Principles of Flight · Chapter 28
Windshear What windshear is, why the microburst is so dangerous, how shear changes airspeed and flight path on take-off and approach, the cockpit indications, the recovery technique, visual clues and reporting.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the chapter on windshear. A windshear is a sudden change in the wind over a short distance, and close to the ground it can push even a large, powerful jet off its flight path faster than its engines can respond. The most violent example is the microburst under a thunderstorm. In this lesson you will see how a change in wind becomes a change in airspeed, why some shears help you and others are deadly, what you see on your instruments, how to recover on take-off and on the approach, and above all how to recognise and avoid windshear in the first place.
Roadmap
Windshear: understand it, recognise it, avoid it The first and most vital defence against windshear is avoidance . Everything else in this lesson helps you recognise it early and survive an encounter you could not avoid.
1 · What it is Definition, causes, and the microburst: size, strength and life.
2 · What it does Microbursts on take-off and approach; energy gain and energy loss.
3 · What you see Cockpit indications for each type of shear, and why groundspeed matters.
4 · Recovery Maximum power, about 15° pitch, stick shaker as the limit.
5 · Clues and reports Visual warning signs and how to report windshear to ATC.
6 · The drill Recognise, recognise, avoid, prepare, recover.
Chapter 28 · Windshear
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Windshear has destroyed aircraft flown by experienced crews in modern, powerful aeroplanes, so this lesson matters. The first and most vital defence is avoidance, and everything else we cover helps you recognise windshear early and survive an encounter that you could not avoid. We work in six parts. First, what windshear is and where it comes from, and the most dangerous form of it, the microburst. Second, what a microburst does to an aircraft on take-off and on the approach, and the idea of energy gain and energy loss. Third, what you see on your instruments for each kind of shear. Fourth, the recovery technique. Fifth, the visual clues and how to report windshear. And finally the simple drill: recognise, recognise, avoid, prepare, recover.
Part 1 · Definition
What windshear is Windshear : a sudden, drastic change in wind speed and/or direction over a short distance It can occur at any altitude , in the vertical and/or horizontal plane It can bring sudden updraughts , downdraughts or extreme horizontal wind components Result: sudden loss of lift , violent changes in vertical speed or altitude Abrupt displacement from the flight path needing large control inputs Most dangerous close to the ground , on take-off and approach Change with height height shear layer speed and direction change Change with distance shear line headwind tailwind aircraft flies this way over a short distance
Chapter 28 · Windshear
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Windshear is a sudden, drastic change in wind speed, direction, or both, over a short distance. It can happen at any altitude, and the change can be with height, as in the left panel, or along the flight path, as on the right. It can hit an aircraft with a sudden updraught or downdraught, or with an extreme change in the horizontal wind. The effect is a sudden loss of lift, or violent changes in vertical speed and altitude, which knock the aircraft off its flight path and need large, quick control inputs to counter. At cruising altitude there is usually height to spare. Close to the ground, on take-off and approach, there is not, and that is where windshear kills. An encounter may cause nothing worse than alarm, it may damage the landing gear, or it may end in total catastrophe.
Part 1 · Causes
Where windshear comes from The most powerful windshear comes from thunderstorms , but it is not only a thunderstorm problem.
Thunderstorms Cumulonimbus downdraughts, gust fronts and above all microbursts : the strongest and most dangerous windshear.
Fronts The passage of a front , especially a fast cold front, brings a sharp wind change across the frontal zone.
Low-level inversion A marked temperature inversion near the surface can separate calm air below from strong wind above.
Chapter 28 · Windshear
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Where does windshear come from? By far the most powerful examples are associated with thunderstorms, that is, cumulonimbus clouds. Their downdraughts, the gust fronts that spread from them, and above all microbursts, produce the strongest and most dangerous shear an aircraft can meet. But windshear is not only a thunderstorm problem. The passage of a front, especially a fast-moving cold front, brings a sharp change of wind across the frontal zone, which you may fly through on the approach. And a marked low-level temperature inversion, for example on a clear night, can leave calm air near the ground under a strong wind just above it, so the wind changes rapidly as you descend through the inversion. The meteorology of these features belongs to the Meteorology course; here we concentrate on what they do to the aircraft.
