Principles of Flight · Chapter 25
Shock Waves and Critical Mach Number How shock waves form on a wing in subsonic flight, what they do to the air, and how they change lift, drag, the centre of pressure and the controls.
shock wave supersonic M 0.82 free stream still subsonic © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
In the last lesson we saw air speeding up over a wing until, somewhere on the surface, it reaches the speed of sound while the aircraft itself is still subsonic. This lesson is about what happens next. A pocket of supersonic flow appears and ends in a shock wave, a thin line where the pressure, density and temperature jump. We will see how normal and oblique shocks behave, what the critical Mach number is and what lowers it, how the shocks grow and move as the Mach number rises, and why they cause shock stall, wave drag, buffet, centre of pressure shifts and weak controls. We finish with expansion waves and the supersonic aerofoil.
Roadmap
Shock waves: what they are and what they do Normal and oblique what a shock does to the air M crit when the first shock appears Lift, drag, CP shock stall, wave drag, buffet Expansion waves and the supersonic aerofoil 1 · Shock waves The normal shock and its jumps; oblique shocks and how they turn the flow.
2 · Critical Mach The first sonic point: Mcrit , what lowers it, and how shocks grow and move.
3 · Effects Lift, CL max , wave drag , the polar, the CP , shock stall, buffet and controls.
4 · Expansion Expansion waves , the three wave types, and the supersonic aerofoil.
Chapter 25 · Shock Waves and Critical Mach Number
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. First the shock wave itself: what a normal shock does to the air passing through it, and how an oblique shock differs. Second, the critical Mach number, the free stream Mach number at which the first bit of flow on the aircraft reaches the speed of sound, what makes it higher or lower, and how the shocks grow and travel along the wing as the aircraft accelerates towards and beyond Mach one. Third, the effects: on lift and the lift curve, on maximum lift, on drag and the drag polar, on the centre of pressure, and the problems of shock stall, buffet and weak controls. Finally, the opposite of a shock, the expansion wave, a table comparing the three wave types, and a look at the flow round a supersonic aerofoil.
Part 1 · Shock waves
A shock wave below Mach 1 A shock forms wherever supersonic flow is slowed to subsonic If the flow keeps its direction, the shock stands at right angles to it: a normal shock Air accelerated over a wing can reach local M > 1 while the aircraft is still subsonic That pocket of supersonic flow ends in a normal shock standing on the surface So compressibility effects begin before the aircraft reaches Mach 1 free stream M 0.80 local M > 1 air accelerated to supersonic normal shock stands across the flow local M < 1 subsonic underneath behind the shock, pressure waves can travel forward again
Chapter 25 · Shock Waves and Critical Mach Number
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A shock wave does not need an aircraft flying faster than sound. Think of the wind tunnel picture, with the wing still and the air moving. Whenever supersonic air is slowed to subsonic speed without changing direction, a shock wave forms at right angles to the flow, as the boundary between the supersonic and the subsonic regions. We call it a normal shock, normal meaning perpendicular. Now remember that a wing speeds the air up over its upper surface. At a free stream Mach number of about point eight, the local flow over the top can reach Mach one point one or so. That pocket of supersonic air, shown in orange, ends in a normal shock standing on the wing, while the aircraft as a whole is still subsonic. Behind the shock the flow is subsonic again, so pressure waves can travel forward once more. This is why compressibility effects begin well before Mach one.
