Principles of Flight · Chapter 22
Turning Flight and Load Factor What makes an aircraft turn, why a turn needs more lift, how load factor and stall speed rise with bank, and how speed and bank set the radius and rate of turn.
centre of turn Lift Weight centripetal force © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to turning flight. To fly round a corner an aircraft needs a force pushing it towards the centre of the turn, and the only force available is lift, tilted over by banking. That simple idea explains everything in this lesson: why you must pull back in a turn, why the load factor and the stalling speed rise as you bank, and how your speed and bank angle together fix the radius and the rate of turn. We finish with the turn co-ordinator and the difference between slipping and skidding.
Roadmap
Turning: one tilted lift vector explains it all Straight · 0° · n = 1.00 Gentle · 20° · n = 1.06 Medium · 45° · n = 1.41 Steep · 60° · n = 2.00 Forces Lift tilted by bank: L cos φ = W , L sin φ turns the aircraft.
Load factor n = 1/cos φ ; the stall speed rises by √n .
Radius and rate r = V²/(g tan φ) ; ω = V/r ; rate 1 = 3°/s.
Limits and balance Stall, strength, thrust; slips and skids on the ball.
Chapter 22 · Turning Flight and Load Factor
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson is all about one picture: an aircraft banked over, with its lift vector tilted towards the centre of the turn. From that picture we get everything. First, the forces: the vertical part of lift holds up the weight, and the horizontal part pulls the aircraft round. Second, the load factor: because only part of the lift supports the weight, the wing must make more lift, so the load factor and the stalling speed rise with bank. Third, the geometry: speed and bank together fix the radius and the rate of turn, and we will calculate them. Last, the limits on how tight you can turn, and how to keep the turn balanced using the turn co-ordinator and its ball. The panels above show the load factor at four bank angles; look how fast it grows beyond forty-five degrees.
Why an aircraft turns
A turn needs a force towards the centre To change direction a body needs a centripetal force towards the centre of the turn Banking tilts the lift ; its horizontal component is the centripetal force The rudder does not turn the aircraft: it only keeps the turn balanced The required force is W V² / (g r) : more speed or a tighter radius needs more "Centrifugal force" is just the inertia felt by the occupants, not a real outside force centre of turn centripetal force velocity (tangent) Plan view: a turn needs a force towards the centre It comes from the horizontal component of lift
Chapter 22 · Turning Flight and Load Factor
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Anything moving in a circle is constantly changing direction, and to do that it needs a force pointing towards the centre of the circle. We call it the centripetal force. In an aircraft, that force comes from lift. When you bank, you tilt the lift vector, and its horizontal component pulls the aircraft round towards the centre of the turn. Notice that it is the bank, not the rudder, that turns an aeroplane; the rudder only keeps the turn balanced. The force needed is the weight times the speed squared, divided by g times the radius, so a faster turn or a tighter turn needs more of it. You will sometimes hear about centrifugal force pressing you into your seat. That is really just your own inertia, your body trying to carry straight on, and it is not an outside force acting on the aircraft.
Forces in a level turn
The level-turn equations Vertical: L cos φ = W keeps the turn level Horizontal: L sin φ = W V² / (g r) is the centripetal force Divide one by the other: tan φ = V² / (g r) Know any two of V, r and φ and you can find the third Use TAS in m/s, r in metres, g = 9.81 m/s² L L cos φ = W L sin φ = WV²/gr W φ Rear view, level turn to the right Divide: tan φ = V² / (g r) V = TAS (m/s), r in m, g = 9.81 m/s²
Chapter 22 · Turning Flight and Load Factor
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us write the balance of forces in a steady level turn, with a bank angle we call phi. Vertically, the upward component of lift, L cos phi, must equal the weight, otherwise the aircraft climbs or descends. Horizontally, the component L sin phi must supply the centripetal force, which is the weight times V squared divided by g times r. Now divide the second equation by the first. Lift cancels, weight cancels, and you are left with tan phi equals V squared over g r. That is the basic turning equation, and it ties together just three things: the true airspeed, the radius and the bank angle. If you know any two, you can work out the third. Be careful with units: V must be the true airspeed in metres per second, the radius in metres, and g is nine point eight one metres per second squared.
