30.0 29.0 27.9 26.9 25.8 24.8 23.7 22.7 21.7 20.6 19.6 18.5 17.5 16.4 15.4 14.3 13.3 12.3 11.2 10.2 9.1 8.1 7.0 6.0 NMRadio Navigation · Chapter 16
Distance Measuring Equipment Ask the ground how far away you are: pulse pairs, a 50 µs wait and a precise slant range.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
DME is a secondary radar that gives an aircraft its range from a ground station. This chapter covers the frequencies and channels, uses, the pulse technique, jitter and lock-on, range search, beacon saturation, identification, VOR and ILS pairing, coverage, accuracy, slant range and groundspeed.
Chapter roadmap
What this chapter covers 01
The system Rho-theta, the station, frequencies and channels, and what DME is used for.
02
How it measures Pulse pairs, 50 µs delay, jitter and lock-on, search, saturation and ident.
03
Using DME VOR and ILS pairing, coverage, accuracy, slant range and groundspeed.
Chapter 16 · DME
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: the system, how it measures, and using it.
Introduction
Bearing from VOR, range from DME DME: a secondary radar giving the aircraft its range from a ground station VOR gives an accurate magnetic bearing ; DME an accurate slant range Normally co-sited : the ICAO standard rho-theta aid Rho = range, theta = bearing; short range, line of sight θ: VOR radial 060 ρ: DME range 12 nm fix: 060° / 12 nm VOR gives bearing, DME gives slant range
Chapter 16 · DME
03
e-books by eatpl.in · © 2026 · Do not copy or distribute
Distance measuring equipment is a secondary radar that lets an aircraft find its range from a ground station. The pilot gets accurate magnetic bearings from a VOR and accurate slant ranges from a DME. The two are normally co-sited, forming the standard ICAO rho-theta short-range, line-of-sight aid: rho for range, theta for bearing.
01
The system The station, frequencies and uses.
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ground station
A DME on top of a VOR Conventional or Doppler VOR with the DME antenna on top Shown on charts as a VOR symbol inside a square Military TACAN also gives DME range: a VORTAC combines VOR and TACAN Airborne: interrogator, receiver and indicator; selected with the VOR frequency DME antenna (UHF) VOR antenna (VHF) counterpoise equipment shelter
Chapter 16 · DME
05
e-books by eatpl.in · © 2026 · Do not copy or distribute
DME antennas are often mounted on top of a conventional or Doppler VOR. Charts show the combined facility with a VOR symbol in a square. Military TACAN also provides DME range; a VORTAC combines a VOR and a TACAN.
Frequencies
962–1213 MHz, 252 channels, always 63 MHz apart 962 1025 1150 1213 MHz 63 MHz 107X: interrogate 1131 → reply 1194 (+63) 63 MHz 124X: interrogate 1148 → reply 1211 (+63) UHF · 1 MHz spacing · 252 channels (1–126 X and Y) · emission P0N
Channels 962–1213 MHz , UHF, 1 MHz spacing: 252 channels, 1–126 X and 1–126 Y .
63 MHz Interrogation and reply always differ by ± 63 MHz .
Pairing TACAN aircraft select a channel ; civil aircraft select the paired VHF (VOR or ILS) frequency.
Chapter 16 · DME
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
DME, emission code P0N, operates between 962 and 1213 megahertz in the UHF band at 1 megahertz spacing, giving 252 channels numbered 1 to 126 X and 1 to 126 Y. Interrogation and reply always differ by 63 megahertz. Military TACAN aircraft select a channel number; civil aircraft select the paired VHF frequency to get range from a DME or TACAN. For example, MAZ TACAN: aircraft interrogates on 1131, beacon replies on 1194, channel 107X, VHF 116.0. OX DME: 1148 and 1211, channel 124X, VHF 117.7.
Uses of DME
More than a number in a window Position Very accurate slant range : a circular position line; with another DME or a co-sited VOR, a fix .
Groundspeed and time With a computer, the rate of change of range gives groundspeed and time to or from the station.
Holds and arcs More accurate holding patterns and DME arcs .
Approaches Range and height checks on non-precision approaches; ranges to the threshold on ILS/DME.
ATC Radar identification from a VOR/DME position report; separation in non-radar airspace.
RNAV Basis of simple area navigation; accurate inputs to complex RNAV with twin self-selecting DME/DME .
