Principles of Flight · Chapter 9
Total Drag, Power and Speed Stability Putting parasite and induced drag together: the total drag curve, the minimum drag speed and L/D max, the effects of weight, altitude and configuration, speed stability, and power required.
VMD total drag parasite induced IAS DRAG © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to chapter nine, the last of our three lessons on drag. We now add parasite drag and induced drag together and get one of the most important graphs in the whole of aircraft performance: the total drag curve. From it come the minimum drag speed, the best lift to drag ratio, and the reason an aircraft flown slower than its minimum drag speed behaves so differently from one flown faster. We will see how weight, altitude and configuration move the curve, why pilots on the approach must watch their speed so carefully, and finally how drag turns into power required, which brings us to the minimum power speed.
Lesson map
Total drag, power and speed stability 1 · The curve Total drag = parasite + induced; VMD and the L/D ratio.
2 · What moves it Weight , altitude and configuration .
3 · Speed stability The front and the back of the drag curve.
4 · Power required Drag × TAS , and VMP compared with VMD .
Chapter 9 · Total Drag, Power and Speed Stability
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through the final drag lesson. First we build the total drag curve by adding the two drag families, find the minimum drag speed, V M D, and connect it to the lift to drag ratio and the drag polar. Second we see how weight, altitude and configuration move the curve, and what that does to V M D. Third we look at speed stability: why an aircraft trimmed faster than V M D tends to hold its speed, and one trimmed slower tends to wander away from it. Finally, we turn drag into power required, and find the minimum power speed, V M P, which is slower than V M D.
The total drag curve
Total drag = parasite drag + induced drag 100 150 200 250 300 350 10 20 30 40 IAS (kt) drag (kN) minimum total drag: L/D max parasite = induced VMD total drag parasite ∝ IAS² induced ∝ 1 / IAS² induced drag dominates parasite drag dominates Drawn for one weight and configuration in level flight. Induced drag dominates at low IAS , parasite drag at high IAS ; the minimum is at VMD .
Chapter 9 · Total Drag, Power and Speed Stability
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the total drag curve for one aircraft, at one weight and one configuration, in level flight. The blue dashed line is parasite drag, rising with the square of the IAS. The purple dashed line is induced drag, falling with one over the IAS squared. Add them at every speed and you get the red total drag curve, which is U-shaped. At low speed, induced drag dominates and total drag is high. At high speed, parasite drag dominates and total drag is high again. In between there is a minimum, and because of the particular way the two drags vary with speed, that minimum falls exactly where parasite drag and induced drag are equal. The speed at the bottom of the curve is the minimum drag speed, V M D. In our example it is two hundred knots, where each drag is ten kilonewtons and the total is twenty.
The numbers
Why the minimum is where the two are equal Parasite drag = 10 kN × (V/200)², induced drag = 10 kN × (200/V)²:
IAS Parasite Induced Total Parasite share 100 kt 2.5 kN 40.0 kN 42.5 kN 6 % 150 kt 5.6 kN 17.8 kN 23.4 kN 24 % 200 kt (VMD ) 10.0 kN 10.0 kN 20.0 kN (minimum) 50 % 250 kt 15.6 kN 6.4 kN 22.0 kN 71 % 300 kt 22.5 kN 4.4 kN 26.9 kN 84 % 350 kt 30.6 kN 3.3 kN 33.9 kN 90 %
D = aV² + b/V² is least when aV² = b/V²: the product of the two drags is constant, so their sum is smallest when they are equal.
Chapter 9 · Total Drag, Power and Speed Stability
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us check it with numbers. In our model, parasite drag is ten kilonewtons at two hundred knots and scales with the square of the speed; induced drag is also ten kilonewtons at two hundred knots and scales with one over the square. At one hundred knots: two and a half plus forty, forty-two and a half kilonewtons. At one hundred and fifty: about twenty-three point four. At two hundred: ten plus ten, twenty, the minimum. At two hundred and fifty: about twenty-two. At three hundred: almost twenty-seven. Notice the curve is quite flat near the bottom but rises steeply on the slow side. Why is the minimum exactly where the two are equal? Multiply the two drags together and the speed cancels out: their product is always the same. And when two quantities have a fixed product, their sum is smallest when they are equal. Watch the last column too: the parasite share climbs from six per cent to ninety per cent.
