷ cos φ 0° 1.00 g 30° 1.15 g 45° 1.41 g 60° 2.00 g 70° 2.92 g Vertical part of lift = weight, so total lift and n rise with bank. Structure fails at 10 000 lb of lift: 4 000 lb aircraft → 2.5 g · 5 000 lb aircraft → 2.0 g
Chapter 27 · Limitations and the Flight Envelope
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Load factor is simply lift divided by weight, and pilots call it g. In straight and level flight lift equals weight, so the load factor is one. If a manoeuvre makes the lift twice the weight, the load factor is two. In a level turn the lift must tilt with the wings and still hold the aircraft up, so lift equals weight divided by the cosine of the bank angle. As you bank to sixty degrees the lift doubles, and so does the load on the wing. The requirements state limits as load factors so that one rule fits every aircraft. But remember that the structure breaks at a particular load in pounds or newtons. If it fails at ten thousand pounds, a four thousand pound aircraft reaches that at two point five g, while a five thousand pound aircraft reaches it at only two g. A heavy aircraft is overstressed with less g, so limit load factors are set at the maximum weight.
Part 2 · Limit load factors
Limit load factors by category The certification rules set the minimum limit load factors; designers do not build stronger than required, because extra strength costs weight.
Category Positive limit Negative limit Typical use Normal (light aircraft) +2.5 to +3.8 (need not exceed 3.8)−1.0 Normal flying, turns up to about 60° Utility +4.4 −1.76 Limited aerobatics, spins where approved Aerobatic +6.0 −3.0 Full aerobatics Large jet transport +2.5 −1.0 up to VC , then rising linearly to 0 at VD Airline operations Transport, flaps extended +2.0 0 Take-off, approach and landing
Ultimate load factors are 1.5 × these: for example 2.5 × 1.5 = 3.75 g for a transport aircraft.
Chapter 27 · Limitations and the Flight Envelope
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
How much g must an aircraft be designed for? The certification rules set the minimum limit load factors, and because extra strength means extra weight, manufacturers do not build stronger than they must. A normal category light aircraft has a positive limit of at least two point five, which need not be more than three point eight, and a negative limit of minus one. A utility aircraft is designed for plus four point four and minus one point seven six. An aerobatic aircraft is designed for plus six and minus three. A modern jet transport has a positive limit of two point five, and a negative limit of minus one up to the design cruising speed, which tapers linearly to zero at the design dive speed. With flaps extended the transport limit falls to plus two. Multiply any limit by one point five to get the ultimate load factor; for a transport that is three point seven five g.
Part 2 · The manoeuvre envelope
The V-n diagram: load factor against speed -1 0 1 2 3 4 0 50 100 150 200 250 300 350 Speed (knots EAS) Load factor n Ultimate 3.75 g (limit × 1.5) 1 g level flight Stall: CL max line Negative CL max Safe operation O S A C D E F H Example aircraft VS (1 g) 100 kt VA = 100√2.5 158 kt VC 260 kt VD (VC = 0.8 VD ) 325 kt Limit load factors +2.5 / −1.0 Negative stall at −1 g 129 kt n = (V ÷ VS )² on the stall line All speeds are EAS Inside the blue area the aircraft can neither stall nor exceed its limit load. Every curve here is computed for the example aircraft.
Chapter 27 · Limitations and the Flight Envelope
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the manoeuvre envelope, or V n diagram, for an example transport aircraft whose one g stalling speed is one hundred knots. Load factor goes up the side and equivalent airspeed along the bottom. The red curve from O through S to A is the C L max boundary: the most lift the wing can make at each speed. At one hundred knots that is exactly one g, which is point S, the stall in level flight. The curve is a parabola, because lift grows with the square of speed, so at point A, about one hundred and fifty-eight knots, the wing can just reach the limit of two point five g. From A the top boundary runs flat through C, the design cruising speed, to D, the design dive speed. On the negative side, curve O H is the negative stall, and H F E is the negative limit. Inside the envelope the aircraft can neither stall nor exceed its limit load.
