Principles of Flight · Chapter 12
Spins and Special Stalls Autorotation and the spin, its phases, the effect of mass and CG, spin recovery, crossed-control, accelerated and secondary stalls, stall recovery in large and small aircraft, high-speed buffet, and stalls caused by ice and heavy rain.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the last of our three lessons on stalling. Here we follow a stall that goes wrong. If one wing stalls more than the other, the aircraft can roll and yaw into a spin, a stable, self-sustaining rotation called autorotation, and recovering takes the right control inputs in the right order. We will look at how a spin starts, its phases, how mass and the centre of gravity change it, and the general recovery. Then we meet the special stalls: crossed-control, accelerated and secondary stalls, power-on stalls in propeller aircraft, and the shock stall at high speed. Finally, we see how ice, frost, snow and heavy rain raise the stall speed, and how an iced tailplane can stall.
Lesson map
When the stall goes wrong 1 · The spin Autorotation, causes, phases, mass and CG, flat spins.
2 · Spin recovery The general recovery for an erect spin, step by step, and why.
3 · Special stalls Crossed-control, accelerated, secondary, power-on and turning stalls; shock stall.
4 · Contamination Ice, frost, snow, icing-induced stalls, tailplane stall and heavy rain.
Chapter 12 · Spins and Special Stalls
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson is in four parts. First, the spin: what it is, why it keeps going by itself through autorotation, what causes it, the phases it goes through, and how the aircraft’s mass and centre of gravity change it, including the dangerous flat spin. Second, the general spin recovery procedure, step by step, with the reason behind each step. Third, the special stalls: the crossed-control stall, the accelerated stall, the secondary stall, the correct stall recovery in jet, multi-engine and single-engine propeller aircraft, stalls in climbing turns, and the shock stall at high speed. Fourth, contamination: how ice, frost and snow raise the stall speed, how an icing-induced stall can creep up without warning, how an iced tailplane can stall, and what heavy rain does. Throughout, remember the one rule for any stall: reduce the angle of attack first.
Part 1 · The spin
What a spin is A steep helical descent about a vertical spin axis The angle of attack of both wings is well above the stall , one more than the other A high rate of rotation ; from above, a circle of radius usually less than the semi-span May be erect or inverted Definition: an aggravated stall resulting in autorotation , a stable rotation that continues by itself vertical spin axis Side view From above radius < semi-span • steep helix, vertical axis • both wings past the stall • high rate of rotation • erect or inverted
Chapter 12 · Spins and Special Stalls
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
When an aircraft is stalled, accidentally or on purpose, the motion can sometimes develop into a spin. Its important features are these. The aircraft descends along a steep helical path about a vertical spin axis. The angle of attack of both wings is well above the stalling angle, though one wing is more stalled than the other. The aircraft rotates rapidly about the spin axis, and if you could look down from above you would see it moving round a small circle whose radius is usually less than the semi-span of the wing. And the spin may be erect, the normal way up, or inverted. The spin is one of the most complex of all flight manoeuvres. The best definition is an aggravated stall resulting in autorotation: the rotation is stable and, if nothing intervenes, the aerodynamic forces themselves keep it going. Throughout the spin, the wings remain unequally stalled.
Part 1 · Autorotation
Autorotation: why the spin keeps itself going 0 10 20 30 40 0 0.4 0.8 1.2 1.6 angle of attack α (degrees) CL up-going wing down-going wing both stalled down-going wing: LESS lift → keeps rolling 0 10 20 30 40 0 0.4 0.8 1.2 angle of attack α (degrees) CD down-going wing: MORE drag → yaws towards the low wing Beyond the stall the lift curve slopes downward : the wing at the larger α has less lift and more drag . So the roll and the yaw both feed themselves .
Chapter 12 · Spins and Special Stalls
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the heart of the spin, autorotation. Below the stall, if a wing goes down its angle of attack increases and it makes more lift, which opposes the roll: that is damping. Beyond the stall the lift curve slopes downward, so everything reverses. In a spin both wings are past the critical angle. On these computed curves the up-going wing is at about twenty degrees and the down-going wing at about twenty-eight. The down-going wing, at the larger angle, has less lift than the up-going wing, so instead of resisting the roll, the lift difference keeps it going. And look at the drag curve: the down-going wing has much more drag, which pulls it back and yaws the aircraft towards the low wing. Roll and yaw both feed themselves. That is why the rotation is stable and continues until the pilot breaks the cycle. Remember for the exam: in a developed spin, the angle of attack of both wings is positive.