Properties of a normal shock
What happens to air passing through a normal shock Streamlines pass straight through: no change of direction Speed falls to subsonic : Mach behind ≈ 1 ÷ Mach ahead (M 1.25 → about 0.8) Static pressure, density and temperature all increase , suddenlyTotal pressure (energy) is greatly reduced : this loss is dragLeast energy lost when the flow ahead is only just supersonic normal shock M 1.25 M ≈ 0.81 supersonic subsonic, same direction speed and Mach ↓ to subsonic (≈ 1 ÷ M ahead) static pressure ↑ large rise density ↑ temperature ↑ total pressure (energy) ↓ greatly reduced
Chapter 25 · Shock Waves and Critical Mach Number
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look at what a normal shock does to the air going through it. First, the streamlines pass straight through with no change of direction. Second, the flow is slowed to subsonic speed. A handy rule is that the Mach number behind is roughly the reciprocal of the Mach number in front: at one point two five ahead, about point eight behind. The faster the flow ahead, the bigger the drop. Third, the static pressure, the density and the temperature all rise, and they do so suddenly, across a layer only a fraction of a millimetre thick. Fourth, and very important, the total energy of the flow, its total pressure, is reduced, because some of the energy has been turned into heat. That loss shows up as drag on the aircraft. The energy loss is smallest when the air ahead is only just supersonic, which is one more reason to keep shocks weak.
Normal shock in numbers
The stronger the shock, the bigger the jumps Mach ahead Mach behind ≈ 1 ÷ M rule Pressure × Density × Temperature × Total pressure kept 1.10 0.91 0.91 1.25 1.17 1.06 99.9% 1.25 0.81 0.80 1.66 1.43 1.16 98.7% 1.50 0.70 0.67 2.46 1.86 1.32 93.0% 2.00 0.58 0.50 4.50 2.67 1.69 72.1%
Exact normal-shock values for air (γ = 1.4). Near M 1 the shock is weak and loses almost no energy; at M 2 nearly 28% of the total pressure is lost.
Chapter 25 · Shock Waves and Critical Mach Number
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
These are the exact normal shock values for air, so you can see the sizes involved. With the flow just above Mach one, at one point one, the Mach number behind is about point nine one, the pressure rises by about a quarter, and almost no total pressure is lost. At one point two five, the Mach number behind is about point eight one, very close to the one over M rule, the pressure rises by about two thirds, and about one per cent of the total pressure is lost. At one point five the pressure more than doubles and seven per cent is lost. At Mach two the pressure rises four and a half times, the temperature by two thirds, and nearly twenty eight per cent of the total pressure is gone. So a strong shock is very costly in energy, and that is why designers work so hard to keep the shocks on a transonic wing weak.
Oblique shock waves
Normal in the middle, oblique further out A supersonic, no warning B C normal part: strong, subsonic behind strong oblique: dashed line encloses the subsonic region weak oblique, then a Mach line still supersonic behind, turned free stream M 1.6 An oblique shock lies at an angle to the flow: the air is turned as it passes through and may stay supersonic .
Chapter 25 · Shock Waves and Critical Mach Number
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now a body in a supersonic stream, here at Mach one point six. At A the air is moving supersonically and knows nothing about the body ahead. At B, right in front of the nose, air has piled up and is subsonic, trying to slip round the body. Between them stands the shock. In the centre, where it is perpendicular to the flow, it is a strong normal shock and the air behind is subsonic. Moving away from the centre, the shock is no longer at right angles to the flow but leans back at an oblique angle. Near the centre it is still a strong oblique shock, and the dashed line encloses the subsonic region behind it. Further out, at C, the shock is weak: the air is slowed, but it stays supersonic, and it is turned as it passes through. Further still the effect dies away until the line is no longer a shock at all, just a Mach line.
Oblique shock properties
An oblique shock turns the flow The flow is deflected through the wave, to run parallel to the surface that caused it Speed and Mach number fall , but the flow usually stays supersonic Pressure, density and temperature rise ; the energy loss is smaller than in a normal shock The component of velocity across the wave always becomes subsonic Rule: supersonic to subsonic is always sudden , with a shock oblique shock β ≈ 39° M 2.0 M ≈ 1.64 still supersonic, turned 10° 10° wedge Attached oblique shock on a wedge flow turned parallel to the surface
Chapter 25 · Shock Waves and Critical Mach Number
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is an oblique shock in its simplest form: a supersonic flow at Mach two meeting a ten degree wedge. The shock attaches to the point of the wedge and leans back at about thirty nine degrees. Air crossing it is turned through ten degrees, so that it runs parallel to the wedge surface. Its speed and Mach number fall, here to about one point six four, but it is still supersonic. Its pressure, density and temperature rise, and some energy is lost, though much less than in a normal shock. The neat way to think about it: only the part of the velocity that crosses the wave is slowed, and that part always becomes subsonic; the part along the wave is unchanged. So the summary rule is that a change from supersonic to subsonic flow is always sudden and always through a shock. A normal shock marks that change; an oblique shock deflects the flow and may leave it supersonic.
