Principles of Flight · Chapter 20
Roll, Yaw and Trim How ailerons, spoilers and the rudder roll and yaw the aeroplane, the side effects they bring, and how trim tabs and stabiliser trim take the load off the pilot.
roll right aileron up + spoilers aileron down © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter twenty carries on from the flying controls into roll, yaw and trim. We see how ailerons and spoilers roll the aeroplane and why a roll is opposed by damping, why a roll to the left makes the nose swing right, and how designers cure it. We meet aileron reversal, speed brakes and lift dumpers, then the rudder, the fin stall and the minimum control speed. We finish with the side effects of each control, and every way of trimming the aircraft so that it flies hands off.
Roadmap
Roll, yaw, and flying hands off Part 1 rolls the aeroplane, part 2 slows it down, part 3 yaws it, and part 4 trims it.
1 · Roll Ailerons, damping, rate of roll, adverse yaw and its cures, reversal, inboard ailerons, roll spoilers.
2 · Drag devices Speed brakes, their effect on V M D, and lift dumpers on the ground.
3 · Yaw Rudder, fin stall and dorsal fins, VMC, rudder ratio changers, secondary effects.
4 · Trim Trim tabs and their sense, stabiliser trim, forward CG, spring bias, fuel transfer, feel trim.
Chapter 20 · Roll, Yaw and Trim
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson builds directly on the last one. In part one we roll the aeroplane: how ailerons work, why a roll does not keep accelerating, how the rate of roll depends on true airspeed and wingspan, why ailerons swing the nose the wrong way, and how designers cure that. We will also meet aileron reversal and the spoilers that help or replace ailerons on jets. Part two covers the devices that slow an aircraft down: speed brakes in the air and lift dumpers on the runway. Part three is yaw: the rudder, the stalling of the fin, the minimum control speed with an engine failed, and the coupling between roll and yaw. Part four is trimming, so that the aircraft flies hands off, with tabs, a trimming tailplane, springs, fuel transfer and the artificial feel unit.
Part 1 · Lateral control
Ailerons give a rate of roll Roll control: ailerons , spoilers , or both. The key requirement is an adequate rate of roll Wheel right: right aileron up (less lift), left aileron down (more lift) A down aileron adds camber: that wing's stalling angle is reduced Ailerons are rigged drooped on the ground; in flight suction floats them up into line, cutting drag Centre the wheel and the roll stops , but the bank stays Seen from behind: wheel turned right more lift less lift left aileron down right aileron up roll right Aileron droop (rigging) on the ground: slightly down in flight: floats up, in line
Chapter 20 · Roll, Yaw and Trim
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Control in roll comes from ailerons, from spoilers, or from both together, and the main requirement is simply an adequate rate of roll. Turn the wheel to the right and the right aileron goes up, reducing the lift on the right wing, while the left aileron goes down, increasing the lift on the left wing. The aircraft rolls to the right. Remember from last lesson that a down-going aileron adds camber, so although that wing makes more lift, its stalling angle is reduced; harsh aileron near the stall can drop the wing. Ailerons are usually rigged slightly drooped, so on the ground they sit a little below the trailing edge. In flight the low pressure above sucks them up into perfect alignment, which keeps drag low. Watch what happens when you centre the wheel: the roll stops, but the bank angle stays. That is the clue to why we call the aileron a rate control.
Part 1 · Lateral control
Why the roll does not keep speeding up Once rolling, the down-going wing meets air from below: its effective α increases The up-going wing meets air from above: its effective α decreases More lift on the down-going wing opposes the roll: aerodynamic damping The faster the roll, the more damping, until damping balances the aileron moment Result: a given aileron angle gives a steady rate of roll , not a bank angle Rolling right: the two wing sections Down-going (right) wing TAS + upward airflow from the roll α increased Up-going (left) wing TAS + downward airflow from the roll α reduced Down-going wing: more α, more lift: opposes the roll This is aerodynamic damping in roll
Chapter 20 · Roll, Yaw and Trim
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does a fixed aileron deflection give a steady rate of roll, rather than a roll that keeps speeding up? Because of aerodynamic damping. Once the aircraft is rolling, the down-going wing is moving down through the air, so it meets air coming up at it from below as well as from ahead. That increases its effective angle of attack. The up-going wing meets air coming from above, and its effective angle of attack decreases. So the down-going wing gains lift and the up-going wing loses lift, which produces a rolling moment against the roll. The faster the roll, the stronger this damping. The roll accelerates only until the damping moment equals the aileron moment, and then it continues at a steady rate. That is why a given aileron angle gives a rate of roll, not a fixed bank angle, and why the exam calls the aileron a rate control. More aileron means a faster roll rate.