Part 2 · The CL max boundary
Below A you stall; above A you can overstress At a fixed angle of attack, lift and so n grow with V² : each line is a parabola The stalling-angle line OA is the most g the wing can give at each speed Below point A the wing stalls before the limit load factor can be reachedAbove point A a hard pull can exceed the limit load factorThis does not make every manoeuvre above A unsafe: just keep within the limit g Between 2.5 and 3.75 g: possible permanent deformation ; above 3.75 g: failure 0 1 2 3 4 0 50 100 150 200 Speed (knots EAS) Load factor n α 3° α 8° stalling α A limit load factor 2.5 ultimate 3.75 permanent deformation structural failure above the stall line: wing stalls first pull hard here and the limit is passed
Chapter 27 · Limitations and the Flight Envelope
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why is the left-hand boundary curved? At any fixed angle of attack the lift coefficient is fixed, so lift, and with it the load factor, grows with the square of the speed. Each blue line in the graph is a parabola for one angle of attack. The red line is the stalling angle, where the lift coefficient is at its maximum, so it marks the greatest load factor the wing can possibly produce at each speed. Below point A, however hard you pull, the wing stalls before it can reach two point five g, so it protects the structure. Above point A the wing is able to produce more than the limit load factor, so an abrupt pull could overstress the aircraft. That does not mean every manoeuvre faster than A is dangerous; it only means the pilot must keep within the limit g. Between two point five and three point seven five g the structure may be permanently deformed, and beyond three point seven five it can fail.
Part 2 · Design manoeuvring speed
VA : full elevator without overstressing VA : the highest speed at which a sudden, full nose-up elevator input will not exceed the limit load factor Assumed to start from steady level flight (point A1); the wing stalls before the structure is overloaded Stall speed rises with √n , so VA = VS1g × √n Example: VS 60 kt, n 2.5: VA = 60 × √2.5 ≈ 95 kt The tailplane also feels a large load in the pitch-up, so VA is not set any higher than A It covers one abrupt input, not rapid reversals or combined full inputs 0 1 2 2.5 3 0 50 100 150 200 Speed (knots EAS) Load factor n A1 (1 g) A full nose-up elevator stall line n = (V ÷ VS )² limit 2.5 g VS 100 VA = VS √n = 100 × √2.5 ≈ 158 kt
Chapter 27 · Limitations and the Flight Envelope
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The design manoeuvring speed, V A, is the highest speed at which a sudden, full nose-up elevator deflection can be made without exceeding the limit load factor. The designer assumes the aircraft starts in steady level flight, at point A one in the graph, and the pilot snaps the stick fully back. The load factor shoots up, but at or below V A the wing reaches its stalling angle before the load reaches the limit, so the stall protects the structure. Because stall speed increases with the square root of load factor, V A equals the one g stall speed times the square root of the limit load factor. For a stall speed of sixty knots and a limit of two point five, that is sixty times one point five eight, about ninety-five knots. The pitch-up also loads the tailplane heavily, which is another reason V A is not set any higher. And it covers one abrupt input, not repeated reversals.
Part 2 · VA and weight
Lighter aircraft, lower VA The stall line OA is drawn for maximum weight Lighter: lower stall speed , so the stall line meets the limit at a lower speed VA ∝ √weight : VA new = VA × √(Wnew ÷ W)2 500 lb → 2 000 lb: 95 × √0.8 = 85 kt ; 20% less weight, about 10% less VA Weight down 15%: √0.85 = 0.922, VA down about 7.5–8% Why: a lighter aircraft reaches the limit g with less lift, so the wing can overstress it at a lower speed 0 1 2 2.5 3 0 20 40 60 80 100 120 Speed (knots EAS) Load factor n 85 kt 95 kt 2 000 lb 2 500 lb limit 2.5 g VA new = VA × √(Wnew ÷ W) 95 × √(2000 ÷ 2500) = 95 × 0.894 = 85 kt
Chapter 27 · Limitations and the Flight Envelope
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a result that surprises many students: V A gets lower when the aircraft gets lighter. The stall line is drawn for the maximum weight. A lighter aircraft stalls at a lower speed, so its stall line is steeper and meets the limit load factor at a lower speed. Since stall speed varies with the square root of weight, so does V A. In the example, V A is ninety-five knots at two thousand five hundred pounds. At two thousand pounds it becomes ninety-five times the square root of zero point eight, which is about eighty-five knots. So a twenty per cent cut in weight gives roughly a ten per cent cut in V A. In the exam a fifteen per cent weight reduction gives the square root of zero point eight five, about zero point nine two, so V A falls by roughly seven and a half to eight per cent. The reason is that the light aircraft reaches its limit g with less lift, so the wing can overstress it at a lower speed.