Who dominates where
The share of parasite and induced drag At VMD : exactly half parasite, half induced Just above the stall (≈ 0.76 VMD ): parasite only about 25 % ; induced is ¾ of the total At low speed induced drag is more than half the total At maximum level speed parasite drag is very nearly 100 % So streamlining pays at high speed; aspect ratio pays at low speed 0.5 0.76 1 1.5 2 25 50 75 100 IAS ÷ VMD parasite share of total drag (%) 25 % 50 % 94 % induced parasite share of parasite drag = V⁴ / (V⁴ + VMD ⁴)
Chapter 9 · Total Drag, Power and Speed Stability
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph shows the share of the total drag that is parasite drag, at speeds from half V M D to twice V M D. At V M D itself, the split is exactly fifty-fifty. Go slower, and induced drag takes over: at about nought point seven six of V M D, which is typically just above the stalling speed, parasite drag is only about a quarter of the total and induced drag is three quarters. Go faster, and parasite drag takes over: at twice V M D it is about ninety-four per cent, and at the maximum level flight speed it is very nearly all of the drag. This tells designers where to spend their effort. For high-speed performance, aerodynamic cleanliness and streamlining matter most. For low-speed performance, such as take-off, climb and the approach, it is the induced drag, and therefore the aspect ratio and the wing design, that matters.
VMD and L/D max
Minimum drag means the best lift to drag ratio In level flight lift = weight, so least drag means the highest L/D VMD is flown at the L/D max angle of attack , typically about 4° L/D max is the measure of aerodynamic efficiency Any other α, slower or faster, needs more drag for the same lift VMD is the reference for range, endurance, climb, glide and more lift drag (× 3 scale) α = 4° L/D ≈ 16.7 lift drag (× 3 scale) α = 11° L/D ≈ 12.7 drawn with the drag arrow three times enlarged
Chapter 9 · Total Drag, Power and Speed Stability
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because lift equals weight in level flight, the speed with the least drag is also the speed with the highest ratio of lift to drag. So flying at V M D means flying at the angle of attack for the maximum lift to drag ratio, which on a typical aircraft is about four degrees. The lift to drag ratio is the measure of the aerodynamic efficiency of the aircraft, and L slash D max is its best value. In the animation, at about four degrees the drag arrow is tiny compared with the lift arrow. Raise the angle of attack and the lift grows, but the drag grows much faster. Any angle of attack other than the L slash D max angle needs more drag, and so more thrust, for the same lift. That is why V M D is the reference speed for range, endurance, climb, glide, and much more.
L/D and angle of attack
L/D rises to a peak, then falls 0 4 8 12 0.4 0.8 1.2 α (°) CL 0.05 0.10 0.15 CL CD CD CL grows steadily; C D grows ever faster 0 4 8 12 5 10 15 20 α (°) L/D L/D max ≈ 16.7 at ≈ 4° the best angle of attack: VMD in level flight L/D max occurs at one particular angle of attack . If the IAS is changed in level flight, the α changes and so does L/D.
Chapter 9 · Total Drag, Power and Speed Stability
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is where the peak comes from. On the left, the lift coefficient rises steadily with angle of attack, up to the stall. The drag coefficient rises too, but ever more quickly, because induced drag grows with the square of the lift coefficient. Divide one by the other and you get the lift to drag ratio, on the right. At small angles of attack, lift is small compared with the parasite drag, so the ratio is poor. As the angle increases, lift grows faster than drag and the ratio climbs. Then induced drag catches up, and beyond the peak the ratio falls away. In our example the peak is about sixteen point seven at about four degrees. Two points matter for the exam. L slash D max occurs at one specific angle of attack. And because in level flight each IAS needs its own angle of attack, if you change the IAS, the lift to drag ratio changes too.