Holding height
Bank alone is not enough: pull back for more lift Bank at a constant α: lift is unchanged, its vertical part falls short of W → the aircraft descends To hold height, increase α (back pressure) so L cos φ = W again At 30° bank: L must be 1.155 W ; at 60°: 2 W More α means more induced drag , so more thrust is needed The extra lift is felt as load factor Bank only: L = W vertical lift < W descends Pull back: L = 1.155 W vertical lift = W height held (dotted line = weight to support)
Chapter 22 · Turning Flight and Load Factor
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Suppose you roll into a bank but keep the same angle of attack. The total lift is unchanged, but now it is tilted, so its vertical component is smaller than the weight, and the aircraft starts to descend. Watch the arrows. As the aircraft banks, the lift tilts over with the wings, and its vertical part no longer matches the weight. To hold your height you must increase the angle of attack with back pressure on the control column, so the total lift grows until its vertical component equals the weight again. At thirty degrees of bank the lift must be one point one five five times the weight; at sixty degrees it must be twice the weight. That extra lift brings extra induced drag, so you also need more thrust. And everyone on board feels the extra lift as an increased load factor.
Load factor
n = 1 / cos φ: it depends only on bank bank angle φ → load factor n 0° 10° 20° 30° 40° 50° 60° 70° 1 2 3 4 5 6 30°: 1.15 45°: 1.41 60°: 2.0 66°: 2.5 (jet limit) 75.5°: 4.0 n = L / W = 1 / cos φ Depends ONLY on bank angle Rises at an increasing rate Two aircraft of different weight at the same bank have the same load factor . It rises at an increasing rate: 60° doubles it.
Chapter 22 · Turning Flight and Load Factor
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Load factor, n, is lift divided by weight. In a level turn, lift times cos phi equals weight, so n equals one over cos phi. That is a remarkable result: in a level, balanced turn the load factor depends only on the bank angle. It does not depend on speed, weight or aircraft type, so two aircraft of different weight at the same bank have exactly the same g. The curve rises slowly at first: thirty degrees gives one point one five, forty-five degrees one point four one. Then it climbs steeply. Sixty degrees gives two g, about sixty-six degrees gives two and a half, which is the limit load factor of a typical jet transport, and seventy-five and a half degrees gives four. So the load factor increases with bank at an increasing rate, not in proportion to the bank. That is a favourite exam question.
Numbers to know
Bank, load factor and stall speed Bank φ Load factor n = 1/cos φ Extra lift needed Stall factor √n VS if level VS = 70 kt 0° 1.00 0% 1.00 70 kt 15° 1.04 +4% 1.02 71 kt 30° 1.15 +15% 1.07 75 kt 45° 1.41 +41% 1.19 83 kt 60° 2.00 +100% 1.41 99 kt 66.4° 2.50 (jet limit) +150% 1.58 111 kt 75.5° 4.00 +300% 2.00 140 kt
Learn 30°, 45° and 60°. A 60° balanced turn means 2 g and a stalling speed about 40% higher .
Chapter 22 · Turning Flight and Load Factor
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the numbers worth memorising. At fifteen degrees of bank the load factor is only one point zero four. At thirty degrees it is one point one five, meaning fifteen per cent more lift than in level flight. At forty-five degrees it is one point four one. At sixty degrees it is exactly two, double the lift. The stalling speed goes up with the square root of the load factor, so the stall factor at sixty degrees is the square root of two, one point four one. If the level-flight stalling speed is seventy knots, the stall comes at about seventy-five knots in a thirty degree turn, eighty-three knots at forty-five degrees and ninety-nine knots at sixty degrees. At the jet transport limit of two and a half g, the stall speed is up by about fifty-eight per cent, and at four g it doubles.