Part 1 · Worked example
Rate of roll: true airspeed and wingspan A Semi-span 15 m · TAS 60 m/s (117 kt) TAS 60 m/s 7.9 m/s vertical scale × 4 for clarity tip speed = 0.524 × 15 = 7.85 m/s Δα at tip = 7.5° roll rate 30°/s = 0.524 rad/s B Same wing · TAS 120 m/s (233 kt) TAS 120 m/s 7.9 m/s vertical scale × 4 for clarity tip speed = 0.524 × 15 = 7.85 m/s Δα at tip = 3.7° roll rate 30°/s = 0.524 rad/s C Semi-span 5 m · TAS 60 m/s TAS 60 m/s 2.6 m/s vertical scale × 4 for clarity tip speed = 0.524 × 5 = 2.62 m/s Δα at tip = 2.5° roll rate 30°/s = 0.524 rad/s Aileron moment depends on IAS ; damping depends on the tip speed ÷ TAS . So at constant IAS, higher TAS (altitude) and a shorter span give a higher roll rate .
Chapter 20 · Roll, Yaw and Trim
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Take a roll rate of thirty degrees per second, which is zero point five two four radians per second. In case A the semi-span is fifteen metres, so the wingtip moves down at zero point five two four times fifteen, about seven point eight five metres per second. At a true airspeed of sixty metres per second, about one hundred and seventeen knots, that adds roughly seven and a half degrees to the tip's angle of attack. In case B the same wing flies at a true airspeed of one hundred and twenty metres per second. The tip speed is the same but the extra angle halves to about three point seven degrees, so damping is weaker and, for the same aileron, the roll rate is higher. That happens at altitude at a constant indicated airspeed. In case C the semi-span is only five metres, so the tip moves at two point six metres per second and the angle is just two and a half degrees. Short wings roll faster.
Part 1 · A side effect
Adverse aileron yaw Ailerons raise lift on one wing and cut it on the other More lift on the up-going wing (down aileron) means more induced drag Less lift on the down-going wing means less induced drag The drag difference yaws the nose away from the roll : roll left, yaw right The tilted lift vectors of the rolling wings add to it; worst at low speed, high C L Rolling left, seen from above more lift, more induced drag less lift, less drag nose yaws RIGHT roll LEFT Yaw opposite to the roll: adverse aileron yaw worst at low speed and high C L
Chapter 20 · Roll, Yaw and Trim
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ailerons have an unwanted side effect. They make a rolling moment by increasing the lift on one wing and reducing it on the other. But induced drag goes with lift. The wing with the down-going aileron, which is the up-going wing, gets more lift and so more induced drag; the other wing gets less lift and less induced drag. That difference in drag pulls the rising wing back and the nose swings away from the direction of roll. Roll to the left, and the nose swings right. This is adverse aileron yaw. There is a second contribution once rolling: the down-going wing has a larger effective angle of attack, so its lift tilts forward, and the up-going wing's lift tilts back, which adds to the adverse yaw. It is worst at low speed, at high lift coefficients, when large aileron angles are needed. Unless it is corrected with rudder, the turn starts with the nose going the wrong way.
Part 1 · Curing adverse yaw
Four cures for adverse yaw Differential ailerons up aileron: 22° down aileron: 10° up travel larger than down Frise ailerons up aileron: nose juts below down aileron: nose shrouded extra drag on the down-going wing Differential ailerons Linkage makes the up aileron travel further than the down one: more drag on the down-going wing.
Frise ailerons Up aileron's nose juts below the wing: extra profile drag on the down-going wing.
Aileron–rudder coupling An interconnect moves the rudder automatically with the ailerons.
Roll spoilers Spoilers rise on the down-going wing , adding drag there: yaw goes with the roll.
Chapter 20 · Roll, Yaw and Trim
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are four standard cures for adverse yaw, and each works by adding drag to the down-going wing, or by using the rudder. With differential ailerons, the linkage makes the up-going aileron move through a larger angle than the down-going one, for example twenty-two degrees up and only ten down. The up aileron makes more profile drag, the down aileron less, so the drag difference between the wings shrinks. Frise ailerons have an asymmetric nose and a hinge set back. When the aileron goes up, its nose juts below the lower surface of the wing into the airflow and makes extra drag on that wing, the down-going one; the nose of the down-going aileron stays shrouded. Aileron-rudder coupling simply interconnects the controls, so the rudder moves automatically to cancel the yaw. And roll spoilers rise on the down-going wing, adding drag there, so the yaw actually goes with the roll. In the exam, the purpose of differential ailerons is to reduce the yawing moment that opposes the turn.
