Principles of Flight · Chapter 10
The Stall: Cause, Speed and Warning Why a wing stalls, what the lift curve does at the critical angle, how to recover, how stall speed is defined and changed by weight, load factor, flaps, CG, power and Mach number, and how the pilot is warned.
separated, turbulent wake CL max angle of attack → CL 16° © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the stall. Every pilot has to understand it, because a stall means a sudden loss of lift and, if it is handled badly, a loss of height and of control close to the ground. In this lesson we find out exactly what makes a wing stall, why it can happen at any speed and in any attitude, and how to recover. Then we look at stall speed: how it is defined for certification, how much warning the pilot must be given, and how weight, turning, flaps, the centre of gravity, engine power and Mach number change it. Keep one idea in mind all the way through: a wing stalls at an angle of attack, not at a speed.
Lesson map
What this lesson covers 1 · Why wings stall Boundary layer energy, the adverse pressure gradient and the critical angle of attack .
2 · Lift curve and recovery CL max , what happens beyond it, how to recover and how to recognise a stall.
3 · Stall speed and warning VS1g , VSR , VSW , stick shaker and pusher margins, and the sensors.
4 · What changes VS Weight, load factor in turns, flaps, CG, gear, power and Mach number, with numbers.
Chapter 10 · The Stall: Cause, Speed and Warning
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for this lesson, in four parts. First, the physics: why the airflow breaks away from a wing at a certain angle of attack, which we call the critical or stalling angle. Second, the lift curve, what happens to lift and drag beyond the stall, how a pilot recovers, and what the regulations accept as proof that an aeroplane has stalled. Third, stall speed and stall warning: the reference stall speed used for large aeroplanes, the warning margin the pilot must be given, and the devices that sense the approach of a stall. Fourth, the factors that change stall speed. We will calculate the effect of weight and of bank angle with real numbers, and see why flaps, the centre of gravity, the landing gear, engine power and Mach number all matter. Wing design, spins and the special stalls follow in the next two lessons.
Part 1 · Cause of the stall
Separation: the boundary layer runs out of energy A stall is caused by airflow separation from the upper surface Behind the suction peak the air must flow into rising pressure : the adverse pressure gradient Separation comes when the boundary layer has too little kinetic energy or the gradient is too steep Raising α raises the suction peak, so the gradient steepens Past the critical angle (about 16° ), CL falls and drag rises sharply CL max sets the minimum steady flight speed , the 1g stall speed 0 0.25 0.5 0.75 1 0 1 2 3 4 5 distance along chord (x/c) suction on upper surface (−Cp ) α = 3° α = 6° α = 9° steep pressure rise behind the peak = adverse pressure gradient Boundary layer must climb this "hill" using its own energy Too steep a hill or too little energy → it stops and separates
Chapter 10 · The Stall: Cause, Speed and Warning
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A stall is caused by the airflow separating from the upper surface of the wing. Look at the chart. It shows the suction along the upper surface, worked out for a real section. Near the leading edge there is a strong suction peak, and behind it the pressure rises again towards the trailing edge. The air in the boundary layer has to flow uphill into that rising pressure, which we call the adverse pressure gradient, and it can only do so using its own kinetic energy, which friction is already wearing down. Now see what happens as the angle of attack goes from three to six to nine degrees: the peak grows very fast, so the pressure hill gets much steeper. Separation happens when the boundary layer has too little energy, or the gradient becomes too steep. Beyond the critical angle, about sixteen degrees for a typical wing, lift coefficient falls and drag climbs. The highest lift coefficient, C L max, sets the minimum steady flight speed.
Part 1 · Cause of the stall
The separation point creeps forward Low α: flow stays attached as a turbulent boundary layer to the trailing edge Higher α: the boundary layer first separates at the trailing edge Further increase: the separation point moves forward Less of the wing makes a pressure difference, so lift growth slows Above about 16° separation is so widespread that lift cannot support the weight α 4°: attached to the trailing edge α 12°: separation starts near the trailing edge S α 18°: separation point far forward: stalled S S = separation point: it creeps forward as α increases
Chapter 10 · The Stall: Cause, Speed and Warning
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us watch the separation develop. At a small angle of attack, the flow stays attached all the way to the trailing edge; over the rear part the boundary layer is turbulent, but it still follows the surface. As the angle increases, the adverse pressure gradient steepens and the boundary layer first breaks away at the trailing edge. Increase the angle further and the separation point moves forward along the upper surface, so a smaller part of the wing is producing a useful pressure difference, and the lift curve starts to bend over. Finally, above about sixteen degrees, separation is so widespread that the wing cannot produce enough lift to support the weight of the aeroplane. Notice the eddies in the wake: that turbulent air is what shakes the airframe and the tail, and we feel it as buffet.