Part 1 · The microburst
The microburst: a small, intense downdraught < 1 mile outflow about 4 km (2½ nm) across 1 000–3 000 ft downdraught: up to 6 000 ft/min headwind for an aircraft flying left to right tailwind Microburst Core < 1 mile Down 6 000 fpm Outflow 45 kt Shear 90 kt Worst < 1 000 ft Life ≤ 15 min Figures are typical maxima. Close to the ground, within about 1 000 ft, it is dangerous to every aircraft, however large.
Chapter 28 · Windshear
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
A microburst is a small-scale, intense downdraught that, on reaching the surface, spreads outward in all directions. The descending column is typically less than one mile across, and it comes down from the cloud base to about one to three thousand feet above the ground. Downdraughts can reach six thousand feet per minute. Near the ground the column turns into a horizontal outflow about four kilometres across, with winds of up to forty-five knots within a few hundred feet of the surface. An aircraft flying through it first meets a forty-five knot headwind and then a forty-five knot tailwind, a total shear of ninety knots. The red path shows a take-off flown at constant attitude and power: the first headwind helps, followed by the downdraught, then the tailwind, and the path ends in impact with the ground. These are maximum values, but they show how even large and powerful aircraft can be overwhelmed.
Part 1 · Lifetime
How long a microburst lasts A microburst intensifies for about 5 minutes after it first strikes the ground The maximum winds last about 2 to 4 minutes An individual microburst seldom lasts longer than 15 minutes to dissipation Microbursts in a line can keep activity going for about an hour Once one starts, more in the same area are not uncommon: expect them So a short delay is often the safest answer 0 5 10 15 20 Minutes after striking the ground Wind strength peak 2–4 min intensifies ≈ 5 min gone within ≈ 15 min In a line of microbursts activity can last about an hour. Once one starts, expect others nearby.
Chapter 28 · Windshear
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
A microburst is short-lived, which is good news for the pilot who can wait. After it first strikes the ground it intensifies for about five minutes. The strongest winds then last about two to four minutes, and an individual microburst seldom lasts more than fifteen minutes from the time it hits the ground until it dissipates. Two warnings, though. Microbursts sometimes form in a line, and then activity may go on for as long as an hour. And once microburst activity starts, more microbursts in the same general area are not unusual and should be expected, so one that has passed does not mean the area is clear. In practice this lifetime means that a short delay on the ground, or a short hold in the air away from the storm, is very often the safest decision you can make.
Part 2 · Take-off
Taking off into a microburst Cumulonimbus downdraught up to 6 000 ft/min outflow outflow 1 more headwind 2 downdraught 3 tailwind 4 headwind (kt) tailwind vertical wind (dashed, ft/min ÷ 100) +45 −45 distance through the microburst (about 1 nm between the wind peaks; the core is less than 1 mile across) · heights exaggerated Path computed at constant pitch and power: each knot of headwind gained or lost is worth about 13 ft of height (V·ΔV ÷ g), and the downdraught carries the aircraft down with it.
Chapter 28 · Windshear
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow a take-off into a microburst. The path in red is computed for an aircraft that keeps a constant pitch attitude and power, so you can see what the air alone does. At point one the aircraft meets the outflow as an increasing headwind. Its airspeed rises without any change of pitch or power, so performance improves and it climbs steeply. That improvement is a trap. At point two the headwind dies away and the strong downdraught begins, so performance decreases. At point three the wind has sheared to a tailwind, still inside the downdraught, and performance keeps falling. The most severe downdraught is met between points two and three, and the result can be an uncontrollable descent and impact with the ground at point four. Look at the strip below: the headwind swings from plus forty-five to minus forty-five knots in about two nautical miles.
Part 2 · Approach
Flying an approach through a microburst Cumulonimbus downdraught up to 6 000 ft/min outflow outflow glide slope 1 balloons above 2 downdraught: sinks headwind (kt) tailwind vertical wind (dashed, ft/min ÷ 100) +45 −45 distance through the microburst (about 1 nm between the wind peaks; the core is less than 1 mile across) · heights exaggerated Flown without correction, the aircraft first goes high, then sinks through the glide slope and strikes the ground well short of the runway.