Part 1 · Autorotation
How the roll changes each wing’s angle of attack If one wing loses more lift near the critical angle, it drops The down-going wing meets air coming up at it : its relative airflow tilts upward, so its effective α increases The up-going wing has its α reduced , and stays less stalled Yaw towards the low wing speeds up the outer wing and slows the inner one The nose drops; inertia takes over and the spin stabilises at a steady rate Why the roll feeds itself Down-going wing speed roll α larger → stalls deeper Up-going wing speed roll α smaller → less stalled The down-going wing meets air coming up at it: its relative airflow tilts upward and its α rises Yaw towards the low wing slows it further
Chapter 12 · Spins and Special Stalls
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us see how the rotation starts. Suppose the aircraft is near the critical angle and one wing loses more lift than the other: that wing drops. As it moves down, it meets air coming up at it, so its relative airflow is inclined upwards. Look at the left-hand triangle: forward speed plus the downward roll velocity gives a relative airflow coming from further below, so the effective angle of attack of the down-going wing increases, and it stalls more deeply. On the right, the up-going wing moves away from the air, its relative airflow comes from higher up, its angle of attack is reduced, and it stays less stalled. The imbalance grows as the aircraft yaws towards the low wing, which speeds up the high, outside wing and slows the low, inside one. As in any stall the nose drops, and as inertia forces build up, the spin usually settles at a steady rate of rotation and descent.
Part 1 · Causes
What causes a spin A stall must occur before a spin can take place. Then one wing must stall more than the other:
Crossed controls Exceeding the critical α with too much or too little rudder for the aileron in use. If recovery is not prompt, the stall becomes a spin.
Distraction Co-ordination slips when attention is divided: avoiding traffic, clearing obstacles, problems inside or outside the flight deck.
Other imbalances Yaw from an engine failure on a multi-engine aircraft, or a laterally displaced CG from an unbalanced fuel load.
Chapter 12 · Spins and Special Stalls
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
A stall must happen before a spin can take place, and then one wing must stall more than the other. The wing that is more stalled drops, and the nose yaws towards it. The classic cause of an accidental spin is exceeding the critical angle of attack while using either too much or not enough rudder for the amount of aileron, which we call crossed controls. If the correct stall recovery is not started promptly, the stall can develop into a spin. Co-ordinated use of the controls is especially important at low airspeed and high angle of attack. Most pilots fly balanced in routine manoeuvres, but the skill tends to slip when attention is divided: avoiding other aircraft, clearing obstacles on take-off or approach, or dealing with a problem inside the flight deck. Finally, a spin can come from other imbalances, such as the yaw from an engine failure on a multi-engine aircraft, or a centre of gravity displaced sideways by unbalanced fuel.
Part 1 · Phases
The three phases of a spin Stall and wing drop 1 · Incipient spin 2 · Fully developed 3 · Recovery stall, one wing drops rotation builds, rates still changing rotation, airspeed and descent rate steady anti-spin forces win, rotation stops, dive out Start recovery as early as possible : from the incipient phase it takes less height and time; some aircraft will not easily recover from a fully developed spin.
Chapter 12 · Spins and Special Stalls
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
A spin has three phases. The incipient spin is the first: it lasts from the moment the aircraft stalls and rotation begins until the spin is fully developed, and during it the rates are still changing. The fully developed spin exists once the rate of rotation, the airspeed and the vertical rate of descent are steady from one turn to the next. The third phase, recovery, begins when the anti-spin forces, from the pilot’s control inputs, overcome the pro-spin forces. It is vitally important to begin recovery from an unintended spin as soon as possible. Recovering from an incipient spin normally needs less height and time than from a fully developed one; many aeroplanes will not easily recover from a fully developed spin, and others carry on for several turns before the recovery inputs take effect. Every aeroplane spins differently, and the same aeroplane behaves differently with configuration and loading.