Part 1 · Cause of the stall
Any speed, any attitude Angle of attack is measured between the chord and the relative airflow The relative airflow comes from the direction of the flight path , not from the horizon So pitch attitude does not tell you α : a steep climb can be well below the stall A sharp pull-out from a dive can stall the wing with the nose below the horizon An aeroplane can be stalled at any airspeed and any attitude A given wing always stalls at the same angle of attack Steep climb, fast nose +25°, path +20° α 5°: flying Level, slow nose +16°, path +0° α 16°: at the critical angle Pull-out from a dive nose -10°, path -28° α 18°: stalled α = angle between the chord and the relative airflow (opposite to the flight path)
Chapter 10 · The Stall: Cause, Speed and Warning
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
A wing can stall at any airspeed and in any attitude. That follows directly from the definition: angle of attack is the angle between the chord line and the relative airflow, and the relative airflow comes from the direction the aircraft is actually moving, not from the horizon. Look at the three cases. In a fast, steep climb the nose is twenty-five degrees up, but the flight path is twenty degrees up too, so the angle of attack is only five degrees and the wing flies happily. In slow level flight the nose is sixteen degrees up and the path is level, so the wing is at the critical angle. And in a hard pull-out from a dive the nose can still be below the horizon while the path is even steeper downward, so the angle of attack exceeds the critical angle and the wing stalls at high speed. A given wing always stalls at the same angle of attack.
Part 2 · The lift curve
The lift curve and the drag curve through the stall -4 0 4 8 12 16 20 24 0 0.4 0.8 1.2 1.6 angle of attack α (degrees) CL stalled CL max ≈ 1.57 straight-line range (flow attached) slope falls off: separation begins critical angle 16° 0 8 16 24 0.0 0.1 0.2 0.3 0.4 α (degrees) CD drag rises steeply past the stall Beyond the critical angle lift decreases and drag increases : the aeroplane sinks, and the extra drag makes it slow down further.
Chapter 10 · The Stall: Cause, Speed and Warning
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the lift curve for a typical cambered section, computed from a smooth model. From the zero-lift angle, about minus two degrees, the lift coefficient rises in a straight line over a wide range of angles, because the flow is attached. Above about ten degrees the effects of separation begin to be felt and the slope falls off. The curve then reaches its peak, C L max, at about sixteen degrees, and that is the stalling or critical angle of attack. Push the angle further and the lift coefficient falls. Now look at the drag curve on the right. Below the stall drag grows slowly, but beyond it drag increases very rapidly, because the wake is now a broad region of turbulent, separated air. Remember the exam phrase: above the stalling angle, lift decreases and drag increases. The aeroplane loses height, and the rising drag slows it further.
Part 2 · Stall recovery
Recovery: first reduce the angle of attack Decrease α : release back pressure, or move the pitch control smoothly forwardNot too far forward: negative g on the wing delays recovery Jet transport: nose to the horizon or just below with maximum authorised power Wing drop: rudder on straight wings; ailerons with a little co-ordinated rudder on swept wings Regain height with moderate back pressure : a hard pull risks a secondary stall or over-stressing 1 Stalled α above critical 2 Nose to horizon reduce α · max power 3 Fly away moderate back pressure Wing drop: rudder (straight wing) · aileron + a little co-ordinated rudder (swept wing) Too hard a pull → secondary stall or over-g Too hard a push → negative g, slower recovery
Chapter 10 · The Stall: Cause, Speed and Warning
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
To recover from a stall, or to stop one developing, the angle of attack must be reduced so that the adverse pressure gradient eases and the flow re-attaches. Sometimes simply releasing the back pressure is enough; sometimes the pitch control must be moved smoothly forward, depending on the type and how deep the stall is. But do not push too far forward: a large push puts a negative load on the wing and actually delays the recovery. On a modern jet transport it is usually enough to lower the nose to the horizon or just below while applying maximum authorised power to keep the height loss small. If a wing drops, use rudder on a straight-winged aircraft; on a swept wing use the ailerons with a little smooth, co-ordinated rudder, because the big rudder can over-roll the aircraft. Finally, let the speed build and climb back with moderate back pressure. Pulling hard can cause a secondary stall, or exceed the limit load factor.
