Radio Navigation · Chapter 4
Antennae How aerials radiate and receive: dipoles and Marconi aerials, feeders, polar diagrams, directivity, and the aerials of ILS, ADF and radar.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aerials, or antennae, are how radio energy is radiated and received. The type depends on the job. This chapter covers what all aerials share, then the special aerials used by particular navigation systems.
Chapter roadmap
What this chapter covers 01
Basic aerials Half-wave dipole and Marconi aerial, ideal length, loading units.
02
Feeders and patterns From wire to waveguide, and how polar diagrams describe radiation.
03
Directivity Reflectors and directors, sidelobes, ILS and loop aerials, dishes and slotted arrays.
Chapter 4 · Antennae
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: the two basic aerials and how long they should be, feeders and polar diagrams, then directional aerials, including those used by ILS, ADF and radar.
01
Basic aerials Half a wavelength, or a quarter on a metal surface.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Basic principles
Dipole and Marconi aerials Half-wave dipole : fed at the centre; radiates in all directions perpendicular to the aerialMarconi (quarter-wave): mounted on, but insulated from, a metal surface that acts as the other half of a dipoleMarconi aerials are used on aircraft: better aerodynamics feed ½ λ Half-wave dipole metal surface (the other half) ¼ λ Marconi (quarter-wave)
Chapter 4 · Antennae
04
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two basic aerials. The half-wave dipole is fed at its centre and radiates in all directions at right angles to the aerial. The Marconi, or quarter-wave, aerial sits on a metal surface, insulated from it; the surface acts as the second half of the dipole. Radiation is again perpendicular to the aerial. Aircraft use Marconi aerials because they are aerodynamically better.
Aerial length
Half or quarter of λ, times 0.95 Best efficiency when the aerial is ½ λ (dipole) or ¼ λ (Marconi) Radio waves travel at about 95% of free-space speed in metal So the aerial is 0.95 × ½ λ, or 0.95 × ¼ λ Dipole = 0.95 × λ ÷ 2 · Marconi = 0.95 × λ ÷ 4
Example λ Ideal length Marconi, 125 MHz 2.4 m 0.95 × 0.6 = 57 cm Marconi, 406 MHz 0.739 m 0.95 × 0.185 = 17.5 cm Dipole, 75 MHz 4 m 0.95 × 2 = 1.9 m
Chapter 4 · Antennae
05
e-books by eatpl.in · © 2026 · Do not copy or distribute
For maximum efficiency an aerial should be half or a quarter of the wavelength. But radio waves slow down in a denser medium: in metal they travel at about 95 percent of their free-space speed. So the aerial is 95 percent of the half or quarter wavelength. A Marconi aerial for 125 megahertz: wavelength 2.4 metres, a quarter is 60 centimetres, times 0.95 is 57. A common statement says 0.95 times lambda, but the quarter is implied. 406 megahertz gives 17.5 centimetres; a 75 megahertz dipole 1.9 metres.
Loaded aerials
An aerial loading unit makes a short aerial efficient
The problem VHF R/T wavelengths are 2.19–2.54 m, so the ideal Marconi length varies from about 52 to 60 cm . Aircraft aerials are only 20–30 cm , and an adjustable aerial is impractical.
The fix An aerial loading unit (ALU) between the radio and the aerial samples the signal and balances it with capacitors and resistors for maximum efficiency.
Chapter 4 · Antennae
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aeronautical VHF voice runs from wavelengths of 2.19 to 2.54 metres, so the perfect aerial would need to vary from about 52 to 60 centimetres. Making it adjustable would be a serious technical problem, and real aircraft aerials are only 20 to 30 centimetres anyway. So an aerial loading unit is fitted between the radio and the aerial; it samples the signal and, through capacitors and resistors, balances it for maximum efficiency.
02
Feeders and polar diagrams Getting energy to the aerial, and drawing where it goes.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aerial feeders
Higher frequency, better feeder LF · MF Single wire HF · VHF Twin wire UHF Coaxial cable Upper UHF · SHF · EHF hollow · width ½ λ WaveguideA waveguide is a hollow rectangular metal tube whose internal width is half the wavelength . At these frequencies dipole and Marconi aerials can't be used.
