Principles of Flight · Revision
Revision and Exam Practice The formulas, numbers, rules and traps that principles of flight papers test again and again, with a full set of revision questions.
VMD V–n L = ½ρV²SCL formulas · numbers · rules · traps © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the revision chapter of the principles of flight course. Exam papers return again and again to the same few formulas, numbers and rules, and they set the same traps every time. In this chapter we gather all of them in one place: the airspeeds, the lift and drag equations, minimum drag and minimum power speeds, the stall speed rules, flaps and slats, stability and controls, turns and load factor, Mach effects, the manoeuvre envelope, windshear and propellers. After that you work through the full set of revision questions and a specimen paper.
How to use this chapter
The whole syllabus on twenty pages Each page gathers one block of the syllabus: the formulas, the numbers and the classic traps. Every revision question links back to one of them.
Air and lift Units, airspeeds, continuity and Bernoulli, the lift equation and the lift curve.
Drag and stalling Parasite and induced drag, VMD and VMP, boundary layers, stall speed rules, stall types and high lift devices.
Stability and control Longitudinal, lateral and directional stability, ailerons, tabs, mass balance and the trimming stabiliser.
Mechanics and limits Turns and climbs, high-speed flight, the V-n diagram, windshear and propellers. Then the questions.
Chapter 31 · Revision and Exam Practice
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This revision chapter squeezes the whole principles of flight syllabus onto about twenty pages. We work in four blocks. First the air and lift: units, the airspeeds, continuity and Bernoulli, the lift equation and the lift curve. Then drag and stalling: parasite and induced drag, the minimum drag and minimum power speeds, boundary layers, the stall speed rules, the different kinds of stall and the high lift devices. Third, stability and control. Fourth, the mechanics and limits: turns and climbs, high-speed flight, the manoeuvre envelope, windshear and propellers. On every page, look for three things: the formula, the number to remember, and the trap the examiner likes to set. After the last page you will find the full set of revision questions and a specimen paper, each linked back to the page that answers it.
Basics
Units and the physics behind them Quantity SI unit and what to remember Force newton , N = kg·m/s². Newton’s second law: F = m × a Weight W = m × g: a 50 t aircraft with g = 10 m/s² weighs 500 000 N Pressure, dynamic pressure, wing loading N/m² (pascal). Wing loading = W/S. psi is an imperial pressure unit, not SIDensity ρ kg/m³ ; ISA sea level 1.225 kg/m³. Falls with height and with higher temperatureWork, energy joule = N·mPower watt = N·m/s (work per second). Power required = drag × TASMach number TAS ÷ local speed of sound ; speed of sound depends only on temperature (661 kt in ISA at sea level)
Chapter 31 · Revision and Exam Practice
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Start with units, because they are easy marks. Force is measured in newtons, and one newton is one kilogram times one metre per second squared, which is just force equals mass times acceleration. Weight is mass times g, so a fifty tonne aircraft with g taken as ten weighs five hundred thousand newtons. Pressure, dynamic pressure and wing loading all share the same unit, newtons per square metre, the pascal. Psi is a pressure unit too, but an imperial one. Density is kilograms per cubic metre, one point two two five at sea level in the standard atmosphere, and it falls as height or temperature rises. Work is the joule, a newton metre, and power is work per second, newton metres per second, the watt. Remember too that power required is drag multiplied by true airspeed. Finally, Mach number is true airspeed divided by the local speed of sound, which depends only on temperature.
Airspeeds
IAS, CAS, EAS, TAS and Mach IAS → instrument and position error → CAS → compressibility → EAS → density → TAS TAS = EAS ÷ √(relative density): above sea level TAS > EAS ; below sea level TAS is lower The IAS–TAS gap grows as density falls: higher, or warmer; it shrinks as you descend Climb at constant CAS: TAS and Mach rise . Descend at constant Mach: CAS rises , watch VMO Compressibility is judged by Mach number ; stall, VMD and VA are IAS (EAS) values 0 10000 20000 30000 40000 150 250 350 450 550 Pressure altitude (ft) Speed (kt) 0.30 0.45 0.60 0.75 0.90 Mach number tropopause CAS 290 kt held CAS falls TAS Mach crossover ≈ 30900 ft: hold M 0.78 TAS = EAS ÷ √σ · Mach = TAS ÷ a, a = 38.94 √T kt climb at constant CAS: TAS and Mach rise · constant Mach descent: CAS rises
Chapter 31 · Revision and Exam Practice
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The airspeed chain runs from indicated airspeed, corrected for instrument and position error to give calibrated airspeed, then for compressibility to give equivalent airspeed, then for density to give true airspeed. The air speed indicator is calibrated for sea-level density, so true airspeed equals equivalent airspeed divided by the square root of the relative density. Higher up, or in warmer air, the density is lower and true airspeed is greater than indicated; below sea level it is lower. So the gap between indicated and true airspeed grows as you climb and shrinks as you descend. The chart shows a typical airliner climb at two hundred and ninety knots calibrated. True airspeed and Mach number both rise, until at about thirty-one thousand feet the Mach number reaches point seven eight. From there the crew holds Mach, and calibrated airspeed falls. Turn it round: descending at constant Mach, the calibrated airspeed rises towards the maximum operating speed.