Part 1 · Mass and balance
Mass and CG change the spin Higher mass : slower initial rotation, but the rate may increase; more angular momentum , so more time and height to recoverCG forward : more stable, heavier control forces, less likely to make big abrupt inputs; higher stall speedCG aft : less stability, lighter pitch forces, easier to stall ; the spin is flatter CG beyond the aft limit , or power not reduced: the spin may go flat CG forward steep spin, easier recovery CG aft flatter spin attitude CG beyond aft limit flat spin: may be unrecoverable blue: relative airflow from below in the spin
Chapter 12 · Spins and Special Stalls
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Both the mass of the aircraft and how it is distributed affect the spin. A heavier aircraft usually starts to rotate more slowly, but the spin rate may increase as the spin goes on, and its greater angular momentum means more time and more height are needed to stop it. The position of the centre of gravity matters even more, affecting how readily the aircraft spins and every phase of the spin. With the CG towards the forward limit the aircraft is more stable, and the higher control forces make large, abrupt inputs less likely; trimmed, it tends to return to level flight if the controls are released, though its stall speed is higher. With the CG towards the aft limit, longitudinal stability and pitch forces are reduced, so it is easier to stall, and once spinning the further aft the CG, the flatter the spin attitude. With the CG outside the aft limit, or if power is not taken off promptly, the spin is more likely to go flat.
Part 1 · The flat spin
The flat spin Nearly level pitch and roll attitude, spin axis near the CG Less height per turn, but a yaw rate often over 400° per second gives a high descent rate Relative airflow almost straight up : wings held at very high α Upward flow over the tail can make elevator and rudder ineffective Recovery may be impossible relative airflow almost straight up yaw rate can exceed 400°/s tail blanked: rudder and elevator may not work Less height per turn, but a high rate of descent
Chapter 12 · Spins and Special Stalls
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The flat spin is the one to fear. The aircraft rotates with its pitch and roll attitudes nearly level, about a spin axis close to the centre of gravity. Because it is so flat it may lose a little less height in each turn than a normal spin, but the rate of yaw is extreme, often more than four hundred degrees per second, so the overall rate of descent is high. With the aircraft dropping almost vertically in a nearly level attitude, the relative airflow comes almost straight up from below, which holds the wings at a very high angle of attack. Worse, that upward flow over the tail may make both the elevator and the rudder ineffective, and without them the pilot has no way to stop the rotation or lower the nose. Recovery may then be impossible. That is why the aft limit of the centre of gravity must be respected, and why power must be closed promptly when a spin develops.
Part 2 · Spin recovery
General recovery from an erect spin Step Action Why 1 Throttle(s) to idle Less height lost, less chance of a flat spin, no asymmetric thrust; torque and gyroscopic effects can aggravate the spin 2 Neutralise the ailerons Aileron often contributes to flat spins or faster rotation 3 Full rudder against the spin Stops the yaw. Direction from the turn co-ordinator , not the ball 4 Elevator control briskly to about neutral Unstalls the wing; some types need only relaxed back pressure, others full forward 5 Hold until rotation stopsRecovery may take several turns 6 As rotation stops, neutralise the rudder Held rudder can start a spin the other way 7 Recover from the dive with gradual back pressure Too hard: secondary stall or over-g; too slow: overspeed
Steps 1–4 can be done together. Always follow the Flight Manual : there is no universal spin recovery for all aeroplanes.
Chapter 12 · Spins and Special Stalls
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Recovery from a simple stall only needs the angle of attack reduced; a spin recovery must also stop the rotation. Spin aerodynamics are so complex that no single procedure works for every aeroplane, so always follow the Flight Manual. This is the general recovery for an erect spin. One: throttles to idle, which reduces height loss and the chance of a flat spin, removes any asymmetric thrust, and removes engine torque and gyroscopic effects that can aggravate the spin. Two: neutralise the ailerons, because aileron often makes spins flatter or faster. Three: full rudder against the spin, judging the direction from the turn co-ordinator, not the ball. Four: move the elevator control briskly to about neutral. These four can be done together. Five: hold them until the rotation stops. Six: as it stops, neutralise the rudder, or you may spin the other way. Seven: recover from the dive with gradual back pressure, adding power as normal flight resumes.
