N 3 6 E 12 15 S 21 24 W 30 33 RMI: needle → NDB NDBRadio Navigation · Chapter 7
Automatic Direction Finder An aircraft's ADF points at a non-directional beacon on the ground: how the needle finds it, how to track with it, and what makes it lie.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ADF in the aircraft and the NDB on the ground are the oldest radio navigation pair still in daily use, for en-route bearings, holding and non-precision approaches. Four parts: how the ADF finds the beacon; the beacon and the set; tracking with the needle; and errors, range and accuracy.
Chapter roadmap
What this chapter covers 01
How ADF works Loop, sense aerial, cardioid, switched cardioids, goniometer.
02
Beacon and set Frequencies, NDB types, BFO and emissions, RBI and RMI.
03
Tracking Homing, inbound and outbound tracks, drift assessment, holding.
04
Errors and range Static, night effect, coast, quadrantal, dip; range and ±5°.
Chapter 7 · Automatic Direction Finder
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Four parts: the principle, the beacon and the airborne set, tracking technique, and the errors and range.
Introduction
A beacon on the ground, a needle in the cockpit NDB : ground transmitter, LF/MF , vertically polarised, radiates in all directionsADF : tune and identify the NDB; the needle points to itThe ADF measures the bearing relative to the aircraft's fore-aft axis Uses: en route bearings, homing, holding, non-precision approaches Cone of silence overhead: no signal; it widens with height cone of silence0 3 6 9 12 15 18 21 24 27 30 33 RBI LF/MF · vertically polarised · surface wave
Chapter 7 · Automatic Direction Finder
03
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ADF in the aircraft works with a simple LF or MF non-directional beacon on the ground. The NDB radiates vertically polarised signals in all directions. Tune and identify it, and the ADF needle points to it: the bearing is measured relative to the aircraft's fore and aft axis. It's used for en-route bearings, homing, holding and non-precision approaches, and is still the only instrument approach at some aerodromes. Directly overhead there's a cone of silence, which gets wider the higher you are.
01
How ADF works A loop finds two nulls; a sense aerial picks the right one.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Principle of operation
The loop aerial: a figure of eight The wave reaches the loop's two vertical sides at different times: a phase difference induces a voltage Rotate the loop: the voltage falls to zero when the loop is at right angles to the wave The polar diagram is a figure of eight with two nulls Turn to a null and you have the line of the beacon, but not which end: 180° ambiguity from the NDBNULL: loop faces the NDB NULL again, 180° later volts 0 = null figure of eight: two nulls, 180° apart
Chapter 7 · Automatic Direction Finder
05
e-books by eatpl.in · © 2026 · Do not copy or distribute
A loop aerial in the path of the wave has a voltage induced because the wave arrives at its two vertical sides with a phase difference. As the loop rotates, the voltage falls to zero when the loop is perpendicular to the wave, then builds again in the opposite sense. The polar diagram is a figure of eight with two nulls. Turning the loop to a null gives the line of the beacon, but not which way along it: a 180 degree ambiguity, and an automatic system can't resolve it with a loop alone.
Resolving the ambiguity
Add a sense aerial: loop + circle = cardioid loop + sense aerial = single null cardioid the cardioid's null is blunt: it only picks which loop null is correctThe cardioid's single null is ill-defined . Logic picks the correct loop null : the one where turning the loop clockwise increases the cardioid signal.
Chapter 7 · Automatic Direction Finder
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
To resolve the ambiguity a simple dipole, the sense aerial, is added. Its polar diagram is a circle. Its signal is combined as if it were in the middle of the loop, in phase with one side of the loop. The result is a cardioid with a single null. That null is blunt and not accurate enough by itself, so a logic circuit uses it only to choose the correct loop null: the one where rotating the loop clockwise makes the cardioid signal increase.