Continuity and Bernoulli
Mass flow, static and dynamic pressure Continuity : ρ × A × V = constant mass flow; at low speed (below M 0.4) simply A × V = constant Bernoulli : total pressure = static + dynamic: PT − PS = q , with q = ½ρV²Convergent : speed up, static pressure down. Divergent : speed down, static pressure upVenturi throat: dynamic ↑, static ↓, total unchanged ; density treated as constant Static pressure acts in all directions ; warmer air in a stream tube: density ↓, speed ↑, same mass flowV₁ V₂ (fastest) V₃ = V₁ static pressure: high · low · high total pressure constant dynamic q = ½ρV² static
Chapter 31 · Revision and Exam Practice
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two laws explain low-speed airflow. Continuity says the mass flowing through a stream tube is the same at every section: density times area times velocity is constant. Below about Mach point four we treat the density as fixed, so area times velocity is constant, and where the tube narrows the air must speed up. Bernoulli says that in steady flow the total pressure, which is static pressure plus dynamic pressure, stays constant. Dynamic pressure is half rho V squared. So total minus static equals dynamic. Put the two together in a venturi: through the convergent part the speed rises and the static pressure falls, as the gauge on the throat shows, while the total pressure stays the same; through the divergent part the speed falls and the static pressure recovers. Remember that static pressure acts equally in all directions. And if you heat the air in a stream tube, its density falls, so to carry the same mass flow it must move faster.
Lift
The lift equation and its angles L = ½ρV² · S · CL : dynamic pressure × wing area × lift coefficientLift is perpendicular to the relative airflow, drag parallel ; both act at the centre of pressure Angle of attack : chord to relative airflow · incidence : chord to longitudinal axis · pitch : axis to horizonLevel flight: CL ∝ 1/V². Double the IAS → CL × ¼ . At 1.3 VS , CL = 1/1.69 = 59 % of CLmax Same weight and IAS higher up: same angle of attack, higher TAS Most lift comes from suction on the upper surface relative airflow chord line α Lift ⟂ airflow Drag ∥ total reaction centre of pressure L = ½ ρ V² · S · CL q = ½ρV² (N/m²) · S = wing area · CL set by α and section Angle of attack: chord ↔ relative airflow Incidence: chord ↔ longitudinal axis (fixed) Pitch angle: longitudinal axis ↔ horizon
Chapter 31 · Revision and Exam Practice
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The lift equation is the backbone of the whole subject. Lift equals half rho V squared, the dynamic pressure, times the wing area S, times the lift coefficient. Lift is at right angles to the relative airflow and drag along it, both acting at the centre of pressure. Keep the angles apart. Angle of attack is between the chord line and the relative airflow. The angle of incidence is between the chord and the longitudinal axis, fixed by the designer. Pitch angle is between the longitudinal axis and the horizon. In level flight lift equals weight, so the lift coefficient varies as one over V squared. Double the indicated airspeed and the lift coefficient must fall to a quarter. At one point three times the stall speed it is one over one point six nine, about fifty-nine per cent of its maximum. Watch the section as the angle of attack grows, then grows further, and finally reaches the critical angle.
The lift curve
CL against angle of attack, clean and with devices -10° -5° 0° 5° 10° 15° 20° 25° 30° -0.5 0.0 0.5 1.0 1.5 2.0 2.5 Angle of attack α (degrees, to the clean chord line) Lift coefficient CL CLmax clean ≈ 16° flap: CLmax ↑, stall α ↓ slat: stall α ↑ zero lift ≈ −4° CL > 0 at α = 0 symmetrical cambered (clean) + trailing edge flap + leading edge slat Rules from the curve Slope ≈ 0.1 per degree straight until near the stall Symmetrical section no lift and no pitching moment at α = 0 Cambered section lift at α = 0: curve cuts the CL axis above 0 Level flight: CL ∝ 1/V² 2 × IAS → ¼ CL · 1.3 VS → 59 % CLmax Trailing edge flap camber: CLmax ↑, stalling angle ↓ Leading edge slat energy: stalling angle ↑, CLmax ↑ Ice, frost, heavy rain CLmax ↓, stalling angle ↓, drag ↑
Chapter 31 · Revision and Exam Practice
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
This one chart answers a whole family of questions. The lift coefficient rises in a straight line with angle of attack, about point one per degree, then rounds over to its maximum at the critical angle, roughly sixteen degrees for a clean wing, and falls away beyond the stall. A symmetrical section gives no lift at zero angle of attack and has no pitching moment about its aerodynamic centre. A cambered section already gives lift at zero, so its curve cuts the vertical axis above the origin, and it only reaches zero lift at about minus four degrees. Trailing edge flaps add camber: the curve moves up and to the left, so the maximum lift coefficient rises but the stalling angle falls. Leading edge slats do something different: they let the same line carry on to a higher angle of attack, so both the maximum lift coefficient and the stalling angle increase. Ice or heavy rain does the opposite, lowering both.