Part 2 · Design speeds
VC and VD : cruise and dive design speeds VC , design cruising speed: chosen by the designer to assess strength in the cruise VC must be well above VB (at least 43 kt for large aircraft) and not more than 0.8 VD VC need not exceed VH , max level speed at max continuous power (0.9 VH at sea level for light aircraft) VD , design dive speed: the highest speed considered for strengthBased on an upset at VC into a shallow dive, speed building until recovery VDF : a flight-demonstrated dive speed, used if buffet or high-speed effects limit VD VC : cruise upset VD reached recovery Shallow dive: speed builds before the pilot recovers VD VDF VC VMO VB speed
Chapter 27 · Limitations and the Flight Envelope
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two more design speeds complete the top of the envelope. V C, the design cruising speed, is chosen by the designer to check the strength needed in the cruise. It must leave a good margin above V B, the gust design speed, so that turbulence cannot easily push the aircraft from one to the other; for large aircraft that is at least forty-three knots. It must also be no more than zero point eight of V D. V C need not exceed the maximum level speed at maximum continuous power. V D, the design dive speed, is the highest speed considered for strength. It comes from imagining an upset while cruising at V C: the nose drops into a shallow dive and the speed builds until the pilot recovers. If buffet or other high-speed effects make that speed unsuitable, a demonstrated value, V D F, is used instead. Neither V C nor V D appears in the flight manual; the operating limits are set below them.
Part 2 · Negative g
Negative load factors and the negative stall Large negative g is unusual, but some negative g must be allowed for Push the angle of attack negative far enough and the wing stalls inverted Symmetrical section: same stall angle both ways; cambered section: the negative CL max is usually smaller So the negative stall curve OH is flatter than OA Large aircraft: −1 g up to VC , then linearly to 0 at VD Light aircraft: −1.0 normal, −1.76 utility, −3.0 aerobatic -1 -0.5 0 0.5 1 1.5 -20 -10 0 10 20 Angle of attack α (degrees) Lift coefficient CL +CL max 1.5 −CL max −0.9 zero lift at −2° cambered section: negative stall at a smaller |CL | than positive
Chapter 27 · Limitations and the Flight Envelope
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The lower half of the V n diagram deals with negative g. In normal flying you rarely meet large negative load factors, but a push-over or a strong down gust can give some, so the structure must be designed for them. If the angle of attack is made more and more negative, the wing eventually stalls in the negative direction. For a symmetrical section the negative stall comes at the same angle and the same size of lift coefficient as the positive one. For a cambered section, like the one in the graph, the negative maximum lift coefficient is usually smaller, here minus zero point nine against plus one point five. That is why the negative stall curve O H is flatter than O A, and the negative stall at minus one g comes at a higher speed. Large aircraft must withstand minus one g up to V C, falling linearly to zero at V D.
Part 2 · Reading the envelope
The lines of the manoeuvre envelope Line What it shows If you cross it SL Level flight at 1 g Normal reference line OA (through S)Positive CL max: the stall at each load factor The wing stalls ACD Positive limit load factor (+2.5 g for a transport) Possible permanent deformation ; failure beyond 1.5 × limit DE Design dive speed VD Flutter, buffet, control or strength problems OH Negative CL max: the negative stall The wing stalls inverted HFE Negative limit load factor (−1 g to VC , then to 0 at VD ) Possible structural damage
VC and VD are design speeds for strength; they are not in the flight manual. The scheduled operating limits are set from them.
Chapter 27 · Limitations and the Flight Envelope
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us read the envelope line by line. S L is level flight at one g. O A, passing through S, is the positive C L max boundary: try to fly to its left and the wing stalls. A C D is the positive limit load factor; above it you risk permanent deformation, and at one and a half times the limit, failure. D E is the design dive speed, beyond which flutter, buffet, control problems or overstress may appear. O H is the negative stall, and H F E is the negative limit, minus one g up to V C and tapering to zero at V D. Inside all these lines the aircraft is safe to operate. Keep in mind that V C and V D are design speeds used to check the strength of the aircraft. They are not printed in the flight manual. The speeds you do fly to, which we meet next, are set with a margin below them.