The drag polar
Reading L/D max from the polar 0.04 0.08 0.12 0.16 0.40 0.80 1.20 CD CL A low CL : high speed B tangent from the origin: L/D max C CL max : critical α (stall) Each point on the polar is one angle of attack. L/D at a point = CL / C D , the slope of a line from the origin. The steepest such line just touches the curve: that point is L/D max. Here: CL ≈ 0.60, C D ≈ 0.036, L/D max ≈ 16.7 at α ≈ 4° Draw a straight line from the origin that just touches the polar: the touching point is L/D max .
Chapter 9 · Total Drag, Power and Speed Stability
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Another common way of showing the same information is the drag polar: the lift coefficient of the whole aircraft plotted against its drag coefficient. Each point on the curve is one angle of attack. At first the lift coefficient climbs much more quickly than the drag coefficient, but eventually the drag coefficient increases faster. The lift to drag ratio at any point is the lift coefficient divided by the drag coefficient, which is the slope of a straight line from the origin to that point. So to find L slash D max, draw the steepest line from the origin that still touches the curve: the tangent. The touching point, B, is L slash D max. Point A, low on the curve, is a small angle of attack and high speed; point C, at the top, is the maximum lift coefficient at the critical angle of attack. Learn to recognise this diagram; it appears often in exams.
Exam facts
What changes L/D max, and what does not Fixed angle of attack L/D max always occurs at the same α (about 4°) for a given configuration.
Weight Changes VMD , but not the value of L/D max.
IAS The best L/D stays the same; but flying at another IAS gives a lower L/D.
Wind A headwind or tailwind does not change L/D: it is set by the air, not the ground.
Configuration Gear, flaps, speed brakes and contamination lower L/D max.
Any other α Gives more total drag for the same lift: more thrust, more fuel.
Chapter 9 · Total Drag, Power and Speed Stability
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the facts about L slash D max that examiners like to test. First, it always occurs at the same angle of attack for a given configuration, about four degrees in our example. Second, changing the weight changes the speed at which you reach that angle, V M D, but not the value of L slash D max itself. Third, the best L slash D of an aircraft in a given configuration stays the same regardless of the IAS; but if you fly at an IAS other than V M D, you are at a different angle of attack and get a lower ratio. Fourth, wind makes no difference: an aircraft with an L slash D of fifteen to one in calm air still has fifteen to one in a twenty-five knot headwind, because lift and drag depend on the air, not the ground. Finally, gear, flaps, speed brakes and contamination reduce it, and any other angle means more drag for the same lift.
Angle of attack and speed
In level flight, α sets the speed and the drag Lift = weight: a higher α needs a lower IAS , and the reverse So by changing α the pilot controls lift, airspeed and drag From VMD , raising α (slower) increases drag: induced drag grows Accelerating from CL max to maximum speed, drag first decreases , then increases Above VMD , drag rises because of parasite drag 150 200 250 300 350 10 20 30 40 IAS (kt) total drag (kN) α ≈ 10.3° α ≈ 8.4° α ≈ 4° α ≈ 0.7° α ≈ 0° drag falls then rises One weight, level flight: each angle of attack gives one IAS and one drag
Chapter 9 · Total Drag, Power and Speed Stability
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
In level flight, lift must equal weight, so every angle of attack goes with one particular IAS. A higher angle of attack needs a lower IAS, and a lower angle needs a higher IAS. That means that by changing the angle of attack, the pilot is really controlling the lift, the airspeed and the drag together. The graph marks the angle of attack along our drag curve: about ten degrees at one hundred and forty knots, eight degrees at one hundred and fifty-two, four degrees at V M D, and under one degree at three hundred knots. Now imagine accelerating in level flight from the maximum lift coefficient right up to maximum speed. The drag first decreases, as induced drag falls away, reaches its minimum at V M D, and then increases as parasite drag takes over. Below V M D, the extra drag comes from induced drag; above V M D, it comes from parasite drag.
