Principles of Flight · Chapter 6
The Three-Dimensional Wing Real wings have tips: spanwise flow, tip vortices, induced downwash and induced drag, wake turbulence, and what happens close to the ground.
viewed from behind
left tip clockwise · right tip anticlockwise · downwash between
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
So far we have studied a single slice of wing, as if the wing went on for ever. Real wings end, and at each tip the high pressure underneath leaks round to the low pressure on top. That one fact creates tip vortices, induced downwash and induced drag, shapes the lift along the span, leaves dangerous wake turbulence behind every aeroplane, and changes how the aircraft behaves in the last few metres before touchdown. This lesson follows the air round the wingtip and out the other side.
Lesson map
From a slice of wing to a whole wing 1 · The wing Span, chord, area, aspect ratio, taper, sweep and MAC; common planforms.
2 · Vortices Spanwise flow, tip vortices, induced downwash, induced drag, aspect ratio and lift distribution.
3 · The wake Wake turbulence: when it starts, how strong, where it goes, and how to avoid it.
4 · The ground Ground effect on lift and drag, the tailplane and pitch, entering and leaving it.
Chapter 6 · The Three-Dimensional Wing
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
In this lesson we put the section back into a real wing. Part one gives us the vocabulary for a whole wing: span, chord, area, aspect ratio, taper, sweep and the mean aerodynamic chord. Part two is the heart of it: at the tips, high pressure from underneath leaks round to the top, setting up spanwise flow and tip vortices. Those vortices create induced downwash, which reduces the effective angle of attack and produces induced drag, and we will see how aspect ratio and planform change all of that. Part three follows the vortices behind the aircraft as wake turbulence, a real hazard to anyone following. And part four looks at what happens in the last few metres above the runway, where the ground interferes with the vortices and the aircraft behaves differently in lift, drag and pitch.
Part 1 · The wing
Why real airflow is three-dimensional Even tiny pressure differences make air flow towards lower pressure Higher pressure under the wing, lower above: air spills round the tips On top the flow drifts inboard ; underneath it drifts outboard Where they meet, at the trailing edge and tips, the flow rolls up into vortices Effects: lower effective α, more drag , changed stall, control and stability
Upper surface (lower pressure)
flow drifts inboard, towards the root
Lower surface (higher pressure)
flow drifts outboard, towards the tips
Top views, flight direction up. Purple: air spilling round the tips
Chapter 6 · The Three-Dimensional Wing
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Up to now we imagined a wing with no ends. A real wing has tips, and that changes everything. Air always moves towards lower pressure, even when the pressure difference is tiny. Under the wing the pressure is higher, and above it is lower, so at the tips the air spills round from bottom to top. The effect spreads across the whole span. On the upper surface the flow drifts inboard, towards the root, while on the lower surface it drifts outboard, towards the tip. Where the two meet, at the trailing edge and especially at the tips, they roll up into vortices. This three-dimensional flow lowers the effective angle of attack, increases drag, alters how the wing stalls, and can influence control and stability. From now on we think about the whole wing, not just one section.
Part 1 · The wing
Wing terminology
sweep of the 25% chord line, 23°
MAC
C R root chord
C T tip chord
span b (tip to tip)
S = b × c̄
AR = b ÷ c̄ = b² ÷ S
taper = C T ÷ C R = 0.4
MAC: chord through the
centre of the plan area
Span b : tip to tip. Average chord c̄ = S ÷ b. Aspect ratio = b ÷ c̄ = b² ÷ S. Taper ratio = C T ÷ C R. Sweep : usually of the 25% chord line.
Chapter 6 · The Three-Dimensional Wing
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the language for a whole wing. Wing area, S, is the plan area, including the part covered by the fuselage and nacelles, because the pressure carries over onto them. The span, b, is measured from tip to tip. The average chord is the geometric average, so span times average chord gives the area. Aspect ratio is span divided by average chord; when the chord varies and is hard to average, use span squared divided by area, which comes to the same thing. The root chord is the chord at the centreline, the tip chord is at the tip, and taper ratio is tip chord divided by root chord. Sweep is usually measured on the line joining the quarter-chord points. Finally, the mean aerodynamic chord is the chord through the centre of the plan area; a rectangular wing of that chord would have similar pitching moments, which makes it the reference for balance and stability.