Chapter 28 · Windshear
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the same microburst on the approach. The green dashed line is the three degree glide slope, and the red path is computed again for constant attitude and power. As the aircraft enters the outflow, the headwind increases, the airspeed rises and the aircraft balloons above the glide slope. A pilot who reacts only to that will reduce power and lower the nose, exactly the wrong preparation for what follows. Next comes the downdraught, which pushes the aircraft down, and then the tailwind, which takes away airspeed. The aircraft sinks through the glide slope and, in this computed case, strikes the ground well short of the runway. The rising airspeed and the balloon at the start, with a thunderstorm nearby, are your warning. That is the moment to abandon the approach and go around, while you still have the extra energy the headwind has given you.
Part 2 · Two reference frames
Why a wind change is an airspeed change An aircraft has two references: the air mass (IAS) and the ground (groundspeed) Crossing a shear line, inertia keeps the groundspeed at first So the wind change appears immediately as an IAS change Headwind 10 → 60 kt at groundspeed 130: IAS 140 → 190 kt Wind is energy: when it shears, the aircraft gains or loses energy Later the aircraft settles to its trimmed IAS and a new groundspeed Before the shear groundspeed 130 +10 IAS 140 kt Just after: headwind 60 kt groundspeed 130 wind 60 IAS 190 kt inertia holds the groundspeed at first IAS ≈ groundspeed + headwind component a sudden wind change appears at once as an airspeed change
Chapter 28 · Windshear
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
To understand windshear you must keep two reference points in mind: the air mass, which gives you your indicated airspeed, and the ground, which gives you your groundspeed. In steady wind, airspeed is roughly groundspeed plus the headwind component. When the aircraft crosses a shear line, the airspeed changes suddenly, but the aircraft is heavy and its inertia keeps it moving at its original groundspeed for a while. So the whole wind change shows up at once as a change of indicated airspeed. In the example, the aircraft is at one hundred and thirty knots groundspeed in a ten knot headwind, so its airspeed is one hundred and forty. The headwind jumps to sixty knots, the groundspeed is still one hundred and thirty, and the airspeed leaps to one hundred and ninety knots. Wind is a form of energy: when it shears, the aircraft gains or loses that energy.
Part 2 · Performance-increasing shear
Energy gain: more headwind, or less tailwind A rapid increase in headwind or loss of tailwind is an energy gain Also: tailwind to calm, calm to headwind; an updraught also helps IAS rises , the nose pitches up , the aircraft balloons above the pathExample: IAS 140 → 190 kt ; 700 ft/min down → 200 ft/min up It temporarily improves performance Near a thunderstorm it is the forerunner of a microburst : be ready Energy gain rapid increase in headwind glide slope shear line headwind 10 → 60 kt IAS 140 kt Groundspeed 130 kt Vertical 700 ft/min ↓ IAS 190 kt Groundspeed 130 kt Vertical 200 ft/min ↑
Chapter 28 · Windshear
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
A rapid increase in headwind, or a sudden loss of tailwind, is an energy gain. So is a shear from tailwind to calm, or from calm to headwind, and an updraught helps in the same way. Here is the example. On the approach the aircraft has a ten knot headwind, an airspeed of one hundred and forty knots, a groundspeed of one hundred and thirty, and a descent of seven hundred feet per minute. It crosses a shear line into a sixty knot headwind. The groundspeed is still one hundred and thirty, so the airspeed rises to one hundred and ninety knots. Lift rises with it, the nose pitches up and the aircraft balloons, climbing at two hundred feet per minute above the glide slope. Performance temporarily improves. But near a thunderstorm this is exactly how a microburst begins, so treat the gain as a warning, and as a bonus to use, not a problem to fix.