Part 2 · Critical Mach number
The critical Mach number A wing makes lift by accelerating air over its upper surface At small α the fastest flow is near maximum thickness (MFS 0.84 can give local M 1.05) Mcrit : the free stream Mach number at which the local flow first reaches M 1 It is the highest speed with no supersonic flow anywhere on the aircraft At Mcrit itself there is no shock : a shock needs a supersonic region to end M 0.65 Below M crit fastest local flow M 0.92 M 0.72 At M crit local M just reaches 1: no shock yet M 0.78 Above M crit supersonic region + shock
Chapter 25 · Shock Waves and Critical Mach Number
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
A wing makes lift by accelerating the air over its upper surface, so the fastest air on the aircraft is usually there, close to the point of maximum thickness at small angles of attack. In cruise, a free stream of Mach point eight four might give a local Mach number of one point oh five on the wing. As the aircraft speeds up, that fastest point is the first place to reach the speed of sound. The free stream Mach number at which the local flow just reaches Mach one is the critical Mach number. Put another way, it is the highest speed at which no part of the aircraft has supersonic flow. Watch the scene: below critical, everything is subsonic; at critical, the flow just touches Mach one; beyond it, an orange supersonic region appears and ends in a shock. Note this exam point: at the critical Mach number itself there is no shock wave, because there is not yet any supersonic flow for a shock to end.
What sets the critical Mach number
Thicker, more cambered or higher α: lower M crit Greater thickness/chord : more acceleration, lower Mcrit (15% ≈ M 0.75; 5% ≈ M 0.85) Higher angle of attack (higher CL ): faster, further-forward peak, lower Mcrit So higher weight , load factor or altitude at the same Mach all lower Mcrit A control surface deflected down adds camber and lowers Mcrit Raised by thin sections , sweepback and supercritical sections (lesson 26) 4 6 8 10 12 14 16 18 0.6 0.7 0.8 0.9 thickness / chord (%) critical Mach number CL = 0.3 CL = 0.5 CL = 0.7 5% → M 0.85 15% → M 0.75 Illustrative trend: about 0.01 of Mach lost per 1% of thickness, and more lost as the lift coefficient (angle of attack) rises
Chapter 25 · Shock Waves and Critical Mach Number
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
What decides the critical Mach number? Anything that makes the air speed up more over the wing makes it reach Mach one sooner, and so lowers the critical Mach number. A thicker section accelerates the air more: as a rough guide, a fifteen per cent thick wing might have a critical Mach number of point seven five and a five per cent wing about point eight five. A higher angle of attack, meaning a higher lift coefficient, makes the suction peak stronger and moves it forward, so the critical Mach number falls again, as the three lines show. That links it to flight conditions. A heavier aircraft, a higher load factor in a turn or a gust, or flying higher at the same Mach number, all need a higher lift coefficient, so they all lower the critical Mach number; a low wing loading gives a higher one. Deflecting a control surface downward adds camber and lowers it too. To raise it, designers use thin sections, sweepback and supercritical sections, which are the subject of the next lesson.
Beyond M crit
How the shocks grow and move as Mach rises M 0.75 local M just above 1: small bubble, weak shock M 0.81 upper shock stronger, moving aft M 0.89 lower shock forms; separation behind the upper shock M 0.98 both shocks reach the trailing edge bow wave M 1.4 bow wave ahead; oblique trailing-edge shocks supersonic flow shock wave separated flow Small, constant angle of attack; shapes are schematic.