Drag and power
The drag curve and the power curve 100 150 200 250 300 350 0 20 40 60 80 100 120 140 IAS (kt) Drag (relative units) VMD : minimum drag, L/D max parasite = induced total parasite ∝ V² induced ∝ 1/V² speed unstable speed stable 100 150 200 250 300 350 0 10 20 30 40 TAS (kt) Power required (relative) VMP ≈ 0.76 VMD minimum power: longest time airborne VMD ≈ 1.32 VMP tangent from the origin P = D × TAS Sea level, so IAS = TAS. Parasite ∝ V², induced ∝ 1/V²; at VMD they are equal and L/D is maximum. VMP ≈ 0.76 VMD .
Chapter 31 · Revision and Exam Practice
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the two curves you must be able to draw from memory. On the left, drag against speed. Parasite drag grows with the square of the speed, so double the speed gives four times the parasite drag. Induced drag goes the other way, falling with one over V squared, so double the speed gives a quarter. Their sum, total drag, is high when slow and high when fast, with a minimum where the two parts are equal. That is the minimum drag speed, V M D, where the lift to drag ratio is greatest, at about four degrees angle of attack. On the right, power required, which is drag times true airspeed. Its minimum, V M P, is slower, about nought point seven six of V M D. A line from the origin touches the power curve exactly at V M D, which is about one point three two times V M P.
Induced drag
Tip vortices, aspect ratio and ground effect Air spills bottom to top round the tip ; spanwise flow is inward on top, outward underneath Downwash tilts the effective airflow: induced angle of attack , lift tilts back → induced drag CDi ∝ CL ² / AR ; at constant weight Di ∝ 1/V²; heavier → more induced dragHigh aspect ratio (span ÷ mean chord), winglets , tip tanks reduce it; vortex generators do not Vortices strongest slow, heavy and clean ; flap down weakens the tip vortices Ground effect within about half a span: downwash ↓, induced drag ↓, lift ↑, longer landing Seen from above: spanwise flow and tip vortices orange: upper surface, inward · blue dashed: lower surface, outward tip vortex Rules CDi ∝ CL ² ÷ aspect ratio · AR = span ÷ mean chord = b²/S Constant weight: Di ∝ 1/V² · IAS ×2 → CDi ×1/16, Di ×¼ Reduced by: high AR, winglets, tip tanks, flap (weaker tip vortices) Ground effect (within ½ span): downwash ↓, Di ↓, lift ↑, the lift vector tilts forward, and the landing distance increases
Chapter 31 · Revision and Exam Practice
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Induced drag is the price of lift. Underneath the wing the pressure is higher than at the tip and on top it is lower, so air spills round the tip from the bottom to the top. That gives a spanwise flow inward on the upper surface and outward on the lower, and it rolls up into a tip vortex behind each tip. The vortices add downwash, which tilts the effective airflow down by the induced angle of attack, and the lift, at right angles to it, tilts backwards. That backward component is induced drag. Its coefficient is proportional to C L squared divided by aspect ratio, so at a fixed weight it falls with the square of the speed and it rises with weight. The vortices are strongest when the aircraft is slow, heavy and clean. Close to the ground, within about half a span the ground squashes the vortices and the downwash. Induced drag falls and lift rises, so the aircraft floats and the landing distance increases.