Part 3 · Flap limits
Flaps: more lift, so lower limits Flaps, their mechanism and attachments are built for low dynamic pressure only Flaps raise CL max : the wing can produce more g at a given speed So the flaps-down limit load factor is cut from 2.5 to 2.0 (transport) Example: at 120 kt the clean wing stalls at 1.44 g, but with flaps it can reach 2.3 g VFE : max speed with flaps at a given setting (top of the white arc )Flaps in turbulence: stall margin up, but structural margin down more : do not -1 0 1 2 2.5 3 0 50 100 150 200 250 300 Speed (knots EAS) Load factor n clean: 2.5 g 2.0 g at 112 kt VF 160 kt flaps down CL max (×1.6) 120 kt: clean stall at 1.44 g flaps: 2.30 g > flap limit flaps: no negative load factor
Chapter 27 · Limitations and the Flight Envelope
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Flaps are there to shorten take-off and landing, so they, their operating mechanism and their attachment points are designed only for the low dynamic pressures of slow flight. Flaps also raise C L max, and that has a second effect. On the V n diagram the flaps-down stall line is much steeper, so at quite a moderate speed the wing can produce a large load. In the example, at one hundred and twenty knots the clean wing stalls at about one point four four g, but with flaps down it can reach about two point three g. To protect the flaps and the wing, the flaps-down limit load factor is reduced from two point five to two. V F E, the wing flaps extended speed, is the maximum speed for a given flap position, shown by the top of the white arc. Lowering flaps in turbulence does improve the stall margin, but it reduces the structural margin by more, so only use flaps as the flight manual allows.
Part 3 · Landing gear limits
VLO and VLE Gear is retracted soon after take-off to cut drag; it is not designed for use at high IAS VLO , landing gear operating speed: max speed to extend or retract If different: VLO(EXT) and VLO(RET) In transit the doors are open ; they only fair the bay and cannot take high air loads VLE , landing gear extended speed: max speed with gear down and locked With the doors closed again, VLE is normally higher than VLO In transit: VLO doors open in the airflow doors take high air loads Down and locked: VLE doors closed again bay faired over again VLO (operating) < VLE (extended) If extension and retraction differ: VLO(EXT) and VLO(RET)
Chapter 27 · Limitations and the Flight Envelope
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The landing gear has two speed limits. The gear is normally retracted as soon as possible after take-off, to cut drag and improve the climb gradient, so there is no need for its mechanism to work at high indicated airspeeds, and designing it to do so would only add weight. V L O, the landing gear operating speed, is the maximum speed at which you may extend or retract the gear. If extension and retraction have different limits they are written V L O extend and V L O retract. While the gear is moving, the doors are open, and they are only there to streamline the bay, not to take large air loads. V L E, the landing gear extended speed, is the maximum speed with the gear fully down and locked, for example on a ferry flight. By then the doors have closed again, so V L E is normally higher than V L O. That is the reason behind the exam question.
Part 3 · Light aircraft speeds
VNE , VNO and the ASI arcs VNE , never-exceed speed: the maximum airspeed for small aircraft; red radial line VNE = 0.9 VD , leaving room to recover from upsets VNO , maximum structural cruising speed: not more than the lesser of VC or 0.89 VNE Green arc : VS1 to VNO , normal operationsYellow arc : VNO to VNE , smooth air only , with cautionWhite arc : VS0 to VFE , the flap operating range40 60 80 100 120 140 160 180 200 KNOTS VS0 48 VFE 85 VNO 129 VNE 163 VS1 55
Chapter 27 · Limitations and the Flight Envelope
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a light aircraft, the limits you fly to are painted on the airspeed indicator. V N E, the never-exceed speed, is the maximum airspeed at which the aircraft may be flown, shown by a red radial line. It is set at zero point nine of the design dive speed, to leave room to recover from an upset. V N O, the maximum structural cruising speed, is the normal cruise limit; it must not be more than the lesser of V C and zero point eight nine of V N E. It is the top of the green arc, which runs from the flaps-up stall speed, V S one. From V N O to V N E is the yellow arc, the caution range, which you may use only in smooth air, and then with care. The white arc runs from the landing-configuration stall speed, V S zero, up to V F E. For this example aircraft V N E is one hundred and sixty-three knots, and V N O one hundred and twenty-nine.