Chapter 25 · Shock Waves and Critical Mach Number
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Just above the critical Mach number, a small region of supersonic flow appears on the upper surface and ends in a weak shock. As the speed increases, the supersonic region grows and the shock gets stronger and moves aft. A similar thing happens on the lower surface, but later, because the lower surface is usually less curved and accelerates the air less; once the lower shock forms, it moves aft quickly and reaches the trailing edge first. By about Mach point eight nine the upper shock is strong enough to separate the boundary layer behind it. At about Mach one, both shocks have reached the trailing edge and the flow over almost the whole of both surfaces is supersonic. Just above Mach one a new shock appears, the bow wave, standing ahead of the leading edge, and the trailing edge shocks become oblique. Most jet transports cruise at the low end of this range with a small shock on top of the wing.
The bow wave
Above Mach 1: the bow wave Supersonic air cannot turn round a leading edge, so it is slowed by a shock ahead of the wing : the bow wave Behind its central, normal part the air is subsonic and can flow round the nose; further out it is oblique At first it is detached , held off by compressed air; it moves closer as speed rises On a sharp leading edge it finally attaches ; a smaller edge angle attaches at a lower Mach Trailing-edge shocks are now oblique as well M < 1 Round leading edge, just above M 1 bow wave detached: normal near the nose, oblique further out Sharp leading edge, M 1.6 shock attached, oblique (β ≈ 48°) Smaller leading-edge angle → attaches at a lower Mach number
Chapter 25 · Shock Waves and Critical Mach Number
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Once the aircraft passes Mach one, a new shock forms in front of the wing: the bow wave. To get round a leading edge the air would have to turn almost through a right angle, and supersonic air cannot do that in the space available. So it is slowed suddenly by a shock standing just ahead of the leading edge. Near the nose this shock is normal, and behind it the air is subsonic, so it can flow round the leading edge before speeding up again over the surface. Further out above and below, the bow wave becomes oblique. At first it stands detached from the leading edge, held off by a cushion of compressed air. As the speed rises it moves closer, and with a sharp leading edge it eventually attaches to it. The smaller the leading edge angle, the lower the Mach number at which that happens. The shocks at the trailing edge are now oblique too.
Pressure distribution in the transonic range
Why lift and the centre of pressure jump about CP 22% M 0.75 suction ↑ net lift +0.36 LE TE CP 28% M 0.81 suction ↑ net lift +0.48 LE TE CP 11% M 0.89 suction ↑ net lift +0.27 LE TE CP 48% M 0.98 suction ↑ net lift +0.51 LE TE CP 50% M 1.4 suction ↑ net lift +0.15 LE TE upper surface lower surface positive lift negative lift (lower suction stronger) schematic; CP from the centre of each area
Chapter 25 · Shock Waves and Critical Mach Number
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
These pressure plots explain most of what follows. Suction is plotted upwards, the solid line is the upper surface, the dashed line the lower, and the area between them is lift: green where it is positive, red where it is negative. The red marker is the centre of pressure. At Mach point seven five the suction is concentrated near the leading edge, the rear third gives almost no lift, and the centre of pressure is well forward. At point eight one a shock has appeared on top; the suction runs further back before the sudden pressure rise, so the centre of pressure moves aft a little and lift is good. At point eight nine the upper shock has spoilt the rear suction while the lower surface still has strong suction, so the rear of the section gives negative lift and the centre of pressure moves forward again. At point nine eight the shocks are at the trailing edge, suction covers nearly the whole upper surface, lift recovers and the centre of pressure goes well aft. At one point four the two surfaces carry similar pressures, lift falls and the centre of pressure sits near half chord.