Part 1 · High speed
Aileron reversal A down aileron loads the trailing edge and twists the flexible wing nose-down Tip incidence falls, so the wing loses some of the lift the aileron added The twist grows with IAS ; at the reversal speed the loss equals the gain Beyond it the wing goes down when the pilot wants it up: aileron reversal Most likely with a flexible wing at high speed ; cures: stiffer wing, inboard ailerons , spoilers Down aileron twists a flexible wing aileron load lift lost by twist nose-down twist tip incidence reduced reversal speed stiffer wing or inboard ailerons IAS → 1 0 roll effectiveness
Chapter 20 · Roll, Yaw and Trim
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ailerons are normally out at the wingtips, where they have the longest arm and give the greatest rolling moment. But that also lets them twist the wing hardest. A wing is not rigid. When an aileron goes down, the extra load near the trailing edge twists the wing nose-down and reduces the incidence at the tip. That loss of incidence takes away part of the lift the aileron was meant to add, so the aileron is less effective than it should be. The twisting load grows with indicated airspeed, and eventually there is a speed where the lift lost through twist equals the lift gained from the aileron: the aileron does nothing at all. Faster still, the wing actually goes down when the pilot wanted it up. That is high-speed aileron reversal, and it is most likely with a flexible wing at high speed. Moving the ailerons inboard, where the wing is stiffer, pushes the reversal speed higher, but costs some effectiveness at low speed.
Part 1 · Jet transports
Inboard and outboard ailerons Outboard ailerons : biggest moment, but biggest twist. Used at low speed only Inboard ailerons : on the stiffer inner wing, used at all speeds Outboard ailerons are locked out as the flaps retract Low speed: both sets work. High speed: only the inboard ones respond Spoilers on the upper surface add roll power at all speeds Right wing of a jet, seen from above inboard aileron all speeds outboard aileron low speed only flaps spoilers Flaps out: both sets work Flaps in: outboard ailerons locked out
Chapter 20 · Roll, Yaw and Trim
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Large jets often solve the reversal problem with two sets of ailerons. The outboard ailerons, near the tips, give the biggest rolling moment for a given force, but also the biggest twist, so they are used only at low speed, when the air loads are small. The inboard ailerons sit on the stiffer inner part of the wing, usually between the flaps, and work at all speeds. Watch the scene: on the approach, with the flaps down, both sets of ailerons move. Then, as the flaps retract, the outboard ailerons are locked out and stay faired with the wing. From then on, at high speed, only the inboard ailerons respond to the wheel, helped by the spoilers. So the rule is: at low speed both sets work, and at high speed only the inboard ailerons. That keeps plenty of roll power for slow flight without twisting the wing when the dynamic pressure is high.
Part 1 · Sharing the trailing edge
Drooped ailerons and flaperons Flaps want big trailing-edge span ; so do ailerons. The space is limited Solution 1: droop both ailerons symmetrically with the flaps, adding flap area They then move differentially from the drooped position for roll Solution 2: flaperons : one surface does both jobs Either way, more of the span works for take-off and landing lift Neutral, clean left 0° right 0° Drooped as flaps (both down 15°) left 15° right 15° Roll right from the droop left 25° right 5° Flaperon: the same surface does both jobs
Chapter 20 · Roll, Yaw and Trim
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Flaps and ailerons compete for the same real estate, the wing trailing edge. For good take-off and landing performance the flaps should be as large as possible, and for a good rate of roll the ailerons should be large too. One solution is to droop the ailerons. When the flaps go down, both ailerons also move down symmetrically, adding to the flap area. For roll they then move differentially from that drooped position: one goes further down, the other comes back up. In the example on the screen, both ailerons droop fifteen degrees, and a roll to the right takes the left one to twenty-five degrees and the right one back to five. The other solution is the flaperon, where a single set of trailing-edge surfaces does the work of both flaps and ailerons, moving together as flaps and differentially as ailerons. Either way, more of the span contributes to lift at low speed.
Part 1 · Spoilers
Roll control spoilers Panels on the upper surface , hinged at the front, raised hydraulically They rise on the wing with the up-going aileron (the down-going wing), in proportion to the input On the other wing they stay flush : a mixer sends them up only with an up aileron Roll to port: port spoilers up Spoilers cannot add lift, so a spoiler roll always costs net lift Roll left, seen from behind spoilers up with the up aileron spoilers flush with the down aileron lift lost, drag up Mixer: aileron UP → spoilers rise in proportion Aileron DOWN → spoilers stay flush Drag on the down-going wing: yaw WITH the roll Always a net loss of lift in the roll
Chapter 20 · Roll, Yaw and Trim
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Spoilers can give lateral control in addition to, or instead of, ailerons. They are panels on the upper surface of the wing, hinged at their front edge and raised hydraulically. A raised spoiler disturbs the airflow and kills lift on that part of the wing. For roll, the spoilers rise on the wing with the up-going aileron, which is the wing you want to go down, and they rise in proportion to the control input. On the other wing they stay flush. This is done by a mixer unit, which raises the spoilers when the aileron on that side goes up but leaves them retracted when it goes down. So for a roll to port, the port spoilers go up. On the screen the left wing drops as its spoilers kill the lift. Because a spoiler can only reduce lift, never increase it, a roll made with spoilers always gives a net loss of lift, which the pilot must allow for.