Part 2 · Behaviour near the stall
Controls near the stall: beware the aileron First signs: unresponsive (“mushy”) controls , a stall warning , or aerodynamic buffet Low dynamic pressure: larger deflections needed for the same response A control deflection changes the chord line , so it changes α Lowering an aileron to lift a dropping wing raises that wing’s α and can stall it fully Straight wings: use rudder to yaw just enough to speed up the low wing Swept wings are certified for aileron use up to stall recognition relative airflow 15° Aileron neutral: α 15° relative airflow 22° Aileron down: effective α 22° Down-going aileron = more camber and a larger α at that wing
Chapter 10 · The Stall: Cause, Speed and Warning
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
As the stall approaches, the first signs may be controls that feel unresponsive or mushy, a stall warning, or aerodynamic buffet. The controls feel mushy because dynamic pressure is now very low, so a much bigger deflection is needed for the same response. Here is the trap. Moving a control surface changes the effective chord line, and so it changes the angle of attack. Suppose one wing produces a little less lift and drops. If the pilot tries to lift it with aileron, that wing’s aileron goes down. In the diagram the section was at fifteen degrees; with the aileron down by about twenty-eight degrees the effective chord is now at twenty-two degrees, beyond the critical angle. That wing stalls completely and drops even faster. So near the stall, on a straight wing, use rudder to yaw the aircraft just enough to speed up the dropping wing. Swept-wing transports are designed so the ailerons can be used up to stall recognition, with small co-ordinated rudder.
Part 2 · Stall recognition
When is an aeroplane officially stalled? For certification, the aeroplane is stalled when its behaviour gives the pilot a clear and distinctive indication of an acceptable nature. Acceptable indications, alone or together:
Nose-down pitch A nose-down pitch that cannot be readily arrested by the pilot.
Deterrent buffet Buffeting of a magnitude and severity that is a strong and effective deterrent to slowing further.
Stick on the aft stop The pitch control reaches the aft stop and, held there briefly, no further increase in pitch attitude occurs.
Chapter 10 · The Stall: Cause, Speed and Warning
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
When is an aeroplane officially stalled? For certification, it is stalled when its behaviour gives the pilot a clear and distinctive indication, of an acceptable nature, that it has stalled. There are three acceptable indications, and they may appear on their own or together. The first is a nose-down pitch that the pilot cannot readily stop. The second is buffeting so strong and so severe that it is an effective deterrent to slowing down any further. The third is that the pitch control reaches its aft stop and, when it is held fully back for a short time, the pitch attitude does not increase any further. Learn these three, because the exam often asks you to pick them out from a list. And remember the point behind them: the pilot must be able to identify a stall clearly and unmistakably, so that it can be prevented or recovered from at once.
Part 3 · Stall speed
The reference stall speed, VSR Stall speeds are found in flight test before certification and printed in the Flight Manual Small aeroplanes (CS-23) use VS0 and VS1 Large aeroplanes (CS-25) use the reference stall speed VSR , a CAS set by the manufacturer VSR may not be less than a 1g stall speed No stick pusher: VSR ≈ VS1g ; with a pusher, VSR ≥ push speed +2 kt or 2% Take-off, approach and landing speeds are set as multiples: 1.13, 1.2, 1.3 VSR Large aeroplanes (CS-25) VSR ≥ VCLMAX ⁄ √nZW nZW = load factor normal to the flight path at VCLMAX At 1g the reference stall speed equals the 1g stall speed Sample aircraft: VCLMAX = 150 kt CAS 130 140 150 160 170 180 190 200 210 VSR 150 1.13 VSR ≈ 170 1.3 VSR = 195 stalled trim band for test Slow down at no more than 1 kt per second kt CAS Small aeroplanes (CS-23) quote VS0 (landing) and VS1 (stated configuration)
Chapter 10 · The Stall: Cause, Speed and Warning
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Take-off and landing are flown slowly to keep runways short, so there must be a defined margin above an agreed stall speed, measured in flight test and printed in the Flight Manual. Small aeroplanes under C S twenty-three quote V S zero, in the landing configuration, and V S one. Large aeroplanes under C S twenty-five use the reference stall speed, V S R. It is a calibrated airspeed chosen by the manufacturer, and it may not be less than a one g stall speed. Formally, V S R is at least V C L max divided by the square root of the load factor normal to the flight path. Without a stick pusher, V S R is effectively the one g stall speed. With a pusher it must be at least two knots or two per cent, whichever is greater, above the push speed. Operating speeds such as one point one three or one point three V S R are built on it.
