Principles of Flight · Chapter 29
Propeller Principles How a propeller turns engine power into thrust: blade angle, pitch and slip, the angle of attack set by RPM and TAS, blade forces and twisting moments, efficiency, and the constant speed unit.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to propellers. Almost every light aircraft you will fly, and many airliners, pull themselves through the air with a propeller, and the exam expects you to understand it as a rotating wing. In this lesson we define blade angle, pitch, slip and the helix angle, see why the angle of attack of a blade depends on both R P M and true airspeed, look at the forces and twisting moments on a blade, and finish with efficiency and the constant speed propeller.
Roadmap
A propeller is a rotating wing Everything in this lesson follows from one idea: each blade section is an aerofoil moving along a helix .
1 · Definitions Plane of rotation, blade angle , twist, geometric and effective pitch , slip, helix angle.
2 · Angle of attack How TAS and RPM set it, and why a fixed pitch propeller suits only one speed.
3 · Forces Total reaction split into thrust and propeller torque ; blade bending; CTM and ATM .
4 · Efficiency and CSU Thrust power ÷ shaft power; variable pitch, the prop lever and the constant speed unit .
Chapter 29 · Propeller Principles
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for this lesson. The whole subject rests on one idea: a propeller blade is a wing that happens to be spinning, so each section of it meets the air at an angle of attack and makes lift and drag, just like the wing of the aeroplane. First we pin down the definitions: plane of rotation, blade angle, twist, geometric and effective pitch, slip and the helix angle. Then we find out what sets the blade angle of attack, which turns out to be the R P M and the true airspeed together, and why that is a real problem for a fixed pitch propeller. Third, we resolve the blade force into thrust and propeller torque and meet the two twisting moments, C T M and A T M. Finally we define efficiency and see how the constant speed unit keeps a propeller efficient over a wide speed range.
What a propeller does
Thrust by throwing air backwards A propeller turns shaft power from the engine into thrust It accelerates a mass of air rearwards ; the equal and opposite reaction drives the aircraft forwards Thrust = mass flow × velocity increase : e.g. 150 kg/s × 20 m/s = 3 000 NEach blade is an aerofoil : chord, camber, thickness/chord and aspect ratio mean what they do for a wing A large, slowly accelerated mass of air is more efficient than a small, fast jet THRUST slow air in faster air out propeller disc stream tube narrows as the air speeds up
Chapter 29 · Propeller Principles
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A propeller has one job: to turn the shaft power of the engine into thrust. It does that by grabbing a mass of air and accelerating it rearwards. Newton tells us that a force is needed to accelerate that air, and the equal and opposite reaction pushes the propeller, and the aircraft, forwards. So thrust equals the mass of air handled each second times the increase in its speed. For example, one hundred and fifty kilograms a second speeded up by twenty metres per second gives three thousand newtons of thrust. Each blade does this the same way a wing makes lift: it is an aerofoil, with a chord, camber, thickness and aspect ratio. As a rule, moving a big mass of air gently is more efficient than moving a small mass violently, which is why propellers are large compared with jet nozzles.
Definitions
Parts of the blade Root (shank) at the hub, tip at the outer end; the blade turns about its pitch change axis The back is the cambered face, facing forward; the thrust face is the flatter rear face The plane of rotation is the plane in which the blades turn, at right angles to the propeller shaft Sections nearer the tip travel further each revolution, so they move faster Because the angle changes along the blade, it is quoted at a reference station, 75% of the radius tip root (shank) 75% radius: reference station hub pitch change axis 50° 28° 17° sections: blade angle falls towards the tip
Chapter 29 · Propeller Principles
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before we go further, let us name the parts of a blade. The root, or shank, is the thick inner end held in the hub, and the tip is the outer end. A variable pitch blade turns in the hub about its long axis, which we call the pitch change axis. The blade is an aerofoil, so it has a cambered face and a flatter face. The cambered face points forward and is called the back; the flatter rear face, which carries the higher pressure when the propeller is pulling, is called the thrust face or pressure face. The plane of rotation is the flat plane in which the blades turn, at right angles to the shaft. Look at the sections on the right: the blade angle falls steadily from root to tip. Because it changes, we always quote it at a reference station, seventy five per cent of the way out along the radius.