Part 1 · Spoilers and ailerons
Why jets use spoilers for roll Feature Spoiler Why it matters Adverse yaw None : drag rises on the down-going wing, yaw goes with the rollTurns start cleanly Wing twist Less : the load acts further forward than an aileron'sReversal pushed away Transonic flight Not weakened by shock-induced separation Roll power kept at high Mach Flutter Cannot develop flutterNo mass balance needed Trailing edge Leaves it free for flaps Bigger flaps, better field performance Lift Can only reduce lift: net loss in a roll The one drawback
Most jets mix the two: ailerons can be weak at low dynamic pressure and twist the wing at high speed, so spoilers augment them; some aircraft use spoilers only at low speed (inoperative with flaps up).
Chapter 20 · Roll, Yaw and Trim
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Spoilers have several advantages over ailerons, and these appear regularly in the exam. First, there is no adverse yaw: the raised spoiler adds drag on the down-going wing, so the yaw goes in the same direction as the roll. Second, wing twisting is reduced, because the air load on a spoiler acts further forward on the chord than an aileron's, closer to the wing's torsion axis. Third, at transonic speeds a spoiler keeps working, whereas an aileron behind a shock wave can lose effectiveness through shock-induced separation. Fourth, a spoiler cannot develop flutter. And fifth, spoilers do not use the trailing edge, so it can all be given to flaps. The one drawback is that a spoiler can only reduce lift. In practice most jets combine them: ailerons may be too weak at low speed and twist the wing at high speed, so spoilers augment the roll rate, and on some types the spoilers work only at low speed, switched off when the flaps are retracted.
Part 2 · Drag devices
Speed brakes Used to decelerate quickly (for example to rough-air speed) or descend steeply (ATC, emergency descent) Ideal: drag with no lift loss and no pitch change : a fuselage brake comes closest Most jets use the wing spoilers , raised symmetrically by a separate lever Usually cleared to VMO / MMO , but may blow back from full extension at high speed Roll still works: spoilers move asymmetrically from the speed brake position Two kinds of speed brake fuselage brake: drag with no lift or pitch change (ideal) wing spoilers as speed brakes: separate lever, symmetric; costs lift Usually cleared up to VMO / MMO, but may "blow back" from full extension at high speed
Chapter 20 · Roll, Yaw and Trim
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Speed brakes add drag so the aircraft can slow down quickly or descend steeply. You might need to decelerate fast to the rough air speed after meeting turbulence at high speed, or descend steeply to meet air traffic control requirements, or above all in an emergency descent. Ideally a speed brake would give drag with no loss of lift and no change in pitching moment, and a fuselage-mounted brake comes closest to that. But since the wing spoilers already make drag, it is convenient to use them as speed brakes too. They are then controlled by a separate lever and rise symmetrically on both wings. Speed brakes are normally cleared for use up to V M O or M M O, but at high speed they may be blown back from full extension by the air loads. And they still work as roll controls: from the speed brake position the spoilers move asymmetrically, those on the up-aileron wing rising further and those on the other wing moving down towards stowed.
Part 2 · Drag devices
Speed brakes and the drag curve Speed brake drag is profile (parasite) drag The whole drag curve rises, and V M D moves to a lower speed Worked: doubling parasite drag cuts V M D by a factor of 2¼ ≈ 1.19: 220 kt → 185 kt More of the low-speed range is now on the stable side of the drag curve So speed stability at low speed is better with speed brakes out 120 160 200 240 280 320 360 V MD 220 kt V MD 185 kt clean speed brakes out IAS (knots) Total drag (example units) Brakes add profile (parasite) drag only
Chapter 20 · Roll, Yaw and Trim
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The drag from speed brakes is profile drag, in other words part of the parasite drag. Adding parasite drag raises the right-hand side of the drag curve much more than the left, so the total drag goes up and the minimum drag speed, V M D, moves to a lower speed. On the chart, the clean aircraft has its minimum drag at two hundred and twenty knots. With the speed brakes doubling the parasite drag, the minimum moves down by a factor of the fourth root of two, about one point one nine, to roughly one hundred and eighty-five knots. Why does that help? Below V M D an aircraft is speed unstable: if it slows down, drag increases, and it tends to slow down further. With V M D lowered, more of the low-speed range lies on the stable side of the curve. So, with the speed brakes extended, speed stability at low speed is better than in the clean configuration.