Part 3 · Effect on lift
Lift coefficient through the transonic range At a constant α, CL rises through the high subsonic range Why: streamlines start to bend later , near the leading edge, giving stronger suction there Above Mcrit the shock begins to separate the boundary layer and CL falls sharply CL recovers near M 1 as the shocks reach the trailing edge, then falls again Wings with sweep, thin sections and less camber show much smaller swings 0.4 0.6 0.8 1.0 1.2 1.4 0.5 1.0 1.5 free stream Mach number CL at a constant angle of attack (relative) transonic 0.75 0.81 0.89 0.98 1.4 M crit shock stall rises: streamlines turn later, nearer the LE
Chapter 25 · Shock Waves and Critical Mach Number
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Hold the angle of attack constant and increase the Mach number. At low speed the lift coefficient is constant. Through the high subsonic range it rises. The reason is the changing streamline pattern: at low speed the air is warned early and the streamlines start to divide well ahead of the wing, but at high subsonic speed they do not bend until close to the leading edge, so the air accelerates more sharply there and the suction is greater. Beyond the critical Mach number, the shock on the upper surface starts to separate the boundary layer, and above about point eight one the lift coefficient falls steeply. That is the shock stall. It recovers near Mach one when the shocks reach the trailing edge and stop causing separation, then falls again in supersonic flow. In the exam, the standard answer is that just above the critical Mach number the lift coefficient starts to decrease. Wings designed for high speed, with sweep, thin sections and little camber, show much smaller swings.
Shock stall
Shock stall: separation behind the shock Across the shock the pressure rises suddenly : a severe adverse pressure gradient The boundary layer thickens and separates behind the shock Lift is lost just as in a low-speed stall: hence shock stall The turbulent wake can buffet and damage the airframe, especially the tail Severity depends on the section; high-speed wings are designed to keep it small shock boundary layer separates behind the shock Sudden pressure rise at the shock → thick, separated boundary layer → loss of lift (shock stall), drag rise, buffet on the tail Thin, swept, low-camber wings suffer far less
Chapter 25 · Shock Waves and Critical Mach Number
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many of the bad effects of shocks come from one mechanism: shock induced separation. As the air passes through the shock, its pressure rises suddenly. For the slow air in the boundary layer, that is a very steep adverse pressure gradient, so the boundary layer thickens and often separates behind the shock, leaving a deep turbulent wake. Because the result is a separated boundary layer and a loss of lift, just as in a low speed stall, it is called the shock stall. Watch the flow behind the shock break away. The wake is not just a loss of lift; it shakes the aircraft, and the turbulent air streaming back can buffet and even damage the tail. How severe it is depends on the shape of the section. A wing not designed for high speed can lose a lot of lift above the critical Mach number, while thin, swept, lightly cambered wings lose much less.
Lift curve and C L max
Steeper lift curve, but a lower CL MAX From about M 0.4 into the transonic range the lift curve gets steeper : more CL per degree But earlier, shock-induced separation lowers CL MAX and the stalling angle CL MAX starts to fall above about M 0.4 At altitude, the stall happens at a higher Mach number, so the stalling speed rises This links straight into the buffet boundaries in lesson 26 0 4 8 12 16 0.0 0.5 1.0 1.5 angle of attack (°) CL low Mach high subsonic steeper slope, lower CL MAX , earlier stall 0.0 0.4 0.8 1.2 0.5 1.0 Mach number CL MAX (relative) falls above about M 0.4
Chapter 25 · Shock Waves and Critical Mach Number
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The same effects change the lift curve. From about Mach point four into the low transonic range, each degree of angle of attack gives more lift than at low speed, so the lift curve is steeper. But the shock induced separation that we just met starts at a lower angle of attack, so the maximum lift coefficient and the stalling angle are both reduced. The lower graph shows the maximum lift coefficient roughly constant up to about Mach point four and then falling steadily towards Mach one. This has a direct practical consequence. High up, the stalling speed in true airspeed terms is a high Mach number, so the lower maximum lift coefficient means a higher stalling speed. That is why stall speed rises at high altitude, and it is the starting point for the buffet boundaries and the coffin corner in the next lesson.