Definitions
Blade angle, fine and coarse Blade angle (pitch): the angle between the chord line and the plane of rotation Measured at the 75% radius station A small blade angle is fine pitch ; a large blade angle is coarse pitch Blade angle is fixed by the hardware; angle of attack depends on how the blade moves through the air Do not confuse blade angle with angle of attack: that is the classic exam trap plane of rotation β direction of flight Blade angle β chord line to plane of rotation, at 75% radius chord line small β = fine pitch large β = coarse pitch
Chapter 29 · Propeller Principles
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The blade angle, also called the pitch, is the angle between the chord line of a blade section and the plane of rotation. Because it varies along the blade, it is measured at the seventy five per cent station. In the model, watch the blades and the section beside them together. When the blade angle is large, we call it coarse pitch: the blade bites a big step forward each turn, like a high gear. When the blade angle is small, we call it fine pitch: a small step each turn, like a low gear. Here is the exam trap. The blade angle is a geometric fact about how the blade sits in the hub. The angle of attack is something else: it is the angle between the chord and the relative airflow, and it depends on how the blade is moving through the air. With the aircraft stationary the two happen to be equal, but in flight they are not.
Definitions
Why the blade is twisted Section speed rises with radius: at 2 400 RPM a 1.8 m propeller moves about 45 m/s at 20% R but 226 m/s at the tip Every section moves forward the same distance per turn, so the outer sections meet the air at a flatter angle The blade angle is therefore reduced from root to tip : this is blade twist Twist gives a nearly constant geometric pitch and a fairly constant angle of attack along the blade in the cruise Without twist the tip would be at too high an angle and the root at too low (or negative) 0 10 20 30 40 50 60 70 20% 40% 60% 80% 100% section speed (rises with radius) 22° at 75% R 54° near the root 15° at the tip blade angle (°) for one constant geometric pitch distance from the hub (per cent of radius)
Chapter 29 · Propeller Principles
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why are propeller blades twisted? Because different parts of the blade move at very different speeds. A section near the hub travels round a small circle; the tip travels round a big one in the same time. At two thousand four hundred R P M, a propeller one point eight metres across moves at about forty five metres per second near the root but about two hundred and twenty six metres per second at the tip. Yet every section moves forward through the air by the same distance each revolution. So the outer sections meet the air at a flatter angle, and to give each section a sensible angle of attack the blade angle must fall towards the tip. The graph shows the result for a constant geometric pitch: about fifty four degrees near the root, twenty two at the seventy five per cent station, and fifteen at the tip. Twist keeps the angle of attack fairly constant along the blade in the cruise.
Definitions
Geometric pitch, effective pitch and slip one revolution: circumference at 75% radius = 2π × 0.675 m = 4.24 m β 22° helix angle 16.9° geometric pitch 4.24 × tan 22° = 1.71 m effective pitch 1.29 m slip 0.43 m The circle swept by the 75% station, unrolled: distance round it along, distance forward up path at the blade angle (no slip) actual path: helix angle Geometric pitch : forward distance per revolution if the blade moved along its blade angle. Effective pitch (advance per revolution) = TAS ÷ revs per second. Slip = geometric − effective.
Chapter 29 · Propeller Principles
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now three linked definitions, using real numbers. Imagine unrolling the circle swept by the seventy five per cent station into a straight line. For a propeller one point eight metres across, that circumference is four point two four metres. If the blade moved through the air like a screw in wood, along its blade angle of twenty two degrees, one turn would carry it forward one point seven one metres. That is the geometric pitch. In flight, the propeller really advances by the true airspeed divided by the revolutions per second. At one hundred knots, about fifty one metres per second, and forty revolutions per second, that is one point two nine metres. This is the effective pitch, or advance per revolution. The shortfall, about point four three metres, is called slip. The actual path makes the helix angle with the plane of rotation, here about seventeen degrees. Do not push the screw idea further: the slip is what gives the blade its angle of attack.