Part 2 · On the runway
Ground spoilers: lift dumpers Stopping forces on the landing run: aerodynamic drag , reverse thrust and wheel brakes Brakes depend on the weight on the wheels , which any remaining wing lift reduces Speed brake lever to lift dump : spoilers kill the lift, putting weight on the wheels Both brake drag and aerodynamic drag rise: shorter landing run Extra ground spoilers are locked out in flight by a gear-leg (squat) switch Landing roll: lift dumped onto the wheels lift destroyed weight on wheels more drag squat switch on the gear leg Speed brake lever to LIFT DUMP: extra ground spoilers rise Less lift: more weight on the wheels, brakes work better Plus aerodynamic drag: shorter landing run Disabled in flight by the gear-leg (squat) switch
Chapter 20 · Roll, Yaw and Trim
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
After touchdown, three things slow the aircraft: aerodynamic drag, reverse thrust and the wheel brakes. The wheel brakes can only grip as hard as the weight on the wheels allows, and any lift the wing is still producing takes weight off the wheels. So, on landing, the speed brake lever is moved to the lift dump position. The spoilers rise and destroy most of the wing's lift. That puts the weight firmly on the wheels, so the brakes work better, and the raised panels add aerodynamic drag too. Both effects shorten the landing run. On many aircraft, extra spoiler panels, the ground spoilers, come up in the lift dump selection that never deploy in the air. They are made inoperative in flight by a switch on the undercarriage leg, worked by the leg extending after take-off. In the exam, wing spoilers can be used as air brakes, as lift dumpers and for lateral control, and on landing they reduce lift to make the brakes more effective.
Part 3 · Directional control
The rudder Rudder jobs: asymmetric power , crosswind take-off and landing, adverse yaw , spin recovery , propeller torque changes Rudder left: the aircraft yaws left, creating a sideslip from the right Sideslip on the fixed fin gives a force opposing the rudder Yaw stops when they balance: one rudder angle = one yaw angle Coordinated turn left: left pedal forward , rudder left Left rudder, seen from above rudder force nose yaws left sideslip: air from the right Sideslip on the fin opposes the rudder until balanced one rudder angle = one yaw (sideslip) angle coordinated left turn: left pedal forward, rudder left
Chapter 20 · Roll, Yaw and Trim
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Control in yaw comes from the rudder. It is needed to keep straight with asymmetric power, to correct for crosswinds on take-off and landing, to cancel adverse yaw, to recover from a spin, and on single-engined aircraft to correct for changes in propeller torque. Suppose the rudder is deflected to the left. The aircraft will begin to yaw left, which means the air now meets it from the right: a sideslip. That sideslip acts on the fixed part of the fin and produces a force that opposes the rudder. As the yaw grows, so does this force, until it balances the rudder, and the aircraft stops yawing and holds that yaw angle as long as the rudder is held. Return the rudder to neutral and both fin and rudder push the aircraft back to its original heading. So, like the elevator, a given rudder angle gives a given yaw displacement. For a coordinated turn to the left, the left pedal goes forward and the rudder moves left.
Part 3 · Directional control
Fin stall and the dorsal fin The sideslip angle is the fin's angle of attack, so the fin can stall Rudder applied to correct the sideslip adds camber: it lowers the fin's stalling angle A fin stall means a sudden loss of directional stability Lower aspect ratio stalls at a larger angle A dorsal fin lowers the fin's aspect ratio, raising its stalling angle Fin side force against sideslip angle 0° 10° 20° 30° 40° tall fin: stalls at ≈ 23° dorsal fin: ≈ 38° Sideslip = fin angle of attack dorsal fin
Chapter 20 · Roll, Yaw and Trim
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The fin is an aerofoil standing on its end, and the sideslip angle is effectively its angle of attack. So, like any aerofoil, it has a critical angle at which it stalls, and a stalled fin no longer keeps the aircraft straight. If the rudder is deflected in the direction that corrects the sideslip, it adds camber to the fin in the direction it is already loaded, so the stalling angle is reduced, just as a down aileron reduces the stalling angle of a wing. How can a designer delay fin stall? The stalling angle of an aerofoil depends on its aspect ratio: low aspect ratio surfaces stall at much larger angles. Fitting a dorsal fin, a long, low extension running forward from the base of the fin, reduces the fin's effective aspect ratio. On the chart, the tall fin alone stalls at about twenty-three degrees of sideslip; with a dorsal fin the stall is delayed to well over thirty degrees.