Effect on drag
Wave drag and the transonic drag rise Above Mcrit , drag rises much faster than it would without shocks: the extra is wave drag Energy drag : the irreversible loss across shocks, turned into heatSeparation drag : the turbulent wake behind the shockThe hump from about M 0.89 to 1.2: trailing-edge shocks, separation and the bow wave CD falls again once the shocks reach the trailing edge and separation reduces 0.4 0.6 0.8 1.0 1.2 1.4 1 2 3 free stream Mach number CD at a constant angle of attack (relative) without shocks 0.75 0.81 0.89 0.98 the hump wave drag = energy drag + separation M crit
Chapter 25 · Shock Waves and Critical Mach Number
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Once shocks form, drag rises much more quickly than it otherwise would. The extra is called wave drag, and it has two parts. Energy drag comes from the shocks themselves. Crossing a shock is irreversible: energy goes into raising the temperature of the air, and that lost energy is drag on the aircraft. More oblique shocks absorb less energy each, but as the Mach number rises they spread further sideways and affect more air, so the energy drag keeps rising. Separation drag is the energy lost in the turbulent wake behind the shock. The graph shows the result: flat to the critical Mach number, then a steep rise through point eight one and point eight nine to a peak near Mach one. The hump between about point eight nine and one point two comes from the trailing edge shocks, the separation and, above Mach one, the bow wave. As the shocks reach the trailing edge, separation reduces and the drag coefficient falls back somewhat.
The drag polar
At high Mach the best L/D falls At low speed one CL –CD polar fits all speeds In the transonic range the polar moves : more drag at every CL Drag rises steeply at higher CL as shocks strengthen The tangent from the origin touches at (L/D)max , which is reduced Hence jets cruise just below the drag rise 0.00 0.02 0.04 0.06 0.08 0.00 0.25 0.50 0.75 1.00 CD CL low Mach: L/D max ≈ 18 high Mach: L/D max ≈ 13
Chapter 25 · Shock Waves and Critical Mach Number
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
At low speeds, the curve of lift coefficient against drag coefficient, the drag polar, is the same at every speed. In the transonic range it is not. The polar moves to the right, because every lift coefficient now costs more drag, and at higher lift coefficients the drag climbs steeply as the shocks get stronger. Remember that a straight line from the origin that just touches the polar picks out the best lift to drag ratio. For the low Mach polar here the tangent gives about eighteen, while for the high Mach polar it gives about thirteen. So in the transonic range the maximum lift to drag ratio is reduced, and fuel burn rises. That is why jet transports cruise just below the steep part of the drag rise, accepting a small shock on the wing but not a strong one.
Effect on the centre of pressure
The centre of pressure moves aft, irregularly Above Mcrit upper-surface suction continues back to the shock: more lift from the rear So the CP moves aft , but irregularly , because the lower surface changes too The lower shock forms later but reaches the trailing edge first Overall the CP moves aft to about 50% chord in supersonic flow On a real wing the root (thicker) shocks first: the CP moves towards the tip , and aft on a swept wing 0 25 50 75 100 0.75 0.8 0.9 1 1.2 1.4 centre of pressure (% chord) free stream Mach number 22% 28% 11% 48% 50% supersonic: about 50% ≈ M crit
Chapter 25 · Shock Waves and Critical Mach Number
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The centre of pressure is set by the pressure distribution, so as that changes through the transonic range, the centre of pressure moves. Above the critical Mach number the upper surface pressure keeps falling until the shock, so more of the suction comes from further back, and the centre of pressure moves aft. The movement is irregular, because the lower surface is changing too: its shock forms at a higher Mach number than the upper one but reaches the trailing edge first. The graph, worked out from the pressure plots you saw earlier, shows the centre of pressure moving aft, jumping forward around point eight nine, and moving aft again; overall it ends up at about half chord in supersonic flow. On a real wing there is a spanwise effect as well. The root is usually thicker, so it has a lower critical Mach number and shocks first; lift is lost inboard, the centre of pressure moves towards the tip, and on a swept wing that also means aft. That is the root of Mach tuck, in the next lesson.