Definitions
The helix angle and the blade path Each blade section moves along a helix : rotation plus forward motion Helix angle : the angle between the actual path and the plane of rotation tan (helix angle) = forward speed ÷ rotational speed of the section More TAS or fewer RPM → a steeper helix (larger helix angle) The air meeting the blade also includes the induced flow drawn in by the propeller itself plane of rotation β relative airflow α direction of flight rotation (RPM) TAS path α = β − helix angle
Chapter 29 · Propeller Principles
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Put rotation and forward motion together and every point on the blade traces out a helix, like the thread of a corkscrew. In the model the yellow line is the path of a blade tip as the aircraft flies to the left. The helix angle is the angle between that actual path and the plane of rotation. Its tangent is simply the forward speed divided by the rotational speed of the section. So the helix angle grows if the true airspeed goes up, and it also grows if the R P M comes down, because the blade then moves sideways more slowly for the same forward progress. One refinement: the air arriving at the blade is not only the true airspeed. The propeller sucks air into the disc, so an induced flow adds to the forward speed. The exam diagrams label this as T A S plus induced flow.
Angle of attack
Blade angle minus helix angle The relative airflow comes along the blade path, opposite to its motion Angle of attack α : between the chord line and the relative airflowα = blade angle β − helix angle α is the result of RPM (rotational velocity) and TAS (forward velocity) together Example at 75% R: β 22°, 2 400 RPM, 100 kt → helix 16.9°, α ≈ 5° plane of rotation β relative airflow α direction of flight rotation (RPM) TAS path α = β − helix angle
Chapter 29 · Propeller Principles
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the most important diagram in the whole topic, so take it slowly. On the right is the velocity triangle. The blade section moves round with its rotational velocity, shown in orange, set by the R P M. At the same time the aircraft carries it forward at the true airspeed, shown in blue. The sum is the path the section really follows. The relative airflow meets the blade along that path, from the opposite direction. The angle of attack is the angle between the chord line and that relative airflow. Look at the angles from the plane of rotation: the chord is at the blade angle, the airflow arrives at the helix angle, and the angle of attack is the difference. With our numbers, a blade angle of twenty two degrees and a helix angle of about seventeen degrees leaves an angle of attack of about five degrees. Change either the R P M or the airspeed and the angle of attack changes.
Fixed pitch problem 1
More TAS, less angle of attack Fixed pitch , constant RPM: as TAS increases the helix angle grows and α decreases Less α means less thrust and less propeller torque At 2 400 RPM, β 22°: α ≈ 22° at rest, 12° at 60 kt, 5° at 100 kt, −1° at 140 kt At some high speed α reaches the zero-lift angle : no thrust at all Beyond that the airflow drives the propeller (windmilling) β α low TAS α ≈ 18° β α high TAS α ≈ −2° flight
Chapter 29 · Propeller Principles
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the first problem with a fixed pitch propeller. The blade angle cannot change, and suppose the R P M stays the same. At the start of the take-off run the true airspeed is low, so the helix is flat and the angle of attack is large. Now watch as the aircraft accelerates. The forward speed arrow grows, the blade path steepens, and the relative airflow swings round towards the chord, so the angle of attack falls. With a blade angle of twenty two degrees at two thousand four hundred R P M, the angle of attack is about twenty two degrees at rest, twelve at sixty knots, five at a hundred knots, and slightly negative by one hundred and forty knots. Go faster still and the angle of attack passes the zero lift angle. The propeller then gives no thrust at all, and beyond that the airflow starts to drive it round.
Fixed pitch problem 2
More RPM, more angle of attack Fixed pitch, constant TAS : as RPM increases the rotational velocity grows, the helix flattens and α increases At 100 kt, β 22°: 2 400 RPM gives α ≈ 5°; 2 700 RPM gives α ≈ 7° Less RPM at the same TAS → smaller, even negative α So the angle of attack of a fixed pitch propeller depends on both forward speed and RPM It works at its best α at only one combination of airspeed and RPM β α low RPM α ≈ −2° β α high RPM α ≈ 12° flight
Chapter 29 · Propeller Principles
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now hold the true airspeed constant and change the R P M instead. At low R P M the blade moves round slowly, so for the same forward speed its path is steep and the angle of attack is small, perhaps even negative. Now increase the R P M. The rotational arrow grows, the blade path flattens, and the angle of attack rises. Increase it further and the angle of attack rises further still. With our example, at one hundred knots, two thousand four hundred R P M gives about five degrees, and two thousand seven hundred gives about seven. Put this slide and the last one together and you have the exam answer: the angle of attack of a fixed pitch propeller depends on both forward speed and engine R P M. A fixed pitch propeller can only be at its best angle of attack at one particular combination of airspeed and R P M.