Meeting ±5°
Switched cardioids and a fixed loop One cardioid isn't accurate enough for ICAO's ±5° Reverse the sense aerial: a right-hand cardioid; switch between the two at about 120 Hz Where the two are equal is a sharp bearing No rotating loop outside: a fixed loop of four elements (fore-aft and athwartships) feeds a goniometer The goniometer's search coil turns to the null and drives the needle to the NDB switched L / R cardioids (about 120 Hz) fixed 4-element loop + goniometer search coil
Chapter 7 · Automatic Direction Finder
07
e-books by eatpl.in · © 2026 · Do not copy or distribute
A single cardioid isn't accurate enough to meet the ICAO requirement of plus or minus 5 degrees. So the sense aerial's polarity is reversed to make a right-hand cardioid as well, and the receiver switches rapidly between left and right cardioids, about 120 times a second; the point where they're equal is precise. And a rotating loop outside the aircraft isn't practical, so the loop is fixed, with four elements, two fore and aft and two athwartships. Their fields are reproduced inside a goniometer, and a search coil there finds the null and drives the needle.
02
The beacon and the set Where NDBs live on the dial, how to hear them, and how the needle is shown.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Frequencies and types of NDB
190–1750 kHz, surface wave Allocated 190–1750 kHz (LF and MF) Propagation by surface wave , so most NDBs are 250–450 kHz Locator (L) : low power, 10–25 nm, for approaches; often co-located with ILS markers; may only operate in aerodrome hoursEn route : 50 nm or more (hundreds over oceans); homing, holding, airways 190 LF | MF 300 1750 kHz most NDBs 250–450 Locator (L) 10–25 nm · approach En route 50 nm or more
Chapter 7 · Automatic Direction Finder
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
NDBs are allocated 190 to 1750 kilohertz, in the LF and MF bands. They use the surface wave, so most sit between about 250 and 450 kilohertz. Two types: the locator, a low-powered NDB for approach procedures, often co-located with the outer or middle marker of an ILS, with a range of 10 to 25 miles and perhaps only available during aerodrome hours; and en-route NDBs with 50 miles or more, several hundred over oceans, for homing, holding and airways.
Aircraft equipment and the BFO
Hearing an unmodulated carrier The set: loop aerial, sense aerial, control unit, receiver, display . NDBs have a 2 or 3 letter ident and one of two emissions:
Emission Tune Identify Monitor N0N A1A : keyed carrierBFO ON BFO ON BFO ON N0N A2A : keyed tone (AM)BFO ON OFF OFF
The BFO (beat frequency oscillator, sometimes TONE) mixes an offset with the carrier to make an audible tone, about 400 or 1020 Hz.
N0N unmodulated carrier A1A carrier keyed (Morse) A2A keyed tone, AM
Chapter 7 · Automatic Direction Finder
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The aircraft equipment is a loop aerial, a sense aerial, a control unit, a receiver and a display. NDBs identify with two or three letters, with one of two emissions. N0N is the unmodulated carrier, which a normal receiver can't hear, so the ADF has a beat frequency oscillator that mixes in an offset to produce a tone. A1A is the carrier keyed on and off, so the BFO must be ON to tune, identify and monitor. A2A is an amplitude-modulated tone you can hear normally: BFO ON to tune, then OFF to identify and monitor.
Presentation
RBI and RMI: both show relative bearing RBI : card fixed, 0 at the nose: reads relative bearing RMI : card driven by the compass, so the needle reads magnetic bearing to the NDB (QDM); tail = QDRQDM = heading + relative bearing (− 360 if over)Heading 300, RB 136: 300 + 136 − 360 = 076 0 3 6 9 12 15 18 21 24 27 30 33 N 3 6 E 12 15 S 21 24 W 30 33 RBI: card fixed, 0 = nose RMI: card = compass HDG300 300 315 330 345 345 330 300 285 270 270 285 RB136 136 121 106 091 091 106 136 151 166 166 151 QDM = HDG + RB = 076 QDR 256
Chapter 7 · Automatic Direction Finder
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The information can be shown on a relative bearing indicator or a radio magnetic indicator; either way the ADF provides relative bearing. The RBI's card is fixed with zero at the nose, so you read relative bearing directly. The RMI's card is driven by the compass, so the same needle reads magnetic bearing to the beacon, the QDM, and its tail the QDR. Magnetic bearing is heading plus relative bearing: heading 300, relative bearing 136, gives 436 minus 360, 076. When plotting, remember the bearing is measured at the aircraft, so apply variation there and allow for convergency.