A steep turn
60° of bank: twice the lift, twice the g At 60° only half the lift is vertical, so lift must be 2 W Load factor 2 : everything on board weighs twice as much The horizontal part, L sin 60° = 1.73 W , gives a tight turn Stall speed up by √2 ≈ 41% ; induced drag about ×4 Demanding: big back pressure, plenty of power, a close eye on speed L = 2 W L cos 60° = W W L sin 60° = 1.73 W n = 1 / cos 60° = 2 every kilogram feels twice as heavy VS × √2 = VS × 1.41 induced drag × 4 at the same IAS
Chapter 22 · Turning Flight and Load Factor
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look closely at the classic steep turn. We start level and roll in, first to thirty degrees and then on to sixty. At sixty degrees the cosine is one half, so only half of the lift acts vertically. To hold height the wing must therefore make twice the weight in lift, and the load factor is two. Everything on board, including you, feels twice as heavy. The horizontal part of lift is the lift times sine sixty, about one point seven three times the weight, which gives a tight, quick turn. But the costs are large. The stalling speed rises by the square root of two, about forty-one per cent, and at the same airspeed the induced drag is about four times as big, so you need a lot of back pressure, plenty of power and a close eye on the airspeed.
Stall speed in a turn
The stalling speed rises with the square root of n The wing stalls at the same CL max (same angle of attack) in a turn n times the lift at CL max needs √n times the speed VS turn = VS × √n Example: VS 70 kt, 60° bank → 70 × 1.414 = 99 kt Hard pull in a steep turn: you can stall well above the published VS 70 kt 0° ×1.000 75 kt 30° ×1.075 83 kt 45° ×1.189 99 kt 60° ×1.414 VS in a turn = VS × √n level-flight VS = 70 kt
Chapter 22 · Turning Flight and Load Factor
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does the stalling speed rise in a turn? The wing still stalls at the same angle of attack, the same maximum lift coefficient. But in a turn it must produce n times the weight in lift. Lift goes with the square of the speed, so to get n times the lift at the same maximum lift coefficient you need the square root of n times the speed. So the stalling speed in a turn equals the level stalling speed times the square root of the load factor. Worked example: an aircraft stalls at seventy knots in level flight. In a sixty degree balanced turn the load factor is two, the square root of two is one point four one four, and seventy times one point four one four is about ninety-nine knots. This is why steep turns close to the ground, at low speed, are so dangerous: the aircraft can stall at a speed that would be perfectly safe with the wings level.
Turn radius and rate
r = V² / (g tan φ) and ω = V / r Radius r = V² / (g tan φ) : grows with the square of TASRate of turn ω = V / r = g tan φ / V (rad/s)Example: 150 kt, 30° → r ≈ 1 050 m , ω ≈ 4.2°/s Rate is directly ∝ TAS and inversely ∝ radius One radian = 57.3° r V (TAS) ω = V / r r = V² / (g tan φ) ω = g tan φ / V (rad/s; × 57.3 for °/s) Worked example 150 kt TAS = 77.2 m/s, φ = 30°, tan φ = 0.577 r = 77.2² ÷ (9.81 × 0.577) ≈ 1 050 m (0.57 nm) ω = 77.2 ÷ 1 050 ≈ 0.0734 rad/s ≈ 4.2°/s → 360° in about 86 s
Chapter 22 · Turning Flight and Load Factor
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Rearranging the turning equation gives the turn radius: r equals V squared over g tan phi. The radius grows with the square of the true airspeed. The rate of turn, the angular velocity, is the speed divided by the radius, which works out as g tan phi divided by V, in radians per second. Let us try one. At a hundred and fifty knots true airspeed, which is seventy-seven point two metres per second, and thirty degrees of bank, tan thirty is nought point five seven seven. The radius is seventy-seven point two squared, divided by nine point eight one times nought point five seven seven, about one thousand and fifty metres. The rate is seventy-seven point two divided by one thousand and fifty, about nought point nought seven three radians per second. Multiply by fifty-seven point three to get degrees: about four point two degrees per second, so a full circle takes about eighty-six seconds.