Part 2 · Spin recovery
The control positions in a recovery Spin direction from the turn co-ordinator ; the ball is unreliable and depends on where it is mounted Spin to the left: full right rudder , ailerons neutral , elevator forward to about neutral Some types need only relaxed back pressure , others full forward travel Rudder neutral as rotation stops Gentle pull-out: closing the throttle also stops speed building up in a clean aircraft vertical spin axis Side view From above radius < semi-span • steep helix, vertical axis • both wings past the stall • high rate of rotation • erect or inverted
Chapter 12 · Spins and Special Stalls
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us picture the inputs for a spin to the left. First establish the direction from the turn co-ordinator. Do not use the ball in the slip indicator: in a spin its indication is not reliable and depends on where in the flight deck it is mounted. With the throttle closed and the ailerons neutral, apply full right rudder, against the spin, then move the control column briskly forward to about the neutral position. Some aircraft need only a relaxation of back pressure; others need the column fully forward. Hold these positions until the rotation stops, which may take more than one turn. As soon as it stops, centralise the rudder, and ease out of the dive with gradual back pressure. Pull too hard and you risk a secondary stall or exceeding the limit load factor; pull too gently and a clean aircraft may exceed its airspeed limits. Keeping the throttle closed during recovery helps prevent that speed build-up.
Part 3 · Special stalls
The crossed-control stall High α with rudder opposite to aileron, or too much rudder in the same direction Shown by the slip indicator ball out of the middle Little or no warning; one wing stalls long before the other : a violent wing drop Resist the instinct to stop the wing drop with aileron Use rudder to stay balanced: ball in the middle , especially at low speed and high α Skidding turn: too much rudder inside wing slower, higher α: stalls first outside wing faster ball out of the middle Do not pick the wing up with aileron: use rudder, ball in the middle
Chapter 12 · Spins and Special Stalls
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The crossed-control stall happens when an aircraft is flown at a high angle of attack with rudder applied the opposite way to the aileron, or with too much rudder in the same direction as the aileron. Either way the aircraft is out of balance, and the ball in the slip indicator is displaced from the middle. Picture a turn onto final approach with too much rudder to tighten it, and opposite aileron to stop the bank increasing. The inside wing is moving more slowly, and with its aileron down its angle of attack is higher, so it reaches the critical angle long before the outside wing. A crossed-control stall can come with little or no warning, and the wing drop can be violent, the first step into a spin. The instinctive reaction, trying to stop the wing drop with aileron, must be resisted, because it only raises that wing’s angle of attack further. Keep the aircraft balanced with rudder, ball in the middle, at all times.
Part 3 · Special stalls
The accelerated stall Caused by abrupt or excessive control movement Steep turns, sudden changes of flight path, a rapid pull-out from a dive Called “accelerated” because it happens at a load factor above 1g Stall speed = VS1g × √n: at 3 g, 60 kt becomes 104 kt Usually more violent than a 1g stall, and unexpected because the speed is high 1 2 3 4 40 60 80 100 120 140 load factor n (g) airspeed (kt) stalled VS = 60 × √n 3 g: 104 kt pull-out at 100 kt, 3 g → stalls 1 g: 60 kt Accelerated stall: n > 1, at a surprisingly high speed
Chapter 12 · Spins and Special Stalls
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
An accelerated stall is caused by an abrupt or excessive control movement: a sudden change of flight path, a steep turn, or a rapid pull-out from a dive. It is called accelerated because it happens at a load factor greater than one g. We already know that stall speed rises with the square root of the load factor. Take a light aircraft with a one g stall speed of sixty knots. At three g its stall speed is sixty times root three, about one hundred and four knots. So if the pilot snatches the stick back to pull out of a dive at one hundred knots and the load factor reaches three g, the wing stalls, at a speed well above anything the pilot associates with stalling. That is the danger: an accelerated stall is usually more violent than a one g stall, often with a sharp wing drop, and it is unexpected because the airspeed looks safe.
Part 3 · Special stalls
The secondary stall A second stall during the recovery from the first Caused by hurrying: not reducing α enough at the stall warning Or not allowing time for the aircraft to fly again before trying to regain height Correct: full power, relax the back pressure , let the aircraft fly Then moderate back pressure to recover the lost height height time → stall pulls too soon secondary stall: more height lost let it fly, then moderate back pressure Keep full power, relax the back pressure, let the aircraft fly, then gently regain the lost height
Chapter 12 · Spins and Special Stalls
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
A secondary stall is a second stall triggered while recovering from the first. It usually happens because the pilot tries to hurry the recovery, in one of two ways: by not reducing the angle of attack enough when the stall warning comes, or by not giving the aircraft enough time to start flying again before trying to regain the height that was lost. In the graph, the green line is the correct recovery: the nose comes down, speed builds, and then a moderate pull brings the aircraft back to level flight. The red dashed line shows the pilot pulling back too soon. The airspeed is still low, so pulling back raises the angle of attack past the critical angle again, and the aircraft stalls a second time and loses even more height. The cure is patience: with full power still applied, relax the back pressure, let the aeroplane fly, and only then reapply moderate back pressure.