03
Tracking with the needle Homing, tracking in and out, finding the drift, and holding.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Inbound tracking
Homing curves; tracking stays straight Zero wind: heading = track, needle on 000 Crosswind and the needle kept on the nose = homing : a curved path, arriving downwind To track , lay off the expected drift: the needle sits off the nose by the drift Starboard drift: subtract from track; port drift: add wind → homing: curves downwind tracking: drift laid off
Chapter 7 · Automatic Direction Finder
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
In zero wind, heading equals track and the needle sits on 000. In a crosswind, if you keep the needle on the nose you're homing, not tracking: the wind keeps pushing you off, you keep turning towards the beacon, and the path curves round to arrive from downwind. To fly a straight track you lay off the drift: with starboard drift subtract it from the track to get the heading; with port drift add it. The needle then sits off the nose by the drift angle, on the upwind side.
Maintaining an inbound track
Track 080 in a crosswind 20° starboard drift : heading 080 − 20 = 060 ; needle 020 28° port drift : heading 080 + 28 = 108 ; needle 332 Inbound, the needle points into wind by the drift Needle steady = drift correctly allowed track 080 track 0800 3 6 9 12 15 18 21 24 27 30 33 RBIHDG 060 · 20° stbd drift HDG 108 · 28° port drift RB 020 RB 332 needle steady = drift allowed
Chapter 7 · Automatic Direction Finder
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
To hold track 080 inbound with 20 degrees of starboard drift, subtract it: heading 060, and the needle shows 020, 20 right of the nose. With 28 degrees of port drift, add it: heading 108, needle 332, 28 left. Inbound, the head of the needle is offset to the upwind side by the drift. If it stays put, you've got the drift right.
Outbound tracking
Tail of the needle on the track track 260 track 100 track 0900 3 6 9 12 15 18 21 24 27 30 33 RBIHDG 260 · no drift HDG 077 · 23° stbd HDG 110 · 20° port RB 180 RB 203 RB 160 needle steady = drift allowedOutbound, RB = 180 ± drift: starboard drift (heading left of track) makes it more than 180; port drift less .
Chapter 7 · Automatic Direction Finder
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Outbound in zero wind: heading 260, needle 180. Track 100 with 23 degrees of starboard drift: subtract, heading 077, and the needle reads 203. Track 090 with 20 port: add, heading 110, needle 160. Outbound the relative bearing is 180 plus or minus the drift: more than 180 when you're heading left of track for starboard drift, less for port.
Drift assessment inbound
Find the drift, regain, then hold Fly the track with the NDB dead ahead (000 ) and hold heading Needle moves right (RB increasing ): port drift Turn 30° right to regain: on track when RB = 330 Assume a drift (say 10° port): new heading; RB becomes 350 RB steady: drift right. Changes: adjust again 1 · RB 000, hold heading 2 · RB increasing: port drift 3 · turn 30° right 4 · RB 330: back on track 5 · allow 10° port drift: RB 350, keep it there
Chapter 7 · Automatic Direction Finder
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
To find the drift inbound, fly the track with the beacon dead ahead and hold the heading. Watch the needle. If the relative bearing increases, the wind is carrying you to the left: port drift. Turn, say, 30 degrees right to regain; you're back on track when the relative bearing reads 330. Then assume a drift, say 10 degrees port, and take up track plus 10: the relative bearing becomes 350. If it stays there all the way in, you've assessed the drift correctly; if it moves, adjust again.
Drift assessment outbound
Read it from overhead on a steady heading From overhead on a steady heading: 180 = no drift 190 = 10° starboard drift; 170 = 10° portAlter 30° to regain: on track at RB 210 or 150 Then set heading for the assessed drift 180: zero drift 190: 10° stbd drift 170: 10° port drift steady heading from overhead
Chapter 7 · Automatic Direction Finder
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Outbound, the drift is read from the tail. Hold a steady heading from directly overhead: 180 means no drift; 190 means 10 degrees starboard drift; 170 means 10 port. Having assessed it, alter heading 30 degrees to regain the track, which you reach when the needle reads 210 or 150, then take up a heading that allows for the drift you measured.
Holding and approaches
Stacks over a beacon Traffic or weather delays: aircraft wait in a holding pattern (the stack) over a beacon Race-track pattern, levels 1000 ft apart; step down as the bottom clears Many aerodromes have an NDB approach ; sometimes the only instrument approach NDB(L) often co-located with ILS markers or used with DME FL 30 FL 40 FL 50 FL 60 1000 ft apart NDB holding fix
Chapter 7 · Automatic Direction Finder
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
When traffic or weather delays landing, ATC sends aircraft to a holding area, a stack over a radio beacon. Each aircraft flies a race-track pattern, separated vertically by at least 1000 feet, and steps down as the level below clears, until it leaves the bottom to approach. Many aerodromes publish NDB approaches, sometimes the only instrument approach available; the locator may also be used with DME or other aids.