Part 2 · Performance-decreasing shear
Energy loss: less headwind, more tailwind, or a downdraught Loss of headwind headwind 10 kt → tailwind 20 kt glide slope shear line wind change 30 kt IAS 140 kt Groundspeed 130 kt Vertical 700 ft/min ↓ IAS 110 kt Groundspeed 130 kt Vertical 1 000 ft/min ↓ Downdraught air descending through the approach path glide slope shear line downdraught IAS 140 kt Groundspeed 130 kt Vertical 700 ft/min ↓ IAS 110 kt Groundspeed 130 kt Vertical 1 500 ft/min ↓ A sudden drop of headwind , an increase in tailwind and a downdraught are all energy losses: the main danger at low altitude.
Chapter 28 · Windshear
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The dangerous kind of shear is the energy loss. Both panels start from the same approach: one hundred and forty knots airspeed, one hundred and thirty groundspeed, seven hundred feet per minute down. On the left, the ten knot headwind shears to a twenty knot tailwind, a change of thirty knots. Groundspeed stays at one hundred and thirty, so the airspeed falls at once to one hundred and ten knots. Lift falls, the nose drops, and the descent increases to about one thousand feet per minute, taking the aircraft below the glide slope. On the right, the aircraft flies into a downdraught. The air it is flying in is itself moving down, so the descent rate rises to about fifteen hundred feet per minute, and the airspeed falls to one hundred and ten. Sudden loss of headwind, increase of tailwind, and downdraughts are the main danger at low altitude, because there is so little height to recover.
Part 2 · Vertical shear
Downdraughts and updraughts change the angle of attack A downdraught moves the relative airflow so it comes from above : the angle of attack falls Lift falls at once and the sink rate rises , even before the airspeed changes An updraught does the opposite: α and lift rise, the aircraft balloons Example: 1 500 ft/min (25 ft/s) at 140 kt TAS: Δα ≈ 6° The aircraft is also carried down with the descending air mass Holding a high pitch restores the angle of attack: up to the stick shaker TAS (relative airflow) downdraught new relative airflow −Δα lift falls Downdraught: α falls → lift falls → sink rate rises Updraught: α rises → lift rises → aircraft balloons A 1 500 ft/min downdraught at 140 kt TAS: Δα = arctan(25 ÷ 236) ≈ 6° that is most of the approach angle of attack
Chapter 28 · Windshear
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Vertical shear works through the angle of attack. In a downdraught, the air the wing is flying through is moving down. Add that downward motion to the aircraft true airspeed, and the relative airflow now comes from slightly above, so the angle of attack falls. Lift falls immediately, before the airspeed has had time to change, and the aircraft starts to sink. At the same time the whole aircraft is being carried down with the descending air. The numbers are large: a downdraught of fifteen hundred feet per minute, which is twenty-five feet per second, at one hundred and forty knots true reduces the angle of attack by about six degrees, which is most of the angle you fly the approach at. An updraught does the opposite and makes the aircraft balloon. This is why the recovery uses a high pitch attitude: it restores the angle of attack, up to the stick shaker.
Part 3 · What you see on the approach
Indications and actions for horizontal shear Guidance for a shear met during a stabilised approach. Never start an approach into known windshear.
Headwind → calm or tailwind Tailwind → calm or headwind Indicated airspeed Decreases Increases Pitch attitude Decreases Increases Aircraft Tends to sink Balloons Groundspeed Increases Decreases Power Increase Decrease Fly Up to the glide slope Down to the glide slope Then be prepared to Reduce power; increase rate of descent (faster groundspeed) Increase power; decrease rate of descent (slower groundspeed)
Chapter 28 · Windshear
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table is the pilot's guide to horizontal shear on a stabilised approach. In the middle column the wind shears from a headwind to calm or to a tailwind. The airspeed decreases, the pitch attitude decreases as the aircraft tries to regain speed, the aircraft tends to sink, and the groundspeed increases. So you increase power and fly back up to the glide slope. Then comes the subtle part. Once you are re-established, the higher groundspeed needs a higher rate of descent to stay on the slope, so be ready to reduce power again. In the right column the wind shears from a tailwind to calm or a headwind, and everything reverses: airspeed and pitch increase, the aircraft balloons, groundspeed falls. Reduce power and fly down to the glide slope, then be ready to add power for the lower rate of descent. And never start an approach into known windshear.