Part 3 · Stall recovery by type
Approach-to-stall recovery in large and small aircraft Aircraft At the warning Wing drop Then Jet (swept wing) Smoothly lower the nose to the horizon or just below ; max recommended power Roll control Gear up, take-off flap Multi-engine propeller Lower the nose to the horizon or just below; max recommended power Rudder and aileron Gear up, take-off flap Single-engine propeller Lower the nose to the horizon or just below; max recommended power Rudder Gear up if applicable All: power-on stall As power-off Prevent yaw Watch propeller torque and slipstream
On large aircraft, type training practises only the approach to the stall (to stick shaker), never the full stall.
Chapter 12 · Spins and Special Stalls
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
In airline type training on large aircraft, full stalls are not practised; only the approach to the stall, up to stick shaker activation, is flown. For a swept-wing jet there are no special considerations. At the stick shaker, smoothly lower the nose to the horizon or just below to unstall the wing, at the same time increase power to the maximum recommended to keep the height loss small, prevent any wing drop with roll control, raise the gear and select take-off flap. A power-on stall is handled the same way. A multi-engine propeller aircraft is recovered the same way, except that wing drop is prevented with rudder and aileron. The big difference from a jet is the rapidly changing propeller torque and slipstream as power is applied, so the pilot must co-ordinate rudder and aileron carefully: yaw must be prevented during the stall and recovery. In a single-engine propeller aircraft, the recovery is similar, using rudder to prevent wing drop.
Part 3 · Power-on stall
Power-on stall in a single-engine propeller aircraft High nose, low speed, high power: strong propeller turning effects Clockwise propeller (from behind): torque rolls left ; slipstream and P-factor yaw left As the nose drops at the stall, gyroscopic effect adds nose-left yaw Any yaw at the stall can become a spin : keep the ball in the middle At the first sign: pitch control forward , roll control neutral , rudder to prevent wing drop Clockwise propeller (seen from behind) Torque reaction rolls the aircraft LEFT Slipstream hits the left of the fin: yaw LEFT P-factor (high α) right-hand blade bites more: yaw LEFT Gyroscopic (nose drops) precession: yaw LEFT Hold right rudder (and right aileron); keep the ball in the middle
Chapter 12 · Spins and Special Stalls
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
A power-on stall in a single-engine propeller aircraft has extra complications. At the high nose attitude, low airspeed and high power of a power-on stall, the propeller’s turning effects are strong. For a propeller turning clockwise as seen from behind, torque reaction tries to roll the aircraft to the left, the spiralling slipstream strikes the left side of the fin and yaws the nose left, and at high angle of attack the asymmetric blade effect also yaws it left. When the nose drops at the stall, gyroscopic precession adds a further nose-left yawing moment. The pilot must hold the right rudder and aileron to stay in balance, keeping the ball in the middle, because any yaw at that moment could easily become a spin. An accidental power-on stall during take-off or a go-around could do exactly that, so act at the first sign: pitch control forward, roll control neutral, and rudder to prevent wing drop.
Part 3 · Turning stalls
Stalling in a climbing or descending turn In a turn the inner wing moves more slowly , so the aircraft tends to overbank The pilot holds aileron against the bank: the inner wing’s aileron is down So the inner (lower) wing has the higher α and may stall first Climbing left turn, clockwise prop, low speed: maybe lots of right aileron and right rudder A stall with gross control deflections can yaw or roll violently : keep the ball in the middle left (inner) wing: aileron down, slower, α highest → stalls first right aileron up Left climbing turn, clockwise propeller, low speed: right aileron against overbank + right rudder against prop yaw A stall with these crossed inputs can flick into a spin
Chapter 12 · Spins and Special Stalls
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a level, co-ordinated turn the inside wing moves more slowly than the outside wing, so it makes less lift. With the ailerons neutral, the aircraft tends to keep rolling into the turn; this is the overbanking tendency. So rather than centralising the ailerons when the bank is reached, the pilot holds a little aileron against the bank, and the lower the speed, the more is needed. That puts the inner wing’s aileron down, giving the inner, lower wing a higher effective angle of attack, so it may reach the critical angle first. In a climbing turn the speed is lower still, and in a single-engine propeller aircraft the propeller adds its own yawing and rolling forces. In a slow climbing turn to the left with a clockwise propeller, the pilot may be holding a lot of right aileron and right rudder. If the aircraft stalls like that, those large deflections can make it yaw or roll violently, so co-ordination is essential.