04
Errors, range and accuracy Why the needle wanders, and how far you can trust it.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Static interference
Precipitation static and thunderstorms Precipitation static : rain and ice hitting the airframe; lower signal-to-noise, wandering needle , hissThunderstorms : discharges across LF/MF; loud crackle and the needle swings to the Cb Several cells: it may point at them for long periods Cb about: the ADF is most use for showing where the storms are Cb0 3 6 9 12 15 18 21 24 27 30 33 needle jumps to the Cb NDB
Chapter 7 · Automatic Direction Finder
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Static interference comes in two kinds. Precipitation static is generated by water droplets and ice crystals hitting the aircraft; it lowers the signal to noise ratio, so the needle wanders and there's a hiss, often on VHF too. Thunderstorms produce huge static discharges across the LF and MF bands: a loud crackle, and the needle swings to point at the cumulonimbus. With several active cells it can point at them for long periods. During Cb activity the most sensible use of the ADF may be to show where the active cells are.
Night effect
Sky wave contaminates the surface wave Day: the D layer absorbs LF/MF sky waves Night: D layer gone; sky waves return and mix with the surface wave Phase interference, and currents in the loop's horizontal members Significant from 70–100 nm ; worst at dawn and dusk Fading audio, hunting needle D layer: absorbs by day, gone at night E layer: reflects at night sky wave surface wave0 3 6 9 12 15 18 21 24 27 30 33 day: steady day: steady day: steady day: steady night: hunts night: hunts night: hunts night: hunts night: hunts night: hunts night: hunts night: hunts night: hunts day: steady day: steady day: steady
Chapter 7 · Automatic Direction Finder
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
By day the D region absorbs LF and MF signals. At night it disappears, and sky waves reflected from higher up arrive along with the surface wave. They interfere in phase, and they induce currents in the horizontal elements of the loop. Short vertical elements and screening reduce it but don't remove it. It becomes significant 70 to 100 miles from the NDB, and is worst around dawn and dusk when the ionosphere is changing: fading audio and a hunting needle. Minimise it by identifying positively, rechecking tuning and ident, avoiding use within an hour of sunrise or sunset, using NDBs within their promulgated daytime range, and cross-checking.
Coastal refraction
Faster over water, bent at the coast Less attenuation over water: the wave speeds up and bends away from the normal Negligible at 90° to the coast; worse the more oblique Over the sea, the plotted position is closer to the coast than you are Minimise: NDBs on or near the coast , fly higher , signals crossing at 90° LAND SEA normal apparent line faster over water: bends away from the normal
Chapter 7 · Automatic Direction Finder
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Radio waves travel faster over water, because there's less absorption than over land. So as the wavefront crosses the coast it bends, away from the normal and towards the coastline. At 90 degrees to the coast there's no bending; it gets worse the more oblique the crossing. An aircraft over the sea using an inland beacon gets a bearing that puts it closer to the coast than it really is. Reduce it by using NDBs on or near the coast, flying higher, and using signals that cross the coast close to 90 degrees.
More errors
Quadrantal, dip, terrain and stations
Quadrantal Fuselage bends signals fore-aft: max at RB 045, 135, 225, 315 .
Dip (bank) Horizontal loop members pick up signal: error only when not level .
Mountain effect Reflection and diffraction; worse low , so fly higher.
Station interference DOC protects by day; at night distant stations interfere.
No failure warning Most ADFs have no flag: monitor the ident all the time.
Precipitation Rain and snow cut range and accuracy.
045 135 225 315 max error in the quadrants
Chapter 7 · Automatic Direction Finder
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
More error sources. Quadrantal error: the airframe's strong fore-and-aft electrical field bends incoming signals towards the fore and aft axis, most on relative bearings of 045, 135, 225 and 315; manufacturers correct for it, older sets are swung. Dip: in a bank the horizontal members of the loop pick up signal, so there's an error whenever you're not level. Mountain effect: reflections and diffraction, worse at low altitude. Station interference: within the DOC you're protected by day, but not at night when distant stations arrive by sky wave. And most ADFs have no failure warning, so identify and monitor the beacon continuously, especially on an approach.