Boundary layer and drag types
Where parasite drag comes from Topic Remember Laminar layer Thin, low skin friction, no flow normal to the surface , little energy, so it separates easily Turbulent layer Thicker, more skin friction , more kinetic energy, so it resists separation Separation Starts at the trailing edge of the upper surface and moves forward as α rises Vortex generators Mix high-energy free-stream air into the layer to delay separation Form and skin friction Pressure difference fore and aft / surface shear. Gear down: form drag up and a nose-down moment Interference drag Boundary layers mixing at junctions : wing and fuselage, pylons, struts Drag scaling D = ½ρV²·CD ·S: area ×3 → drag ×3 · density ½ → drag ½ · speed ×4 → parasite ×16 Induced drag scaling Constant weight, IAS ×2: CL ×¼, CDi ×1/16, Di ×¼
Chapter 31 · Revision and Exam Practice
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Parasite drag comes from the boundary layer and from the shape. A laminar boundary layer is thin and gives little skin friction, and its defining mark is that there is no flow normal to the surface. But it has little energy, so it separates easily. A turbulent layer is thicker and rubs harder, giving more skin friction, but its extra kinetic energy lets it stay attached longer. Separation begins at the trailing edge of the upper surface and creeps forward as the angle of attack increases. Form drag comes from the pressure difference between front and back; lowering the gear adds form drag and, because the gear is below the centre of gravity, a nose-down moment. Interference drag appears where boundary layers meet at junctions. Then practise the scaling: drag is proportional to density, area and speed squared. And for induced drag at a fixed weight, doubling the indicated airspeed cuts the coefficient to a sixteenth and the drag itself to a quarter.
Stall speed rules
Weight, load factor, CG and contamination A wing stalls at the critical angle of attack (about 16° clean), at any speed or attitude Weight: VS2 = VS1 × √(W2 /W1 ) : 132 kt × √1.5 = 162 kt Turn: n = 1/cos φ and VS rises with √n : 45° → lift +41 %, VS +19 %; 60° → n = 2, VS +41 % Forward CG : more tail down-force → higher VS ; stall angle unchanged by CG or weightIce, frost, heavy rain: CLmax and stall angle fall , drag and weight rise Warning senses angle of attack (vane at the stagnation point): its kt margin stays the same at any weight 0° 15° 30° 45° 60° 75° 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Bank angle φ (degrees) Factor 1.15 1.41 1.19 2.00 1.41 load factor n = 1/cos φ stall speed factor √n VS turn = VS1g × √n · VS2 = VS1 × √(W₂ / W₁) 15° bank 60 kt → VS1g 59 kt → 45° bank 70 kt · 1.4 VS margin → stall at 60° bank
Chapter 31 · Revision and Exam Practice
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The stall happens at the critical angle of attack, about sixteen degrees for a clean wing, whatever the speed or attitude. It varies with the square root of weight: one hundred and thirty-two knots at one weight becomes one hundred and sixty-two knots at one and a half times that weight. In a level turn the load factor is one over the cosine of the bank angle, and the stall speed rises with the square root of the load factor. At forty-five degrees of bank you need forty-one per cent more lift, and the stall speed rises by nineteen per cent. At sixty degrees the load factor is two and the stall speed rises by forty-one per cent. Move the centre of gravity forward and the tail needs more down-force, so the stall speed rises, but the stalling angle does not change. Ice and heavy rain lower the maximum lift coefficient and the stalling angle.
Stall behaviour
Straight, swept, deep and shock stalls Straight wing: root stalls first, CP moves aft , the nose drops Swept-back wing: spanwise flow → tip stall , CP moves forward → pitch-up Swept wing + T-tail : wake blankets the tail → deep stall ; a stick pusher pushes at a set α Stall α: shock stall lowest , deep stall highest ; an accelerated stall (n > 1) is at the normal α Recovery: reduce α , full power, wings level (rudder on light aircraft) Spin: idle, ailerons neutral , full opposite rudder , then stick forward Straight wing Swept-back wing root stalls first CP moves aft nose drops: safe ailerons keep working stall warning by buffet tips stall first orange: spanwise flow CP moves forward pitch-up → deep stall T-tail in the wake cure: fences, vortilons, stick pusher Stall angle: shock stall lowest · deep stall highest
Chapter 31 · Revision and Exam Practice
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
How a wing stalls matters as much as when. A straight rectangular wing stalls at the root first, so the centre of pressure moves aft and the nose drops. A swept-back wing is different. Spanwise flow on the upper surface thickens the boundary layer towards the tips, so the tips stall first. The tips lie behind the centre of gravity, so losing their lift moves the centre of pressure forward and the aircraft pitches up, which drives it deeper into the stall. Add a T-tail and the separated wake can blanket the tailplane, leaving the elevator unable to recover: the deep, or super, stall. Such aircraft carry a stick pusher, which pushes the column forward at a set angle of attack. For the exam, the shock stall happens at the smallest angle of attack and the deep stall at the largest. To recover from any stall, reduce the angle of attack. In a spin: power to idle, ailerons neutral, full opposite rudder, then the stick forward.