Part 1 · The wing
Worked example: aspect ratio and area AR = b ÷ c̄ , or b² ÷ S if the chord variesA: 51 m × 4 m → S = 204 m² , AR = 12.75 B: 48 m × 3.5 m → S = 168 m² , AR = 13.7 B has the higher AR but the smaller area AR sets aerodynamic behaviour and structural weight: sailplane ~35, transport ~12, fighter ~3
Aircraft A: span 51 m, average chord 4 m
S = 51 × 4 = 204 m² AR = 51 ÷ 4 = 12.75
Aircraft B: span 48 m, average chord 3.5 m
S = 48 × 3.5 = 168 m² AR = 48 ÷ 3.5 = 13.71
Typical aspect ratios
Sailplane
35
Jet transport
12
Jet fighter
3
Chapter 6 · The Three-Dimensional Wing
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us practise with two aircraft, a classic exam question. Aircraft A has a span of fifty-one metres and an average chord of four metres. Its area is fifty-one times four, two hundred and four square metres, and its aspect ratio is fifty-one divided by four, twelve point seven five. Aircraft B has a span of forty-eight metres and an average chord of three and a half metres. Its area is one hundred and sixty-eight square metres, and its aspect ratio is forty-eight divided by three point five, about thirteen point seven. So B has the higher aspect ratio but the smaller wing area; the longer span does not automatically mean the higher aspect ratio. The aspect ratio has a strong influence on aerodynamic characteristics and on structural weight. Typical values run from about thirty-five on a high-performance sailplane, through about twelve on a modern jet transport, down to about three on a jet fighter.
Part 1 · The wing
Planforms and taper
Rectangular
taper 1.0
Tapered
taper 0.4
Elliptical
curved
Swept
25–35°
Delta
taper 0
Taper ratio Rectangular wing: 1.0 . Pointed delta: 0 . Taper affects the lift distribution and the structural weight.
Sweep Measured on the 25% chord line. Sweep changes compressibility effects, maximum lift and stall behaviour.
Ellipse An elliptical wing gives an elliptical lift distribution : uniform downwash and the least induced drag for its span.
Chapter 6 · The Three-Dimensional Wing
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Wings come in a handful of planform families. A rectangular wing has a constant chord, so its taper ratio is one. A tapered wing narrows towards the tip, say to a taper ratio of point four. An elliptical wing has a curved outline, famous on some classic fighters, and as we will see it gives the most even downwash. A swept wing has its quarter-chord line angled back, typically twenty-five to thirty-five degrees on a jet transport. And a pointed delta has no tip chord at all, so its taper ratio is zero. Taper ratio matters because it changes how the lift is spread along the span and how heavy the structure must be. Sweep changes the compressibility behaviour at high Mach numbers, the maximum lift and the stalling characteristics. We will come back to sweep in the high-speed lessons.
Part 2 · Vortices
Wingtip vortices: which way they turn
left tip: clockwise
right tip: anticlockwise
downwash behind the wing
Viewed from behind
under the wing: outward · round the tip: upward · on top: inward
Seen from behind : the left tip vortex turns clockwise and the right one anticlockwise . Air goes outward under the wing, up round the tip and inward on top.
Chapter 6 · The Three-Dimensional Wing
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Follow the air round a wingtip. By convention we look at the aircraft from behind. Under the right wing the air flows outward, towards the tip; it rises round the tip and flows inward over the top. That circulation, seen from behind, is anticlockwise at the right wingtip. The left wing is the mirror image, so its vortex turns clockwise. Between the two vortices, behind the wing, the air is moving downward; that is the downwash. So the exam phrase is: outward, upward and around the wingtip. In the live picture, the camera is behind and slightly to one side of the wing, and you can see the two spirals streaming back from the tips with the correct rotation. Trailing vortices are not confined to the tips; vorticity is shed all along the trailing edge, but it quickly rolls up into these two concentrated vortices.