Range and accuracy
Power, water, frequency Range (nm) ≈ 3 √P over water · 2 √P over land (P in watts)
Range ∝ √power: 4× the power for 2× the range 100 W: about 30 nm over water, 20 nm over land Lower frequency: more surface wave, more range Precipitation (snow too) reduces range and accuracy N0N A1A reaches further than A2A, but ICAO recommends A2A for long-range beacons
Accuracy ±5° within the DOC, by day only : the measured bearing, not including compass error.
DOC Based on a daytime protection ratio of 3:1 wanted to unwanted. Beyond it, or at night, errors grow.
Chapter 7 · Automatic Direction Finder
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Range depends mainly on power: it's proportional to the square root of the power, so doubling the range needs four times the power. As a rule of thumb, 3 root P nautical miles over water and 2 root P over land: 100 watts gives about 30 miles over water, 20 over land. Lower frequencies give more surface wave and more range; precipitation, including snow, cuts range and accuracy. The accuracy is plus or minus 5 degrees within the designated operational coverage, by day only. The DOC is based on a daytime protection ratio of 3 to 1.
Summary
What to take into the exam Principle Loop (figure 8, two nulls) + sense (circle) = cardioid; switched cardioids; fixed loop + goniometer.
NDB 190–1750 kHz, surface wave. Locator 10–25 nm; en route 50 nm+.
BFO A1A: ON for tune, ident, monitor. A2A: ON to tune, OFF after.
Displays RBI: relative. RMI: QDM = HDG + RB; tail = QDR.
Tracking Stbd drift: subtract; port: add. Homing curves downwind. Outbound RB = 180 ± drift.
Errors Static, Cb, night (dawn/dusk), coast (closer to coast), quadrantal (045…), dip, mountain, stations, no flag. ±5° by day.
Chapter 7 · Automatic Direction Finder
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six points: the principle; the NDB frequencies and types; BFO use for A1A and A2A; the RBI and RMI with QDM equals heading plus relative bearing; tracking with drift; and the errors, with plus or minus 5 degrees by day within the DOC.
Practice · Questions 1–7
Try these 1. Coastal refraction, which affects ADF bearings: (a) is most marked at night (b) can be minimised by using beacons well inland (c) can be minimised by taking bearings where the signal crosses the coast at right angles (d) is most marked an hour either side of sunrise and sunset
2. Tracking 050(T) from NDB A to NDB B, heading 060(T). RB of A is 180, of B is 330. The aircraft is: (a) port of track, nearer A (b) port, nearer B (c) starboard, nearer A (d) starboard, nearer B
3. ADF quadrantal error is caused by: (a) static and St Elmo's fire (b) the fuselage reflecting and re-radiating the signal (c) station interference or night effect (d) signals speeding up from land to water
4. The accuracy of ADF bearings by day within the DOC is: (a) ±3° (b) ±5° (c) ±6° (d) ±10°
5. To tune, identify and monitor a N0N A1A NDB the BFO should be: (a) on, on, off (b) on, on, on (c) on, off, off (d) off, off, off
6. Coastal refraction errors in ADF position lines may be reduced by: (a) beacons well inland (b) only using beacons in the DOC (c) choosing N0N A2A beacons (d) choosing beacons on or near the coast
7. Tracking away from an NDB on 023(T), drift 8° port, variation 10°W. What does the RMI show?
Chapter 7 · Automatic Direction Finder
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 1 to 7. Questions 7 and 10 ask you to picture the RMI: work out the heading first, then where each needle points.
Practice · Questions 8–14
Try these 8. The BFO with a N0N A1A NDB should be used: (a) on for tuning and ident, off to monitor (b) on to tune, off for ident and monitor (c) off throughout (d) on for tuning, ident and monitoring
9. The 3:1 protection ratio within the DOC by day cannot be guaranteed at night because of: (a) long-range sky wave interference from other transmitters (b) sky wave from your own NDB (c) the larger skip distance (d) sporadic E
10. Two-needle RMI. Outbound from NDB Y on 126(M), drift 14° port; report crossing QDR 022 from NDB Z. What does the RMI show?