Part 3 · Large aircraft
VMO /MMO and the crossover altitude Large aircraft (over 5 700 kg MTOM): VMO /MMO , the maximum operating limit, not to be deliberately exceeded in any phase VMO ≤ VC and far enough below VD that VD is highly improbable to be reached At constant IAS, Mach number rises with altitude , so MMO takes over at about 24 000 to 29 000 ft Climbing at constant IAS you can exceed MMO Descending at constant Mach you can exceed VMO Two independent overspeed warnings (clacker), silenced only by slowing below VMO /MMO 0 10 20 30 40 350 400 450 500 550 600 True airspeed (knots) Pressure altitude (1000 ft) crossover ≈ 26000 ft VMO 340 kt (constant IAS) MMO 0.82 permitted
Chapter 27 · Limitations and the Flight Envelope
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Large aircraft, those over five thousand seven hundred kilograms maximum take-off mass, have a maximum operating limit speed instead of a never-exceed speed. V M O is an indicated airspeed that must not be deliberately exceeded in any phase of flight. It must be no greater than V C, and far enough below V D that reaching V D by accident is highly improbable. But as you climb at a constant indicated airspeed, the true airspeed rises and the speed of sound falls, so the Mach number increases. Compressibility then becomes the limit, and V M O hands over to M M O. In the graph, for three hundred and forty knots and Mach zero point eight two, the crossover is near twenty-six thousand feet. So a climb at constant IAS can take you past M M O, and a descent at constant Mach can take you past V M O. Two independent warning systems sound a clacker, which stops only when you slow down.
Part 4 · Gust loads
A vertical gust raises the angle of attack A vertical gust tilts the relative airflow : tan Δα = gust speed ÷ TAS CL jumps, but IAS has no time to change, so lift and n jump Example: CL 0.42 in level flight, 0.1 per degree, gust adds 3° New CL = 0.42 + 0.3 = 0.72, so n = 0.72 ÷ 0.42 ≈ 1.7 For a given aircraft, the increment depends only on airspeed and gust speed Design gusts and speeds are in EAS ; the angle change itself depends on TAS aircraft TAS, V gust U effective airflow Δα more lift tan Δα = U ÷ V Level: CL 0.42, n = 1. Gust adds 3° × 0.1 = 0.30 New CL = 0.72, so n = 0.72 ÷ 0.42 = 1.7 Lift rises in step with CL : IAS has no time to change
Chapter 27 · Limitations and the Flight Envelope
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
How does a gust load the structure? A vertical gust adds an upward component to the air meeting the wing, so the relative airflow tilts and the angle of attack increases. The tangent of the change equals the gust speed divided by the true airspeed. The lift coefficient jumps, but the aircraft has no time to slow down, so the lift and the load factor jump too. Here is a worked example. An aircraft in level flight has a lift coefficient of zero point four two, and each degree of angle of attack adds zero point one. A gust adds three degrees, so the lift coefficient rises by zero point three to zero point seven two. The load factor becomes zero point seven two divided by zero point four two, about one point seven g. For a given aircraft, only the airspeed and the gust speed change the answer. Design gusts are stated in equivalent airspeed, but the angle change itself depends on true airspeed.
Part 4 · Gust sensitivity
What makes an aircraft feel gusts more? A steeper lift curve means a bigger CL jump for the same Δα, so more g High aspect ratio, straight wings have steep lift curves: more gust responseLow aspect ratio or swept wings have flatter lift curves: smaller Δn High wing loading reduces Δn : the same extra lift is a smaller fraction of the weightHigher speed and stronger gusts both raise Δn in proportion So a heavy aircraft rides gusts more smoothly but meets its failing load at lower g 0 0.4 0.8 1.2 0 2 4 6 8 10 12 14 Angle of attack (degrees) CL high aspect ratio low AR or swept +0.27 +0.18 3° gust Δn = ρ0 · U · V · a ÷ (2 · W/S) U gust (EAS) · V aircraft EAS · a lift-curve slope W/S wing loading: higher wing loading → smaller Δn sharp-edged gust, before any alleviation
Chapter 27 · Limitations and the Flight Envelope
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why do some aircraft ride turbulence more smoothly than others? For a given gust and speed, the extra load depends on how much the lift coefficient changes for each degree of angle of attack, which is the slope of the lift curve. A high aspect ratio, straight wing has a steep lift curve, so the same three degree gust adds more lift and more g. A low aspect ratio or swept wing has a flatter lift curve and gives a smaller increase. In the graph the same gust adds zero point two seven to one wing and only zero point one eight to the other. Wing loading matters too. A heavily loaded wing makes the same extra lift, but it is a smaller fraction of the aircraft weight, so the increase in g is smaller. The formula at the bottom collects all of this: the increment grows with gust speed, airspeed and lift-curve slope, and falls as wing loading rises.