Effect of weight
Lighter: less drag, and a lower VMD 100 150 200 250 300 350 10 20 30 40 IAS (kt) drag (kN) 200 179 heavier lighter Weight 20 % lower Induced drag × 0.8² = × 0.64 VMD × √0.8 ≈ × 0.89 Minimum drag × 0.8 (16 kN) Parasite drag unchanged at a given IAS L/D max unchanged (same α) Dmin = W ÷ (L/D) max Heavier, or manoeuvring at a higher load factor: more induced drag , more total drag , higher VMD .
Chapter 9 · Total Drag, Power and Speed Stability
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Weight acts on the induced drag only. As fuel is burned, the aircraft gets lighter, less lift is needed, the lift coefficient is lower, and induced drag falls. Parasite drag at a given IAS is unchanged. So the whole total drag curve moves down and to the left: total drag is less and V M D occurs at a lower IAS. In our example, twenty per cent lighter means induced drag times nought point eight squared, nought point six four. V M D falls with the square root of the weight, to about one hundred and seventy-nine knots, and the minimum drag falls in proportion to the weight, from twenty to sixteen kilonewtons. The L slash D max value is unchanged; we simply reach it at a lower speed. The reverse is true for a heavier aircraft, or one manoeuvring with a load factor above one: more induced drag, more total drag, and a higher V M D. Notice that weight increases induced drag much more than parasite drag.
Effect of altitude
At constant IAS, drag does not change with altitude Aircraft are flown by IAS , and IAS measures dynamic pressure ½ρV² At constant IAS , Q is constant, so drag is the same at any altitude VMD is an IAS : the same IAS at every altitudeBut the TAS for that IAS rises as density falls At a fixed TAS , higher density means more lift and drag 100 200 300 400 IAS (kt) drag sea level and altitude: one curve 100 200 300 400 TAS (kt) drag sea level altitude (σ = 0.5) VMD TAS × 1.41
Chapter 9 · Total Drag, Power and Speed Stability
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aircraft are flown by indicated airspeed, so it makes sense to plot drag against IAS. IAS is really a measure of dynamic pressure, half rho V squared. If you fly at a constant IAS, the dynamic pressure is constant, so both parasite and induced drag are the same as at sea level. The drag against IAS curve is therefore the same curve at every altitude, ignoring compressibility, and V M D is the same IAS everywhere. What does change is the true airspeed. As density falls with height, a higher TAS is needed to give the same IAS. At a height where the density is half the sea level value, the TAS is about one point four one times the IAS. So the drag against TAS curve slides to the right, with the same minimum drag but at a higher true airspeed. And the reverse view is a classic exam question: at a fixed true airspeed, denser air gives more lift and more drag.
Effect of configuration
Gear, flaps and speed brakes: more drag, lower VMD 100 150 200 250 300 350 10 20 30 40 IAS (kt) drag (kN) 200 173 gear, flaps, speed brakes clean Parasite drag × 1.8 Parasite drag × 1.8 at every IAS Induced drag about the same Total drag higher at every IAS VMD × 1.8−¼ ≈ × 0.86 Minimum drag × √1.8 ≈ × 1.34 more drag, but a lower VMD Extra parasite drag raises the curve on the high-speed side , so the minimum moves to a lower IAS.
Chapter 9 · Total Drag, Power and Speed Stability
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now configuration. Lowering the landing gear, the flaps or the speed brakes increases parasite drag but does not substantially change induced drag. The result looks a little surprising. Total drag is higher at every IAS, but V M D is lower than for the clean aircraft. Why lower? Because the extra parasite drag pushes up the high-speed side of the curve much more than the low-speed side, so the bottom of the U moves to the left. In our example, with parasite drag increased by eighty per cent, V M D falls by about fourteen per cent, from two hundred to about one hundred and seventy-three knots, while the minimum drag rises by about a third. Compare this with weight: more weight raises V M D, but more parasite drag lowers it. Keep those two the right way round. This lower V M D with gear and flaps out turns out to be very useful on the approach, as we will see shortly.