Rate one turns
Rate 1 = 3°/s: the bank needed depends on TAS Rate 1 : 3°/s, 180°/min, 360° in 2 min. Rate 2 : 6°/sFrom ω = g tan φ / V: tan φ = ω V / g Constant rate + more speed → more bank 120 kt → about 18° ; 250 kt → about 34.5° Rule of thumb: φ ≈ TAS/10 + 7 Check: 77 m/s on a 1 480 m radius → 0.052 rad/s ≈ 3°/s TAS (kt) → bank for rate 1 100 150 200 250 300 10° 20° 30° 40° 120 kt: 18.2° 250 kt: 34.5° exact: tan φ = ω V / g rule of thumb: φ ≈ TAS/10 + 7 Rate 1 = 3°/s = 180°/min · 360° in 2 minutes
Chapter 22 · Turning Flight and Load Factor
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Instrument flying uses standard rates of turn. A rate one turn is three degrees per second, a hundred and eighty degrees a minute, so a full circle takes two minutes. Rate two is six degrees per second. From the rate equation, tan phi equals the rate in radians per second times the speed, divided by g. So for a constant rate of turn, a faster aircraft needs more bank. At a hundred and twenty knots, a rate one turn needs about eighteen degrees; at two hundred and fifty knots, about thirty-four and a half. A handy rule of thumb is a tenth of the true airspeed plus seven, which gives nineteen and thirty-two, close enough in the cockpit. As a check of the units: an aircraft at seventy-seven metres per second on a radius of one thousand four hundred and eighty metres turns at nought point nought five two radians per second, which times fifty-seven point three is three degrees per second, exactly rate one.
Speed and bank
Double the speed: four times the radius, half the rate Same bank (30°), speed doubled 120 kt: r ≈ 670 m 240 kt: r ≈ 2 690 m (×4) radius ×4, rate ÷2 (5.3 → 2.6°/s) Same speed (150 kt), steeper bank 20° 30° 45° 60° steeper bank: smaller radius, higher rate, more g Tighter, quicker turn: steepen the bank and/or slow down . Slowing down does it without extra load factor.
Chapter 22 · Turning Flight and Load Factor
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the effects of speed and bank, drawn to scale. On the left the bank is fixed at thirty degrees. At a hundred and twenty knots the radius is about six hundred and seventy metres. Double the speed to two hundred and forty knots and the radius becomes four times larger, about two thousand six hundred and ninety metres, because radius goes with speed squared. The rate of turn is speed divided by radius, so twice the speed over four times the radius gives half the rate. The load factor is unchanged, because the bank is unchanged. On the right the speed is fixed at a hundred and fifty knots, and the bank is steepened from twenty to sixty degrees; the circle shrinks and the rate rises, but the load factor climbs too. So to turn tighter and quicker, steepen the bank or slow down, and slowing down does it without any extra g.
Effect of weight
Same TAS and bank: same turn for any aircraft Heavier: more vertical lift needed, and more centripetal force for the same radius Both grow in the same proportion , so the lift has the same tilt Radius, rate and load factor depend only on TAS and bank Independent of weight, CG and aircraft type But a heavy aircraft may not reach the same bank at that TAS (stall, thrust) Light W L Heavy W L Same TAS and bank → same r, ω and n Lift and centripetal force both scale with W
Chapter 22 · Turning Flight and Load Factor
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Does weight change the turn? Suppose a heavier aircraft flies the same true airspeed at the same bank angle. It needs more vertical lift to support its weight, and it needs more centripetal force to follow the same radius, because the centripetal force is weight times V squared over g r. Both requirements grow in exactly the same proportion as the weight, so the total lift is larger but tilted at the same angle. The radius and rate come only from the true airspeed and the bank, and the load factor only from the bank. So a given TAS and bank produce the same radius, rate and load factor in any aeroplane, whatever its weight, CG or type. The catch is that a heavier aircraft has a higher stalling speed and needs more thrust, so it may not be able to reach that bank angle at that speed.
Any aeroplane
Turn radius against TAS for different banks TAS (kt) → turn radius (ft) 100 150 200 250 300 1000 2000 3000 4000 5000 6000 15° 20° 30° 45° 60° A r ∝ V² at a given bank Any aircraft, any weight: same TAS + bank = same turn A: 130 kt, 20° ≈ 4 100 ft, 3.1°/s 260 kt, 20°: ≈ 16 400 ft, 1.5°/s Because only TAS and bank matter, one chart works for every aircraft . 130 kt at 20° gives about 4 100 ft and 3°/s; at 260 kt, four times the radius and half the rate.