Chapter 4 · Antennae
08
e-books by eatpl.in · © 2026 · Do not copy or distribute
The feeder carries energy between the aerial and the radio, and losses rise with frequency. At LF and MF a single wire is fine. In HF and VHF a twin-wire feeder is more efficient. At UHF those losses become unacceptable and coaxial cable is used. In the upper UHF band and in SHF and EHF, dipoles and Marconi aerials can't be used and a waveguide carries the energy: a hollow rectangular metal tube whose internal dimension is half the wavelength.
Polar diagrams
A line joining points of equal signal strength Shows the radiation (or reception) pattern of an aerial A dipole radiates most at right angles to itself and nothing off the ends In 3-D that is a torus (doughnut) round the aerial Usually drawn as a plan view in the plane of radiation Side view: torus cross-section no radiation off the ends Plan view: omnidirectional
Chapter 4 · Antennae
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
A polar diagram shows an aerial's radiation or reception pattern: a line joining all points of equal signal strength, usually drawn as a plan view of the plane of radiation. The same pattern applies to reception. A dipole radiates most at right angles to itself, less towards the ends and nothing straight off the ends. In three dimensions that's a torus centred on the aerial. Looking down the aerial, the plan view is a circle: omnidirectional.
03
Directivity Concentrating energy in one direction, at the price of sidelobes.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Directivity
A reflector a quarter-wave behind Radar, ILS, MLS and others need directional aerials Simplest way: add parasitic elements A rod 5% longer than the aerial, ¼ λ behind it, acts as a reflector It re-radiates 180° out of phase: no signal behind, more in front dipole + reflector
Chapter 4 · Antennae
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many systems need directional radiation or reception. The simplest way is parasitic elements. A metal rod 5 percent longer than the aerial, placed a quarter wavelength behind it in the same plane, acts as a reflector. It re-radiates the energy 180 degrees out of phase, so there's no signal behind the reflector and more in front.
Directors
A stronger beam, but unwanted sidelobes Directors in front of the aerial are shorter than it; they focus the signalThe familiar TV aerial (a Yagi array) Directivity's price: sidelobes that transmit and receive unwanted signals Ghosting on TV; real problems for SSR, ILS and primary radar Exam: a disadvantage of directivity is sidelobes .
reflector + aerial + 4 directors
Chapter 4 · Antennae
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Adding directors in front of the aerial, each shorter than the aerial, focuses the signal further: everyone knows this as the TV aerial. It gives a stronger signal than a simple dipole. But directivity has a price: as well as the main beam you get sidelobes, which transmit and receive unwanted signals. On TV they cause ghosting from reflections off buildings. In SSR and ILS they cause major problems that have to be designed out, and they trouble primary radar too.
Other systems
ILS localiser and the ADF loop ILS localiser: two narrow lobesAn array of 16 or 24 aerials in line, ½ λ apart, gives two narrow, symmetrical beams either side of the centreline.
ADF loop: figure of eightEdge-on to the wave the two sides' currents differ: output. Face-on they cancel: two nulls , used to find direction (Chapter 7).
Chapter 4 · Antennae
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ILS localiser extends the idea: a line of 16 or 24 aerials spaced half a wavelength apart, fed in a special way, produces two narrow symmetrical beams close to the runway centreline. The ADF uses a loop aerial. When the loop is aligned with the incoming wave, the signals in its two vertical sides are out of phase and a current flows. At right angles to the wave the induced currents are equal and cancel, giving zero output. The resulting figure-of-eight has two distinct nulls, which tell you the direction of the wave. More in Chapter 7.
Radar aerials
A horn at the focus of a parabolic reflector UHF and SHF: the end of the waveguide is the aerial Placed at the focus of a parabolic reflector to form a narrow beam The feed isn't a perfect point, so the beam diverges slightly and has sidelobes Beamwidth (°) = 70 × λ ÷ D
Narrow beam → big reflector, short wavelength, or both. 3 cm radar, 1 m dish: 70 × 0.03 ÷ 1 = 2.1°
horn at focus beam diverges slightly parabolic reflector, diameter D
Chapter 4 · Antennae
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Radar works in the UHF and SHF bands, where waveguides carry the energy and the end of the waveguide is the aerial. To make it directional it sits at the focal point of a parabolic reflector, which focuses the energy into a narrow beam. In theory a pencil beam; in practice the feed is far bigger than a point, so the beam diverges a little and uneven reflection creates sidelobes strong enough to give real returns. The beamwidth is 70 times the wavelength over the reflector diameter: a narrow beam needs a large reflector or a short wavelength.