Part 3 · Asymmetric thrust
Engine failure and VMC After an engine failure on a twin, the live engine gives a yawing moment The rudder must balance it, but rudder force ∝ IAS² Below a certain speed, even full rudder is not enough That speed is the minimum control speed, VMC Worked: need 6 000 N, full rudder gives 9 000 N at 150 kt: VMC = 150 × √(6/9) ≈ 122 kt Engine failed: can full rudder hold it? 0 50 100 150 200 0 3 6 9 12 VMC ≈ 122 kt needed to balance the live engine: 6 000 N full rudder: 9 000 N at 150 kt ∝ IAS² not enough rudder IAS (knots) Fin side force (kN)
Chapter 20 · Roll, Yaw and Trim
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a twin-engined aircraft, if one engine fails, the thrust of the other engine acting out on the wing gives a strong yawing moment towards the dead engine. The rudder must counter it. But the force the rudder can make depends on the dynamic pressure, so it varies with the square of the indicated airspeed. That means there is a minimum speed at which full rudder is just enough to balance the engine yawing moment, and below it the aircraft cannot be held straight. That speed is the minimum control speed, V M C. Let us work an example. Suppose the fin must produce six thousand newtons of side force to balance the live engine, and full rudder gives nine thousand newtons at one hundred and fifty knots. Since force goes with speed squared, the speed where full rudder gives six thousand is one hundred and fifty times the square root of six over nine, which is about one hundred and twenty-two knots. Below that, you lose directional control.
Part 3 · High speed
The rudder ratio changer Simple systems: full pedal = full rudder at every speed Large deflections are needed at low speed (engine failure, crosswind) At high speed , full rudder would overload the structure A ratio changer gears down the rudder as speed rises Single gear change above a set speed, or progressive reduction with speedMaximum rudder angle for full pedal 0 100 200 300 400 0° 10° 20° 30° single gear change progressive IAS (knots) progressive: 30 × (160 / IAS)² keeps the rudder load about constant
Chapter 20 · Roll, Yaw and Trim
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a simple control system, full pedal movement always gives full rudder deflection. Large jets need large rudder deflections at low speed, for engine failures near V M C and for crosswind landings. But at high speed, full rudder would put enormous loads on the fin and rear fuselage, because the force rises with the square of the speed. So a gear change, the rudder ratio changer, is built into the rudder control system. It can be a single gear change, which gives a smaller rudder deflection for full pedal movement above a certain speed. In the example, thirty degrees below two hundred and fifty knots and fifteen degrees above. Or it can be progressive, with the maximum rudder deflection falling steadily as speed rises. The blue curve here holds thirty degrees up to one hundred and sixty knots and then reduces with the square of the speed ratio, so the rudder load stays roughly constant, down to about five degrees at four hundred knots.
Part 3 · Coupling
Secondary effects of roll and yaw Yaw → roll : yaw left and the right wing moves faster, gains lift: the aircraft rolls left Roll → yaw : ailerons give adverse yaw ; the rolling wings' α changes add to itRudder → small roll : the fin force acts above the CG : rudder left gives a small roll right A high fin can make that adverse roll noticeable; an aileron–rudder interconnect can cancel it Steady turn: the outer wing is faster and overbanks; hold off with slight opposite aileron Rolling moment due to yaw right wing faster: more lift yaw left → roll left Rudder left, high fin fin force right small roll RIGHT (adverse) Steady turn: the outer wing is faster, so it overbanks. Hold off with a little opposite aileron once the bank is set. Roll left also gives adverse yaw right (lesson part 1).
Chapter 20 · Roll, Yaw and Trim
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each control turns the aircraft about one axis but also gives a moment about another, especially between roll and yaw. Start with yaw. If the aircraft is yawing to the left, the right wing moves forward faster than the left, so it makes more lift, and the aircraft starts rolling to the left. So the secondary effect of yaw is roll in the same direction. Now roll. We have seen that ailerons produce adverse yaw, and once rolling, the changed angles of attack add to it. The rudder has a small side effect too. With left rudder, the side force on the fin acts to the right, and because the fin's centre of pressure is above the centre of gravity, that gives a small rolling moment to the right. It is usually tiny, though a high fin makes it noticeable. Finally, in a steady turn the outer wing is faster and tends to overbank, so you hold off with a little opposite aileron.
Part 4 · Trimming
What trimming does Pitch speed · power · CG Yaw asymmetric power · prop torque Roll asymmetric load or fuel Trimmed = holds its attitude and speed with ZERO force on the controls Trim tab Small tab on the control surface, moved opposite to it by the trim wheel or switch.
Trimming tailplane The whole stabiliser incidence is changed by a screw jack.
Spring bias An adjustable spring in the circuit cancels the stick force. No tab.
CG and feel Move the CG by fuel transfer, or reset the artificial feel datum.