High lift devices
Flaps add camber, slats add energy TE flaps: CL and CLmax ↑ , stall angle ↓ , L/D ↓ (most at the last stages of flap) Slats form a slot : boundary layer energy ↑, stall angle ↑ ; Krueger flaps (no slot) go inboard Flap out at constant IAS : CL unchanged, α reduced · at constant α : CL ↑, the aircraft climbs Flap in: raise α to stay level. Slats retract after flaps: big VS gain for little drag Pitch: CP aft (nose-down) against less tail downwash (nose-up): depends ; high T-tail → nose-down Glide with flap: L/D ↓ → steeper glide, shorter range, more sink slat + slot energises the boundary layer Fowler flap: area + camber main wing CLmax Stall α L/D Slot TE flap ↑ ↓ ↓ slotted types Slat ↑ ↑ ≈ yes Krueger ↑ ↑ ≈ no (inboard) Spoiler ↓ ↓ ↓ —
Chapter 31 · Revision and Exam Practice
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two families of devices, two different jobs. Trailing edge flaps add camber. They raise the lift coefficient at every angle and the maximum lift coefficient, but they lower the stalling angle and always reduce the lift to drag ratio, the last stages of flap most of all. Leading edge slats open a slot that feeds high-energy air over the top of the wing. They let the wing reach a higher angle before it stalls. Krueger flaps, which form no slot, are fitted inboard on swept wings so that the root still stalls first. Now the level-flight rules. Lower flap at constant indicated airspeed: the lift coefficient must stay the same, so the angle of attack is reduced. Lower flap at constant angle of attack: the lift coefficient rises and the aircraft climbs. Raise flap and you must increase the angle of attack. The pitching moment with flap depends on the design; with a high T-tail it is nose-down.
Longitudinal stability
CG, neutral point and stick forces Static = first tendency; dynamic = the motion over time. Statically unstable → never dynamically stable Stable: an up-gust gives a nose-down moment; gust lift acts at the aerodynamic centre CG must be ahead of the neutral point ; the gap is the static margin CG aft: stability ↓, stick force per g ↓ , less elevator per g · CG forward: flare limit (full flap, idle) Stick force per g needs upper and lower limits ; count from 1 g: 150 lb/g × 1.5 = 225 lb at 2.5 g Trim does not change stick force stabilityCG range and the neutral point forward limit elevator power: flare aft limit stability, stick force/g neutral point zero stability CG range minimum static margin nose Dynamic stability after a disturbance stable: oscillation dies away neutral: oscillation stays unstable: oscillation grows statically unstable → can never be dynamically stable
Chapter 31 · Revision and Exam Practice
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Stability questions start with two words. Static stability is the first tendency after a disturbance: does the aircraft start to return? Dynamic stability is what then happens over time: do the oscillations die away, stay the same or grow? An aircraft that is statically unstable can never be dynamically stable. A stable aircraft meets an up-gust with a nose-down moment. For stability the centre of gravity must lie ahead of the neutral point; the distance between them is the static margin. Moving the centre of gravity aft reduces stability and reduces the stick force and elevator travel needed per g, so the aft limit protects stability and stick force per g, which must have both upper and lower limits. The forward limit is set by elevator power, worst when flaring with full flap at idle. In stick force questions count from one g: at two point five g the increment is one point five g, so one hundred and fifty pounds per g gives two hundred and twenty-five pounds.
Lateral and directional
Sideslip, Dutch roll and spiral Lateral stability: roll away from the sideslip . Positive sideslip = nose left → roll left Add lateral stability: dihedral , high wing , sweepback . Anhedral and low wing reduce it Directional: fin and fuselage behind the CG; sweepback is stabilising too Lateral stronger than directional → Dutch roll ; directional stronger → spiral instability Too much lateral stability: large aileron inputs in crosswind landings A yaw damper deals with Dutch roll Sideslip to the right (positive β: nose left) relative wind from the right lower wing meets the wind: more α rolls left, away from the slip rear view · dihedral Dutch roll Spiral instability lateral stability stronger than directional yaw and roll out of phase cure: yaw damper directional stability stronger than lateral slowly tightening descent pilot corrects easily
Chapter 31 · Revision and Exam Practice
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Lateral stability is about rolling in a sideslip. In a sideslip the relative wind comes from one side, and a laterally stable aircraft rolls away from it, raising the lower wing. The examiners define a positive sideslip angle as nose left, so the stable reply is a roll to the left. Dihedral, a high wing and sweepback all add lateral stability; anhedral and a low wing take it away. Directional stability is weathercock stability, from the fin and the side area behind the centre of gravity, and sweepback adds to it as well. The balance between the two decides the dynamic behaviour. If lateral stability dominates, the aircraft tends towards Dutch roll, the out-of-phase yawing and rolling you see in the wingtip trails here. If directional stability dominates, it tends towards spiral instability, a slowly steepening descending turn. Too much lateral stability is also a nuisance on a crosswind landing, because the pilot needs large aileron inputs to hold the wing down.