Part 4 · The gust envelope
Design gusts: 66, 50 and 25 ft/s at VB , VC and VD -1 0 1 2 3 0 50 100 150 200 250 300 350 Speed (knots EAS) Load factor n manoeuvre limit 2.5 g stall line 66 ft/s 50 ft/s 25 ft/s −66 ft/s −50 ft/s −25 ft/s VB VC VD Design gusts (EAS) VB 138 kt 66 ft/s n 1.91 VC 260 kt 50 ft/s n 2.30 VD 325 kt 25 ft/s n 1.81 Gust lines: n = 1 ± k·U·V At VB a 66 ft/s gust stalls the wing at n 1.9, before 2.5 g k = 0.0001 per ft/s per kt for this example aircraft Gust strengths set in the 1940s from flight recorder data, and still confirmed by modern recorders. VB , VC and VD are design speeds, not flight-manual speeds.
Chapter 27 · Limitations and the Flight Envelope
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The structure must survive defined vertical gusts as well as manoeuvres. Each straight gust line starts at one g and fans out with speed, because the load factor increment grows with airspeed. The aircraft must withstand a sixty-six feet per second gust at V B, the design speed for maximum gust intensity; fifty feet per second at V C, because turbulence may be met before the pilot can slow down from the cruise; and twenty-five feet per second at V D, for the remote chance of a gust during an upset. Joining the ends of the lines gives the gust envelope, shown in green. Notice point V B. It is where the sixty-six feet per second line meets the stall line, so if that gust arrives at V B the wing stalls at about one point nine g, before the limit load is reached. In this example the gust envelope stays inside the two point five g manoeuvre limit.
Part 4 · Rough-air speed
VRA /MRA : between the stall and overstress 0 5 10 15 20 100 150 200 250 300 350 400 True airspeed (knots) Added α (degrees) 15.6° 11.1° 7.4° 66 ft/s vertical gust Δα = arctan(U ÷ V) Choosing the rough-air speed (example aircraft) 1 g stall 100 stall in 66 ft/s gust 138 VRA ≈ 183 limit load in 66 ft/s gust 227 VC 260 VD 325 stall risk overstress Too slow: the gust stalls the wing. Too fast: it overstresses the structure. VRA /MRA sits between: equal protection against both. At low weight the gust stall line moves slower and the strength line faster, so one VRA serves all weights; the maximum altitude for a 1.5 g buffet margin does fall with weight.
Chapter 27 · Limitations and the Flight Envelope
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
How fast should you fly in turbulence? The left graph shows the problem at the slow end. A sixty-six feet per second gust adds more than fifteen degrees of angle of attack at one hundred and forty knots true, but only about seven degrees at three hundred knots. So if you are slow, a gust can stall the wing. At the fast end, as we saw, a gust can overstress the structure. On the right, for the example aircraft, the stall in a sixty-six feet per second gust comes at about one hundred and thirty-eight knots, and the limit load is reached at about two hundred and twenty-seven knots. The rough-air speed, V R A, or the rough-air Mach number at height, is chosen between them, giving equal protection against both. V B alone would give the best strength protection, but it is slow, so a slightly higher V R A is used. Weight effects cancel out, so one rough-air speed is normally quoted.
Part 5 · Aeroelasticity
Divergence: the wing that winds itself up Aeroelasticity : air loads distort the structure, the distortion changes the air loads, and so onAerodynamic force grows with V² (dynamic pressure), but torsional stiffness is constant Divergence : lift at the AC, ahead of the flexural axis , twists the wing nose up, adding more lift, until it breaksDepends on flexibility , the AC to flexural axis distance and dynamic pressure (IAS) Divergence speed must be above VD /MD Cures: stiffer structure (heavier) or move the flexural axis forward , e.g. engines ahead of the wing 1 2 3 4 lift at AC flexural axis AC ahead of flexural axis Speed VD divergence aero twist ∝ V² torsional stiffness
Chapter 27 · Limitations and the Flight Envelope
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
No aircraft is perfectly rigid. Air loads bend and twist the structure, the distortion changes the air loads, and this interplay is called aeroelasticity. At low speed the effect is negligible, but aerodynamic force grows with the square of speed while the torsional stiffness of the structure stays the same, so at some high speed the air can win. Look at the wing tip seen end-on. A gust raises the lift. That lift acts at the aerodynamic centre, which is ahead of the flexural axis, so as well as bending the tip up it twists it nose up. More angle of attack means more lift, more twist, and the tip winds up through positions two, three and four like a spring, until it breaks. That is divergence. How bad it is depends on flexibility, on the distance between the aerodynamic centre and the flexural axis, and on dynamic pressure. Designers keep divergence above V D, either by stiffening the wing or by moving the flexural axis forward.