Chapter 20 · Roll, Yaw and Trim
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
An aeroplane is trimmed when it holds its attitude and speed without the pilot having to apply any force to the controls. If a control surface must stay deflected to keep the aircraft in balance, the pilot would have to hold a force on the stick, and trimming reduces that force to zero. In pitch, you need to retrim whenever the speed, the power or the centre of gravity position changes. In yaw, trim is needed on a multi-engined aircraft with asymmetric power, or when propeller torque changes. Roll trim is needed less often, for an asymmetric configuration or a lateral displacement of the centre of gravity, such as unbalanced fuel. The main methods are the trim tab, the variable incidence or trimming tailplane, spring bias, adjustment of the centre of gravity, and adjustment of the artificial feel unit. We take them one at a time.
Part 4 · Trimming
The trim tab A small adjustable surface in the trailing edge of a control surface Set from the cockpit by a trim wheel or switch , working in the instinctive sense Moves opposite to the control surface until tab moment = hinge moment Then f × D = F × d : stick force zero . It slightly reduces the surface's force Fixed tabs : ground-adjustable, on ailerons and rudder, for a permanent out-of-trimNose-heavy aircraft trimmed with a tab F (elevator load, down) f (tab load, up) d D Trimmed when f × D = F × d: stick force zero 144 N m ÷ 0.6 m = 240 N of tab load tab moves opposite to the elevator
Chapter 20 · Roll, Yaw and Trim
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
A trim tab is a small adjustable surface set into the trailing edge of a main control surface. It is moved by a trim wheel or switch, usually in the instinctive sense: wind the top of the wheel back to trim nose up. To hold the main surface where it needs to be, the tab is deflected in the opposite direction until the moment of the tab force about the hinge balances the hinge moment of the control surface. Then the stick force is zero. Take the example on the screen. The elevator is held up with a hinge moment of one hundred and forty-four newton metres. If the tab acts zero point six metres behind the hinge, it needs to make two hundred and forty newtons. Because the tab force opposes the elevator force, trimming slightly reduces the force the surface produces. Some tabs, called fixed tabs, are adjusted only on the ground, usually on ailerons and rudder, to correct a permanent out-of-trim condition.
Part 4 · Worked examples
Which way does the tab go? Rule: decide which way the surface must move; the tab moves the opposite way .
Situation Surface needed Trim action Tab moves Nose heavy, hands off Elevator up Trim wheel top back Elevator tab down Right engine fails (twin) Rudder left Rudder trim to the left Rudder tab right Right wing low; tab on left aileron Left aileron up , right down Roll trim left Left aileron tab down Take-off with elevator locked , nose heavy Elevator cannot move Trim wheel back Tab down: acts as a tiny elevator, more nose heavy
With the elevator locked, the tab cannot move the elevator, so its own force acts directly on the tail: tab down pushes the tail up and the nose further down.
Chapter 20 · Roll, Yaw and Trim
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Use one rule for trim senses: decide which way the surface must move, and the tab goes the opposite way. Nose heavy with hands off? The elevator must go up to raise the nose, so you wind the top of the trim wheel back, and the elevator tab moves down. Right engine failed on a twin? The aircraft yaws right, so the rudder must go left, and to hold it there the rudder trim tab moves right. Right wing low, with a tab only on the left aileron? The left aileron must go up, so its tab moves down, and the linked right aileron goes down. The trap: an aircraft takes off with the elevator lock still in place and is nose heavy. Winding the trim back moves the tab down, but the elevator cannot move, so the tab simply acts like a tiny elevator the wrong way, lifting the tail and making the aircraft even more nose heavy.
Part 4 · Trimming
The variable incidence (trimming) tailplane The trim wheel drives a screw jack that changes the tailplane incidence Trimmed when the tailplane makes the load the elevator used to make: elevator neutral Advantages: less trim drag , full elevator range kept, very powerful for large CG and speed ranges Disadvantage: heavier and more complex than a trim tab Take-off stabiliser setting from the flight manual, for the CG: wrong setting means a tail strike or very heavy rotation Variable incidence (trimming) tailplane Trimmed with the elevator screw jack elevator up 10° incidence fixed Trimmed with the stabiliser screw jack elevator neutral incidence nose down Same tail load, elevator left free for manoeuvre less trim drag · full pitch authority · large trim range but heavier and more complex
Chapter 20 · Roll, Yaw and Trim
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Most jets trim in pitch by moving the whole tailplane, the stabiliser. The trim wheel or switch drives a screw jack at the front of the tailplane, which pivots about a point near its rear spar. You trim by changing the incidence until the tailplane itself produces the load that the elevator was providing, and the stick force falls to zero with the elevator approximately neutral. That brings three advantages: trim drag is lower, because a streamlined tailplane is cleaner than one with a deflected elevator; none of the elevator's travel is used up for trimming, so full pitch control remains; and it is very powerful, coping with a large range of centre of gravity positions and speeds. The disadvantage is weight and complexity. Before take-off, the stabiliser must be set to the value from the flight manual for the actual centre of gravity. Set it wrongly and the aircraft may over-rotate into a tail strike, or need very heavy stick forces to rotate, lengthening the take-off.