Phased array / slotted antenna
A flat plate full of slots Waveguide-sized slots cut in a flat plate, fed with the radio energy Forms a beam like a dish, but narrower and with much smaller sidelobes
Less power for a given range
Narrower pulse · better resolution
Exam: directivity is not listed as an advantage of the slotted antenna over the dish; both are directional.
slotted array: narrow, clean beam
Chapter 4 · Antennae
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Another radar aerial is the phased array or slotted antenna: a flat plate with many waveguide-sized slots, fed with the radio energy. It forms a beam like a parabolic dish, but much narrower and with much smaller sidelobes, so it needs less power. The advantages over the dish: narrow beam, reduced sidelobes, less power for a given range, narrower pulse, improved resolution. The exam asks which is not an advantage: directivity, since both are directional.
Summary
What to take into the exam Two aerials Half-wave dipole; quarter-wave Marconi on a ground plane (aircraft).
Length 0.95 × ½ λ or 0.95 × ¼ λ. Short aircraft aerials use an ALU.
Feeders Wire → twin wire → coax → waveguide (½ λ wide) as frequency rises.
Polar diagrams Lines of equal signal. Dipole: torus, circle in plan.
Directivity Reflector 5% longer, ¼ λ behind; shorter directors in front. Price: sidelobes.
Radar Dish: beamwidth 70λ/D. Slotted array: narrower beam, smaller sidelobes, less power.
Chapter 4 · Antennae
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six things to remember: the two basic aerials; the 0.95 length rule and the loading unit; the feeder ladder; what a polar diagram is; how reflectors and directors give directivity and sidelobes; and the dish and slotted array, with the beamwidth formula.
Practice · Questions
Try these 1. The ideal length of a Marconi aerial for 406 MHz is: (a) 36.9 cm (b) 35.1 cm (c) 17.5 cm (d) 18.5 cm
2. A disadvantage of directivity is: (a) reduced range (b) sidelobes (c) phase distortion (d) ambiguity
3. Which is not an advantage of a slotted antenna (phased array)? (a) reduced sidelobes (b) improved resolution (c) reduced power (d) directivity
4. The ideal length of a half-wave dipole for 75 MHz is: (a) 1.9 m (b) 95 cm (c) 3.8 m (d) 47.5 cm
Chapter 4 · Antennae
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The four end-of-chapter questions. Answers on the next slide.
Practice · Answers
Answers and working Q Answer Working 1 (c) 17.5 cm λ = 300 ÷ 406 = 0.739 m; ¼ λ = 18.5 cm; × 0.95 = 17.5 cm 2 (b) Sidelobes Directivity brings unwanted sidelobes 3 (d) Directivity Both dish and slotted array are directional 4 (a) 1.9 m λ = 300 ÷ 75 = 4 m; ½ λ = 2 m; × 0.95 = 1.9 m
Chapter 4 · Antennae
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Questions 1 and 4: the traps are forgetting the 0.95, which gives 18.5 centimetres and 2 metres, or using the wrong fraction of the wavelength.
Try it yourself
Antenna Lab Size a dipole or Marconi aerial for any frequency See which feeder the band needs Compare polar diagrams: dipole, reflector, Yagi, loop, ILS, dish and slotted array Beamwidth calculator for radar dishes Open the Antenna Lab →
beam · sidelobes · nulls
Chapter 4 · Antennae
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The Antenna Lab sizes aerials for any frequency, draws and compares polar diagrams, rotates a loop to find its nulls, and works out radar beamwidths.
eatpl.in · Radio Navigation · Chapter 4
Antenna Lab
Size an aerial for any frequency, then compare polar diagrams and work out radar beamwidths.
Polar diagrams Length Practice
Aerial length
Frequency UnitkHz MHz GHz
125 MHz 406 MHz 75 MHz 118 MHz 136.975 MHz 9.375 GHz
End-of-chapter questions. Set each one up, read the answer in the lab, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.