Part 3 · Stall speed
How VCLMAX is measured Condition Requirement Why it matters Thrust Zero thrust at the stall speedThrust would hold some weight up and lower VS Propeller Pitch controls in the take-off position A standard, repeatable setting Configuration Flaps and gear as in the test or performance standard being used CL max depends on configuration Weight The weight at which VSR is applied VS rises with √weight CG The position giving the highest VSR (normally the forward limit) More tail download, more lift needed Trim and entry Trimmed at 1.13 – 1.3 VSR , then slowed at ≤ 1 kt per second Slow, steady approach to the true 1g stall Stick pusher VSR ≥ push speed + 2 kt or 2% , the greater You cannot fly slower than the push
Other things that change VSR : load factor, thrust above zero and wing contamination. Density altitude does not change the indicated stall speed.
Chapter 10 · The Stall: Cause, Speed and Warning
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Flight Manual stall speeds are measured under strict conditions, and each one hints at what affects stall speed. Thrust is zero at the stall, because thrust would carry part of the weight and lower the stall speed. Flaps and landing gear are set as for whatever performance standard the speed will be used for, because C L max depends on configuration. The weight is the weight at which the speed will be used. The centre of gravity is placed where it gives the highest stall speed, which is normally the forward limit. The aircraft is trimmed between one point one three and one point three V S R, then slowed at no more than one knot per second, so the stall is a true, steady one g stall. If a stick pusher is fitted, V S R must be at least two knots or two per cent above the speed at which it fires. And remember: density altitude does not change the indicated stall speed.
Part 3 · Stall warning
Stall warning margins No stick pusher 136 138 140 142 144 146 148 150 152 154 156 158 160 VSR = VS1g = 150 VSW ≥ 157.5 +5 kt or 5%, the greater Stick pusher fitted (push at 140 kt) 136 138 140 142 144 146 148 150 152 154 156 158 160 push 140 VSR ≥ 142.8 +2 kt or 2% VSW ≥ 147.1 +3 kt or 3% above VSR kt CAS · slow-down rate not more than 1 kt per second Warning must be clear and distinctive in straight and turning flight; a visual warning alone is not acceptable . It must continue until α is reduced to about where it began.
Chapter 10 · The Stall: Cause, Speed and Warning
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The regulations demand clear and distinctive warning far enough ahead of the stall for the pilot to avoid it, in straight and turning flight, in any normal configuration. The warning may come from the aircraft’s own aerodynamic behaviour, or from a device, but a visual warning that needs the crew to be looking inside the cockpit is not acceptable on its own. Look at the top scale. With no stick pusher, the reference stall speed is one hundred and fifty knots, and warning must begin at least five knots or five per cent above the stall, whichever is greater. Five per cent is seven and a half knots, so warning by one hundred and fifty-seven and a half. The lower scale has a pusher firing at one hundred and forty knots. V S R must be two per cent higher, one hundred and forty-two point eight, and warning at least three per cent above that, about one hundred and forty-seven.
Part 3 · Stall warning devices
Artificial stall warning and the flapper switch Natural buffet is not usually enough , so a device that simulates buffet is fitted Small aircraft: a horn or buzzer Large aircraft: a stick shaker (motors with out-of-balance weights) plus lights and a noise-maker for when hands are off Flapper switch : as α rises the stagnation point moves down and back round the leading edgeAt the set α it reaches the underside of the tab and the higher pressure lifts it, closing the switch Low α: stagnation point near the nose stagnation point flapper switch open High α: stagnation point under the tab stagnation point flapper switch lifted: warning ON
Chapter 10 · The Stall: Cause, Speed and Warning
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Natural buffet from early separation can warn the pilot, shaking the wing and the tail and even the control column. But usually that is not enough, so a device that simulates buffet is fitted. On small aircraft it is a horn or a buzzer. On large aircraft it is a stick shaker: a pair of small electric motors, one on each control column, each spinning an out-of-balance weight. It is tactile, so if the pilots’ hands are off the controls, with the autopilot engaged for example, a noise-maker and lights work in parallel. What triggers it? The simplest sensor is the flapper switch on the leading edge. Watch the stagnation point, where the flow divides. As the angle of attack increases, it moves downwards and backwards round the leading edge. The switch is placed so that at the chosen angle the stagnation point reaches its underside, and the higher pressure there lifts the tab and closes the warning circuit.