Part 4 · Trimming
Forward CG eats nose-up authority With a conventional elevator and tab, trimming uses up elevator travel Forward CG needs more up elevator to trimSo less up travel remains: nose-up pitch authority is reduced Example: 20° available; forward CG trim takes 10°, leaving only 10° Critical for rotation and the flare ; a trimming tailplane avoids it Elevator up travel 20°: what is left after trimming? Aft CG 2° 18° left Mid CG 5° 15° left Forward CG 10° 10° left used by trim available to pitch nose up Forward CG: more up elevator needed to trim so less nose-up authority remains (flare, rotation) a trimming tailplane avoids this
Chapter 20 · Roll, Yaw and Trim
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the main drawback of trimming with a conventional elevator and tab. Whatever elevator deflection is needed to trim is no longer available for manoeuvring. A forward centre of gravity makes the aircraft nose heavy, so more up elevator is needed to trim, and that leaves less up elevator for pitching the nose up. In the example, the elevator has twenty degrees of up travel. At an aft centre of gravity, trimming uses only two degrees, leaving eighteen. At a mid centre of gravity it uses five, leaving fifteen. At the forward limit it uses ten, leaving only ten degrees for rotation on take-off and for the flare, which as we saw last lesson is the most demanding case. So after re-trimming for a forward centre of gravity, nose-up pitch authority is reduced. A trimming tailplane avoids this, because it keeps the elevator near neutral whatever the trim.
Part 4 · Trimming
Other ways to trim Fixed tabs Bent or set on the ground only, usually on ailerons and rudder, to cure a permanent out-of-trim condition. They work like a trim tab.
Spring bias An adjustable spring in the control circuit applies a force that cancels the stick force. No tab is needed.
CG adjustment Using deflected surfaces to trim costs drag . Moving the CG , usually by transferring fuel between nose and tail tanks, cuts the balancing load and its drag, so range increases .
Artificial feel trim With powered controls there is no air load at the stick. The feel unit resists movement, so to trim, its datum is reset until it gives no load.
Chapter 20 · Roll, Yaw and Trim
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are several other ways to trim. Fixed tabs are small tabs that can only be adjusted on the ground. They are usually found on ailerons and rudders, to correct a permanent out-of-trim condition, such as a slight wing heaviness, and they work just like an adjustable trim tab. Spring bias trim uses an adjustable spring in the control circuit to apply a force that cancels the stick force; there is no tab at all. Centre of gravity adjustment is used on some large aircraft. Trimming with deflected surfaces always costs drag. If instead the centre of gravity is moved, usually by pumping fuel between tanks in the nose and the tail, the out-of-balance pitching moment and the balancing tail load are reduced, so the trim drag falls and the cruise range increases. Finally, with powered controls, the artificial feel unit pushes back against any stick movement, so trimming simply means moving the datum of the feel unit until it no longer loads the controls.
Summary
What to take into the exam Roll Aileron = rate control. Damping: down-going wing gains α. Higher TAS and shorter span roll faster.
Adverse yaw Roll left, yaw right (induced drag on the up-going wing). Cures: differential, Frise, coupling, spoilers.
Reversal Flexible wing, high IAS. Inboard ailerons at all speeds, outboard locked out flaps up.
Spoilers Rise with the up aileron. No adverse yaw, less twist, no flutter, work transonic; net lift loss.
Drag devices Speed brakes: profile drag, V M D falls, better low-speed speed stability. Lift dump: weight on wheels.
Yaw Rudder angle = yaw angle. Dorsal fin delays fin stall. VMC: rudder force ∝ IAS². Ratio changer.
Coupling Yaw left: roll left. Rudder left: small roll right (high fin). Outer wing overbanks in a turn.
Trim Tab moves opposite to its surface. Stabiliser trim: less drag, full elevator. Forward CG cuts nose-up authority.
Chapter 20 · Roll, Yaw and Trim
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
The aileron is a rate control: damping from the down-going wing's extra angle of attack balances it, and higher true airspeed or a shorter span gives a faster roll. A roll to the left gives adverse yaw to the right, cured by differential and Frise ailerons, aileron-rudder coupling or roll spoilers. Flexible wings at high speed suffer aileron reversal, so jets use inboard ailerons at all speeds and lock out the outboard ones when the flaps retract. Spoilers rise with the up-going aileron, give no adverse yaw, less twist and no flutter, but always cost lift. Speed brakes lower V M D; lift dumpers put weight on the wheels. Rudder angle gives yaw angle, a dorsal fin delays fin stall, and V M C exists because rudder force goes with speed squared. Yaw causes roll the same way. For trim: the tab moves opposite to its surface, stabiliser trim saves drag and keeps the elevator free, and a forward centre of gravity reduces nose-up authority.