Part 2 · Vortices
What makes vortices stronger The spanwise flow is set by the pressure difference, so by the lift At low IAS and high α the chordwise flow is slower The same spanwise push then turns the flow more So vortices are stronger at high α, low IAS Stronger vortices: more downwash, more induced drag
High IAS, low α
chordwise
spanwise
flow turned 17° inboard
Low IAS, high α
chordwise
spanwise
flow turned 32° inboard
Same lift, same spanwise push; less chordwise speed
→ bigger spanwise deflection → stronger vortices
Top view of upper-surface flow (not to scale)
Chapter 6 · The Three-Dimensional Wing
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why are vortices stronger when the aircraft is slow? Think of the flow over the upper surface as two components added together: a chordwise component, flowing back over the wing at roughly the airspeed, and a spanwise component, driven inboard by the pressure difference. In level flight the lift equals the weight whatever the speed, so the spanwise push is about the same. At high indicated airspeed and low angle of attack the chordwise flow is fast, so the spanwise component only turns it a little. At low indicated airspeed and high angle of attack the chordwise flow is slower, so the same spanwise component turns the flow much more. The resultant spanwise effect is greater and the vortices are stronger. That is the key rule: vortices are strongest at high angle of attack and low speed, and stronger vortices mean more downwash and more induced drag.
Part 2 · Vortices
Induced downwash lowers the effective angle of attack Trailing vortices induce vertical velocities ahead of, over and behind the wing Upwash ahead, downwash over and behind the wing Downwash at the wing reduces the effective angle of attack So the wing makes less lift than a 2D section at the same α It is lift production itself that reduces the lift
upwash ahead
downwash behind
downwash over the wing too:
effective angle of attack reduced
Vertical velocities are induced by the tip vortices;
stronger vortices, stronger up- and downwash
Chapter 6 · The Three-Dimensional Wing
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The trailing vortices do not just sit behind the aircraft; they change the flow around the wing itself. They induce vertical velocities in the air near the wing, ahead of it and behind it. Ahead of the wing there is upwash, and over and behind the wing there is downwash. The downwash at the wing tilts the airflow that the wing actually meets, so the effective angle of attack is less than the geometric angle between the chord and the relative airflow. The stronger the vortices, the bigger that reduction. Because of it, the whole wing produces less lift than the same section would in two-dimensional flow at the same angle of attack. There is a neat irony here: it is the production of lift itself, through the pressure difference that drives the vortices, that reduces the lift being produced.
Part 2 · Vortices
Induced drag: lift tilted backwards
relative airflow
effective airflow
chord line
α 12°
α e 7°
α i 5°
lift: 90° to the effective airflow,
tilted back by α i
induced drag D i = L × sin α i
More α is needed to get the
lost lift back: more drag
Angles exaggerated for clarity
Effective α = geometric α − induced α. Lift is perpendicular to the effective airflow , so it tilts back; its rearward component is induced drag .
Chapter 6 · The Three-Dimensional Wing
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is induced drag as a vector diagram, with the angles exaggerated so you can see them. The relative airflow arrives horizontally. The induced downwash bends the airflow the wing actually meets, the effective airflow, downward by a small angle called the induced angle of attack. The geometric angle of attack, here eight degrees, is measured from the relative airflow, but the effective angle of attack, measured from the effective airflow, is only five. Lift acts at right angles to the airflow the wing really meets, so it is tilted backward by the induced angle. Resolve it against the relative airflow: most of it acts upward, but a small part acts rearward, along the flight path. That rearward component is induced drag. To restore the lift lost to downwash the wing must fly at a higher angle of attack, which increases this drag further. The stronger the vortices, the greater the induced drag.
Part 2 · Vortices
Aspect ratio: why gliders have long thin wings The tips affect a region of roughly fixed size near each end of the wing On a high aspect ratio wing, a smaller share of the span is affected Less downwash for the same C L → less induced drag And a steeper lift curve : more C L per degree Low AR wings need a larger α for the same C L and make more induced drag
0°
4°
8°
12°
16°
20°
0.0
0.4
0.8
1.2
1.6
angle of attack (wing)
C L
2D section (AR ∞): 5.73 per rad
AR 12: 4.90 per rad
AR 6: 4.28 per rad
AR 3: 3.42 per rad
C D i = C L² ÷ (π × AR × e)
Lift-curve slopes computed with e = 0.9; linear part only
Chapter 6 · The Three-Dimensional Wing
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aspect ratio is the biggest single design factor in induced drag. Roughly speaking, the tip vortices disturb the flow over a region near each end of the wing. On a long, slender, high aspect ratio wing, that disturbed region is a small share of the total, so the average downwash for a given lift coefficient is small. On a short, stubby wing, much more of the span is affected. The result shows in two ways. First, induced drag: its coefficient is C L squared divided by pi times aspect ratio times an efficiency factor, so doubling the aspect ratio roughly halves the induced drag at the same C L. Second, the lift curve: a high aspect ratio wing has a steeper lift curve, closer to that of the two-dimensional section, while a low aspect ratio wing needs a larger angle of attack for the same lift. That is why sailplanes have long thin wings.