11. Within an NDB's promulgated range, interference from other NDBs should not cause errors greater than: (a) ±5° by day (b) ±10° by night (c) ±6° by day (d) ±5° by night
12. The range promulgated for UK NDBs is the range: (a) with a 3:1 ratio day and night (b) for bearings on 95% of occasions (c) within which bearings by day should be within 5° (d) with sky wave protection guaranteed
13. To resolve the loop's 180° ambiguity its polar diagram is combined with a sense aerial ___ to give a ___ whose single null takes the needle the shortest way to the correct ___: (a) at the aircraft, cardioid, radial (b) at the transmitter, limaçon, bearing (c) at the aircraft, limaçon, bearing (d) at the aircraft, cardioid, bearing
14. The protection ratio within the DOC of UK NDBs applies: (a) by day only (b) by night only (c) day and night (d) at dawn and dusk
Chapter 7 · Automatic Direction Finder
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Practice · Questions 15–21
Try these 15. Coastal refraction is caused by the signal ___ at the coast and bending ___ the normal: (a) accelerating, towards (b) decelerating, towards (c) accelerating, away from (d) decelerating, away from
16. Night effect is most pronounced: (a) on long winter nights (b) at low altitude (c) at high altitude (d) at dusk and dawn
17. Loop and sense signals combined give a polar diagram that is: (a) a limaçon (b) a cardioid (c) a figure of eight (d) circular
18. Over the sea with an inland NDB, the plotted position compared with the actual position is: (a) further from the coast (b) closer to the coast (c) the same (d) wrong because the wave slows
19. Heading 235(M), RMI reads 090. Any quadrantal error is likely to be: (a) a maximum (b) very small (c) zero, it affects only the RBI (d) zero, it affects only VOR
20. The main propagation path for NDB/ADF is: (a) sky wave (b) surface wave (c) direct wave (d) ducted wave
21. Heading 189(T). Quadrantal error is greatest if the NDB bears: (a) 234(T) (b) 279(T) (c) 225(T) (d) 145(T)
Chapter 7 · Automatic Direction Finder
28
e-books by eatpl.in · © 2026 · Do not copy or distribute
Practice · Answers
Answers and working Q Ans Why 1 c No bending at 90° to the coast 2 d Starboard of track, nearer B 3 b Fuselage re-radiates 4 b ±5° by day in the DOC 5 b A1A: BFO on throughout 6 d Beacons on or near the coast 7 – HDG 041(M); head 213, tail 033 8 d BFO on for all three 9 a Sky wave from distant stations 10 – HDG 140; Y head 306; Z head 202 11 a ±5° by day
Q Ans Why 12 c Bearings within 5° by day 13 d At the aircraft, cardioid, bearing 14 a By day only 15 c Accelerates, bends away 16 d Dusk and dawn 17 b A cardioid 18 b Closer to the coast 19 a RB 215: near the 225 quadrant 20 b Surface wave 21 a 234 − 189 = 045 relative
Chapter 7 · Automatic Direction Finder
29
e-books by eatpl.in · © 2026 · Do not copy or distribute
Question 2: A is behind you at relative 180, so it bears 240 true and you're on its 060 radial, right of the 050 track: starboard. B at 330 relative bears 030; the same distance off track subtends 20 degrees from B but only 10 from A, so you're nearer B. Question 7: 023 plus 8 port is 031 true, plus 10 west is 041 magnetic; the needle head reads 213. Question 10: heading 140, needle Y on 306, needle Z on 202.
Drag the aircraft: RBI and RMI live, two NDBs Fly inbound and outbound with wind; home or track Watch the loop, cardioids and goniometer find the null Switch on night effect, Cb, quadrantal error; range calculator All 21 exam questions Open the ADF Lab →
N 3 6 E 12 15 S 21 24 W 30 33 QDM 100 = HDG 060 + RB 040
Chapter 7 · Automatic Direction Finder
30
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ADF Lab: read the needles anywhere, fly with wind, see how the aerial works, and switch the errors on and off.
eatpl.in · Radio Navigation · Chapter 7
ADF Lab
Read the RBI and RMI anywhere round an NDB, fly with wind, see how the aerial finds the null, and switch on the errors.
Needles Fly Aerial Errors Practice
Loop, sense and cardioid
The search coil hunts for the loop null; the cardioids choose the correct one of the two.
All the chapter's questions. Set each up, read the answer in the lab, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.