Chapter 22 · Turning Flight and Load Factor
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Since only true airspeed and bank angle matter, a single chart works for every aeroplane. Each curve is one bank angle, and each rises with the square of the speed, so the radius grows rapidly as you go faster. Steeper banks sit lower down, with smaller radii. Take the marked point: a hundred and thirty knots at twenty degrees of bank gives a radius of about four thousand one hundred feet, and a rate of about three degrees per second, practically a rate one turn. Now double the speed to two hundred and sixty knots at the same twenty degrees. The radius is four times larger, about sixteen thousand four hundred feet, and the rate halves to about one and a half degrees per second. This is why a jet on a radar vector needs much more airspace to turn than a light trainer at the same bank angle.
How tight can you turn?
Stall, strength and thrust limits on turning TAS (kt) → minimum turn radius (m) 120 160 200 240 280 320 250 500 750 1000 1250 VA ≈ 190 kt: minimum radius ≈ 420 m stall limit (CL max) strength limit 2.5 g thrust limit (example) VS (1 g) = 120 kt limit n = 2.5 VA = VS √2.5 Heavier → higher VS → larger min radius If thrust is adequate, the minimum radius is where the stall limit meets the strength limit: at VA . A heavier aircraft has a larger minimum radius.
Chapter 22 · Turning Flight and Load Factor
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three things limit how tightly you can turn. The strength limit: every aircraft has a limit load factor, two and a half g for a jet transport, reached at about sixty-six degrees of bank. At that load factor the radius grows with speed squared, so it sets the minimum radius at high speed. The stall limit: at a given speed, banking more needs more angle of attack, and eventually you reach the stalling angle. At low speed that comes first, and the radius it allows gets larger as the speed falls towards the one g stalling speed. The thrust limit: more lift means more induced drag, and eventually the throttles are fully open. If thrust is adequate, the smallest possible radius is where the stall limit meets the strength limit, and that speed is V A, the stalling speed times the square root of the limit load factor. Here, a hundred and twenty knots times root two point five, about a hundred and ninety knots.
Thrust in a turn
A level turn needs more thrust than level flight More lift → more induced drag At the same IAS, CL rises by n, so induced drag rises by about n² 60° bank at the same IAS: induced drag about ×4 More thrust, more power: the throttle must open Not because "thrust provides the centripetal force": lift does that ×1.00 0° ×1.33 30° ×2.00 45° ×4.00 60° parasite drag induced drag (∝ n² at the same IAS) Drag at the same IAS
Chapter 22 · Turning Flight and Load Factor
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a level turn at a constant indicated airspeed you need more power than in straight and level flight, and the reason is drag. To make n times the lift at the same airspeed, the lift coefficient must rise n times. Induced drag goes with the square of the lift coefficient, so induced drag rises by about n squared. At thirty degrees that is one third more induced drag; at forty-five degrees twice as much; at sixty degrees four times as much. Parasite drag, at the same airspeed, does not change. So the total drag rises and you must open the throttle to hold the speed. Be careful with the exam distractor that says more power is needed because some thrust is used to give the centripetal force. That is wrong. Lift provides the centripetal force; the extra thrust only pays for the extra induced drag.
Turn co-ordination
The turn co-ordinator and the ball Miniature aircraft shows rate of turn; wing on the index = rate 1 Ball (inclinometer) shows balance: centred = no sideslipSideslip comes from adverse yaw, torque, gyroscopic effects, asymmetric thrust and slipstream Keep the ball centred with rudder : "step on the ball" Exception: asymmetric thrust , covered in the next lesson L R 2 MIN Miniature aircraft: rate of turn (wing on index = rate 1) Ball (inclinometer): balance / sideslip Ball out of centre: "step on the ball"
Chapter 22 · Turning Flight and Load Factor
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Unco-ordinated flight means the aircraft is sideslipping, moving partly sideways through the air. Many things can cause it: adverse aileron yaw, engine torque, propeller gyroscopic effects, the spiral slipstream and asymmetric thrust. The pilot sees it on the turn co-ordinator. The miniature aircraft shows the rate of turn, and when its wing tip sits on the index mark, you are in a rate one turn. The ball in the curved glass tube is the inclinometer, and it shows balance. When the ball is centred between the reference lines, there is no sideslip. When it moves out, you correct with rudder on the same side as the ball. The rule is simply: step on the ball. Remember one exception, which we meet in the next lesson. With an engine failed on a twin, flying with zero sideslip leaves the ball slightly off centre.