Part 3 · Stall warning sensors
Angle of attack vanes and probes AoA vane on the fuselage side: it streamlines with the airflow while the fuselage rotates round itAoA probe : slots in a probe sense the angle of the relative airflowThey sense angle of attack , so changes in mass are taken care of automatically Most also use the rate of change of α , giving earlier warning in a fast approach to the stall Datum compensated for configuration , always heated , and fitted on both sides to cancel sideslip relative airflow α vane The vane lines up with the airflow; the fuselage pitches round its pivot AoA probe slots sense flow angle
Chapter 10 · The Stall: Cause, Speed and Warning
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Larger aircraft use an angle of attack vane or probe. The vane is mounted on the side of the fuselage. Like a weathercock it lines itself up with the relative airflow, and as the aircraft pitches the fuselage rotates around it, so the angle between the two is a direct measure of the angle of attack. The probe does the same job with slots in a small tube that are sensitive to the direction of the airflow. All these sensors, the flapper switch included, measure angle of attack, not speed. Because the stall always happens at the same angle of attack, a change in the aircraft’s mass is taken care of automatically. Most systems also compute the rate at which the angle of attack is increasing and give an earlier warning when the stall is approached quickly. The sensors are compensated for flap and slat configuration, they are always heated against ice, and there is one on each side so that sideslip does not upset them.
Part 3 · Certification
Basic stall requirements (EASA and FAR) Requirement What the aeroplane must do Roll and yaw control Possible to produce and correct roll and yaw with unreversed aileron and rudder, up to the stall Pitch No abnormal nose-up pitching ; longitudinal control force positive up to and through the stallRecovery Possible to promptly prevent a stall and to recover by normal use of the controls Wings-level stall Roll between the stall and the end of recovery not more than about 20° Turning stall, ≤ 1 kt/s Bank during recovery not more than about 60° into the turn or 30° away from it Turning stall, > 1 kt/s Not more than about 90° into the turn or 60° away from it
Turning-flight stalls must not be so violent or extreme that a prompt recovery needs more than normal piloting skill.
Chapter 10 · The Stall: Cause, Speed and Warning
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The certification rules also say how an aeroplane must behave at the stall. Up to the moment it stalls, it must be possible to produce and to correct roll and yaw with the ailerons and rudder working the normal way round, not reversed. There must be no abnormal nose-up pitching, and the force on the pitch control must be positive, meaning you still have to pull, right up to and through the stall. It must be possible to prevent a stall promptly and to recover from one using the controls normally. In a wings-level stall the roll between the stall and the end of the recovery must not exceed about twenty degrees. In a turning stall at a deceleration of up to one knot per second, the bank during recovery must stay within about sixty degrees in the direction of the turn or thirty degrees the other way. With faster deceleration, the limits open to about ninety degrees and sixty degrees.
Part 4 · Stall speed
The 1g stall speed Load factor n = Lift ÷ Weight; straight and level, n = 1 (“1g”)L = ½ρV²CL S: slow down and CL (so α) must rise to keep L = W Each lower CAS needs a larger α, until the wing reaches CL max VS1g = √( L ÷ ½ρ CL max S ) In EAS (≈ CAS) terms ρ is sea-level density, so density altitude does not change the indicated stall speed 120 150 180 210 240 270 300 0 0.5 1 1.5 2 calibrated airspeed (kt) CL needed for L = W CL max = 1.5 VS1g = 150 kt CL 0.84 CL 0.54 slower → bigger CL → bigger α CL needed ∝ 1 ⁄ V² (lift, density and wing area fixed)
Chapter 10 · The Stall: Cause, Speed and Warning
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us build the stall speed formula. Load factor, n, is lift divided by weight; in straight and level flight lift equals weight, so the load factor is one, which pilots call one g. Lift equals half rho V squared, times C L, times the wing area. Hold density and area fixed and throttle back: speed falls, so to keep lift equal to weight the lift coefficient must rise, which means a bigger angle of attack. The chart shows a sample aircraft: the lift coefficient needed rises as one over V squared as speed falls. Eventually, at one particular calibrated airspeed, the wing reaches C L max, and any attempt to slow further stalls it. That speed is the one g stall speed: the square root of lift divided by half rho times C L max times S. Because indicated airspeed already reflects dynamic pressure, density altitude does not change the indicated stall speed.
Part 4 · Weight
Weight changes stall speed, not stall angle More weight needs more lift: at CL max that means more speed VS new = VS old × √(new weight ÷ old weight) Example: 588 600 N → 470 880 N, VS 150 kt → 134 kt CAS Rule of thumb: VS changes by about half the % change in weight (good for small changes) The stalling angle of attack is not affected by weight (below about M 0.4) 0.4 0.6 0.8 1 1.2 0.6 0.7 0.8 0.9 1.0 1.1 1.2 new weight ÷ old weight new VS ÷ old VS dashed: rule of thumb, half the % change −20% weight → −10.6% VS −50% → −29% +20% → +9.5% 588 600 N → 470 880 N: 150 × √0.8 = 134 kt The stalling angle of attack does not change
Chapter 10 · The Stall: Cause, Speed and Warning
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
At C L max the only way to make more lift is more dynamic pressure, so a heavier aircraft stalls at a higher speed. Stall speed varies with the square root of weight: the new stall speed equals the old one times the square root of new weight over old weight. Worked example: an aircraft stalls at one hundred and fifty knots at five hundred and eighty-eight thousand, six hundred newtons. What is the stall speed at four hundred and seventy thousand, eight hundred and eighty newtons? The weight ratio is point eight, its square root is about point eight nine four, and one hundred and fifty times that is one hundred and thirty-four knots. So a twenty per cent cut in weight gives roughly a ten per cent cut in stall speed: the rule of thumb is half the percentage. Be careful with big changes: halving the weight lowers stall speed by twenty-nine per cent, not twenty-five. And note well: weight does not change the stalling angle of attack.