Chapter 16 · DME
07
e-books by eatpl.in · © 2026 · Do not copy or distribute
DME gives very accurate slant range, a circular position line, and with another DME or a co-sited VOR, a fix. With a computer it turns the change of range into groundspeed and elapsed times. It allows more accurate holding and DME arcs, range and height checks on non-precision approaches, accurate ranges to the threshold on ILS/DME procedures, radar identification from VOR/DME position reports, separation in non-radar airspace, and it is the basis for simple RNAV and an input to more complex DME/DME RNAV systems.
02
How it measures Pulses, jitter, search, saturation and ident.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Principle of operation
Pulse pair out, 50 µs wait, pulse pair back ground transponder 50 µs delay interrogation: pulse pair, f reply: same spacing, f ± 63 MHz slant range = (t − 50 µs) ÷ 12.36 µs per nm secondary radar: interrogator in the aircraft, transponder on the groundThe aircraft's interrogator sends pulse pairs omnidirectionally on the transponder's frequency and starts a range search. The ground transponder re-transmits them after 50 µs , 63 MHz away. The aircraft times the interval: a modern DME is accurate to about ± 0.2 nm . Up to about 100 aircraft can use one transponder.
Chapter 16 · DME
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
DME gives slant range by pulse technique. The aircraft's interrogator transmits omnidirectional pulses on the ground transponder's frequency and starts a range search. The transponder re-transmits them after a 50 microsecond delay on a frequency 63 megahertz away. The aircraft picks out its own pulses and measures the time from interrogation to reply, which, at the speed of radio waves, gives very accurate range: a modern DME is inherently accurate to about 0.2 miles. In theory up to 100 aircraft can interrogate one transponder, so each aircraft receives its own replies plus everyone else's on the same frequency.
Pulse pairs
3.5 µs pulses, 12 or 36 µs apart X CHANNEL 12 µs between pulses 12 µs Y CHANNEL 36 µs between pulses 36 µs 3.5 µs wide (≈ 1050 m)Interrogation pulses are 3.5 µs wide (1050 m) and sent in pairs : 12 µs apart on X channels, 36 µs on Y channels.
Chapter 16 · DME
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The interrogation pulses are 3.5 microseconds wide, about 1050 metres, and transmitted in pairs: 12 microseconds apart on X channels and 36 on Y channels.
Picking out your own replies
Jittered pulses, gates and lock-on own transmissions received replies after the gates t same time t after every own pair = locked on twin pulses also reject random single pulses (radars, ignition, lightning)
Jitter Each interrogator sends its pairs at random intervals : a pattern unique to it.
Gates Receiver gates follow the same random pattern; only matching replies get through: lock-on , tracking mode.
Lock and follow Gates move as range changes; the offset t is the slant range.
Chapter 16 · DME
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
To get an unambiguous range, each aircraft's interrogator transmits its pulse pairs at random intervals, jittered, which makes its pattern unique. At each transmission the receiver sets up gates matching that random pattern. The replies on the transponder frequency include everyone's pulses, but only those matching its own pattern pass the gates: lock-on, and the DME enters tracking mode. As range changes the gates move with the replies, the lock-and-follow technique, and the time offset between transmission and reception is the slant range. Twin pulses also mean the receivers never accept random single pulses from other radars, ignition systems or lightning.
Range search
Fast at first, slow once locked Search: 150 pulse pairs/s for 15 000 pairs (100 s ) No lock-on: drops to 60 pps until it locks Locked on: random PRF of about 25 pps Counters sweep 0 → max in 4–5 s (25–30 s in older sets), then restart if no reply NM KT MIN- - - 25.0 60.0 95.0 130.0 165.0 200.0 - - - 25.0 48.0 23.4 23.4 23.4 23.4 23.3 23.3 268 268 269 270 270 270 05 05 05 05 05 05 SEARCHING: counters sweep 0 → max LOCKED ON: tracking 150 pps 60 pps ≈25 pps tracking 15 000 pairs (100 s) no lock yet lock-on
Chapter 16 · DME
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
For a rapid lock-on the interrogator transmits 150 pulse pairs a second for 15 000 pairs, 100 seconds. If it hasn't locked on it drops to 60 a second until it does. At lock-on it works at a random PRF of about 25 a second. During the search the counters or pointer run rapidly from zero to maximum range, in 4 to 5 seconds in modern sets and 25 to 30 in older ones, and if there's no reply they return to zero and start again.