Part 3 · Why groundspeed matters
Rate of descent follows groundspeed The glide slope is fixed to the ground , so the descent rate needed depends on groundspeed On a 3° slope: ROD ≈ groundspeed × 5.3 ft/min 130 kt → 690 ft/min ; 160 kt → 850 ft/min ; 110 kt → 580 ft/min Shear to tailwind : more groundspeed, so more ROD and less power once re-established Shear to headwind : less groundspeed, so less ROD and more power Compare power and ROD with the normal values: a big difference means shear 400 600 800 1000 80 100 120 140 160 180 Groundspeed (knots) Rate of descent (ft/min) 110 kt → 580 ft/min 30 kt headwind 130 kt → 690 ft/min reference 160 kt → 850 ft/min 20 kt tailwind ROD ≈ groundspeed × 5.3 on a 3° glide slope (rule of thumb: groundspeed × 5, or × 10 ÷ 2)
Chapter 28 · Windshear
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does the last row of that table say you need a different rate of descent after the shear? Because the glide slope is fixed to the ground, not to the air. The rate of descent needed to follow a three degree slope depends on your groundspeed: it is about five point three feet per minute for every knot. At one hundred and thirty knots groundspeed that is about six hundred and ninety feet per minute, which matches the seven hundred in our examples. If a tailwind of twenty knots pushes the groundspeed up to one hundred and sixty, you need about eight hundred and fifty feet per minute, so less power once you are back on the slope. With a thirty knot headwind and a groundspeed of one hundred and ten, you need only about five hundred and eighty, so more power. This is also a detection tool: if the power or descent rate needed is far from normal, suspect windshear.
Part 4 · Recovery
The "typical" microburst recovery Cumulonimbus downdraught up to 6 000 ft/min outflow outflow glide slope 1 go-around: max power, 15° pitch 2 hold attitude, accept low IAS 3 most critical: stick shaker if needed headwind (kt) tailwind vertical wind (dashed, ft/min ÷ 100) +45 −45 distance through the microburst (about 1 nm between the wind peaks; the core is less than 1 mile across) · heights exaggerated Headwind, then downdraught, then tailwind: the sequence on the approach or after take-off. Assume the worst from the first sign.
Chapter 28 · Windshear
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the typical recovery when a microburst is met on the approach. Expect the sequence: increasing headwind, then downdraught, then increasing tailwind. With a thunderstorm about, the rising airspeed from the headwind is the forerunner of the burst. Abandon any hope of a stabilised approach, and see the extra airspeed and the balloon as a bonus to capitalise on. Without hesitation set go-around power, be ready to use maximum, and select a missed approach pitch of about fifteen degrees, holding it against turbulence. Next the downdraught strikes. Airspeed falls and the aircraft may descend despite the power and pitch. Keep the attitude; relax it only if the stick shaker triggers. The point where the downdraught turns into tailwind may be the most critical. If ground contact still threatens, raise the nose further, to the stick shaker, and hold just below it until you escape the burst.
Part 4 · The vital actions
Power, pitch, and the stick shaker Use the maximum power available as soon as possible Adopt a pitch of about 15° and hold it : do not chase airspeed Be guided by the stick shaker : ease back pressure to hold a slightly lower attitude If terrain still threatens: raise the nose to the stick shaker and hold just below it Ignore noise abatement ; do not change configurationLowering the nose to regain speed trades away the height you cannot spare horizon max thrust ≈ 15° 1 Maximum available power, at once 2 Pitch about 15°, hold it; do not chase airspeed 3 Stick shaker: ease back pressure, hold a slightly lower attitude 4 No configuration changes; ignore noise abatement
Chapter 28 · Windshear
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Whether it happens on the approach or after take-off, the vital actions are the same. First, use the maximum power available, as soon as possible; engine limits matter less than the ground. Second, adopt a pitch attitude of about fifteen degrees and hold it. Do not chase the airspeed. Lowering the nose to get the speed back trades away height, and height is exactly what you cannot spare. Third, let the stick shaker be your guide: if it triggers, ease the back pressure just enough to hold a slightly lower attitude. If you are still sinking towards the ground or an obstacle, raise the nose further, deliberately, to the stick shaker, and hold the attitude just below it. Ignore noise abatement procedures, and do not change the configuration while you are in the shear. Your aircraft's own procedure, if it has one, takes priority.