Fixed pitch in practice
One blade angle, many flight conditions Same fixed propeller (β 22° at 75% R) at about 2 400 RPM:
Condition TAS Helix angle Blade α What happens Full power against the brakes 0 0° ≈ 22° Large thrust but no useful work ; inner sections may stall Early take-off roll 60 kt 10.3° ≈ 12° High thrust, efficiency rising Design point (cruise) 100 kt 16.9° ≈ 5° Best α: maximum efficiency Fast cruise or descent 140 kt 23.0° ≈ −1° Near zero thrust ; RPM tends to run away Steep dive 160 kt 25.9° ≈ −4° Airflow drives the propeller: overspeed risk
Fine-pitch fixed propellers suit take-off and climb (they reach full RPM early); coarse-pitch ones suit cruise but give poor take-off performance.
Chapter 29 · Propeller Principles
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Follow one fixed propeller through a flight at about two thousand four hundred R P M. Run the engine up against the brakes and the helix angle is zero, so the angle of attack equals the blade angle, twenty two degrees. Thrust is large, but the aircraft is not moving, so no useful work is done, and the inner sections may even be stalled. At sixty knots the angle of attack has fallen to about twelve degrees. At about a hundred knots it is about five degrees, the best value: this is the design point and the efficiency is at its maximum. At one hundred and forty knots the angle of attack is about zero, so there is almost no thrust and the R P M tends to run away. In a steep dive the angle of attack is negative and the airflow drives the propeller, with a real risk of overspeeding the engine. So the designer must choose: fine pitch for take-off, or coarse pitch for cruise.
Aerodynamic forces
Thrust and propeller torque The blade section makes a pressure difference; the higher pressure acts on the thrust (pressure) face , the rear face The resulting total reaction is resolved relative to the plane of rotation Thrust : the component at right angles to the plane of rotation , pointing forwardPropeller torque : the component in the plane of rotation , opposing rotationThe engine must supply a torque equal to propeller torque to keep the RPM constant α direction of flight total reaction THRUST propeller torque (resists rotation) blade motion cambered back (front face) flat thrust face (rear)
Chapter 29 · Propeller Principles
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
A blade section at a positive angle of attack makes a pressure difference, exactly like a wing. The higher pressure is on the rear, flatter face, which is why it is called the thrust face or pressure face. The resulting aerodynamic force is the total reaction. For a wing we split it into lift and drag, relative to the airflow. For a propeller it is far more useful to split it relative to the plane of rotation. The component at right angles to the plane of rotation, pointing forward along the shaft, is the thrust. The component in the plane of rotation acts against the direction the blade is moving, and that is the propeller torque. It is the resistance to rotation that the engine has to overcome. When engine torque and propeller torque are equal, the R P M stays steady.
Aerodynamic forces
How thrust and torque load the blade Thrust is small near the root , where rotational speed is low It peaks well outboard and falls to zero at the tip , where the pressures equalise Thrust gives a bending moment that bends the tips forward Propeller torque bends the blades in the plane of rotation, against the direction of rotation Centrifugal force puts each blade in large tension and also tries to twist it (next page) peak near 75–85% R root: slow tip: pressures equalise Thrust along one blade Blade loads (side view) thrust bends the tip forward centrifugal tension flight torque bends the blade back in the plane of rotation (into the page)
Chapter 29 · Propeller Principles
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Thrust is not spread evenly along a blade. Near the root the section moves slowly, so it makes little force; besides, the root is thick and round to carry the loads. Moving outward the section speed rises and so does the thrust, which peaks well out along the blade, around seventy five to eighty five per cent of the radius. At the very tip, high pressure behind and low pressure in front leak round the tip and equalise, so the thrust falls to zero, just as lift falls to zero at a wing tip. These forces bend the blade. Thrust bends the tips forward, because the air is being thrown backwards. Propeller torque bends the blade within the plane of rotation, backwards against the direction it is turning. On top of all that, centrifugal force pulls each blade outwards with a load of many tonnes.