Controls
Ailerons, tabs, balance and trim Cruise: inboard ailerons + roll spoilers ; outboard ailerons locked out with flaps up Differential ailerons : the up-going one moves further: left roll = left up 5°, right down 2°Tabs move opposite to the surface (not the anti-balance tab): slower → elevator up, tab down Mass balance ahead of the hinge line stops flutterTrimming stabiliser: nose-heavy → leading edge lower ; used because tabs are not powerful enough Flare: the biggest pull with CG forward and full flap Roll control at cruise (right wing from above) inboard aileron: active outboard aileron: locked out roll spoilers flaps (up) Speed reduced, retrimmed (side view) elevator up tab down mass balance ahead of the hinge tabs move opposite to their surface (except the anti-balance tab)
Chapter 31 · Revision and Exam Practice
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Control questions are about which surface moves which way. At high speed a large jet locks out its outboard ailerons, which could twist the wing and reverse, and rolls with its inboard ailerons helped by roll spoilers. Differential ailerons move the up-going aileron through a larger angle than the down-going one, to reduce adverse yaw, so a roll to the left might be left aileron up five degrees and right aileron down two. Tabs move opposite to their control surface, except the anti-balance tab. So if the speed falls and you hold the nose up, the elevator goes up and the trim tab moves down to hold it there. Mass balance weights sit ahead of the hinge line to bring the surface centre of gravity forward and prevent flutter. A trimming stabiliser is used on large aircraft because a tab would not be powerful enough; for a nose-heavy aircraft its leading edge is set lower, to give more tail down-force.
Turns, climbs and glides
Load factor, radius, rate and gradient n = L/W = 1/cos φ : 45° bank → L = 1.41 W (50 000 N → 70 700 N ); same bank → same n at any speedRadius R = V²/(g · tan φ) ; rate = V/R: same bank, faster → wider turn, slower rate Climb gradient ≈ (T − D)/W : (120 000 − 41 667)/500 000 = 15.7 % Steady climb or descent: L < W , load factor slightly below 1 Glide angle depends only on L/D ; weight changes the speed, not the angle VMCL : landing configuration, roll 20° away from the dead engine in 5 s Lift = n × W L cos φ = W L sin φ: turns Weight φ n = 1/cos φ 30° → 1.15 · 45° → 1.41 · 60° → 2.0 R = V²/(g tan φ) rate = V/R = g tan φ / V Climb gradient (T − D)/W ≈ sin γ · L < W in a climb
Chapter 31 · Revision and Exam Practice
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a level turn the lift is tilted, so it must grow until its vertical part still equals the weight. The load factor, lift over weight, is one over the cosine of the bank angle, and it depends only on bank. At forty-five degrees it is one point four one, so fifty thousand newtons of lift in level flight becomes about seventy thousand seven hundred. The radius is V squared over g tan phi, and the rate of turn is speed over radius. So two aircraft at the same bank have the same load factor, but the faster one flies a wider circle at a slower rate. In a straight climb, thrust must balance drag plus the backward part of the weight, so the climb gradient is thrust minus drag, over weight. Fifty tonnes, two engines of sixty thousand newtons and a lift to drag ratio of twelve give fifteen point seven per cent. And the glide angle depends only on the lift to drag ratio.
High-speed flight
Mcrit, shocks and their effects Mcrit : free-stream Mach at which the local flow first reaches M 1.0 Transonic: Mcrit to about M 1.3 ; a bow wave forms just above M 1 Through a shock: speed ↓, pressure, temperature, density ↑ . Expansion: Mach ↑, temperature and speed of sound ↓ Tuck under : shock moves aft → CP aft and less downwash at the tail → nose-downBuffet margin shrinks with altitude and grows as you descend at constant IAS Descending at constant Mach → IAS rises → VMO normal shock behind it: subsonic, p, T, ρ jump up supersonic region local M > 1 M 0.8 CP moves aft: tuck under Subsonic below Mcrit : no local supersonic flow Transonic Mcrit to about M 1.3: mixed flow, shocks Bow wave appears just above M 1.0 Expansion wave Mach ↑, p ↓, temperature and speed of sound ↓
Chapter 31 · Revision and Exam Practice
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
High-speed flight begins at the critical Mach number, the free-stream Mach number at which the air somewhere on the aircraft first reaches the speed of sound. From there to about Mach one point three is the transonic range, with mixed subsonic and supersonic flow. Watch the section: at Mach point seven two the flow is still subsonic, then a supersonic bubble grows over the upper surface and ends in a shock wave. Through a shock the air slows suddenly, and its pressure, temperature and density jump up. Through an expansion wave the opposite happens: the Mach number rises while the temperature, and with it the local speed of sound, falls. A bow wave first appears just above Mach one. As the shock moves aft the centre of pressure moves aft and the downwash at the tail falls, giving the nose-down tuck under. The shock can also separate the flow, the shock stall. The gap between low and high speed buffet shrinks as you climb and widens as you descend.