Part 3 · The golden rule
Whatever the stall: the same three actions In whatever configuration, attitude or power setting the stall warning comes, pretty much in this order:
1 · Reduce α Decrease the angle of attack below the stalling angle to unstall the wing . This always comes first.
2 · Power Apply maximum allowable power to minimise the height loss.
3 · No yaw Prevent any yaw from developing, to minimise the chance of a spin. Keep the ball in the middle.
Chapter 12 · Spins and Special Stalls
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull all of these situations together into one rule. In whatever configuration, attitude or power setting the stall warning occurs, the correct pilot action is, pretty much in this order: first, decrease the angle of attack below the stalling angle to unstall the wing. Second, apply the maximum allowable power to minimise the loss of height. Third, prevent any yaw from developing, to minimise the possibility of a spin. In four words: keep the ball in the middle. This is why, for example, the exam answer for a stick shaker on a swept-wing jet immediately after take-off while turning is simply to decrease the angle of attack. Reducing the bank or adding thrust may help, but neither unstalls the wing on its own, and checking whether the warning is false wastes precious seconds. And for a light single stalled power-on in a climbing left turn, the answer is stick forward, ailerons neutral, and rudder to prevent the wing drop.
Part 3 · High-speed buffet
The shock stall: buffet at high speed Above about M 0.4 air compressibility matters; jets cruise just above their critical Mach number , with a small shock on the wing An overspeed makes the shock grow rapidly , with a sharp local pressure rise The steep adverse gradient separates the boundary layer just behind the shock : the shock stall The turbulent wake engulfs the tail: severe high-speed buffet , which can damage the structure A distinct aural overspeed warning (clacker, horn or siren) sounds above VMO /MMO supersonic region shock wave boundary layer separates just behind the shock Shock stall → turbulent wake engulfs the tail → severe high-speed buffet Warning above VMO /MMO : clacker, horn or siren (quite different from the stick shaker)
Chapter 12 · Spins and Special Stalls
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Stalling is not only a low-speed problem. Above about four tenths of the speed of sound, air can no longer be treated as incompressible. A jet transport at high altitude cruises just above its critical Mach number, with a small shock wave on the wing. If the aircraft overspeeds, that shock grows rapidly and the static pressure rises sharply across it. The steep, local adverse pressure gradient makes the boundary layer separate immediately behind the shock wave. This is called a shock stall. The separated, turbulent wake streams back over the tail and causes severe airframe buffeting, which can seriously damage the structure. So an artificial high-speed warning is fitted, which sounds if the aircraft exceeds its maximum operating speed, V M O, or Mach number, M M O, by even a small margin. It is aural, a clacker, horn or siren, and easily told apart from the stick shaker of the low-speed, high angle of attack warning.
Part 3 · High-speed buffet
Low-speed and high-speed buffet close in at altitude 150 200 250 300 350 20 000 25 000 30 000 35 000 40 000 45 000 equivalent airspeed (kt) altitude (ft) VMO MMO 0.82 stick shaker (low-speed buffet) only ≈16 kt at 41 000 ft safe speed range Example jet at high weight VS1g 175 kt EAS low down; shaker at 1.07 VS ; CL max falls above M 0.4 MMO 0.82, VMO 340 kt; ISA Too slow → stall buffet Too fast → shock stall buffet At 36 000 – 42 000 ft the margin can be as small as about 15 kt Any buffet is undesirable: it can quickly damage the structure. Margins of only about 15 kt between the stall warning and the overspeed warning are possible at 36 000–42 000 ft .