Twisting moments 1
Centrifugal twisting moment: towards fine Centrifugal force acts on every particle of the blade, outward from the hub For particles ahead of and behind the pitch change axis (A and B) it has a component towards the plane of rotation These components make a moment about the pitch change axis: the CTM CTM tends to turn the blade to fine pitch (smaller blade angle) It is the dominant twisting moment in normal operation plane of rotation pitch change axis A B CTM towards FINE Looking along the blade from the tip components of centrifugal force pull A and B into the plane of rotation
Chapter 29 · Propeller Principles
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
A spinning blade also tries to twist about its own pitch change axis, and there are two causes. The first is centrifugal. Every particle of the blade is flung outward, away from the hub. Look along the blade from the tip and pick a particle ahead of the pitch change axis, marked A, and one behind it, marked B. Because the blade is set at an angle, part of the centrifugal pull on each of them is directed towards the plane of rotation. Those two components act on opposite sides of the axis and make a couple, which tries to rotate the blade so that it lies flat in the plane of rotation. In other words, it turns the blade towards fine pitch. This is the centrifugal twisting moment, C T M. It is the bigger of the two twisting moments, and pitch change mechanisms are designed around it.
Twisting moments 2
Aerodynamic twisting moment: towards coarse The blade’s centre of pressure lies ahead of the pitch change axis The total reaction acting there makes a moment towards coarse pitch : the ATM In normal running the ATM partly offsets the CTM, but the CTM is dominant When windmilling the aerodynamic force reverses, so the ATM acts towards fine , adding to the CTM Pitch change mechanisms must overcome both pitch change axis total reaction CP ahead of the axis ATM towards COARSE Looking along the blade from the tip Normal running: ATM partly offsets CTM; CTM dominates Windmilling: ATM reverses and adds to CTM (to fine)
Chapter 29 · Propeller Principles
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The second twisting moment is aerodynamic. On a propeller blade the centre of pressure lies ahead of the pitch change axis, nearer the leading edge. The total reaction acts there, forward and to one side, and because it is offset from the axis it tries to rotate the blade towards a larger blade angle, that is towards coarse pitch. This is the aerodynamic twisting moment, A T M. In normal powered running the A T M works against the centrifugal twisting moment and cancels part of it, but the C T M is bigger, so the net tendency is still towards fine. Now the trap. When the propeller is windmilling, driven by the airflow, the angle of attack is negative and the aerodynamic force on the blade reverses. The A T M then acts towards fine as well, adding to the C T M. We will use this in the next lesson.
Propeller efficiency
Power out divided by power in Thrust power (power out) = thrust × TASShaft power (power in) = engine torque × rotational speedPropeller efficiency = thrust power ÷ shaft power Good propellers reach 80–88% at their design point Losses: kinetic energy left in the slipstream, its swirl, profile drag of the blades, tip losses Efficiency = thrust power ÷ shaft power Thrust power thrust × TAS 2 000 N × 60 m/s = 120 kW Shaft power torque × angular speed 600 N m × 251 rad/s = 151 kW 2 400 RPM = 40 rev/s = 251 rad/s η = 120 ÷ 151 ≈ 0.80 (80 %)
Chapter 29 · Propeller Principles
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
How good is a propeller at its job? We compare the useful power that comes out with the power that goes in. The power out is thrust power, which is thrust multiplied by true airspeed, because power is force times velocity. The power in is shaft power: the torque from the engine multiplied by the rotational speed. Propeller efficiency is thrust power divided by shaft power. Let us work an example. Two thousand newtons of thrust at sixty metres per second is one hundred and twenty kilowatts. The engine delivers six hundred newton metres at two thousand four hundred R P M, which is two hundred and fifty one radians per second, so the shaft power is about one hundred and fifty one kilowatts. The efficiency is one hundred and twenty divided by one hundred and fifty one, about eighty per cent. The rest is lost in the swirl and speed of the slipstream and in blade drag.
Efficiency and speed
A fixed pitch propeller is efficient at only one speed 0% 20% 40% 60% 80% 100% fine pitch zero thrust coarse pitch zero thrust variable pitch: blade angle changed with speed aircraft forward speed (at constant RPM) → propeller efficiency At rest: big thrust, zero TAS, so η = 0 . At the zero-thrust speed: η = 0 again. One peak in between. Varying the blade angle keeps η high over a wide range .
Chapter 29 · Propeller Principles
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is efficiency plotted against forward speed at constant R P M. Start with the blue curve, a fine pitch fixed propeller. At rest the thrust is large, but the airspeed is zero, so the thrust power, and therefore the efficiency, is zero. That is why holding an aircraft on the brakes at full power does no useful work. As speed rises the efficiency climbs to a single peak, where the blade is at its most efficient angle of attack. Beyond that the angle of attack keeps falling until, at some high speed, the blade reaches its zero lift angle, thrust disappears and efficiency is zero again. A coarse pitch fixed propeller, in brown, behaves the same way but peaks at a higher speed. Now imagine many blade angles: their curves form an envelope, the dashed purple line. A propeller whose blade angle can be varied with speed can ride along that envelope and stay efficient over a much wider range.