Speed stability 1
Drag is the thrust required Steady flight means equilibrium : no unbalanced forces or moments Trimmed at a steady speed, thrust = drag So the drag curve is also the thrust required curve The thrust the engines give at a fixed throttle is the thrust available If speed changes with the throttle fixed: thrust excess or thrust deficiency LIFT WEIGHT THRUST DRAG steady flight: L = W and T = D
Chapter 9 · Total Drag, Power and Speed Stability
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
To understand speed stability we need one more idea. For steady flight, the aircraft must be in equilibrium, with no unbalanced forces or moments. When it is trimmed at a steady speed, thrust equals drag. So in steady flight, drag and thrust required mean the same thing, and we can relabel the drag curve as the thrust required curve. The thrust the engines are actually giving at a fixed throttle setting is called the thrust available. Now, suppose the speed changes slightly while the throttle stays where it is. Depending on where on the curve the aircraft was trimmed, there will be either more thrust available than is required, a thrust excess, which accelerates the aircraft, or less thrust available than required, a thrust deficiency, which slows it down. Which one you get decides whether the speed returns to where it was or runs away.
Speed stability 2
The front and the back of the drag curve 137 200 292 10 20 26 30 40 IAS (kt) drag = thrust required (kN) B A thrust available (fixed throttle) thrust excess thrust deficiency thrust deficiency SPEED UNSTABLE NEUTRAL SPEED STABLE VMD With a fixed throttle, thrust available crosses the drag curve at A (above VMD , stable ) and B (below VMD , unstable ).
Chapter 9 · Total Drag, Power and Speed Stability
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the drag, or thrust required, curve with a fixed throttle setting drawn across it as the blue thrust available line. It crosses the curve at two points, and the aircraft could be trimmed at either. Point A is above V M D, on what pilots call the front of the drag curve. Point B is below V M D, on the back of the drag curve. Between B and A, the thrust available is greater than the drag, a thrust excess, shaded green. Below B and above A, the drag is greater, a thrust deficiency. Close to V M D the curve is so flat that a small change of speed hardly changes the drag at all, so there is a neutral region, with no strong tendency either way. Now we will disturb the aircraft at each point and see what happens.
Speed stability 3
Stable above VMD , unstable below Stability : the tendency to return to the original condition after a disturbanceAt A : faster → thrust deficiency → slows back; slower → thrust excess → speeds back: speed stable At B : slower → more drag → slows further; faster → less drag → keeps accelerating: speed unstable Below VMD a speed loss feeds itself Near VMD : neutral , no strong tendency either way Trimmed at A (above VMD ): stable trim time → faster slower Trimmed at B (below VMD ): unstable trim time → keeps slowing accelerates away faster slower
Chapter 9 · Total Drag, Power and Speed Stability
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Stability means the tendency to return to the original condition after a disturbance. At point A, above V M D, suppose a gust makes the aircraft slightly faster. Drag rises above the thrust available, a thrust deficiency, so the aircraft slows back to A. If it is disturbed slower, drag falls below thrust, a thrust excess, and it speeds back up to A. Either way it returns: the aircraft is speed stable. At point B, below V M D, the opposite happens. Disturbed slower, the drag increases, so there is a thrust deficiency and the aircraft slows even more, and the further it slows the worse it gets. Disturbed faster, drag decreases, giving a thrust excess, so the aircraft keeps accelerating away from B, through V M D, until thrust and drag balance again on the stable side. Either way, the disturbance grows: the aircraft is speed unstable. Close to V M D, it is neutral.
Speed stability 4
On the approach: the back of the drag curve Approach speeds are often at or below VMD : speed unstable A small speed loss grows unless the pilot acts Monitor IAS closely; counter any slowing with a generous thrust increase Gear and flaps lower VMD , moving the stable region left Autothrottle helps hold speed on the back of the curve 3° glide path Approach: at or below VMD flaps and gear lower VMD ; watch the IAS, be generous with thrust
Chapter 9 · Total Drag, Power and Speed Stability
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Speed stability matters most during the approach to land, because approach speeds are often at or below V M D, on the back of the drag curve. There, if the aircraft starts to slow down, the drag increases and it slows further, and the pilot must catch it quickly. That is why you must monitor the IAS very closely on the approach, and counter any tendency to slow down at once with a generous increase in thrust, enough to get back to the target speed, not just to stop the decrease. Configuration helps here. Lowering the gear and flaps adds parasite drag, and as we saw, that lowers V M D, moving the speed-stable region to the left so that more of the approach speed range is stable. In the animation, the flaps and gear come out and the aircraft settles nose-up on the approach. Many aircraft also use an autothrottle to hold the speed.