Part 4 · Load factor
Why a level turn needs more lift Weight always acts vertically down In a bank, lift tilts; only its vertical component L cos φ balances weight So L = W ÷ cos φ ; the horizontal part L sin φ turns the aircraft 45° bank: L = 1 ÷ 0.707 = 1.41 W (lift up 41%) n = L ÷ W rises with bank angle only ; the extra lift comes from a larger α Lift = W ÷ cos φ L cos φ = W L sin φ (turns) Weight W φ 45° n = L ⁄ W = 1 ⁄ cos 45° = 1.41 (lift up 41%)
Chapter 10 · The Stall: Cause, Speed and Warning
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does a turn raise the stall speed? Weight always acts straight down. When the aircraft banks, lift tilts with the wings, and only its vertical component, lift times the cosine of the bank angle, is available to hold the weight up. The horizontal component is what pulls the aircraft round the turn. To stay level, the vertical component must still equal the weight, so lift must become weight divided by the cosine of the bank angle. In a forty-five degree bank the cosine is point seven oh seven, so lift must be one point four one times the weight: forty-one per cent more. The load factor, lift over weight, therefore depends on bank angle only, whatever the type of aircraft. And where does the extra lift come from at the same speed? From a larger angle of attack. That is the key: the turn uses up some of your margin to the critical angle.
Part 4 · Load factor
Stall speed rises with the square root of load factor 0 10 20 30 40 50 60 70 80 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 bank angle φ in a level turn (degrees) ratio to wings-level value +7% n 1.15 +19% n 1.41 +41% n 2.00 Load factor n = 1 ⁄ cos φ (dashed) Stall speed in the turn VS turn = VS1g × √n (solid) Rises at an increasing rate: gentle to 30°, steep beyond 45° Same stalling angle of attack VS turn = VS1g × √(1 ⁄ cos φ) = VS1g × √n . The stalling angle is unchanged; only the speed at which it is reached goes up.
Chapter 10 · The Stall: Cause, Speed and Warning
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
If you start a turn at a speed just above the stall, then at some bank angle the wing will need C L max to provide the extra lift, and it stalls at a speed higher than the one g stall speed. Because lift needed goes up with the load factor and lift goes with speed squared, stall speed goes up with the square root of the load factor. Look at the curves. The dashed line is the load factor, one over cos phi; the solid line is the stall speed ratio, its square root. Both rise slowly at first and then faster and faster. At thirty degrees the stall speed is seven per cent higher, at forty-five degrees nineteen per cent, and at sixty degrees forty-one per cent, with the load factor doubled. These are ratios, so they are true for any aeroplane. And the stalling angle of attack does not change in a turn; the wing simply reaches it at a higher speed.
Part 4 · Worked numbers
Stall speeds in a level turn (VS1g = 150 kt) Bank φ Load factor n Lift increase √n Stall speed Increase 0° 1.00 0% 1.000 150 kt — 15° 1.04 4% 1.018 153 kt 2% 25° 1.10 10% 1.050 158 kt 5% 30° 1.15 15% 1.075 161 kt 7% 45° 1.41 41% 1.189 178 kt 19% 60° 2.00 100% 1.414 212 kt 41%
Working back: 153 kt in a 15° bank → VS1g = 153 ÷ √(1 ⁄ cos 15°) = 153 ÷ 1.02 = 150 kt . Jet transports: absolute maximum bank about 30° , normal 25° , and 10–15° at high altitude.
Chapter 10 · The Stall: Cause, Speed and Warning
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the numbers for a one g stall speed of one hundred and fifty knots. In a fifteen degree bank the load factor is one point oh four and the stall speed only one hundred and fifty-three knots. At thirty degrees the lift is fifteen per cent up and the stall speed one hundred and sixty-one, seven per cent higher. At forty-five degrees, one hundred and seventy-eight; and at sixty degrees, with the load factor two, a stall speed of two hundred and twelve knots, forty-one per cent above the wings-level value. You can also work backwards. If an aircraft stalls at one hundred and fifty-three knots in a fifteen degree bank, divide by the square root of one over cos fifteen, which is one point oh two, and you get a one g stall speed of one hundred and fifty knots. That is why jet transports keep the bank to about twenty-five degrees normally, thirty at most, and only ten to fifteen degrees at high altitude.