Part 2 · Vortices
Lift along the span The pressure difference leaks away at the tips, so lift falls to zero at each tip Elliptical distribution: uniform downwash, least induced drag Rectangular wing: highest local C L near the root , so the root stalls first Strong taper or sweep: local C L highest towards the tips Washout (twist, tip at lower incidence) unloads the tips
elliptical: least induced drag
rectangular wing
(Schrenk estimate)
tip
tip
root
Lift falls to zero at each tip, where the
pressure difference leaks away round the tip.
Washout (twist) unloads the tips;
strong taper or sweep loads them more.
Chapter 6 · The Three-Dimensional Wing
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the pressure difference leaks away round the tips, the lift per metre of span must fall to zero at each tip. How it varies in between depends on the planform and twist. The ideal is an elliptical distribution, which gives the same downwash all along the span and the least induced drag for a given span and lift; an elliptical planform produces it naturally. A rectangular wing has the highest local lift coefficient near the root, so at high angles of attack the root reaches the stall first, which is a gentle characteristic. Strong taper and sweep do the opposite, loading the outer wing, so the tips tend to stall first. Designers use washout, twisting the wing so the tip is at a lower incidence than the root, to unload the tips. We will return to stall patterns in the stall lesson.
Part 3 · The wake
Wake turbulence: when it starts and stops Trailing vortices extend a long way behind the aircraft; they cannot be seen Tangential speeds up to about 90 m/s (300 ft/s) just behind a large aircraft Generated from nosewheel lift-off to nosewheel touchdown , whenever lift is produced Every aircraft makes them, helicopters included ; heavy aircraft the worst Most dangerous near the ground: take-off, initial climb, final approach, landing
Take-off
nosewheel lifts: wake begins
Landing
nosewheel touches down: wake ends
Shaded: where wake vortices are being generated
Chapter 6 · The Three-Dimensional Wing
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Those trailing vortices do not vanish when the aircraft has passed. They extend a long way behind it, and they can be an extreme hazard to anyone who flies into them. Just behind a large aircraft the air in the vortex can be spinning at up to about ninety metres per second, around three hundred feet per second, and you cannot see it. Wake vortices are created whenever the wing is producing lift: from the moment the nosewheel lifts off on take-off until the nosewheel touches down on landing. Every aircraft produces them, helicopters included, but heavy aircraft produce the most severe. The greatest danger is near the ground, during take-off, initial climb, final approach and landing, where many aircraft congregate. An encounter can cause loss of control and even structural damage, and close to the ground there may not be enough time or height to recover.
Part 3 · The wake
What makes a wake strong Weight The heavier the generating aircraft, the stronger the vortices.
Speed The slower it flies, the stronger the vortices.
Configuration For a given weight and speed, strongest when clean : flaps and gear up.
Angle of attack The higher the angle of attack, the stronger the vortices.
Wingspan Sets how far apart the two vortices are.
Relative size The bigger the generator compared with you , the worse the upset. For a given weight and speed, a helicopter may make a stronger vortex.
Chapter 6 · The Three-Dimensional Wing
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Several characteristics of the generating aircraft decide how strong its wake is. Weight first: the heavier the aircraft, the more lift it is making and the stronger the vortices. Speed: the slower it flies, the higher its angle of attack and the stronger the vortices, which links straight back to the vector diagram we saw earlier. Configuration: for a given weight and speed, the vortices are strongest in the clean configuration, with gear and flaps up, because the lift is concentrated more towards the tips. Angle of attack: the higher it is, the stronger the vortices. Wingspan mainly decides how far apart the two vortices are. And as a general rule, the larger the generating aircraft relative to yours, the greater the hazard. So the worst case is heavy, slow and clean. There is also evidence that, for a given weight and speed, a helicopter can produce a stronger vortex than a fixed-wing aircraft.