Beacon saturation
2700 pulse pairs a second, about 100 aircraft Assumed: 95% tracking at ≤ 25 pps, 5% searching: average 27 pps per aircraft Beacon output a constant 2700 pps , topped up by receiver noise At 2700 pps received: saturated , receiver gain reduced Weaker, more distant interrogators are excluded and unlock : preference to the nearest A B C D E F Gbelow 2700 pps: everyone gets a range saturated: gain reduced, A, B, E, F, G unlock about 100 aircraft · preference to the nearest
Chapter 16 · DME
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
It's assumed that 95% of aircraft using a beacon are tracking at no more than 25 pulse pairs a second and 5% are searching, an average of 27 per aircraft. A modern beacon's output is a constant 2700 pulse pairs a second; with no aircraft, receiver noise triggers it. When it receives 2700 a second it is saturated and reduces its receiver gain, which excludes the weaker interrogations, about 100 aircraft. Aircraft further away unlock, giving preference to the nearest.
Station identification
Three letters every 30 seconds 3-letter callsign every 30 s , usually with the associated VOR Random pulses replaced by regular pulses keyed with the ident No range measured during the ident: a 10 s memory holds it DME ident tone is higher than the VOR's 0 s 5 s 10 s 15 s 20 s 25 s 30 s 35 s 10 s memory holds the range IDENT 3-letter ident every 30 s regular pulses, higher tone than the VOR ident 23.4 NM KT MIN
Chapter 16 · DME
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
A three-letter callsign is transmitted every 30 seconds, usually with the associated VOR. During the ident the random pulses are replaced by regularly spaced pulses keyed with the letters, so range information isn't available, but the airborne equipment's 10-second memory keeps the range displayed. The DME ident has a different, usually higher, tone than the VOR.
03
Using DME Pairing, coverage, accuracy and groundspeed.
e-books by eatpl.in · © 2026 · Do not copy or distribute
VOR/DME frequency pairing
Associated, same location, or separated ASSOCIATED ≤ 30 m (100 ft) in a TMA · ≤ 600 m (2000 ft) elsewhere VOR/DME OCK e.g. OCK VOR/DME · 115.30 MHz ↔ ch 100X same ident: VOR sends 3 of 4, DME 1 SAME LOCATION, NOT ASSOCIATED further apart but serving the same place VOR ABC DME ABZ e.g. ABC VOR 113.60 + ABZ DME · ch 83X first two letters same, DME ends in Z WIDELY SEPARATED more than 6 nm apart VOR ABC DME XYZ e.g. ABC VOR 113.60 · XYZ DME 12 nm away different idents; may or may not be pairedPairing switches the DME on automatically when you tune the VOR: less workload . Associated: co-located, or within 30 m (100 ft) in a TMA or 600 m (2000 ft) elsewhere, same callsign (four idents per 30 s: VOR three, DME one).
Chapter 16 · DME
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
VORs may be frequency paired with a DME or TACAN, so tuning the VOR automatically selects the DME, which reduces workload. Ideally they're co-sited so range and bearing come from the same point. Associated facilities are co-located, or no more than 30 metres, 100 feet, apart in terminal areas, or 600 metres, 2000 feet, elsewhere; they share the callsign, with four idents every 30 seconds, three from the VOR and one from the DME. Facilities not associated but serving the same location share the first two letters, and the DME's last letter is Z. Widely separated facilities, more than 6 miles apart, have totally different idents and may or may not be paired.
DME range measurement for ILS
Zero at the threshold DME paired with the localiser frequency; supplements or replaces marker beacons Range is zero-referenced to the threshold (UK) Done by reducing the transponder delay Transponder 1500 m away: 5 µs each way, so delay 40 µs threshold DME transponder 1500 m: 5 µs each way delay 40 µs 5 + 40 + 5 = 50 µs: zero range at the threshold selected by tuning the ILS frequency
Chapter 16 · DME
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
DME is also paired with ILS localiser frequencies, supplementing or replacing the marker beacons, with range zero-referenced to the threshold. Since the transponder can't sit on the threshold, its delay is reduced so that the time from the threshold to the transponder, plus the delay, plus the time back to the threshold, is 50 microseconds. With the transponder 1500 metres from the threshold, each way takes 5 microseconds, so the delay becomes 40.