Slips and skids
Balanced, slipping and skidding turns Balanced L R 2 MIN Ball centred no sideslip Slipping turn L R 2 MIN Ball to the INSIDE right rudder, or less bank Skidding turn L R 2 MIN Ball to the OUTSIDE left rudder, or more bank All three: turning right · rule "step on the ball" (rudder on the side the ball has gone) Slip : too much bank for the rate of turn, sliding inwards. Skid : too little bank for the rate of turn, sliding outwards.
Chapter 22 · Turning Flight and Load Factor
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are three right turns. On the left the turn is balanced: the ball is centred and there is no sideslip. In the middle is a slipping turn. The aircraft has too much bank for its rate of turn, so it slides sideways towards the inside of the turn, and the ball moves to the inside, to the right. Step on the ball: apply right rudder, or reduce the bank angle. On the right is a skidding turn. Here there is too much rate of turn for the bank, often from too much rudder in the direction of the turn, and the tail swings out so the aircraft slides towards the outside. The ball moves to the outside, the left. Correct it with left rudder, or more bank. So, for the exam, skidding outwards in a turn is caused by insufficient bank for the rate of turn.
Worked example
One turn, every number A jet flies a level, balanced turn at 200 kt TAS with 45° of bank. Its level-flight stalling speed is 110 kt .
Quantity Working Answer Load factor n = 1 / cos 45° = 1 / 0.707 1.41 g Stalling speed 110 × √1.414 = 110 × 1.189 ≈ 131 kt Speed in m/s 200 × 0.5144 102.9 m/s Radius 102.9² / (9.81 × tan 45°) = 10 588 / 9.81 ≈ 1 080 m (0.58 nm)Rate of turn 102.9 / 1 080 = 0.0953 rad/s × 57.3 ≈ 5.5°/s (≈ rate 1.8)Time for 360° 360 / 5.46 ≈ 66 s Induced drag n² = 1.414² ×2 at the same IAS
Chapter 22 · Turning Flight and Load Factor
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put a whole turn together. A jet flies a level, balanced turn at two hundred knots true airspeed with forty-five degrees of bank, and its level-flight stalling speed is a hundred and ten knots. The load factor is one over cos forty-five, which is one point four one g. The stalling speed in the turn is a hundred and ten times the square root of one point four one four, which is about a hundred and thirty-one knots. For the radius, convert the speed: two hundred knots is about a hundred and three metres per second. Tan forty-five is one, so the radius is a hundred and three squared over nine point eight one, about one thousand and eighty metres. The rate of turn is the speed over the radius, nought point nought nine five radians per second, or about five and a half degrees per second, so a full circle takes about sixty-six seconds. And the induced drag doubles.
Summary
What to take into the exam Turning force Horizontal component of lift = centripetal force. Bank turns the aircraft; rudder balances.
Equations L cos φ = W; L sin φ = WV²/gr; tan φ = V²/gr .
Load factor n = 1/cos φ , bank only. 30° 1.15, 45° 1.41, 60° 2.0. Rises at an increasing rate.
Stall in a turn VS × √n : 70 kt → 99 kt at 60°.
Radius and rate r = V²/(g tan φ) ; ω = V/r. Double V: r ×4, rate ÷2.
Rate 1 3°/s; tan φ = ωV/g; ≈ TAS/10 + 7. More speed needs more bank.
Limits Stall, strength (2.5 g ≈ 66°) and thrust. Minimum radius at VA .
Balance Step on the ball. Slip: ball inside. Skid: ball outside (too little bank).
Chapter 22 · Turning Flight and Load Factor
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
To finish, the key points. An aircraft turns because the horizontal component of its lift provides the centripetal force; the bank turns it and the rudder keeps it balanced. In a level turn, L cos phi equals W, L sin phi equals W V squared over g r, and dividing gives tan phi equals V squared over g r. The load factor is one over cos phi and depends only on bank: one point one five at thirty, one point four one at forty-five, two at sixty. The stall speed rises with the square root of n. The radius is V squared over g tan phi, so doubling the speed gives four times the radius and half the rate. A rate one turn is three degrees per second, needing about a tenth of the TAS plus seven degrees of bank. The minimum radius comes at V A. And step on the ball: in a skid it moves outside, in a slip inside.