Chapter 12 · Spins and Special Stalls
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Approaching the critical angle causes low-speed buffet, and flying too fast causes high-speed buffet, and any buffet is undesirable: it can quickly lead to structural damage, besides upsetting the passengers. This chart, computed for an example jet at high weight, shows why the two come together at altitude. The orange line is the stick shaker speed in equivalent airspeed. Low down it is constant, but as altitude rises the Mach number at the stall passes point four, C L max falls, and the stall warning speed creeps up. The red line is the maximum operating speed: V M O at lower levels, then, above the crossover altitude, the Mach limit, M M O, which in equivalent airspeed falls steadily as you climb. The safe band between them narrows, and around forty-one thousand feet, in this example, it is only about fifteen knots wide. That is why the operating speed limits leave a small margin for an inadvertent overspeed, and why high-altitude flying needs great care.
Part 4 · Contamination
Ice, frost and snow raise the stall speed Leading edge ice : large contour changes, severe local adverse gradients, high friction: CL max falls sharply ; VS up by about 30% ; weight adds a littleFrost : shape unchanged but rough like sandpaper; lift down up to 30%, drag up 40%; VS up about 10–15% Both make the wing stall at a smaller α Snow must be removed: it roughens the surface, hides ice, and will not blow off on take-offThe commander must ensure the aircraft is aerodynamically clean ; know the de-icing fluid’s holdover time 0 5 10 15 20 0 0.4 0.8 1.2 1.6 angle of attack α (degrees) CL clean: CL max 1.57 at 16° frost: CL max 1.30 at 13°, VS +10% leading edge ice: CL max 0.90 at 10°, VS +32% Contamination: lower CL max , smaller stalling α, higher stall speed
Chapter 12 · Spins and Special Stalls
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Any contamination on the wing, but especially ice, frost or snow, drastically alters the aerodynamic contour and the nature of the boundary layer. Ice on the leading edge changes the local shape, creating severe local adverse pressure gradients, and its rough surface adds friction and robs the boundary layer of energy. C L max falls sharply and the stall speed can rise by about thirty per cent, with the wing stalling at a smaller angle of attack. Its weight adds a little, but the lost C L max matters most. Frost is more subtle: the shape is unchanged, but a surface as rough as sandpaper can cut lift by up to thirty per cent and add forty per cent to drag, raising the stall speed by about ten to fifteen per cent. Snow roughens the surface, may hide ice, and will not blow off during taxi or take-off. The commander must ensure the aircraft is aerodynamically clean, within the holdover time of any de-icing fluid.
Part 4 · Icing-induced stall
Recognising an insidious icing-induced stall Loss of control has followed undetected stalls well above the normal stall speed , with violent roll oscillations.
Performance loss Falling performance in icing may mean a serious build-up, even if you cannot see it : lift down, drag up.
High stall speed The aircraft may stall about 30% above its normal stall speed, so gently you may not notice.
No warning The stall warning may not operate (α below its trigger). Buffet may help identify it.
Roll problem The first clue may be roll oscillation or a violent wing drop ; with high drag, a high rate of descent follows.
Act at once Suspect a wing stall: reduce α immediately .
De-ice Operate the de-icing system; anti-icing should already be on, per the manuals.
Leave the ice Change track or altitude to leave the icing conditions if possible.
The lesson Even a little ice is too much: never fly with ice, frost or snow on the aircraft.
Chapter 12 · Spins and Special Stalls
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Icing can cause a stall that creeps up insidiously, without warning. Aircraft have been lost after undetected stalls at speeds well above the normal stall speed, with violent roll oscillations. Here is the advice. A loss of performance in icing conditions may mean a serious build-up of airframe ice, even one you cannot see, cutting lift and adding drag. That ice can make the aircraft stall at about thirty per cent above its normal stall speed, and the stall can be so gentle in pitch that the pilot does not notice it. The stall warning system may not help, because the angle of attack may still be below its trigger point, though airframe buffet may. Often the first clue is a roll control problem: a growing roll oscillation or a violent wing drop, followed by a high rate of descent. So if a roll problem develops in icing, suspect a wing stall and reduce the angle of attack at once, operate the de-icing system, and consider leaving the icing conditions.