Limitations
The manoeuvre envelope (V-n diagram) 0 50 100 150 200 250 300 350 -1 0 1 2 2.5 3 3.75 Equivalent airspeed (kt) Load factor n ultimate load 1.5 × 2.5 = 3.75 VS VA VC VD 1 g stall A: stall line meets +2.5 g positive limit +2.5 (flaps down +2.0) negative limit −1.0 stall boundary (CLmax ): n = (V/VS )² safe envelope Limits to remember VA = VS1g × √nlimit 60 kt × √2.5 = 95 kt VA falls when lighter VS ∝ √W, so VA ∝ √W Above VA full nose-up elevator may cause permanent deformation Large aircraft +2.5 to −1.0 g clean · +2.0 to 0 g flaps down Utility / aerobatic +4.4 / +6.0 g · −1.76 / −3.0 g Gust load CL 0.42 + 3° × 0.1 → n = 0.72/0.42 = 1.7 Gust lift acts at the aerodynamic centre
Chapter 31 · Revision and Exam Practice
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The manoeuvre envelope plots load factor against equivalent airspeed. The curved boundary on the left is the stall: the most lift the wing can give rises with speed squared, so the load factor available there is speed over stall speed, squared. Large transport aircraft are designed to a limit load factor of plus two point five and minus one, or plus two with flap down; the ultimate load, with the safety factor of one point five, is three point seven five. Where the stall curve meets the limit is the speed where a full pull just reaches the limit, and design manoeuvring speed, V A, is based on it: stall speed times the square root of the limit load factor. Sixty knots and two point five give ninety-five knots. Because stall speed depends on weight, V A does too: lighter means slower. Above V A a full nose-up elevator input can overstress the structure and cause permanent deformation.
Windshear
The microburst on approach and take-off Microburst: downdraught under 1 mile across, outflow to about 2½ miles (4 km) , up to 6000 ft/min Lasts under 15 min ; strongest winds for about 2–4 min Headwind increase: IAS ↑, aircraft goes above the path · tailwind or downdraught: IAS ↓, sinks below The trap: power cut for the headwind is missing when the tailwind arrives Recovery: maximum thrust , pitch up towards stick shaker, keep the configuration, do not chase speed Best defence: avoid : delay take-off or approach near thunderstorms thunderstorm base glide path 1 · headwind ↑ IAS ↑, above the path 2 · downdraught 3 · tailwind: IAS ↓, sink outflow ≈ 2½ miles (4 km) Downdraught under 1 mile wide, up to 6000 ft/min · lasts under 15 min Recovery: maximum thrust, pitch towards stick shaker, keep the configuration, do not chase airspeed
Chapter 31 · Revision and Exam Practice
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
A microburst is a small, violent downdraught from a thunderstorm. It is typically less than a mile across as it comes down, spreads out along the ground to around two and a half miles, and the downdraught can reach six thousand feet per minute. One rarely lasts more than fifteen minutes, with its strongest winds for two to four minutes. Fly through it on approach and the sequence is cruel. First you meet the outflow as an increasing headwind: indicated airspeed rises and the aircraft balloons above the glide path, so the natural reaction is to reduce power. Then you pass through the downdraught and into a tailwind: airspeed and lift fall away and the aircraft sinks below the path, now with less power set. Recovery is maximum thrust and pitch up towards the stick shaker, keeping the configuration and not chasing airspeed. The best defence is to avoid it.