Part 4 · Configuration
High lift devices lower the stall speed Swept jet wings are thin (about 12% t/c), so clean CL max is low and clean VS high Leading edge flaps and slats and trailing edge flaps raise CL max , by up to 100% From the formula, higher CL max → lower VS TE flaps stall at a smaller α ; slats at a larger α Their sole purpose : lower minimum speed for shorter take-off and landing ; they also alter stall behaviour -10 0 10 20 0 0.5 1 1.5 2 2.5 3 angle of attack α (degrees) CL clean: CL max 1.57 at 16° TE flaps: CL max 2.21 at 13° LE slats: CL max 2.36 at 24° Higher CL max → lower stall speed CL max doubled → VS × 1 ⁄ √2 = 0.71 (29% lower)
Chapter 10 · The Stall: Cause, Speed and Warning
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Jet transports have thin swept wings, about twelve per cent thick, so their clean C L max is low and their clean stalling speed high. To bring take-off and landing speeds down, they use high lift devices: leading edge flaps and slats, and trailing edge flaps. From the stall speed formula, a higher C L max means a lower stall speed, and the best modern systems can raise C L max by as much as one hundred per cent. Doubling C L max divides the stall speed by root two, a twenty-nine per cent reduction. Look at the shapes of the curves. Trailing edge flaps add camber, lifting the whole curve, but the wing stalls at a smaller angle of attack. Slats keep the flow attached to a much larger angle, so the curve simply carries on higher. Their sole purpose is a lower minimum flight speed and shorter take-off and landing runs, but they also change the stalling characteristics, as the next lessons show.
Part 4 · CG and landing gear
Forward CG and gear down raise the stall speed CG ahead of the CP : a nose-down moment that the tailplane balances with a download The wing must lift weight plus tail download , so VS rises Forward CG → higher stall speed ; VSR is measured at the most adverse CGGear down : drag below the CG pitches the nose down → more download → higher VS The CG shift as the gear moves is insignificant; the gear drag is what matters Lift = W + tail load Weight tail download CG CP gear drag below the CG CG forward or gear down → more tail download → more lift needed → higher stall speed
Chapter 10 · The Stall: Cause, Speed and Warning
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the centre of gravity. On a conventional aircraft the centre of gravity normally lies ahead of the centre of pressure of the wing. Weight acting ahead of lift gives a nose-down pitching moment, and if no thrust or drag moment opposes it, the tailplane must push down to balance it. That tail download is an extra downward force, so the wing must now lift the weight plus the tail load. More lift needed means a higher stall speed. Move the CG further forward and the moment arm grows, the download grows, and stall speed rises. That is why V S R is measured at the CG that gives the highest stall speed, normally the forward limit. Extending the landing gear works the same way. The gear legs hang below the CG, so their drag gives a nose-down moment, which needs more tail download, which needs more lift. Any CG shift as the gear swings is insignificant; it is the drag of the gear that raises the stall speed.
Part 4 · Engine power
Power lowers the stall speed VCLMAX is measured at zero thrust : lift carries all the weight Near the stall the nose is high, so thrust has a vertical component that supports part of the weight Propellers : the slipstream raises dynamic pressure over the wing, giving much more lift at the same αCutting power suddenly in the flare can lose lift and give a heavy landing Jets : only the thrust component; stall α is the same power-on and power-off Power-on VS < power-off VS Thrust T T sin θ helps hold the weight up slipstream: faster air over the wing behind the prop Less lift needed from the wing, and more lift at the same α: power-on VS < power-off VS VCLMAX is measured with zero thrust
Chapter 10 · The Stall: Cause, Speed and Warning
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Stall speed is measured with zero thrust, so that lift carries the entire weight. Add power close to the stall and two things happen. First, the nose is high, so the thrust line points upward and thrust has a vertical component that holds up part of the weight, so the wing needs less lift. Second, on a propeller aircraft the slipstream behind the propeller is faster than the free stream, so the dynamic pressure over the part of the wing in the slipstream is much higher, and the wing produces much more lift at the same angle of attack and airspeed. That cuts both ways. In the flare, chopping the power suddenly removes that lift and can cause a heavy landing. A jet has no slipstream over the wing, so only the vertical thrust component matters, and its stalling angle is essentially the same power-on as power-off. Either way, the power-on stall speed is lower than the power-off stall speed.