Range and coverage
Line of sight, DOC and echoes Line of sight : higher aircraft and beacon, longer rangeHigh ground blocks it; a steep bank can hide the antenna (memory bridges it) DOC : published protected range and height against co-channel interferenceBeyond the DOC: possible range errors Echo protection circuit rejects reflections line of sight: range blocked by high ground range ≈ 1.25 (√h₁ + √h₂) nm, h in feet DOC: protected range and height; echo protection circuit
Chapter 16 · DME
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
DME obeys the line-of-sight rule, so the higher the aircraft and beacon the greater the range, and intervening high ground blocks it. Bank can hide the aircraft's antenna and interrupt the signals, but the memory prevents any major disruption. Each DME has a published designated operational coverage, a range and height, protecting it from co-channel interference; use beyond the DOC may give range errors. An echo protection circuit eliminates errors from reflections off the ground, buildings or mountains.
Accuracy
± 0.25 nm ± 1.25% of range DME/N (95%): ± 0.25 nm ± 1.25% of range DME/P (precision): ± 0.2 nm Slant range ≠ ground range: significant within 3 × height Overhead it reads your height in nm; small cone of confusion 6 nm high, 10 nm DME: ground range 8 nm (7.625–8.375 with tolerance) cone of confusion DME (slant)10.0 9.2 8.5 7.8 7.2 6.7 6.3 6.1 6.0 ground8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0.0 nm height 36 840 ft = 6 nm · DME 10 → ground √(10² − 6²) = 8 nm slant range matters within 3 × height
Chapter 16 · DME
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a 95% basis, DME for navigation should have a total system error no worse than plus or minus 0.25 miles plus 1.25% of range; precision DME, plus or minus 0.2 miles. The difference between slant range and ground distance grows as the aircraft gets higher and closer, becoming significant within about three times the height. Overhead the DME shows your height in nautical miles, with a small cone of confusion. At 36 840 feet, 6 miles, a 10 mile DME reading is 8 miles on the ground; with the tolerances, 7.625 to 8.375.
Accuracy of groundspeed
Only valid flying straight to or from HOMING valid: flying straight to the station HIGH AND CLOSE under-reads as slant range changes slowly DME ARC circling at constant range: reads zero NM KT MIN12.0 11.7 11.3 11.0 10.7 10.3 10.0 9.7 9.4 300 300 300 300 300 300 300 300 300 02 02 02 02 02 02 02 02 02 height 6 nm NM KT MIN15.2 13.7 12.2 10.7 9.4 8.1 7.1 6.4 6.0 276 270 261 249 230 203 161 99 20 03 03 03 03 02 02 03 04 -- 10 nm NM KT MIN10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 0 0 0 0 0 0 0 0 0 -- -- -- -- -- -- -- -- -- Computed from the rate of change of slant range : it under-reads the closer and higher you are; circling at constant range it reads zero . Only valid when homing to or flying directly away from the station.
Chapter 16 · DME
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
The indicated groundspeed is computed from the rate of change of slant range, so it under-reads more the closer and higher the aircraft is. Circling at constant range it reads zero. It's only valid when homing to or flying directly away from the station.
Summary
What to take into the exam Frequency UHF 962–1213 MHz, 1 MHz, 252 channels; ± 63 MHz; select paired VHF (VOR or ILS).
Principle Aircraft interrogates with jittered pulse pairs; ground replies after 50 µs, 63 MHz away; range = (t − 50) / 12.36.
Pulses Twin pulses reject interference; jitter identifies own replies; 63 MHz stops locking on to reflections.
Search and saturation 150 pps, then 60, then ≈25 at lock-on. Saturation at 2700 pps (≈100 aircraft): gain reduced, nearest kept.
Pairing Associated: co-located or ≤ 100 ft TMA / 2000 ft elsewhere, same ident. Same place: DME ends in Z. > 6 nm: different.
Accuracy ± 0.25 nm ± 1.25%; slant range matters within 3 × height; GS under-reads high and close, zero on an arc.
Chapter 16 · DME
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six summaries: frequency, principle, pulses, search and saturation, pairing, and accuracy.