Propellers
Blade angle, pitch control and the four effects Blade angle = angle of attack + helix angle. At fixed pitch, more TAS → α falls Fixed pitch: efficient at one speed. Constant speed : near-peak efficiency over a wide speed range Take-off: fine pitch, maximum RPM . Idle glide: finer → windmilling drag ↑, L/D ↓, sink ↑ Feathered (about 90°): least drag after an engine failureClockwise from behind: torque rolls left ; slipstream and asymmetric blade (high α) yaw left Gyroscopic: pitch up → yaw right ; pitch down → yaw left plane of rotation TAS rotational speed relative airflow β blade angle 32° φ helix 23° α = β − φ = 9° thrust blade moves this way More TAS at the same RPM and β → φ grows → α falls Constant speed: β changes to keep α near the best value Clockwise from behind: torque roll left, slipstream yaw left, asymmetric blade yaw left, pitch up → gyroscopic yaw right
Chapter 31 · Revision and Exam Practice
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each propeller blade section meets air coming from two directions, the rotation and the true airspeed, so its angle of attack is the blade angle minus the helix angle. With a fixed-pitch propeller, increasing the true airspeed at the same rpm reduces the angle of attack, so the propeller is efficient at only one speed. Watch the angle shrink as the aircraft goes faster. A constant speed propeller changes its blade angle to keep the angle of attack near the best value, giving nearly maximum efficiency over a wide speed range. Take off in fine pitch at maximum rpm. In an idling glide a finer pitch makes the windmilling propeller drag more, so the lift to drag ratio falls and the sink rate rises; feathering gives the least drag. For a propeller turning clockwise as seen from behind: torque reaction rolls the aircraft left, the spiral slipstream and the asymmetric blade effect yaw it left, and gyroscopic precession turns a pitch-up into a yaw to the right.
Classic traps
Where marks are lost Stall is an angle The wing stalls at the critical α at any speed or attitude. Weight and CG change VS , not the stall angle.
Root or square? VS ∝ √W and √n . Parasite drag ∝ V² , induced ∝ 1/V² , lift coefficient ∝ 1/V².
Count from 1 g Stick force increments start at 1 g: 2.5 g is +1.5 g . A 45° turn is +41 % lift, +19 % VS .
Positive sideslip Defined as nose left ; the laterally stable reply is a roll to the left .
Which way the CP goes Straight wing stall: aft . Swept wing stall: forward (pitch-up). Transonic: aft (tuck under).
Flaps and slats Flaps lower the stalling angle, slats raise it. Both raise CLmax ; flaps always cut L/D.
Ground effect Less induced drag and more lift , so the aircraft floats and the landing distance increases .
Constant Mach descent IAS rises as you descend at constant Mach, so the limit to watch is VMO , not MMO .
Chapter 31 · Revision and Exam Practice
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
These are the places where marks are lost. The stall is an angle: weight and centre of gravity change the stall speed, never the stalling angle. Square or square root: stall speed goes with the square root of weight and of load factor, while parasite drag goes with speed squared and induced drag with one over speed squared. Count from one g: two point five g is an increment of one point five g, and a forty-five degree turn needs forty-one per cent more lift but raises the stall speed by only nineteen per cent. A positive sideslip is nose left, so the stable reply is a roll to the left. The centre of pressure: aft when a straight wing stalls, forward when a swept wing stalls, and aft again in tuck under. Flaps lower the stalling angle; slats raise it. Ground effect lengthens the landing. And descending at constant Mach the indicated airspeed rises, so the limit to watch is V M O.
Summary
Your last-minute list Lift L = ½ρV²SCL . 1.3 VS → 59 % CLmax . Cambered: lift at α = 0.
Drag D = ½ρV²SCD . CDi ∝ CL ²/AR. VMD : parasite = induced, best L/D. VMP ≈ 0.76 VMD .
Stall VS × √(W ratio), × √n. n = 1/cos φ. Swept wing: tip stall, pitch-up.
Devices Flaps: CLmax ↑, stall α ↓, L/D ↓. Slats: stall α ↑. Krueger inboard.
Stability CG ahead of NP. Aft CG: less stability, lower stick force per g. Lateral dominant → Dutch roll.
Mechanics R = V²/g tan φ. Gradient = (T − D)/W. Glide angle from L/D only. L < W in climb.
High speed Transonic Mcrit –1.3. Shock: p, T, ρ up. Expansion: Mach up, a down. Tuck under: CP aft.
Limits and props VA = VS √n, falls with weight. +2.5/−1 g. Props: torque roll left, pitch up → yaw right.
Chapter 31 · Revision and Exam Practice
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is your last-minute list. Lift: half rho V squared S C L, and at one point three times the stall speed you use fifty-nine per cent of the maximum lift coefficient. Drag: half rho V squared S C D, with the induced part going as C L squared over aspect ratio; at the minimum drag speed parasite equals induced and the lift to drag ratio is best, and the minimum power speed is about three quarters of it. Stall: speed goes with the square root of weight and of load factor, and a swept wing stalls at the tips and pitches up. Devices: flaps raise maximum lift but lower the stall angle; slats raise the stall angle. Stability: keep the centre of gravity ahead of the neutral point. Mechanics: the turn radius formula, the climb gradient formula, and glide angle from lift to drag ratio alone. Limits: V A equals stall speed times root n, plus two point five and minus one g. Now go to the questions.