Effect on the controls
Shocks make trailing-edge controls weak A control works by changing camber ; deflecting it down lowers Mcrit A shock ahead of the control can separate the flow over it: less effective At low speed a control changes the pressure over the whole section; it cannot change the flow ahead of a shock A shock near the hinge can move back and forth over it: control buzz Remedies: slab tailplane, roll spoilers, vortex generators, Mach-sensitive feel (lesson 26) hinge control down ahead of the shock: control cannot change the flow here shock separated flow over the control a shock near the hinge can oscillate over it: control buzz
Chapter 25 · Shock Waves and Critical Mach Number
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Shocks also weaken the flying controls. A conventional trailing edge control works by changing the camber of the section. Deflecting it downward adds camber, which lowers the critical Mach number, so at high subsonic speed a shock can form ahead of the control, and the separated flow behind that shock passes over the control surface and makes it much less effective. There is a second, subtler problem. At low speed, moving a control changes the pressure distribution over the whole section, all the way to the leading edge. But pressure waves cannot travel upstream through a shock, so with a shock ahead of the hinge, the control cannot affect any of the section in front of the shock. Its effectiveness drops again. Finally, if the shock sits near the hinge, a small control movement can make it jump back and forth over the hinge, causing rapid changes of hinge moment that set up an oscillation called control buzz. The remedies come in the next lesson.
High-speed buffet
Shock-induced buffet Shock-induced separation shakes the airframe: high-speed buffet Cause: air detached by the shock and the turbulent wake striking the tail Low-speed buffet is a useful stall warning; at high speed the dynamic pressure is high So high-speed buffet can cause severe structural damage : it must be completely avoided Crews keep a specified buffet margin using the buffet onset chart tail buffets shock separated, turbulent wake wing section, tailplane and fin seen from the side High dynamic pressure: buffet loads can damage the structure
Chapter 25 · Shock Waves and Critical Mach Number
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Just as separated flow before a low speed stall shakes the aircraft, the separated flow behind a shock at high speed causes buffeting. The air is detached from the wing by the shock, and the turbulent wake streams back and strikes the tailplane, which vibrates and transmits the shaking to the whole airframe. At low speed, buffet is a valuable warning that the stall is near. At high speed it is a danger in its own right. The dynamic pressure in the transonic range is very high, so buffet loads can be large enough to cause severe structural damage, especially to the tail. High speed buffet must therefore be avoided completely, and aircraft are operated so that there is always a margin before buffet would begin. That margin, and the buffet onset chart used to keep it, are covered in the next lesson.
Part 4 · Expansion waves
Expansion waves: the opposite of a shock At a convex corner , subsonic flow faces a steep adverse gradient and separates Supersonic flow turns the corner by expanding through a fan of expansion waves Velocity and Mach number increase ; the flow turns to follow the surface Static pressure, density and temperature decrease The change is gradual: not a shock , and no energy is lost Subsonic flow at a convex corner steep adverse pressure gradient: separates separated Supersonic: M 2.0 → M 2.38 turns 10° through an expansion fan expansion waves speed ↑, Mach ↑; p, ρ, T ↓; no energy lost
Chapter 25 · Shock Waves and Critical Mach Number
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
A shock is one way for supersonic flow to turn a corner: it slows down, and that wastes energy. There is another way. First picture subsonic flow along a surface that suddenly turns away from it, a convex corner. The pressure gradient round the corner would be so steep that the flow would separate right there. Supersonic flow behaves differently. It can follow a convex corner by expanding through a fan of expansion waves spreading out from the corner. In the example, air at Mach two turning through ten degrees speeds up to about Mach two point three eight. Through an expansion wave the velocity and Mach number increase, the flow turns to follow the surface, and the static pressure, density and temperature all decrease, exactly the opposite of a shock. And because the change is gradual rather than sudden, an expansion wave is not a shock, and no energy is lost.
The supersonic aerofoil
Shocks, expansions and a centre of pressure at half chord free stream M 2.0 oblique bow shock attached to a sharp edge expansion fan trailing-edge shocks M 1.79 M 2.22 CP ≈ 50% chord Front faces: high pressure (blue). Rear faces: low pressure. The difference acts rearwards: wave drag even at zero lift. In supersonic flow there is no upwash ahead; lift comes from both surfaces, and the CP is at about 50% chord .