Part 4 · Mach number
Compressibility raises the stall speed at altitude 0.0 0.2 0.4 0.6 0.8 0.6 0.8 1.0 1.2 1.4 1.6 Mach number CL max M 0.4: compressibility starts to matter 120 140 160 180 200 0 10 000 20 000 30 000 40 000 1g stall speed, EAS (kt) altitude (ft) cannot fly at 1g here 150 kt = M 0.4 at ≈28 000 ft (ISA) stall speed rises with altitude Above about M 0.4 the flow approaches the wing more steeply, the leading edge pressure gradient sharpens and CL max falls , so VS rises and the stall comes at a smaller α .
Chapter 10 · The Stall: Cause, Speed and Warning
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Above about four tenths of the speed of sound, compressibility starts to matter. Pressure waves from the wing travel ahead at the speed of sound and warn the oncoming air to start moving up towards the low pressure on top. At low speed this upwash begins far ahead of the wing. At higher speed the wing is closer behind its own pressure waves, so the air has less distance and must approach more steeply. That sharpens the adverse pressure gradient near the leading edge and separation comes at a smaller angle of attack, so C L max falls, as the left chart shows. Now the right chart. At a constant equivalent airspeed, true airspeed rises with altitude and the speed of sound falls, so Mach number increases. Low down, the stall speed of one hundred and fifty knots is below Mach point four, so it does not change with altitude. At about twenty-eight thousand feet in the standard atmosphere it reaches Mach point four, and above that the stalling boundary curves away to higher speeds.
Summary of factors
What changes the stall speed Change Stall speed (IAS) Stalling α Reason Weight up Up ∝ √WSame More lift needed at CL max Load factor up (turn, pull-up) Up ∝ √nSame n = 1 ⁄ cos φ in a level turn Flaps / slats out Down Flaps: smaller · slats: larger CL max raised CG forward / gear down Up Same More tail download Power on Down Jet: same Thrust component, prop slipstream Mach above ≈ 0.4 Up Smaller CL max falls (compressibility) Altitude (below M 0.4) Unchanged Same IAS stall fixed; TAS stall higher
Contamination (ice, frost, snow) and heavy rain also raise stall speed: see the lesson on special stalls.
Chapter 10 · The Stall: Cause, Speed and Warning
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the factors together. Increase the weight and the stall speed rises with the square root of weight, at the same stalling angle. Increase the load factor, in a turn or a pull-up, and the stall speed rises with the square root of the load factor, again at the same angle. Extend flaps or slats and C L max goes up, so the stall speed comes down; trailing edge flaps stall at a smaller angle, slats at a larger one. A forward CG or extended landing gear means more tail download and so a higher stall speed. Engine power lowers the stall speed, through the vertical thrust component and, on propeller aircraft, the slipstream. Above about Mach point four, compressibility reduces C L max, raising the stall speed and lowering the stalling angle. And at speeds below Mach point four, altitude makes no difference to the indicated stall speed.
Summary
What to take into the exam Cause Separation: boundary layer too little energy or adverse gradient too steep. Critical α ≈ 16°.
Curve Beyond CL max : lift down, drag up. Stall at any speed and attitude, same α.
Recovery Reduce α, max power, rudder for wing drop (straight wing), moderate back pressure.
Recognition Unarrested nose-down pitch, deterrent buffet, or stick on aft stop with no more pitch.
VSR and VSW VSR ≥ VS1g ; pusher +2 kt/2%. Warning ≥ +5 kt/5% (≥ VSR +3 kt/3%).
Devices Horn or stick shaker; flapper switch, AoA vane or probe. Sense α (and its rate).
Numbers VS ∝ √W and √n. 30° +7%, 45° +19%, 60° +41%. 588 600 → 470 880 N: 150 → 134 kt.
Factors Flaps, power: VS down. Forward CG, gear, Mach > 0.4: VS up.
Chapter 10 · The Stall: Cause, Speed and Warning
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
A stall is caused by separation, when the boundary layer has too little energy or the adverse pressure gradient is too steep, at a critical angle of about sixteen degrees. Beyond C L max, lift falls and drag rises, and a wing can stall at any speed and attitude, but always at the same angle of attack. Recover by reducing the angle of attack, applying maximum power and using rudder for wing drop on a straight wing, then climb back gently. V S R is at least the one g stall speed, two knots or two per cent above any pusher, and warning starts at least five knots or five per cent above the stall. Warning devices sense angle of attack. Stall speed varies with the square root of weight and of load factor. Flaps and power lower it; a forward centre of gravity, the gear and high Mach number raise it.