Power required 1
Power required = drag × TAS Thrust is a force; power is the rate of doing work Work = force × distance, so power = force × distance ÷ time = force × speed The force is drag ; the speed is the speed through the air, TAS Power required = drag × TAS Climbing at constant IAS: drag constant, TAS rises, power required rises Link power with rate : least power gives the least rate of descent in a glide POWER = WORK ÷ TIME work = force × distance so power = force × distance ÷ time POWER REQUIRED = DRAG × TAS Example at sea level (TAS = IAS): drag 20 kN at 200 kt (≈ 102.9 m/s) P = 20 kN × 102.9 m/s ≈ 2060 kW Climb at constant IAS: drag unchanged, TAS rises → power required rises
Chapter 9 · Total Drag, Power and Speed Stability
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now let us turn drag into power. Thrust is a force, a push or a pull, used to oppose drag. Power is something different: it is the rate of doing work. Work is force times distance, so power is force times distance divided by time, and distance divided by time is a speed. For the power required by the airframe, the force is the drag, and the speed is the only speed there is, the speed of the aircraft through the air, the true airspeed. So power required equals drag times TAS. For example, twenty kilonewtons of drag at two hundred knots, about one hundred and three metres per second, needs about two thousand and sixty kilowatts. If you climb at a constant IAS, the drag stays the same, but the TAS increases, so the power required increases. A useful memory aid: associate power with rate. The minimum rate of descent in a glide, for example, comes at the minimum power speed.
Power required 2
The power required curve and VMP 100 152 200 250 300 350 1000 2000 3000 4000 5000 TAS (kt) at sea level power required (kW) VMP ≈ 152 kt, ≈ 1810 kW VMD = 200 kt: tangent from origin power required drag (scaled) P = D × TAS VMP = V MD ÷ ⁴√3 ≈ 0.76 VMD VMD ≈ 1.32 V MP At VMP : induced is ¾ of total drag VMP is slower than VMD . The tangent from the origin touches the power curve at VMD , where TAS per unit power is greatest (VMD ≈ 1.32 VMP ).
Chapter 9 · Total Drag, Power and Speed Stability
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
To draw the power required curve, multiply each drag value by its true airspeed. This graph is for one weight, in level flight at sea level, where true airspeed equals indicated airspeed. Because each drag value is multiplied by its speed, the high-speed side is pushed up much more than the low-speed side, so the bottom of the power curve moves to a lower speed than the bottom of the drag curve. That bottom is the minimum power speed, V M P, and like V M D it is quoted as an IAS. In our example, V M P is about one hundred and fifty-two knots, while V M D is two hundred. V M P is always slower than V M D; in fact V M D is about one point three two times V M P. And a line from the origin just touches the power curve at V M D, where you get the most speed for each kilowatt.
Power required 3
VMP and VMD compared VMP (minimum power) VMD (minimum drag) Minimum of Power required = drag × TAS Drag = thrust required Relative speed Slower: about 0.76 VMD Faster: about 1.32 VMP Drag split Induced ≈ ¾, parasite ≈ ¼ Induced = parasite Speed stability On the back of the drag curve: unstable Edge of the stable region: neutral In a glide Least rate of descentLeast angle of descent (best glide range)On the power curve Lowest point Where the tangent from the origin touches: max TAS / power With altitude Same IAS; higher TAS Same IAS; higher TAS
Power goes with rate ; drag goes with angle . The details of glide, climb, range and endurance come in later lessons.