Part 3 · The wake
Where the vortices go
flight path of the generating aircraft
sink, then level off
500 to 1000 ft below
can extend up to about 9 NM behind a large aircraft (distances not to scale)
about ¾ span apart
In still air the vortices stay about ¾ span apart, drift down , level off 500–1000 ft below the flight path, and can last up to about 9 NM behind a large aircraft.
Chapter 6 · The Three-Dimensional Wing
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Where do the vortices go? Typically the two trailing vortices stay about three quarters of a wingspan apart. In still air they drift slowly downward and then level off, usually between five hundred and a thousand feet below the flight path of the aircraft that made them. Behind a large aircraft they can still be present as much as nine nautical miles back. That gives two simple rules. Because the vortices sink, flying below and behind the generating aircraft puts you right where they are; you want to be at or above its flight path. And because they last for miles, time and distance separation behind heavier types really matter. The live picture of this would be dull, so this is a side view with the distances squeezed; the important thing is the shape: sink, then level off.
Part 3 · The wake
Vortices near the ground and in a crosswind
Still air
5 kt
5 kt
5 kt crosswind from the left
0 kt: stays put
10 kt
wind 5 kt
Below about 1000 ft the vortices reach the ground and move outward at about 5 kt, roughly half a span above it (viewed from behind)
A light crosswind can hold the upwind vortex over the runway. A light quartering tailwind can push vortices forward into the touchdown zone: the longest-lasting hazard.
Chapter 6 · The Three-Dimensional Wing
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
If the generating aircraft is within about a thousand feet of the ground, the vortices sink until they meet it, then spread outward at about five knots each, roughly half a span above the surface. That is the still air picture on the left, viewed from behind. Now add a light, steady crosswind of five knots from the left. The whole system drifts with the wind. The downwind vortex moves away at five plus five, ten knots. But the upwind vortex, trying to move outward into the wind at five knots, is held at about zero: it can sit over the runway. So with a light crosswind, the upwind vortex is the one that lingers. A light quartering tailwind is the worst case of all, because it can push the vortices forward into the touchdown zone. With parallel runways, wake from one runway can drift across to the other.
Part 3 · The wake
Decay and avoidance Decay Atmospheric turbulence breaks vortices up: the stronger the wind , the quicker. Most serious incidents near the ground happen in light winds .
ATC separation Reduces the probability and severity of an encounter, but does not guarantee avoidance. Take extra care behind heavier aircraft.
Stay above and upwind Picture the wake. Keep above and upwind of a preceding or crossing aircraft’s flight path, without breaking procedures.
Taking off behind a departure Lift off before the point where it rotated, and climb above and upwind of its path.
Taking off behind a landing Plan to lift off beyond the point where it touched down : its wake ended there.
Landing behind a landing Stay at or above its glide path and touch down beyond its touchdown point.
Chapter 6 · The Three-Dimensional Wing
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
How do vortices decay, and how do we avoid them? Atmospheric turbulence is the main thing that breaks them up, so the stronger the wind, the quicker they decay, and most serious incidents close to the ground happen when the wind is light. Air traffic control applies separation minima, but that only lowers the probability of an encounter and may reduce the upset; it is not a guarantee. The best defence is to picture where the wake is. Staying above and upwind of a preceding or crossing aircraft will usually keep you clear, although you should not break published procedures to do it. Taking off behind a departing heavy, lift off before its rotation point and climb above and upwind of its path. Taking off behind one that has just landed, lift off beyond the point where it touched down. Landing behind one, stay above its glide path and land beyond its touchdown point.
Part 4 · The ground
Ground effect: weaker vortices near the runway Close to the ground the vortices cannot fully develop Upwash and downwash are reduced So the effective angle of attack increases At the same α: more lift and less induced drag For the same lift: a smaller angle of attack
Out of ground effect
In ground effect
vortices weakened: less downwash, more effective α
Chapter 6 · The Three-Dimensional Wing
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
When an aircraft takes off or lands, the wing is close to the ground, and the ground gets in the way of the vortices. They cannot develop fully, so they are much weaker. Upwash ahead of the wing and downwash behind it are reduced, and because the downwash at the wing is smaller, the effective angle of attack increases. Watch the live picture as the ground comes closer: the vortices shrink. So in ground effect, at the same angle of attack, the wing produces more lift and less induced drag. Put the other way round, the same lift can be produced at a smaller angle of attack. Exam phrasing: to produce the same lift in ground effect as out of it, the aeroplane needs a lower angle of attack; and if the same angle of attack is held, lift increases and induced drag decreases.