Part 4 · On the ground
When windshear is possible at take-off Best: delay the take-off until the storm has passed Use the longest runway , or one pointing away from the threat Consider rotating at a slightly higher speed , within tyre and handling limits Use maximum take-off power , not reduced thrust After rotation the high power and pitch are already a good recovery configuration, but you are very low Hold the high pitch, use any extra power, ignore noise abatement ; stick shaker is the limit RWY 09 RWY 18 (longer) CB with microburst depart away from the storm If windshear is possible but not certain:
Chapter 28 · Windshear
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
What if windshear is possible but not certain when you are about to take off? The best answer is to wait: a microburst rarely lasts more than fifteen minutes. If you do go, use a longer runway, or one that points away from the area of threat, like runway one eight in the picture rather than runway zero nine, which heads straight for the storm. It may also be wise to rotate at a slightly higher speed, provided that does not overstress the tyres or cause handling problems, because the extra speed is extra energy. After rotation, the high power and high pitch already put the aircraft in a good configuration should a microburst be met. But you are very low, there is little margin and the ride may be rough. If there is any more power available, use it without hesitation, ignore noise abatement, and keep the high pitch, easing back pressure only when the stick shaker warns you.
Part 4 · On the approach
Any doubt: full power and go around Monitor the power and vertical speed needed to hold the glide slope Shear makes it hard to stay on the slope with normal power and descent rate If in any doubt you can land without abnormal manoeuvres: full power and go around You cannot tell how severe it will be: assume the worst case Example: IAS −30 kt , descent 750 → 2 000 ft/min : go around, then report Never start an approach into known windshear; carry a speed margin if loss is suspected Thrust held for target IAS, on the glide slope: expected observed IAS target −30 kt Rate of descent 750 ft/min 2 000 ft/min Glide slope on going low Power needed normal abnormal FULL POWER · GO AROUND then report the windshear to ATC do not wait to see if it improves
Chapter 28 · Windshear
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the approach, watch the power and the vertical speed you need to hold the glide slope. In windshear it becomes hard to stay on the slope with normal power and normal descent rates. If there is ever any doubt that you can re-establish a reasonable rate of descent and land without abnormal manoeuvres, apply full power and go around. Windshear varies enormously, and in the first seconds of an encounter you cannot tell how severe it will become, so assume the worst case and act on it. Here is the classic exam case. Thrust is being managed for the target airspeed on the glide slope, and suddenly you see a thirty knot loss of airspeed while the descent rate rises from seven hundred and fifty to two thousand feet per minute. Do not try to fix it and continue. Apply full power, go around, and report the windshear to air traffic control as soon as practicable.
Part 5 · Visual clues
Think windshear: the signs outside A visible thunderstorm is the trigger to think windshear . Then look for the tell-tale signs; any of them means the danger is close, if not imminent.
Divergent wind Windsocks or smoke pointing in different directions.
Rain shafts and virga Strong shafts of rain or hail; virga , rain evaporating in dry air below a CB.
Beaten vegetation Grass, crops or trees beaten down or lashed in a spreading pattern.
Rising dust Dust or sand raised from the ground, often in a ring.
Chapter 28 · Windshear
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
You can see a thunderstorm, and seeing one should be the mental trigger to think windshear. Once you are alerted, look for the tell-tale signs. Windsocks or smoke pointing in different directions show divergent wind, the outflow of a burst. Strong shafts of rain or hail falling from the cloud, or virga, which is precipitation falling from the base of a cumulonimbus and evaporating in the dry air below it, show where the downdraught is; evaporation cools the air and can drive a strong one. Grass, crops or trees being beaten down or lashed in a spreading pattern show the outflow on the ground. And dust or sand rising from the surface, often in a ring, marks the outflow too. If you see any of these, windshear danger is very close, if not imminent. A few seconds of warning can make all the difference, if you heed it and use those seconds well.