Practice · Questions 1–11
Try these 1. Airborne DME tells its pulses from others' because: (a) different frequencies (b) only unique twin pulses (c) it rejects pulses not synchronised with its random PRF (d) own frequency
2. A DME beacon transmitting on 962 MHz receives on: (a) 1030 (b) 902 (c) 1025 (d) 962 MHz
3. VOR and DME share the first two letters; the DME's last is Z: (a) co-located (b) more than 600 m apart but serve the same location (c) widely separated (d) max 30 m apart
4. DME is ___ radar on ___ in the ___ band: (a) primary 8800 SHF (b) secondary 1030 UHF (c) secondary 962 MHz UHF (d) primary 9375 SHF
5. A DME transponder ignores other radars because: (a) random rate (b) different frequencies (c) it only accepts unique twin DME pulses (d) only the strongest 100
6. DME accuracy: (a) 3% (b) 1.25% (c) 0.5 nm (d) ± 0.25 nm ± 1.25% of range
7. DME tells its replies from others' because: (a) different frequencies (b) twin pulses (c) random rate, accepts only synchronised replies (d) search accepts correct range only
8. When a transponder saturates: (a) standby (b) more pulse pairs (c) raises the receiver threshold to remove weaker signals (d) selective mode
9. FL250, DME beacon at 400 ft amsl: max range? (a) 210 (b) 198 (c) 175 (d) 222 nm
10. For a VOR and DME to be associated: (a) same VHF frequency (b) separation ≤ 100 ft in a TMA, 2000 ft outside (c) 100 m / 2000 m (d) DME ends in Z
11. The 63 MHz shift prevents: (a) other radars (b) locking on to primary returns of its own transmissions (c) static (d) others' replies
Chapter 16 · DME
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Practice · Questions 12–21
Try these 12. DME accuracy: (a) ± 3% or 0.5 nm (b) ± 1.25% (c) ± 3% (d) ± 0.25 nm ± 1.25% of range
13. Associated if separation ≤ ___ in a terminal area and ___ outside: (a) 100 m 2000 m (b) 50 ft 200 ft (c) 30 m 600 m (d) 50 m 200 m
14. DME is a ___ radar in the ___ band using ___: (a) primary SHF CW (b) secondary UHF twin pulses (c) secondary SHF jittered (d) primary UHF pairs
15. It locks on to its own replies because the receiver only accepts: (a) its own frequency (b) the same frequency (c) replies with the same intervals as its own transmissions (d) constant intervals
16–17. VOR set 045, FROM, needle 1½ dots right (1 dot = 2°), DME 40 nm. 16: radial? (a) 042 (b) 048 (c) 222 (d) 228. 17: on regaining the centreline: (a) left onto 045 (b) right onto 048 (c) left onto 225 (d) right onto 225
18. DME band, pulses and emission: (a) SHF PO1 (b) UHF twin pulses P0N (c) EHF A9F (d) UHF J3E
19. In the initial search: (a) receiver checks 150/s (b) airborne transmitter sends 150 pulse pairs/s (c) ground limits to 150 (d) 24 and 150
20. DME and VOR are frequency paired because: (a) same receiver (b) easy conversion (c) cockpit workload is reduced (d) same site
21. It distinguishes its replies because: (a) different frequencies (b) twin pulses (c) random rate (jitter), accepts only matching replies (d) ± 63 MHz in search
Chapter 16 · DME
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
The questions 12 to 21. Answers next.
Practice · Answers
Answers Q Ans Why 1 c Jitter: only synchronised replies 2 c 962 + 63 = 1025 3 b Z: same location, > 600 m 4 c Secondary, 962 MHz, UHF 5 c Only twin DME pulses 6 d ± 0.25 nm ± 1.25% 7 c Random rate, synchronised replies 8 c Threshold up, weak signals out 9 d 1.25(√25 000 + √400) ≈ 222 10 b 100 ft TMA / 2000 ft 11 b Not its own reflections
Q Ans Why 12 d ± 0.25 nm ± 1.25% 13 c 30 m / 600 m 14 b Secondary, UHF, twin pulses 15 c Same intervals as its own 16 a 3° off: 042 radial 17 a Then left onto 045 18 b UHF, twin pulses, P0N 19 b Transmitter 150 pps 20 c Workload 21 c Jitter
Chapter 16 · DME
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Answers to all 21, with the reason for each.
Fly round a 3D VOR/DME: home, fly away, arc or overfly Watch the search, lock-on, ident and memory Compare DME groundspeed and slant range with the truth Pulse pairs, jitter, channels and saturation Slant, ground, line of sight and ILS delay calculator Open the DME Lab →
23.4 NM 270 KT 05 MIN search · lock · slant · pulses
Chapter 16 · DME
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The DME Lab: flying, pulses and calculations.
eatpl.in · Radio Navigation · Chapter 16
DME Lab
Fly round a VOR/DME and read slant range, groundspeed and time; see the pulses and channels; work out slant and ground range.
Fly Pulses Slant range Practice
Fly the DME
Flight
Home to station Fly away 10 nm DME arc Overfly Free
Steep turn (mask antenna) Ident now Restart Time ×10
Slant range, coverage, ILS delay
21 practice questions. Set each one up in the lab, read the answer, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.
3D view Orbit Chase Top
Drag to turn.