Chapter 9 · Total Drag, Power and Speed Stability
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us compare the two speeds side by side. V M P is the minimum of the power required curve; V M D is the minimum of the drag curve. V M P is the slower of the two, about nought point seven six of V M D, or put the other way, V M D is about one point three two times V M P. V M P is on the back of the drag curve, so it is speed unstable, while V M D sits at the edge of the stable region. In a glide, flying at V M P gives the least rate of descent, so the longest time in the air, while V M D gives the least angle of descent, so the greatest distance. On the power curve, V M P is the lowest point, while V M D is where the tangent from the origin touches. Both are indicated airspeeds.
Power required 4
Power required at altitude 100 200 300 400 500 2000 4000 6000 TAS (kt) power required (kW) sea level altitude, σ = 0.5 VMD : same IAS, TAS × 1.41 VMP each point moves out along a line from the origin At altitude, the same IAS needs the same drag but a higher TAS , so more power . VMP and VMD stay the same IAS, and VMP stays slower than VMD .
Chapter 9 · Total Drag, Power and Speed Stability
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
What happens to power required at altitude? At a given IAS the drag is the same as at sea level, but the true airspeed is higher. Where the density is half the sea level value, the TAS is about one point four one times the IAS. Power is drag times TAS, so the power required is also one point four one times as much. Every point on the sea level curve therefore moves outwards, along a line from the origin, by the same factor: the altitude curve sits higher and further to the right. So the tangent from the origin still touches at V M D, and the ratio of TAS to power required at V M D is unaffected, V M P and V M D are still the same indicated airspeeds, and V M P remains slower than V M D. What you need at altitude is more power to fly at those speeds.
Exam focus
Total drag traps Below VMD Slower than L/D max speed: drag increases , because of induced drag.
Above VMD Faster: drag increases , because of parasite drag.
Weight vs flaps More weight: VMD up . More parasite drag: VMD down . Both: more drag.
L/D max When parasite = induced. Same α; unaffected by weight, IAS or wind.
Speed stability Stable above VMD ; unstable below : slowing feeds itself.
Power P = D × TAS . VMP < VMD ; VMD ≈ 1.32 VMP .
Chapter 9 · Total Drag, Power and Speed Stability
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the traps that catch people on total drag. One: if the speed falls below the speed for L slash D max, total drag increases, and the reason is induced drag, not parasite drag. Two: if the speed rises above V M D, total drag increases because of parasite drag. Three: weight and configuration move V M D in opposite directions. More weight raises V M D; more parasite drag from gear, flaps or speed brakes lowers it; but both increase the drag. Four: the best lift to drag ratio occurs where parasite drag equals induced drag, always at the same angle of attack, and its value is not changed by weight, IAS or wind. Five: an aircraft is speed stable above V M D and speed unstable below it. Six: power required is drag times true airspeed, and V M P is slower than V M D, with V M D about one point three two times V M P.
Summary
Total drag in one page Total drag Parasite + induced. U-shaped against IAS; minimum at VMD .
VMD Where parasite = induced ; L/D max at about 4°.
Polar Tangent from the origin touches at L/D max .
Weight Lighter: less drag, lower VMD . Heavier or more g: higher.
Altitude Constant IAS: same drag , same VMD IAS; TAS higher.
Configuration Gear, flaps, brakes: more drag, lower VMD .
Speed stability Above VMD stable ; below unstable ; near VMD neutral.
Power P = D × TAS. VMP ≈ 0.76 VMD ; power ↔ rate.
Chapter 9 · Total Drag, Power and Speed Stability
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us wrap up the three drag lessons. Total drag is parasite drag plus induced drag, a U-shaped curve against IAS, with its minimum at V M D, where parasite and induced drag are equal and the aircraft is at the L slash D max angle of attack, about four degrees. On a drag polar, the tangent from the origin finds L slash D max. A lighter aircraft has less induced drag, less total drag and a lower V M D; a heavier one or one pulling g, the reverse. At constant IAS, altitude does not change the drag or V M D, but the true airspeed is higher. Gear, flaps and speed brakes increase drag but lower V M D. Above V M D the aircraft is speed stable; below it, speed unstable, so watch the speed on the approach. And power required is drag times TAS, with its minimum at V M P, about three quarters of V M D. Well done: that completes drag.