Variable pitch
From fixed pitch to constant speed Fixed pitch One blade angle for ever. Simple and light, but efficient at only one speed and RPM.
Ground adjustable Blades reset in the hub on the ground ; in flight it acts as a fixed pitch propeller.
Two pitch Fine for take-off, climb and landing, coarse for cruise, selected in flight; usually a feathered position too.
Constant speed Blade angle varied automatically to hold the RPM selected ; efficient over a wide TAS range.
Chapter 29 · Propeller Principles
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Designers have attacked the fixed pitch problem in stages. A fixed pitch propeller has one blade angle for ever. It is simple, light and cheap, but it is only at its best at one speed and R P M. A ground adjustable propeller lets an engineer reset the blades in the hub on the ground, perhaps finer for a short strip; in flight it is still a fixed pitch propeller. A two pitch propeller can be switched in flight between a fine setting for take-off, climb and landing and a coarse setting for the cruise, and it usually has a feathered position as well. Modern aircraft use the constant speed propeller. Its blade angle is varied automatically to hold whatever R P M the pilot selects, so it stays efficient over a wide range of true airspeed. That gives better take-off and climb performance and lower fuel consumption in the cruise.
Constant speed propeller
Throttle, prop lever and mixture Throttle : engine power (manifold pressure)Prop lever : selects the RPM ; the constant speed unit (CSU) sets the blade angle to hold itForward : fine pitch, high RPM , like first gear. Back : coarse pitch, low RPM , like fifth gearTake-off: throttle, prop and mixture all forward To reduce power for the cruise: throttle back first, then RPM ; to increase power: RPM up first, then throttle OPEN CLOSE THROTTLE manifold pressure INCR RPM DECR RPM PROP RPM (blade angle) RICH LEAN MIXTURE fuel/air ratio forward = fine = high RPM back = coarse = low RPM All forward: the take-off setting
Chapter 29 · Propeller Principles
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
In the cockpit of a light aircraft with a constant speed propeller there are three levers. The throttle sets engine power, shown on the manifold pressure gauge. The propeller lever does not set power directly; it selects an R P M, and the constant speed unit, the C S U, then varies the blade angle to hold that R P M. Push the prop lever forward and you select high R P M, which the C S U achieves with fine pitch. Pull it back and you select low R P M, with coarse pitch. A good way to remember it is a gearbox: forward is first gear, back is fifth gear. For take-off all three levers are fully forward. When reducing power after take-off or for the cruise, bring the throttle back first and then the R P M, using the settings in the flight manual. When increasing power, do the reverse: R P M up first, then the throttle.
Constant speed unit
Holding RPM through the take-off Start of the roll: RPM at maximum, TAS low, fine pitch ; α near its best value As TAS rises, α falls, so thrust and propeller torque fall Less resistance: the RPM tends to rise The CSU senses it and increases the blade angle to restore α and hold the RPM At high TAS the blades are in coarse pitch at the same RPM Take-off roll: CSU holds RPM, α stays near its best value β α direction of flight start of roll β 20°, α ≈ 11° β α climb speed β 41°, α ≈ 11° TAS ↑ CSU coarsens
Chapter 29 · Propeller Principles
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us watch the constant speed unit at work during a take-off. At the start of the roll the R P M is at maximum, the true airspeed is low and the blades are in fine pitch, with the angle of attack close to its best value. Now the aircraft begins to accelerate. The blade path steepens and the angle of attack falls, so the blades make less thrust and less propeller torque. With less resistance, the engine starts to speed up. The C S U senses that rise in R P M and responds: it starts to coarsen the blades, increasing the blade angle until the angle of attack, and the propeller torque, are back where they were, and the R P M is held. As the aircraft goes faster still, the same thing happens again: the angle of attack falls, the C S U coarsens again, and the R P M stays put. At high speed the blades end up in coarse pitch.