Part 5 · Flutter
Flutter: an oscillation that feeds itself Flutter : a rapid, uncontrolled, growing oscillation of a surface; usually catastrophic Involves aerodynamic forces, inertia forces and the elastic properties of the structure Mass and stiffness set natural frequencies ; air forces near them can drive a resonance Must not occur in the flight envelope: kept beyond VD /MD Backlash (free play) or poor maintenance can lower the flutter speed below VMO Podded engines ahead of the wing act as mass balance: flexural axis forward, flutter delayedengine pod well ahead of the leading edge flight aerodynamic centre line flexural axis, moved forward flexural axis without the engine below flutter speed above flutter speed damped: dies away each cycle bigger
Chapter 27 · Limitations and the Flight Envelope
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Flutter is a rapid, uncontrolled oscillation of part of the structure which grows with each cycle, and it normally ends in catastrophic failure. It involves three things together: aerodynamic forces, inertia forces and the elasticity of the structure. The way mass and stiffness are spread through a wing gives it natural frequencies of vibration. If the air forces happen to drive the structure near one of those frequencies, the oscillation is not damped but fed, as in the right-hand trace. Flutter must never occur inside the flight envelope, so designers push it beyond V D. Any change of mass or stiffness changes the flutter speed, and if maintenance is poor and there is excessive free play, called backlash, flutter can appear well below V M O. On jet transports the engines hang on pylons ahead of the leading edge. Their mass moves the flexural axis forward, closer to the aerodynamic centre, which raises the flutter speed without making the wing heavier.
Part 5 · Control surface flutter
Torsional aileron flutter and mass balance 1 Aileron down: upward force on the hinge 2 Wing twists, trailing edge up; aileron lags behind 3 Wing stops; aileron flicks up, loads TE down 4 Wing twists back: the cycle repeats The cure mass ahead of the hinge puts the aileron CG on (or just ahead of) the hinge or: irreversible powered controls ● wing torsional axis aileron CG behind its hinge: inertia makes it lag Flexural aileron flutter is the same idea with the wing bending tip-up and tip-down; mass balance near the tip needs least weight. If flutter starts, reduce speed at once: close the throttles but avoid rapid changes of attitude or configuration. Elevators, rudders and even tabs are mass balanced too.
Chapter 27 · Limitations and the Flight Envelope
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Control surfaces can flutter too, when their oscillation couples with the bending or twisting of the wing, tailplane or fin. It can be started by free play in the control circuit or by a gust, and it develops if the centre of gravity of the control surface is behind its hinge. Follow the four frames. One: the aileron goes down and pushes the hinge up. Two: the wing twists, trailing edge rising, but the aileron, with its weight behind the hinge, lags and is left further down. Three: the stiffness of the wing stops the twist, and the aileron flicks up, loading the trailing edge downwards. Four: the wing twists the other way and the cycle repeats, bigger each time. The cure is mass balance: a weight ahead of the hinge to bring the centre of gravity onto, or slightly ahead of, the hinge line. Fully powered, irreversible controls also prevent it. If flutter does start, reduce speed at once, but avoid rapid changes of attitude or configuration.
Part 6 · Aileron reversal
Low-speed aileron reversal At high angles of attack , near the stall, lowering an aileron raises that wing's effective angle of attack The extra camber can push the outer wing past the critical angle That wing stalls and drops instead of rising: the roll is reversed Example: wing at 15°, aileron down: effective angle about 22° , beyond the stall Prevented by washout , slots and differential or Frise ailerons; near the stall use rudder with care Not to be confused with high-speed reversal, which is a stiffness problem relative airflow 15° chord ≈ 22° effective flow separates Near the stall, the down-going aileron pushes its wing past the critical angle. That wing stalls and drops: roll reverses. Cure: avoid large aileron near the stall; use rudder.