Chapter 25 · Shock Waves and Critical Mach Number
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Put the pieces together on a supersonic aerofoil, here a sharp diamond section at Mach two. At the sharp leading edge, attached oblique shocks turn the air to follow the front faces; the air slows a little, to about one point eight, and its pressure rises, shown in blue. At the shoulders, fans of expansion waves turn the air to follow the rear faces; it speeds up to about two point three, and its pressure falls below the free stream. At the trailing edge, oblique shocks turn the flow back into line. Notice that the front faces carry high pressure and the rear faces low pressure, so even at zero lift there is a net rearward force: that is wave drag. At a small angle of attack the lift comes from both surfaces, the upper surface suction and the lower surface pressure, and the centre of pressure sits at about half chord, well behind the quarter chord position you know from subsonic flow.
The three wave forms
Oblique shock, normal shock and expansion wave Oblique shock Normal shock Expansion wave What it is A sudden change, inclined to the flow A sudden change, at right angles to the flow A gradual change (a fan of waves) Flow direction Turned into the preceding flow No change Turned away from the preceding flow Velocity and Mach behind Decreased, but still supersonic Decreased to subsonic Increased , more supersonicStatic pressure and density Increase Great increaseDecrease Temperature Increase Increase Decrease Energy (total pressure) Decrease Great decreaseNo change (no shock)
Chapter 25 · Shock Waves and Critical Mach Number
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the three wave forms side by side, a favourite source of exam questions. An oblique shock is a sudden change inclined to the flow. It turns the flow into the surface that caused it, slows it but usually leaves it supersonic, increases the pressure, density and temperature, and reduces the energy. A normal shock is a sudden change at right angles to the flow. It does not change the flow direction, slows the flow to subsonic, gives a great increase in pressure and density, increases the temperature and causes a great loss of energy. An expansion wave is a gradual change. It turns the flow away, increases the velocity and Mach number, decreases the pressure, density and temperature, and causes no loss of energy at all. If you remember that an expansion is the exact opposite of a shock, you can rebuild the whole table.
Summary
What to take into the exam Normal shock Supersonic → subsonic , no change of direction. p, ρ, T up ; energy down . M behind ≈ 1/M ahead.
Oblique shock Flow turned , slowed but usually still supersonic ; p, ρ, T up; smaller energy loss.
M crit Free stream M when local flow first reaches M 1 ; no shock yet. Lowered by thickness, α, camber, weight, g.
Development Upper shock first, moves aft; lower shock later, reaches TE first; both at TE near M 1; then bow wave .
Lift and stall CL rises, then shock stall above Mcrit . Steeper lift curve, lower CL MAX above M 0.4.
Drag Wave drag = energy loss + separation. Hump from about M 0.89 to 1.2. (L/D)max reduced.
CP and controls CP moves aft (irregularly) to 50% . Controls lose effect behind a shock; buzz near the hinge.
Expansion Velocity up ; p, ρ, T down ; no energy loss . Buffet: separated wake on the tail; avoid it.
Chapter 25 · Shock Waves and Critical Mach Number
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. A normal shock turns supersonic flow subsonic without changing its direction; pressure, density and temperature rise, energy falls, and the Mach number behind is about one over the Mach number ahead. An oblique shock turns the flow and usually leaves it supersonic, with a smaller energy loss. The critical Mach number is the free stream Mach number at which the local flow first reaches Mach one; there is no shock at that point, and it is lowered by thickness, angle of attack, camber, weight and load factor. The upper shock forms first and moves aft, the lower one forms later but reaches the trailing edge first, and above Mach one comes the bow wave. Lift rises, then shock stall; the lift curve steepens but maximum lift falls. Wave drag is energy loss plus separation. The centre of pressure moves aft, irregularly, to half chord; controls weaken and may buzz; buffet must be avoided. And expansion waves speed the flow up with no energy loss.