Part 4 · The ground
How close is close? Height and induced drag
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
0%
10%
20%
30%
40%
50%
60%
70%
ratio of wing height to span (h / b)
reduction in induced drag coefficient (C L constant)
4 m: 47.6%
10 m: 23.5%
40 m: 1.4%
40 m span aircraft
at 40 m: 1.4% reduction
at 10 m: 23.5%
at 4 m: 47.6%
Big effect only within
about half a span
Low wing: closer to the
ground, more ground effect
Empirical relation; points as quoted
A large reduction in induced drag only happens within about half a span of the ground. A low-wing aircraft feels more ground effect than a high-wing one.
Chapter 6 · The Three-Dimensional Wing
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
How close does the wing have to be? This curve shows the reduction in induced drag coefficient against the height of the wing divided by its span. Take an aircraft with a forty metre span. At a height of forty metres, one span, the reduction is only about one and a half per cent, hardly noticeable. At ten metres, a quarter of the span, the reduction is about twenty-three and a half per cent. At four metres, a tenth of the span, it is almost forty-eight per cent. So a large reduction only happens within about half a span of the ground, and the last few metres make a huge difference. That is why the mounting of the wing matters: in the landing attitude a low-wing aircraft has its wing much closer to the ground than a high-wing one, so it generally feels a greater degree of ground effect.
Part 4 · The ground
Ground effect and the tailplane A low-set tailplane sits in the downwash behind the wing Ground effect reduces the downwash there Tailplane effective α increases : less download (or more up-force) Result: a nose-down pitching moment , whatever the tail camber A high (T) tail may sit outside the changing downwash
Normal downwash
download on the tailplane
downwash 8°
Downwash reduced by ground effect
less download: nose-down pitch
downwash 3°
Whatever the tailplane camber, less downwash → nose-down moment
Chapter 6 · The Three-Dimensional Wing
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ground effect also changes the pitch of the aircraft, through the tailplane. A low-set tailplane sits in the downwash behind the wing, so the air reaches it coming slightly from above, and in normal flight that usually gives a download on the tail. In ground effect the downwash is reduced. The air now reaches the tailplane less steeply from above, so its effective angle of attack increases. The download on the tail gets smaller, or the up-force gets bigger, and either way the tail rises: the aircraft pitches nose down. A useful point from the exam: it makes no difference whether the tailplane is positively cambered, negatively cambered or symmetrical; a decrease in downwash always gives a nose-down pitching moment, and an increase in downwash a nose-up one. A high-mounted tail may be outside the changing downwash and so escape most of this.
Part 4 · The ground
Effective angle of attack at the tail Air leaving the wing is not relative airflow: it has been disturbed So the tail has an effective angle of attack, to the effective airflow Flow from A gives zero; from E, F, G an increase ; from B, C, D a decrease More downwash (G → D): tail effective α decreases Less downwash (D → G): tail effective α increases
tailplane chord line
D
C
B
A
E
F
G
Airflow from above (more downwash):
smaller effective angle of attack
Airflow from below (less downwash):
larger effective angle of attack
Chapter 6 · The Three-Dimensional Wing
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Strictly speaking, a tailplane does not have an angle of attack in the textbook sense. Angle of attack is measured to the relative airflow, which must be undisturbed, parallel and opposite to the flight path, with a magnitude of the true airspeed. The air leaving the wing has been bent down and slowed, so it is effective airflow, and the tail has an effective angle of attack. Look at the seven directions. Air arriving from A, along the chord, gives zero effective angle. Air from E, F or G, coming from further below, gives an increasing effective angle. Air from B, C or D, coming from further above, gives a decreasing one. We do not talk about a negative angle of attack here, only an increase or decrease. So more downwash, moving from G towards D, decreases the tail effective angle of attack, and less downwash increases it.
Part 4 · The ground
Entering ground effect on landing
0°
4°
8°
12°
16°
0.0
0.5
1.0
1.5
C L
out of ground effect
in ground effect
In ground effect the same angle of attack
gives more C L, and the same C L needs less α.
Induced drag falls: less thrust needed.