Chapter 27 · Limitations and the Flight Envelope
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aileron reversal means that moving the ailerons rolls the aircraft the wrong way, and it can happen at both ends of the speed range. At low speed the wing is already at a high angle of attack. Lowering an aileron to raise a wing increases the camber, and with it the effective angle of attack of that part of the wing. If the wing was already close to the stall, say at fifteen degrees, the lowered aileron can take the outer section to an effective twenty-two degrees or so, beyond the critical angle. That section stalls, loses lift, and the wing drops instead of rising. Designers fight this with washout, slots, and differential or Frise ailerons, and near the stall the pilot should be careful with large aileron inputs and use the rudder to help. Keep this separate in your mind from high-speed reversal, which we look at next and which is caused by the wing twisting.
Part 6 · Aileron reversal
High-speed aileron reversal and its cure Lowering an aileron puts an upward force behind the flexural axis This twists the wing nose down , reducing its angle of attack and its lift At high dynamic pressure the lift lost by twist exceeds the lift gained: the wing drops Reversal speed must be above VD /MD Inboard ailerons on the stiff inner wing work at all speeds; outboard ailerons are locked out at high speed (when flaps retract)Roll spoilers , further forward on stiffer structure, twist the wing far lessflexural axis aileron lift nose-down twist grey: before pink: aileron down inboard aileron: all speeds outboard: low speed only roll spoilers: forward, on stiffer structure
Chapter 27 · Limitations and the Flight Envelope
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
High-speed aileron reversal is a stiffness problem. When an aileron goes down, the air pushes up on it, and because the aileron is behind the flexural axis of the wing, that force twists the wing nose down. The twist reduces the angle of attack of the whole outer wing and therefore its lift. At low speed the twist is tiny and the aileron wins. But the twisting moment grows with dynamic pressure, so at high speed the lift lost through twist can exceed the lift gained from the extra camber, and the wing drops instead of rising. Designers keep the reversal speed above V D. Jet transports do it with two pairs of ailerons. The inboard ailerons sit on the stiff inner wing and work at all speeds; the outboard ailerons are locked out at high speed, normally when the flaps are retracted. Roll control spoilers help too: they are further forward, on stiffer structure, so they twist the wing much less.
Summary
What to take into the exam Loads Limit = max in service; ultimate = failure; factor of safety 1.5. n = L ÷ W. Heavy aircraft overstress at lower g.
Categories Normal +2.5 (to 3.8)/−1; utility +4.4/−1.76; aerobatic +6/−3; transport +2.5/−1; flaps +2.0.
V-n diagram OA: CL max, n = (V ÷ VS )². Below A you stall first; above A you can overstress. OH negative stall.
VA Full abrupt nose-up without exceeding limit g. VA = VS √n; VA ∝ √W: lighter, lower VA .
Speeds VC ≤ 0.8 VD ; VNE = 0.9 VD ; VNO ≤ VC or 0.89 VNE ; VLO < VLE ; VFE top of white arc.
VMO /MMO Crossover 24 000–29 000 ft. Climb at constant IAS: exceed MMO . Descend at constant Mach: exceed VMO .
Gusts 66/50/25 ft/s at VB /VC /VD . Δn up with slope, speed, gust; down with wing loading. VRA between stall and overstress.
Aeroelastic Divergence and reversal: AC vs flexural axis, ∝ IAS. Flutter: mass balance, no backlash. Reduce speed, gently.
Chapter 27 · Limitations and the Flight Envelope
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it together. Limit load is the most expected in service, ultimate load is failure, and the factor of safety is one point five. Load factor is lift over weight, and a heavy aircraft is overstressed at a lower g. Remember the category limits. On the V n diagram, the C L max line rises with the square of speed: below point A the wing stalls first, above A you can overstress. V A equals the stall speed times the square root of the limit load factor, and it falls with weight. V C is no more than zero point eight of V D, V N E is zero point nine of V D, and V L O is lower than V L E. Climbing at constant IAS can exceed M M O, and descending at constant Mach can exceed V M O. Design gusts are sixty-six, fifty and twenty-five feet per second, and the rough-air speed sits between stall and overstress. Finally, divergence, reversal and flutter are stiffness limits, kept beyond V D.