Part 5 · Reporting
Report it: the next crew needs to know Report any windshear on approach or departure promptly to the controller Advance warning helps other pilots avoid or cope with it Recommended: state the loss or gain of airspeed and the altitudes where it was met If you cannot give figures, report the effect on your aircraft Example: "loss of 20 knots between 600 and 400 feet " Report after the go-around is under control: aviate first Pilot Windshear on final runway two seven: loss of 20 knots between 600 and 400 feet. ATC Next aircraft: windshear reported on final, loss of 20 knots, 600 to 400 feet. If you cannot give figures Report the effect: "severe sink on short final, needed full power"
Chapter 28 · Windshear
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
If you meet windshear on an approach or a departure, report it promptly to the controller. Your warning can help the pilots behind you either avoid it or be ready for it. The recommended way is to state the loss or gain of airspeed and the altitudes at which it happened, for example: windshear on final runway two seven, loss of twenty knots between six hundred and four hundred feet. That tells the next crew both the size of the shear and where to expect it. If you cannot put figures on it, report it in terms of its effect on your aircraft, for example severe sink on short final needing full power. Of course, aviate first: fly the recovery or the go-around, and make the report once the aircraft is under control.
Part 6 · The drill
Recognise, avoid, prepare, recover Most pilots meet windshear only as a firm landing or a swing they put down to "gusts". A few find it stretches them to the limit. Do not put your skills to the test.
Recognise that windshear is a hazard to all sizes and types of aircraft.
Recognise the signs that may show it is present: storms, clues, reports, instruments.
Avoid windshear by delaying departure, or diverting if airborne.
Prepare for an inadvertent encounter with a speed margin if energy-loss shear is suspected.
Recover know the technique for your aircraft and use it without hesitation .
Decide early An approach destabilised by shear calls for a missed approach : the sooner, the safer.
Chapter 28 · Windshear
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Most pilots will meet windshear in some form. For most it is nothing more than a very firm landing, or a swing on take-off or landing that needs a moment of full rudder, and they put it down to gusts. A few meet the real thing, which stretches their skills to the limit, and a very small number find their skills are not enough. There is no sure way of knowing the severity in advance, so do not put your skills to the test. Remember the drill. Recognise that windshear is a hazard to every aircraft. Recognise the signs that it may be present. Avoid it by delaying or diverting. Prepare for an inadvertent encounter by carrying a speed margin when energy-loss shear is suspected. And recover using your aircraft's technique without hesitation. An approach destabilised by shear calls for a missed approach, and the sooner you decide, the safer you are.
Summary
What to take into the exam Definition Sudden drastic change of wind speed and/or direction over a short distance, any altitude, vertical or horizontal.
Microburst < 1 mile core; down to 1 000–3 000 ft; 6 000 ft/min; 45 kt outflow = 90 kt shear; outflow ≈ 4 km.
Lifetime Builds ~5 min, peak 2–4 min, seldom > 15 min; lines up to 1 hour; expect more than one.
Sequence Headwind, then downdraught, then tailwind: on the approach and after take-off.
Energy gain More headwind, less tailwind (tailwind → calm, calm → headwind): IAS, pitch up, balloon.
Energy loss Less headwind, more tailwind, downdraught: IAS, pitch down, sink. The low-level danger.
Recovery Max power at once; ~15° pitch and hold; don't chase IAS; stick shaker is the limit; no noise abatement.
Clues and reports Divergent socks, rain shafts, virga, beaten crops, dust. Report IAS change and altitudes.
Chapter 28 · Windshear
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up windshear. It is a sudden, drastic change in wind speed or direction over a short distance, at any altitude. The microburst is its most dangerous form: a core less than a mile wide, down to one to three thousand feet, downdraughts up to six thousand feet per minute, and forty-five knot outflows giving a ninety knot shear. It builds for about five minutes, peaks for two to four, and rarely lasts more than fifteen. Expect headwind, then downdraught, then tailwind, both on approach and after take-off. More headwind or less tailwind is an energy gain: airspeed and pitch up, and a balloon. Less headwind, more tailwind or a downdraught is an energy loss: airspeed down and sink. To recover, use maximum power at once, hold about fifteen degrees of pitch, do not chase airspeed, and use the stick shaker as the limit. Watch for the visual clues, and report the airspeed change and the altitudes.