Illustrative lift-curve slopes
Float C L up and induced drag down at the same attitude: the aircraft floats ; extra speed means a long float.
Balloon Less thrust is needed: without reducing power it may climb above the glide path .
Pitch Less downwash at the tail: nose-down moment; more back pressure is needed.
Instruments Static pressure usually rises : ASI and altimeter under-read . If slow at high α, it may stall: heavy landing.
Chapter 6 · The Three-Dimensional Wing
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Picture an approach at constant C L and indicated airspeed as the aircraft descends into ground effect. The reduced downwash raises the effective angle of attack, so the same lift coefficient needs a smaller wing angle of attack, as the steeper lift curve shows. If the pilot holds the pitch attitude, lift rises and induced drag falls, and there is a floating sensation; any excess speed leads to a long float, because the aircraft decelerates more slowly. With less thrust needed, it may balloon above the glide path unless the power is reduced. If the speed has been allowed to decay on short final and the sink is stopped by pulling to a high angle of attack, the wing could stall on entering ground effect, giving a heavy landing. The tail sees less downwash, giving a nose-down moment, so more back pressure is needed. Finally, the static port usually senses a higher pressure, so the ASI and altimeter under-read.
Part 4 · The ground
Leaving ground effect after take-off Lift and drag C L falls and induced drag rises : a higher α and more thrust are needed for the same lift.
Pitch More downwash at the tail gives a nose-up moment: ease the back pressure . Risk of over-rotation and tail strike .
Instruments Static pressure usually falls : ASI and altimeter over-read .
Settling back Lifted off too slowly in ground effect, it may sink back onto the runway after leaving it. Use the correct speeds .
Chapter 6 · The Three-Dimensional Wing
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Climbing out of ground effect after take-off does roughly the opposite. Assume constant C L and indicated airspeed. As the wing climbs away, the vortices develop fully, the downwash grows, and C L falls while induced drag rises; so the aircraft needs a higher angle of attack to keep the same lift, and more thrust. The increased downwash at the tail generally gives a nose-up pitching moment, so the pilot may need to reduce the back pressure; if not, the nose-up moment can cause an inadvertent over-rotation and a tail strike. The position error changes too, and in most cases the static pressure falls, so the airspeed indicator and altimeter over-read. Most important of all: an aircraft can become airborne in ground effect at a speed and angle of attack that will not support it once it climbs out, and it may settle back onto the runway. That is why the correct take-off speeds matter.
Summary
What to take into the exam Terms AR = b ÷ c̄ = b² ÷ S. Taper = C T ÷ C R. Sweep on the 25% chord line. MAC through the centre of area.
Vortices From behind: left clockwise, right anticlockwise. Outward, up and round the tip. Stronger at high α, low IAS.
Induced drag Downwash lowers the effective α; lift tilts back. More α needed, more drag. Less with high AR.
Lift distribution Zero at the tips. Elliptical: least induced drag. Rectangular: root first. Washout unloads the tips.
Wake Nosewheel up to nosewheel down. Heavy, slow, clean worst. ¾ span apart, sink 500–1000 ft, up to 9 NM.
Wake near ground Out at about 5 kt. Light crosswind holds the upwind vortex. Light quartering tailwind worst. Stay above and upwind.
Ground effect Within about ½ span. Less downwash: more C L, less C D i, smaller α for the same lift. Low wing more.
In and out Entering: float, nose down, ASI under-reads. Leaving: more α and thrust, nose up, ASI over-reads, may settle.
Chapter 6 · The Three-Dimensional Wing
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the key points. Aspect ratio is span over average chord, or span squared over area; taper ratio is tip chord over root chord. Seen from behind, the left tip vortex turns clockwise and the right anticlockwise, with air going outward, upward and round the tip, and vortices are strongest at high angle of attack and low speed. Induced downwash lowers the effective angle of attack and tilts the lift back, and the rearward part is induced drag, which a high aspect ratio reduces. Lift falls to zero at the tips, and an elliptical distribution gives the least induced drag. Wake is generated from nosewheel lift-off to touchdown, is worst behind heavy, slow, clean aircraft, sinks five hundred to a thousand feet and lasts up to nine miles. In ground effect, induced drag falls and lift rises; entering, expect a float and a nose-down moment; leaving, expect more drag, a nose-up moment, and the risk of settling back.