Part 4 · Tailplane stall
Stabiliser stall due to ice The tailplane is thinner than the wing, so it is likely to ice first Iced, it stalls at a smaller angle of attack It normally works at a negative α , giving a download Lowering flaps increases downwash , making the tail’s α more negative: enough to stall an iced tail Download lost: the nose pitches down and pitch control is lost. Recovery: retract the flaps wing, flaps down more downwash iced tailplane negative α grows → tail stalls Download lost → nose pitches DOWN, pitch control lost Tail is thinner than the wing: it ices first Recovery: retract the flaps again (less downwash, smaller negative α on the tail)
Chapter 12 · Spins and Special Stalls
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
The tailplane is an aerofoil too, and because it is thinner than the wing it is likely to collect ice before the wing does. Ice affects it the same way: it will stall at a smaller angle of attack. But remember that the tailplane normally works at a negative angle of attack, producing a download that balances the nose-down moment of the wing and the centre of gravity. If the tailplane stalls, that download is lost, the nose of the aircraft drops, and longitudinal control is lost. What can push an iced tailplane over the edge? Extending the wing flaps. Lowering flaps increases the downwash behind the wing, which increases the negative angle of attack of the tailplane, and with ice on it that may be enough to make it stall. Typically this happens on the approach, just as flap is selected. The recovery in this situation is to retract the flaps again, which reduces the downwash and lets the tailplane unstall.
Part 4 · Heavy rain
What heavy rain does to the stall Weight A film of water adds perhaps 1–2% to the weight, which by itself raises VS a little.
Aerodynamics The film distorts and roughens the aerofoil and alters the flow over the whole aircraft: CL max falls, VS rises .
Drag Interference, profile and form drag rise: about 5% in light rain, 20% moderate, up to 30% heavy. More thrust needed.
Impact Not a stall speed effect, but rain strikes take momentum and push the aircraft down: like microburst windshear on final.
Chapter 12 · Spins and Special Stalls
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Heavy rain has four effects. First, weight: a film of water forms over the aircraft and may add as much as one or two per cent to its weight, which on its own raises the stall speed slightly. Second, and more important, the aerodynamic effect: the water film distorts and roughens the aerofoil and alters the airflow over the whole aircraft, so C L max decreases and the stall speed increases. Third, drag: the water film increases interference, profile and form drag, by roughly five per cent in light rain, twenty per cent in moderate rain, and up to thirty per cent in heavy rain, so more thrust is needed. Fourth, the impact of the rain itself. This does not change the stall speed, but the aircraft loses momentum as it ploughs through the drops, so airspeed falls, and the rain also drives it downward. An aircraft on final approach that flies into a torrential downpour can lose speed and height much as it would in a microburst.
Summary
What to take into the exam Spin Aggravated stall + autorotation. Both wings stalled (both α positive), one more. Radius < semi-span.
Causes and phases Stall first, then crossed controls, engine failure, lateral CG. Incipient, developed, recovery.
Mass and CG Heavy: more height to recover. Aft CG: flatter spin; flat spin: tail blanked, may not recover.
Recovery Idle, ailerons neutral, full opposite rudder (turn co-ordinator), elevator to ~neutral, hold, rudder neutral, gentle pull.
Special stalls Crossed-control: ball out. Accelerated: n > 1, high speed. Secondary: pulling too soon.
Any stall Reduce α, max power, no yaw: ball in the middle. Single prop power-on: stick forward, ailerons neutral, rudder.
Shock stall Separation behind the shock; high-speed buffet; aural VMO /MMO warning; margin ~15 kt high up.
Contamination Ice VS +30%, frost +10–15%, smaller stall α. Iced tail stalls with flap: nose down, retract flap. Rain: VS up.
Chapter 12 · Spins and Special Stalls
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up this lesson. A spin is an aggravated stall resulting in autorotation, with both wings stalled at positive angles of attack, one more than the other. A stall must come first; crossed controls, an engine failure or a lateral CG imbalance can then start the rotation, which passes through incipient, fully developed and recovery phases. Heavy aircraft take longer to recover, and an aft centre of gravity gives a flatter spin, at worst a flat spin with the tail blanked. Recover with throttle idle, ailerons neutral, full opposite rudder, elevator briskly to about neutral, hold, then rudder neutral and a gentle pull-out. Crossed-control stalls show the ball out of the middle; accelerated stalls happen above one g at high speed; secondary stalls come from pulling too soon. For any stall: reduce the angle of attack, add power, prevent yaw. The shock stall is separation behind a shock wave. Ice, frost, snow and rain all raise the stall speed, and an iced tailplane can stall when flap is lowered.