Constant speed unit
The governor loop RPM tends to RISE TAS up, throttle opened, or dive Governor: overspeed flyweights fly out against the speeder spring Blade angle INCREASES oil moves the blades towards coarse Torque rises, RPM back to the value set on the prop lever RPM tends to FALL TAS down, throttle closed, or climb Governor: underspeed spring wins, flyweights move in Blade angle DECREASES blades move towards fine Torque falls, RPM back to the selected value Within its pitch range the CSU keeps RPM constant whatever the throttle, airspeed or attitude Exam point: to keep the RPM constant when power is increased , the CSU must increase the blade angle .
Chapter 29 · Propeller Principles
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Inside the constant speed unit is a governor driven by the engine. Flyweights spin with the engine and are thrown outward by centrifugal force, against a speeder spring whose load is set by the prop lever. If the R P M tends to rise, for example because the airspeed increases, the throttle is opened or the aircraft dives, the flyweights fly out and the governor sends oil to move the blades towards coarse. The bigger blade angle raises the propeller torque and the R P M comes back to the selected value. If the R P M tends to fall, because the airspeed drops, the throttle is closed or the aircraft climbs, the spring wins, the blades move towards fine, the torque falls and the R P M recovers. Remember the classic question: with constant R P M, an increase in engine power needs an increase in blade angle, so that the propeller absorbs the extra power.
Constant speed unit
Blade angle through the flight Phase Prop lever / RPM TAS Blade angle Why Take-off Fully forward, max RPM Low Fine Max power absorbed at low speed, best α Climb Climb RPM Moderate Moderate CSU coarsens as speed builds Cruise Back to cruise RPM High Coarse Low RPM, high TAS: efficient, quiet, economical Descent, throttle reduced Cruise RPM held High Finer Less engine torque: CSU fines off to hold RPM Approach and landing Fully forward Low Fine Full power instantly available for a go-around Engine failure / throttle closed Any Any Goes fully fine CSU tries to hold RPM: windmilling (next lesson)
The CSU can only hold RPM within its pitch range : at the fine stop (low speed, low power) RPM falls; at the coarse stop (very high speed) it can overspeed.
Chapter 29 · Propeller Principles
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
For take-off the lever is fully forward, the airspeed is low, and the blades are fine, so the propeller absorbs full power and has the best angle of attack. In the climb the C S U coarsens the blades as speed builds. In the cruise you select a lower R P M at high airspeed, and the blades are coarse: efficient and economical. If you reduce the throttle for a descent, the engine torque falls, so the C S U fines the blades to hold the R P M. For approach and landing the lever goes fully forward, so that full power is available at once for a go around. And if the engine fails, the C S U still tries to hold the R P M and drives the blades fully fine; that is windmilling, which we study next. Remember that the C S U can only govern within its pitch range, between the fine and coarse stops.
Summary
What to take into the exam Blade angle Chord to plane of rotation , at 75% R. Small = fine, large = coarse. Falls root to tip (twist ).
Pitch and slip Geometric : advance per rev at the blade angle. Effective : actual advance. Slip = difference.
Angle of attack Chord to relative airflow. α = β − helix angle . Set by RPM and TAS .
Fixed pitch TAS ↑ → α ↓; RPM ↑ → α ↑. Best at one airspeed/RPM pair.
Forces Thrust ⟂ plane of rotation; torque in it. Thrust bends tips forward; peak well outboard.
CTM and ATM CTM → fine (dominant). ATM → coarse , but → fine when windmilling.
Efficiency Thrust power ÷ shaft power . Zero at rest and at zero thrust; one peak if fixed.
CSU Lever forward = fine/high RPM. RPM tends up → coarsen . More power at constant RPM → larger β .
Chapter 29 · Propeller Principles
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
The blade angle is measured from the plane of rotation to the chord, at seventy five per cent radius; small is fine, large is coarse, and it falls towards the tip because the tip moves faster. Geometric pitch is the advance per revolution at the blade angle, effective pitch is the real advance, and slip is the difference. The angle of attack is the blade angle minus the helix angle, and it depends on both R P M and true airspeed. For a fixed pitch propeller, more speed means less angle of attack and more R P M means more, so it is at its best at only one combination. Thrust acts at right angles to the plane of rotation and torque within it. The C T M turns blades to fine and dominates; the A T M turns them to coarse, except when windmilling. Efficiency is thrust power over shaft power. And the C S U coarsens the blades whenever the R P M tries to rise.